static int __init pb1200_init_irq(void)
{
/* We have a problem with CPLD rev 3. */
if (BCSR_WHOAMI_CPLD(bcsr_read(BCSR_WHOAMI)) <= 3) {
printk(KERN_ERR "WARNING!!!\n");
printk(KERN_ERR "WARNING!!!\n");
printk(KERN_ERR "WARNING!!!\n");
printk(KERN_ERR "WARNING!!!\n");
printk(KERN_ERR "WARNING!!!\n");
printk(KERN_ERR "WARNING!!!\n");
printk(KERN_ERR "Pb1200 must be at CPLD rev 4. Please have Pb1200\n");
printk(KERN_ERR "updated to latest revision. This software will\n");
printk(KERN_ERR "not work on anything less than CPLD rev 4.\n");
printk(KERN_ERR "WARNING!!!\n");
printk(KERN_ERR "WARNING!!!\n");
printk(KERN_ERR "WARNING!!!\n");
printk(KERN_ERR "WARNING!!!\n");
printk(KERN_ERR "WARNING!!!\n");
printk(KERN_ERR "WARNING!!!\n");
panic("Game over. Your score is 0.");
}
set_irq_type(AU1200_GPIO7_INT, IRQF_TRIGGER_LOW);
bcsr_init_irq(PB1200_INT_BEGIN, PB1200_INT_END, AU1200_GPIO7_INT);
return 0;
}
static int __init db1300_device_init(void)
{
int swapped, cpldirq;
/* setup CPLD IRQ muxer */
cpldirq = au1300_gpio_to_irq(AU1300_PIN_EXTCLK1);
irq_set_irq_type(cpldirq, IRQ_TYPE_LEVEL_HIGH);
bcsr_init_irq(DB1300_FIRST_INT, DB1300_LAST_INT, cpldirq);
/* insert/eject IRQs: one always triggers so don't enable them
* when doing request_irq() on them. DB1200 has this bug too.
*/
irq_set_status_flags(DB1300_SD1_INSERT_INT, IRQ_NOAUTOEN);
irq_set_status_flags(DB1300_SD1_EJECT_INT, IRQ_NOAUTOEN);
irq_set_status_flags(DB1300_CF_INSERT_INT, IRQ_NOAUTOEN);
irq_set_status_flags(DB1300_CF_EJECT_INT, IRQ_NOAUTOEN);
/*
* setup board
*/
prom_get_ethernet_addr(&db1300_eth_config.mac[0]);
i2c_register_board_info(0, db1300_i2c_devs,
ARRAY_SIZE(db1300_i2c_devs));
/* Audio PSC clock is supplied by codecs (PSC1, 2) */
__raw_writel(PSC_SEL_CLK_SERCLK,
(void __iomem *)KSEG1ADDR(AU1300_PSC1_PHYS_ADDR) + PSC_SEL_OFFSET);
wmb();
__raw_writel(PSC_SEL_CLK_SERCLK,
(void __iomem *)KSEG1ADDR(AU1300_PSC2_PHYS_ADDR) + PSC_SEL_OFFSET);
wmb();
/* I2C uses internal 48MHz EXTCLK1 */
__raw_writel(PSC_SEL_CLK_INTCLK,
(void __iomem *)KSEG1ADDR(AU1300_PSC3_PHYS_ADDR) + PSC_SEL_OFFSET);
wmb();
/* enable power to USB ports */
bcsr_mod(BCSR_RESETS, 0, BCSR_RESETS_USBHPWR | BCSR_RESETS_OTGPWR);
/* although it is socket #0, it uses the CPLD bits which previous boards
* have used for socket #1.
*/
db1x_register_pcmcia_socket(
AU1000_PCMCIA_ATