Ejemplos de apollon_flash_init en C++ (Cpp)

Ejemplo n.º 1

Archivo: board-apollon.c Proyecto: 007kumarraja/rockchip-rk3188-mk908

static void __init omap_apollon_init(void)
{
	u32 v;

	omap2420_mux_init(board_mux, OMAP_PACKAGE_ZAC);
	omap_board_config = apollon_config;
	omap_board_config_size = ARRAY_SIZE(apollon_config);

	apollon_init_smc91x();
	apollon_led_init();
	apollon_flash_init();
	apollon_usb_init();

	/* REVISIT: where's the correct place */
	omap_mux_init_signal("sys_nirq", OMAP_PULL_ENA | OMAP_PULL_UP);

	/* LCD PWR_EN */
	omap_mux_init_signal("mcbsp2_dr.gpio_11", OMAP_PULL_ENA | OMAP_PULL_UP);

	/* Use Interal loop-back in MMC/SDIO Module Input Clock selection */
	v = omap_ctrl_readl(OMAP2_CONTROL_DEVCONF0);
	v |= (1 << 24);
	omap_ctrl_writel(v, OMAP2_CONTROL_DEVCONF0);

	/*
 	 * Make sure the serial ports are muxed on at this point.
	 * You have to mux them off in device drivers later on
	 * if not needed.
	 */
	platform_add_devices(apollon_devices, ARRAY_SIZE(apollon_devices));
	omap_serial_init();
}

Ejemplo n.º 2

Archivo: board-apollon.c Proyecto: Lord-Devices/cm_kernel_samsung_hlte

static void __init omap_apollon_init(void)
{
	u32 v;

	omap2420_mux_init(board_mux, OMAP_PACKAGE_ZAC);

	apollon_init_smc91x();
	apollon_led_init();
	apollon_flash_init();
	apollon_usb_init();

	/* REVISIT: where's the correct place */
	omap_mux_init_signal("sys_nirq", OMAP_PULL_ENA | OMAP_PULL_UP);

	/* LCD PWR_EN */
	omap_mux_init_signal("mcbsp2_dr.gpio_11", OMAP_PULL_ENA | OMAP_PULL_UP);

	/* Use Interal loop-back in MMC/SDIO Module Input Clock selection */
	v = omap_ctrl_readl(OMAP2_CONTROL_DEVCONF0);
	v |= (1 << 24);
	omap_ctrl_writel(v, OMAP2_CONTROL_DEVCONF0);

	/*
	 * Make sure the serial ports are muxed on at this point.
	 * You have to mux them off in device drivers later on
	 * if not needed.
	 */
	apollon_smc91x_resources[1].start = gpio_to_irq(APOLLON_ETHR_GPIO_IRQ);
	apollon_smc91x_resources[1].end = gpio_to_irq(APOLLON_ETHR_GPIO_IRQ);
	platform_add_devices(apollon_devices, ARRAY_SIZE(apollon_devices));
	omap_serial_init();
	omap_sdrc_init(NULL, NULL);
	omap_display_init(&apollon_dss_data);
}

Ejemplo n.º 3

Archivo: board-apollon.c Proyecto: Broadcom/stblinux-2.6.31

static void __init omap_apollon_init(void)
{
	u32 v;

	apollon_led_init();
	apollon_flash_init();
	apollon_usb_init();

	/* REVISIT: where's the correct place */
	omap_cfg_reg(W19_24XX_SYS_NIRQ);

	/* Use Interal loop-back in MMC/SDIO Module Input Clock selection */
	v = omap_ctrl_readl(OMAP2_CONTROL_DEVCONF0);
	v |= (1 << 24);
	omap_ctrl_writel(v, OMAP2_CONTROL_DEVCONF0);

	/*
 	 * Make sure the serial ports are muxed on at this point.
	 * You have to mux them off in device drivers later on
	 * if not needed.
	 */
	platform_add_devices(apollon_devices, ARRAY_SIZE(apollon_devices));
	omap_board_config = apollon_config;
	omap_board_config_size = ARRAY_SIZE(apollon_config);
	omap_serial_init();
}

Ejemplo n.º 4

Archivo: board-apollon.c Proyecto: smartassfox/archos_kernel_27

static void __init omap_apollon_init(void)
{
	apollon_cs_init();
	apollon_led_init();
	apollon_flash_init();
	apollon_usb_init();
	apollon_tsc_init();

	/*
 	 * Make sure the serial ports are muxed on at this point.
	 * You have to mux them off in device drivers later on
	 * if not needed.
	 */
	platform_add_devices(apollon_devices, ARRAY_SIZE(apollon_devices));
	omap_board_config = apollon_config;
	omap_board_config_size = ARRAY_SIZE(apollon_config);
	omap_serial_init();
	omap_register_i2c_bus(1, 100, NULL, 0);
	omap_register_i2c_bus(2, 100, NULL, 0);

	spi_register_board_info(apollon_spi_board_info,
				ARRAY_SIZE(apollon_spi_board_info));

	apollon_mmc_init();
}