static __devinit int palmld_pata_probe(struct platform_device *pdev)
{
struct ata_host *host;
struct ata_port *ap;
void __iomem *mem;
int ret;
/* allocate host */
host = ata_host_alloc(&pdev->dev, 1);
if (!host) {
ret = -ENOMEM;
goto err1;
}
/* remap drive's physical memory address */
mem = devm_ioremap(&pdev->dev, PALMLD_IDE_PHYS, 0x1000);
if (!mem) {
ret = -ENOMEM;
goto err1;
}
/* request and activate power GPIO, IRQ GPIO */
ret = gpio_request_array(palmld_hdd_gpios,
ARRAY_SIZE(palmld_hdd_gpios));
if (ret)
goto err1;
/* reset the drive */
gpio_set_value(GPIO_NR_PALMLD_IDE_RESET, 0);
msleep(30);
gpio_set_value(GPIO_NR_PALMLD_IDE_RESET, 1);
msleep(30);
/* setup the ata port */
ap = host->ports[0];
ap->ops = &palmld_port_ops;
ap->pio_mask = ATA_PIO4;
ap->flags |= ATA_FLAG_PIO_POLLING;
/* memory mapping voodoo */
ap->ioaddr.cmd_addr = mem + 0x10;
ap->ioaddr.altstatus_addr = mem + 0xe;
ap->ioaddr.ctl_addr = mem + 0xe;
/* start the port */
ata_sff_std_ports(&ap->ioaddr);
/* activate host */
ret = ata_host_activate(host, 0, NULL, IRQF_TRIGGER_RISING,
&palmld_sht);
if (ret)
goto err2;
return ret;
err2:
gpio_free_array(palmld_hdd_gpios, ARRAY_SIZE(palmld_hdd_gpios));
err1:
return ret;
}
static int ninja32_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
struct ata_host *host;
struct ata_port *ap;
void __iomem *base;
int rc;
host = ata_host_alloc(&dev->dev, 1);
if (!host)
return -ENOMEM;
ap = host->ports[0];
/* Set up the PCI device */
rc = pcim_enable_device(dev);
if (rc)
return rc;
rc = pcim_iomap_regions(dev, 1 << 0, DRV_NAME);
if (rc == -EBUSY)
pcim_pin_device(dev);
if (rc)
return rc;
host->iomap = pcim_iomap_table(dev);
rc = pci_set_dma_mask(dev, ATA_DMA_MASK);
if (rc)
return rc;
rc = pci_set_consistent_dma_mask(dev, ATA_DMA_MASK);
if (rc)
return rc;
pci_set_master(dev);
/* Set up the register mappings. We use the I/O mapping as only the
older chips also have MMIO on BAR 1 */
base = host->iomap[0];
if (!base)
return -ENOMEM;
ap->ops = &ninja32_port_ops;
ap->pio_mask = ATA_PIO4;
ap->flags |= ATA_FLAG_SLAVE_POSS;
ap->ioaddr.cmd_addr = base + 0x10;
ap->ioaddr.ctl_addr = base + 0x1E;
ap->ioaddr.altstatus_addr = base + 0x1E;
ap->ioaddr.bmdma_addr = base;
ata_sff_std_ports(&ap->ioaddr);
ap->pflags = ATA_PFLAG_PIO32 | ATA_PFLAG_PIO32CHANGE;
ninja32_program(base);
/* FIXME: Should we disable them at remove ? */
return ata_host_activate(host, dev->irq, ata_bmdma_interrupt,
IRQF_SHARED, &ninja32_sht);
}
static int isapnp_init_one(struct pnp_dev *idev, const struct pnp_device_id *dev_id)
{
struct ata_host *host;
struct ata_port *ap;
void __iomem *cmd_addr, *ctl_addr;
int irq = 0;
irq_handler_t handler = NULL;
if (pnp_port_valid(idev, 0) == 0)
return -ENODEV;
if (pnp_irq_valid(idev, 0)) {
irq = pnp_irq(idev, 0);
handler = ata_sff_interrupt;
}
/* allocate host */
host = ata_host_alloc(&idev->dev, 1);
if (!host)
return -ENOMEM;
/* acquire resources and fill host */
cmd_addr = devm_ioport_map(&idev->dev, pnp_port_start(idev, 0), 8);
if (!cmd_addr)
return -ENOMEM;
ap = host->ports[0];
ap->ops = &isapnp_noalt_port_ops;
ap->pio_mask = ATA_PIO0;
ap->flags |= ATA_FLAG_SLAVE_POSS;
ap->ioaddr.cmd_addr = cmd_addr;
if (pnp_port_valid(idev, 1)) {
ctl_addr = devm_ioport_map(&idev->dev,
pnp_port_start(idev, 1), 1);
ap->ioaddr.altstatus_addr = ctl_addr;
ap->ioaddr.ctl_addr = ctl_addr;
ap->ops = &isapnp_port_ops;
}
ata_sff_std_ports(&ap->ioaddr);
ata_port_desc(ap, "cmd 0x%llx ctl 0x%llx",
(unsigned long long)pnp_port_start(idev, 0),
(unsigned long long)pnp_port_start(idev, 1));
/* activate */
return ata_host_activate(host, irq, handler, 0,
&isapnp_sht);
}
static int ninja32_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
struct ata_host *host;
struct ata_port *ap;
void __iomem *base;
int rc;
host = ata_host_alloc(&dev->dev, 1);
if (!host)
return -ENOMEM;
ap = host->ports[0];
rc = pcim_enable_device(dev);
if (rc)
return rc;
rc = pcim_iomap_regions(dev, 1 << 0, DRV_NAME);
if (rc == -EBUSY)
pcim_pin_device(dev);
if (rc)
return rc;
host->iomap = pcim_iomap_table(dev);
rc = pci_set_dma_mask(dev, ATA_DMA_MASK);
if (rc)
return rc;
rc = pci_set_consistent_dma_mask(dev, ATA_DMA_MASK);
if (rc)
return rc;
pci_set_master(dev);
base = host->iomap[0];
if (!base)
return -ENOMEM;
ap->ops = &ninja32_port_ops;
ap->pio_mask = ATA_PIO4;
ap->flags |= ATA_FLAG_SLAVE_POSS;
ap->ioaddr.cmd_addr = base + 0x10;
ap->ioaddr.ctl_addr = base + 0x1E;
ap->ioaddr.altstatus_addr = base + 0x1E;
ap->ioaddr.bmdma_addr = base;
ata_sff_std_ports(&ap->ioaddr);
ap->pflags = ATA_PFLAG_PIO32 | ATA_PFLAG_PIO32CHANGE;
ninja32_program(base);
return ata_host_activate(host, dev->irq, ata_sff_interrupt,
IRQF_SHARED, &ninja32_sht);
}
static void vt6421_init_addrs(struct ata_port *ap)
{
void __iomem * const * iomap = ap->host->iomap;
void __iomem *reg_addr = iomap[ap->port_no];
void __iomem *bmdma_addr = iomap[4] + (ap->port_no * 8);
struct ata_ioports *ioaddr = &ap->ioaddr;
ioaddr->cmd_addr = reg_addr;
ioaddr->altstatus_addr =
ioaddr->ctl_addr = (void __iomem *)
((unsigned long)(reg_addr + 8) | ATA_PCI_CTL_OFS);
ioaddr->bmdma_addr = bmdma_addr;
ioaddr->scr_addr = vt6421_scr_addr(iomap[5], ap->port_no);
ata_sff_std_ports(ioaddr);
ata_port_pbar_desc(ap, ap->port_no, -1, "port");
ata_port_pbar_desc(ap, 4, ap->port_no * 8, "bmdma");
}
static void rb532_pata_setup_ports(struct ata_host *ah)
{
struct rb532_cf_info *info = ah->private_data;
struct ata_port *ap;
ap = ah->ports[0];
ap->ops = &rb532_pata_port_ops;
ap->pio_mask = ATA_PIO4;
ap->ioaddr.cmd_addr = info->iobase + RB500_CF_REG_BASE;
ap->ioaddr.ctl_addr = info->iobase + RB500_CF_REG_CTRL;
ap->ioaddr.altstatus_addr = info->iobase + RB500_CF_REG_CTRL;
ata_sff_std_ports(&ap->ioaddr);
ap->ioaddr.data_addr = info->iobase + RB500_CF_REG_DBUF32;
ap->ioaddr.error_addr = info->iobase + RB500_CF_REG_ERR;
}
static void rb153_pata_setup_port(struct ata_host *ah)
{
struct rb153_cf_info *info = ah->private_data;
struct ata_port *ap;
ap = ah->ports[0];
ap->ops = &rb153_pata_port_ops;
ap->pio_mask = 0x1f; /* PIO4 */
ap->flags = ATA_FLAG_NO_LEGACY | ATA_FLAG_MMIO;
ap->ioaddr.cmd_addr = info->iobase + RB153_CF_REG_CMD;
ap->ioaddr.ctl_addr = info->iobase + RB153_CF_REG_CTRL;
ap->ioaddr.altstatus_addr = info->iobase + RB153_CF_REG_CTRL;
ata_sff_std_ports(&ap->ioaddr);
ap->ioaddr.data_addr = info->iobase + RB153_CF_REG_DATA;
}
static int atp867x_ata_pci_sff_init_host(struct ata_host *host)
{
struct device *gdev = host->dev;
struct pci_dev *pdev = to_pci_dev(gdev);
unsigned int mask = 0;
int i, rc;
/*
* do not map rombase
*/
rc = pcim_iomap_regions(pdev, 1 << ATP867X_BAR_IOBASE, DRV_NAME);
if (rc == -EBUSY)
pcim_pin_device(pdev);
if (rc)
return rc;
host->iomap = pcim_iomap_table(pdev);
#ifdef ATP867X_DEBUG
atp867x_check_res(pdev);
for (i = 0; i < PCI_ROM_RESOURCE; i++)
printk(KERN_DEBUG "ATP867X: iomap[%d]=0x%llx\n", i,
(unsigned long long)(host->iomap[i]));
#endif
/*
* request, iomap BARs and init port addresses accordingly
*/
for (i = 0; i < host->n_ports; i++) {
struct ata_port *ap = host->ports[i];
struct ata_ioports *ioaddr = &ap->ioaddr;
ioaddr->cmd_addr = ATP867X_IO_PORTBASE(ap, i);
ioaddr->ctl_addr = ioaddr->altstatus_addr
= ATP867X_IO_ALTSTATUS(ap, i);
ioaddr->bmdma_addr = ATP867X_IO_DMABASE(ap, i);
ata_sff_std_ports(ioaddr);
rc = atp867x_set_priv(ap);
if (rc)
return rc;
#ifdef ATP867X_DEBUG
atp867x_check_ports(ap, i);
#endif
ata_port_desc(ap, "cmd 0x%lx ctl 0x%lx",
(unsigned long)ioaddr->cmd_addr,
(unsigned long)ioaddr->ctl_addr);
ata_port_desc(ap, "bmdma 0x%lx",
(unsigned long)ioaddr->bmdma_addr);
mask |= 1 << i;
}
if (!mask) {
dev_printk(KERN_ERR, gdev, "no available native port\n");
return -ENODEV;
}
atp867x_fixup(host);
rc = pci_set_dma_mask(pdev, ATA_DMA_MASK);
if (rc)
return rc;
rc = pci_set_consistent_dma_mask(pdev, ATA_DMA_MASK);
return rc;
}
static int sil680_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
{
static const struct ata_port_info info = {
.flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = ATA_PIO4,
.mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA6,
.port_ops = &sil680_port_ops
};
static const struct ata_port_info info_slow = {
.flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = ATA_PIO4,
.mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA5,
.port_ops = &sil680_port_ops
};
const struct ata_port_info *ppi[] = { &info, NULL };
struct ata_host *host;
void __iomem *mmio_base;
int rc, try_mmio;
ata_print_version_once(&pdev->dev, DRV_VERSION);
rc = pcim_enable_device(pdev);
if (rc)
return rc;
switch (sil680_init_chip(pdev, &try_mmio)) {
case 0:
ppi[0] = &info_slow;
break;
case 0x30:
return -ENODEV;
}
if (!try_mmio)
goto use_ioports;
/* Try to acquire MMIO resources and fallback to PIO if
* that fails
*/
rc = pcim_iomap_regions(pdev, 1 << SIL680_MMIO_BAR, DRV_NAME);
if (rc)
goto use_ioports;
/* Allocate host and set it up */
host = ata_host_alloc_pinfo(&pdev->dev, ppi, 2);
if (!host)
return -ENOMEM;
host->iomap = pcim_iomap_table(pdev);
/* Setup DMA masks */
rc = pci_set_dma_mask(pdev, ATA_DMA_MASK);
if (rc)
return rc;
rc = pci_set_consistent_dma_mask(pdev, ATA_DMA_MASK);
if (rc)
return rc;
pci_set_master(pdev);
/* Get MMIO base and initialize port addresses */
mmio_base = host->iomap[SIL680_MMIO_BAR];
host->ports[0]->ioaddr.bmdma_addr = mmio_base + 0x00;
host->ports[0]->ioaddr.cmd_addr = mmio_base + 0x80;
host->ports[0]->ioaddr.ctl_addr = mmio_base + 0x8a;
host->ports[0]->ioaddr.altstatus_addr = mmio_base + 0x8a;
ata_sff_std_ports(&host->ports[0]->ioaddr);
host->ports[1]->ioaddr.bmdma_addr = mmio_base + 0x08;
host->ports[1]->ioaddr.cmd_addr = mmio_base + 0xc0;
host->ports[1]->ioaddr.ctl_addr = mmio_base + 0xca;
host->ports[1]->ioaddr.altstatus_addr = mmio_base + 0xca;
ata_sff_std_ports(&host->ports[1]->ioaddr);
/* Register & activate */
return ata_host_activate(host, pdev->irq, ata_bmdma_interrupt,
IRQF_SHARED, &sil680_sht);
use_ioports:
return ata_pci_bmdma_init_one(pdev, ppi, &sil680_sht, NULL, 0);
}
static int cs5520_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
{
static const unsigned int cmd_port[] = { 0x1F0, 0x170 };
static const unsigned int ctl_port[] = { 0x3F6, 0x376 };
struct ata_port_info pi = {
.flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = ATA_PIO4,
.port_ops = &cs5520_port_ops,
};
const struct ata_port_info *ppi[2];
u8 pcicfg;
void __iomem *iomap[5];
struct ata_host *host;
struct ata_ioports *ioaddr;
int i, rc;
rc = pcim_enable_device(pdev);
if (rc)
return rc;
/* IDE port enable bits */
pci_read_config_byte(pdev, 0x60, &pcicfg);
/* Check if the ATA ports are enabled */
if ((pcicfg & 3) == 0)
return -ENODEV;
ppi[0] = ppi[1] = &ata_dummy_port_info;
if (pcicfg & 1)
ppi[0] = π
if (pcicfg & 2)
ppi[1] = π
if ((pcicfg & 0x40) == 0) {
dev_warn(&pdev->dev, "DMA mode disabled. Enabling.\n");
pci_write_config_byte(pdev, 0x60, pcicfg | 0x40);
}
pi.mwdma_mask = id->driver_data;
host = ata_host_alloc_pinfo(&pdev->dev, ppi, 2);
if (!host)
return -ENOMEM;
/* Perform set up for DMA */
if (pci_enable_device_io(pdev)) {
printk(KERN_ERR DRV_NAME ": unable to configure BAR2.\n");
return -ENODEV;
}
if (pci_set_dma_mask(pdev, DMA_BIT_MASK(32))) {
printk(KERN_ERR DRV_NAME ": unable to configure DMA mask.\n");
return -ENODEV;
}
if (pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(32))) {
printk(KERN_ERR DRV_NAME ": unable to configure consistent DMA mask.\n");
return -ENODEV;
}
/* Map IO ports and initialize host accordingly */
iomap[0] = devm_ioport_map(&pdev->dev, cmd_port[0], 8);
iomap[1] = devm_ioport_map(&pdev->dev, ctl_port[0], 1);
iomap[2] = devm_ioport_map(&pdev->dev, cmd_port[1], 8);
iomap[3] = devm_ioport_map(&pdev->dev, ctl_port[1], 1);
iomap[4] = pcim_iomap(pdev, 2, 0);
if (!iomap[0] || !iomap[1] || !iomap[2] || !iomap[3] || !iomap[4])
return -ENOMEM;
ioaddr = &host->ports[0]->ioaddr;
ioaddr->cmd_addr = iomap[0];
ioaddr->ctl_addr = iomap[1];
ioaddr->altstatus_addr = iomap[1];
ioaddr->bmdma_addr = iomap[4];
ata_sff_std_ports(ioaddr);
ata_port_desc(host->ports[0],
"cmd 0x%x ctl 0x%x", cmd_port[0], ctl_port[0]);
ata_port_pbar_desc(host->ports[0], 4, 0, "bmdma");
ioaddr = &host->ports[1]->ioaddr;
ioaddr->cmd_addr = iomap[2];
ioaddr->ctl_addr = iomap[3];
ioaddr->altstatus_addr = iomap[3];
ioaddr->bmdma_addr = iomap[4] + 8;
ata_sff_std_ports(ioaddr);
ata_port_desc(host->ports[1],
"cmd 0x%x ctl 0x%x", cmd_port[1], ctl_port[1]);
ata_port_pbar_desc(host->ports[1], 4, 8, "bmdma");
/* activate the host */
pci_set_master(pdev);
rc = ata_host_start(host);
if (rc)
return rc;
for (i = 0; i < 2; i++) {
static const int irq[] = { 14, 15 };
struct ata_port *ap = host->ports[i];
if (ata_port_is_dummy(ap))
continue;
rc = devm_request_irq(&pdev->dev, irq[ap->port_no],
ata_bmdma_interrupt, 0, DRV_NAME, host);
if (rc)
return rc;
ata_port_desc(ap, "irq %d", irq[i]);
}
return ata_host_register(host, &cs5520_sht);
}
static int pata_ftide010_probe(struct platform_device *pdev)
{
struct device *dev = &pdev->dev;
struct device_node *np = dev->of_node;
struct ata_port_info pi = ftide010_port_info;
const struct ata_port_info *ppi[] = { &pi, NULL };
struct ftide010 *ftide;
struct resource *res;
int irq;
int ret;
int i;
ftide = devm_kzalloc(dev, sizeof(*ftide), GFP_KERNEL);
if (!ftide)
return -ENOMEM;
ftide->dev = dev;
irq = platform_get_irq(pdev, 0);
if (irq < 0)
return irq;
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
if (!res)
return -ENODEV;
ftide->base = devm_ioremap_resource(dev, res);
if (IS_ERR(ftide->base))
return PTR_ERR(ftide->base);
ftide->pclk = devm_clk_get(dev, "PCLK");
if (!IS_ERR(ftide->pclk)) {
ret = clk_prepare_enable(ftide->pclk);
if (ret) {
dev_err(dev, "failed to enable PCLK\n");
return ret;
}
}
/* Some special Cortina Gemini init, if needed */
if (of_device_is_compatible(np, "cortina,gemini-pata")) {
/*
* We need to know which instance is probing (the
* Gemini has two instances of FTIDE010) and we do
* this simply by looking at the physical base
* address, which is 0x63400000 for ATA1, else we
* are ATA0. This will also set up the cable types.
*/
ret = pata_ftide010_gemini_init(ftide,
&pi,
(res->start == 0x63400000));
if (ret)
goto err_dis_clk;
} else {
/* Else assume we are connected using PATA40 */
ftide->master_cbl = ATA_CBL_PATA40;
ftide->slave_cbl = ATA_CBL_PATA40;
}
ftide->host = ata_host_alloc_pinfo(dev, ppi, 1);
if (!ftide->host) {
ret = -ENOMEM;
goto err_dis_clk;
}
ftide->host->private_data = ftide;
for (i = 0; i < ftide->host->n_ports; i++) {
struct ata_port *ap = ftide->host->ports[i];
struct ata_ioports *ioaddr = &ap->ioaddr;
ioaddr->bmdma_addr = ftide->base + FTIDE010_DMA_REG;
ioaddr->cmd_addr = ftide->base + FTIDE010_CMD_DATA;
ioaddr->ctl_addr = ftide->base + FTIDE010_ALTSTAT_CTRL;
ioaddr->altstatus_addr = ftide->base + FTIDE010_ALTSTAT_CTRL;
ata_sff_std_ports(ioaddr);
}
dev_info(dev, "device ID %08x, irq %d, reg %pR\n",
readl(ftide->base + FTIDE010_IDE_DEVICE_ID), irq, res);
ret = ata_host_activate(ftide->host, irq, ata_bmdma_interrupt,
0, &pata_ftide010_sht);
if (ret)
goto err_dis_clk;
return 0;
err_dis_clk:
if (!IS_ERR(ftide->pclk))
clk_disable_unprepare(ftide->pclk);
return ret;
}
static int __devinit cs5520_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
{
static const unsigned int cmd_port[] = { 0x1F0, 0x170 };
static const unsigned int ctl_port[] = { 0x3F6, 0x376 };
struct ata_port_info pi = {
.flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.port_ops = &cs5520_port_ops,
};
const struct ata_port_info *ppi[2];
u8 pcicfg;
void __iomem *iomap[5];
struct ata_host *host;
struct ata_ioports *ioaddr;
int i, rc;
rc = pcim_enable_device(pdev);
if (rc)
return rc;
/* IDE port enable bits */
pci_read_config_byte(pdev, 0x60, &pcicfg);
/* Check if the ATA ports are enabled */
if ((pcicfg & 3) == 0)
return -ENODEV;
ppi[0] = ppi[1] = &ata_dummy_port_info;
if (pcicfg & 1)
ppi[0] = π
if (pcicfg & 2)
ppi[1] = π
if ((pcicfg & 0x40) == 0) {
dev_printk(KERN_WARNING, &pdev->dev,
"DMA mode disabled. Enabling.\n");
pci_write_config_byte(pdev, 0x60, pcicfg | 0x40);
}
pi.mwdma_mask = id->driver_data;
host = ata_host_alloc_pinfo(&pdev->dev, ppi, 2);
if (!host)
return -ENOMEM;
/* Perform set up for DMA */
if (pci_enable_device_bars(pdev, 1<<2)) {
printk(KERN_ERR DRV_NAME ": unable to configure BAR2.\n");
return -ENODEV;
}
if (pci_set_dma_mask(pdev, DMA_32BIT_MASK)) {
printk(KERN_ERR DRV_NAME ": unable to configure DMA mask.\n");
return -ENODEV;
}
if (pci_set_consistent_dma_mask(pdev, DMA_32BIT_MASK)) {
printk(KERN_ERR DRV_NAME ": unable to configure consistent DMA mask.\n");
return -ENODEV;
}
/* Map IO ports and initialize host accordingly */
iomap[0] = devm_ioport_map(&pdev->dev, cmd_port[0], 8);
iomap[1] = devm_ioport_map(&pdev->dev, ctl_port[0], 1);
iomap[2] = devm_ioport_map(&pdev->dev, cmd_port[1], 8);
iomap[3] = devm_ioport_map(&pdev->dev, ctl_port[1], 1);
iomap[4] = pcim_iomap(pdev, 2, 0);
if (!iomap[0] || !iomap[1] || !iomap[2] || !iomap[3] || !iomap[4])
return -ENOMEM;
ioaddr = &host->ports[0]->ioaddr;
ioaddr->cmd_addr = iomap[0];
ioaddr->ctl_addr = iomap[1];
ioaddr->altstatus_addr = iomap[1];
ioaddr->bmdma_addr = iomap[4];
ata_sff_std_ports(ioaddr);
ata_port_desc(host->ports[0],
"cmd 0x%x ctl 0x%x", cmd_port[0], ctl_port[0]);
ata_port_pbar_desc(host->ports[0], 4, 0, "bmdma");
ioaddr = &host->ports[1]->ioaddr;
ioaddr->cmd_addr = iomap[2];
ioaddr->ctl_addr = iomap[3];
ioaddr->altstatus_addr = iomap[3];
ioaddr->bmdma_addr = iomap[4] + 8;
ata_sff_std_ports(ioaddr);
ata_port_desc(host->ports[1],
"cmd 0x%x ctl 0x%x", cmd_port[1], ctl_port[1]);
ata_port_pbar_desc(host->ports[1], 4, 8, "bmdma");
/* activate the host */
pci_set_master(pdev);
rc = ata_host_start(host);
if (rc)
return rc;
for (i = 0; i < 2; i++) {
static const int irq[] = { 14, 15 };
struct ata_port *ap = host->ports[i];
if (ata_port_is_dummy(ap))
continue;
rc = devm_request_irq(&pdev->dev, irq[ap->port_no],
ata_sff_interrupt, 0, DRV_NAME, host);
if (rc)
return rc;
ata_port_desc(ap, "irq %d", irq[i]);
}
return ata_host_register(host, &cs5520_sht);
}
#ifdef CONFIG_PM
/**
* cs5520_reinit_one - device resume
* @pdev: PCI device
*
* Do any reconfiguration work needed by a resume from RAM. We need
* to restore DMA mode support on BIOSen which disabled it
*/
static int cs5520_reinit_one(struct pci_dev *pdev)
{
struct ata_host *host = dev_get_drvdata(&pdev->dev);
u8 pcicfg;
int rc;
rc = ata_pci_device_do_resume(pdev);
if (rc)
return rc;
pci_read_config_byte(pdev, 0x60, &pcicfg);
if ((pcicfg & 0x40) == 0)
pci_write_config_byte(pdev, 0x60, pcicfg | 0x40);
ata_host_resume(host);
return 0;
}
/**
* cs5520_pci_device_suspend - device suspend
* @pdev: PCI device
*
* We have to cut and waste bits from the standard method because
* the 5520 is a bit odd and not just a pure ATA device. As a result
* we must not disable it. The needed code is short and this avoids
* chip specific mess in the core code.
*/
static int cs5520_pci_device_suspend(struct pci_dev *pdev, pm_message_t mesg)
{
struct ata_host *host = dev_get_drvdata(&pdev->dev);
int rc = 0;
rc = ata_host_suspend(host, mesg);
if (rc)
return rc;
pci_save_state(pdev);
return 0;
}
#endif /* CONFIG_PM */
/* For now keep DMA off. We can set it for all but A rev CS5510 once the
core ATA code can handle it */
static const struct pci_device_id pata_cs5520[] = {
{ PCI_VDEVICE(CYRIX, PCI_DEVICE_ID_CYRIX_5510), },
{ PCI_VDEVICE(CYRIX, PCI_DEVICE_ID_CYRIX_5520), },
{ },
};
static struct pci_driver cs5520_pci_driver = {
.name = DRV_NAME,
.id_table = pata_cs5520,
.probe = cs5520_init_one,
.remove = ata_pci_remove_one,
#ifdef CONFIG_PM
.suspend = cs5520_pci_device_suspend,
.resume = cs5520_reinit_one,
#endif
};
static int __init cs5520_init(void)
{
return pci_register_driver(&cs5520_pci_driver);
}
static void __exit cs5520_exit(void)
{
pci_unregister_driver(&cs5520_pci_driver);
}
static int hpt3x3_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
{
static int printed_version;
static const struct ata_port_info info = {
.flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = ATA_PIO4,
#if defined(CONFIG_PATA_HPT3X3_DMA)
/* Further debug needed */
.mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA2,
#endif
.port_ops = &hpt3x3_port_ops
};
/* Register offsets of taskfiles in BAR4 area */
static const u8 offset_cmd[2] = { 0x20, 0x28 };
static const u8 offset_ctl[2] = { 0x36, 0x3E };
const struct ata_port_info *ppi[] = { &info, NULL };
struct ata_host *host;
int i, rc;
void __iomem *base;
hpt3x3_init_chipset(pdev);
if (!printed_version++)
dev_printk(KERN_DEBUG, &pdev->dev, "version " DRV_VERSION "\n");
host = ata_host_alloc_pinfo(&pdev->dev, ppi, 2);
if (!host)
return -ENOMEM;
/* acquire resources and fill host */
rc = pcim_enable_device(pdev);
if (rc)
return rc;
/* Everything is relative to BAR4 if we set up this way */
rc = pcim_iomap_regions(pdev, 1 << 4, DRV_NAME);
if (rc == -EBUSY)
pcim_pin_device(pdev);
if (rc)
return rc;
host->iomap = pcim_iomap_table(pdev);
rc = pci_set_dma_mask(pdev, ATA_DMA_MASK);
if (rc)
return rc;
rc = pci_set_consistent_dma_mask(pdev, ATA_DMA_MASK);
if (rc)
return rc;
base = host->iomap[4]; /* Bus mastering base */
for (i = 0; i < host->n_ports; i++) {
struct ata_port *ap = host->ports[i];
struct ata_ioports *ioaddr = &ap->ioaddr;
ioaddr->cmd_addr = base + offset_cmd[i];
ioaddr->altstatus_addr =
ioaddr->ctl_addr = base + offset_ctl[i];
ioaddr->scr_addr = NULL;
ata_sff_std_ports(ioaddr);
ioaddr->bmdma_addr = base + 8 * i;
ata_port_pbar_desc(ap, 4, -1, "ioport");
ata_port_pbar_desc(ap, 4, offset_cmd[i], "cmd");
}
pci_set_master(pdev);
return ata_host_activate(host, pdev->irq, ata_sff_interrupt,
IRQF_SHARED, &hpt3x3_sht);
}
static int __devinit sil680_init_one(struct pci_dev *pdev,
const struct pci_device_id *id)
{
static const struct ata_port_info info = {
.flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
.udma_mask = ATA_UDMA6,
.port_ops = &sil680_port_ops
};
static const struct ata_port_info info_slow = {
.flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
.udma_mask = ATA_UDMA5,
.port_ops = &sil680_port_ops
};
const struct ata_port_info *ppi[] = { &info, NULL };
static int printed_version;
struct ata_host *host;
void __iomem *mmio_base;
int rc, try_mmio;
struct pci_dev *drac;
/* DRAC only filter */
drac = pci_get_device(PCI_VENDOR_ID_DELL, PCI_DEVICE_ID_DELL_RAC4,
NULL);
if (drac == NULL) {
/* There are two common devices on DRACs. See if we can *
* find the second one if couldn't find the first. */
printk(KERN_INFO "sil680: Trying SMIC device.\n");
drac = pci_get_device(PCI_VENDOR_ID_DELL, 0x0014, NULL);
}
if (drac == NULL)
return -ENODEV;
if (drac->bus != pdev->bus) /* Not the right SIL680 */
{
pci_dev_put(drac);
return -ENODEV;
}
pci_dev_put(drac);
/* Back to original code */
if (!printed_version++)
dev_printk(KERN_DEBUG, &pdev->dev, "version " DRV_VERSION "\n");
rc = pcim_enable_device(pdev);
if (rc)
return rc;
switch (sil680_init_chip(pdev, &try_mmio)) {
case 0:
ppi[0] = &info_slow;
break;
case 0x30:
return -ENODEV;
}
if (!try_mmio)
goto use_ioports;
/* Try to acquire MMIO resources and fallback to PIO if
* that fails
*/
rc = pcim_enable_device(pdev);
if (rc)
return rc;
rc = pcim_iomap_regions(pdev, 1 << SIL680_MMIO_BAR, DRV_NAME);
if (rc)
goto use_ioports;
/* Allocate host and set it up */
host = ata_host_alloc_pinfo(&pdev->dev, ppi, 2);
if (!host)
return -ENOMEM;
host->iomap = pcim_iomap_table(pdev);
/* Setup DMA masks */
rc = pci_set_dma_mask(pdev, ATA_DMA_MASK);
if (rc)
return rc;
rc = pci_set_consistent_dma_mask(pdev, ATA_DMA_MASK);
if (rc)
return rc;
pci_set_master(pdev);
/* Get MMIO base and initialize port addresses */
mmio_base = host->iomap[SIL680_MMIO_BAR];
host->ports[0]->ioaddr.bmdma_addr = mmio_base + 0x00;
host->ports[0]->ioaddr.cmd_addr = mmio_base + 0x80;
host->ports[0]->ioaddr.ctl_addr = mmio_base + 0x8a;
host->ports[0]->ioaddr.altstatus_addr = mmio_base + 0x8a;
ata_sff_std_ports(&host->ports[0]->ioaddr);
host->ports[1]->ioaddr.bmdma_addr = mmio_base + 0x08;
host->ports[1]->ioaddr.cmd_addr = mmio_base + 0xc0;
host->ports[1]->ioaddr.ctl_addr = mmio_base + 0xca;
host->ports[1]->ioaddr.altstatus_addr = mmio_base + 0xca;
ata_sff_std_ports(&host->ports[1]->ioaddr);
/* Register & activate */
return ata_host_activate(host, pdev->irq, ata_sff_interrupt,
IRQF_SHARED, &sil680_sht);
use_ioports:
return ata_pci_sff_init_one(pdev, ppi, &sil680_sht, NULL);
}
#ifdef CONFIG_PM
static int sil680_reinit_one(struct pci_dev *pdev)
{
struct ata_host *host = dev_get_drvdata(&pdev->dev);
int try_mmio, rc;
rc = ata_pci_device_do_resume(pdev);
if (rc)
return rc;
sil680_init_chip(pdev, &try_mmio);
ata_host_resume(host);
return 0;
}
#endif
static const struct pci_device_id sil680[] = {
{ PCI_VDEVICE(CMD, PCI_DEVICE_ID_SII_680), },
{ },
};
static struct pci_driver sil680_pci_driver = {
.name = DRV_NAME,
.id_table = sil680,
.probe = sil680_init_one,
.remove = ata_pci_remove_one,
#ifdef CONFIG_PM
.suspend = ata_pci_device_suspend,
.resume = sil680_reinit_one,
#endif
};
static int __init sil680_init(void)
{
return pci_register_driver(&sil680_pci_driver);
}
static void __exit sil680_exit(void)
{
pci_unregister_driver(&sil680_pci_driver);
}
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("low-level driver for SI680 PATA");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, sil680);
MODULE_VERSION(DRV_VERSION);
module_init(sil680_init);
module_exit(sil680_exit);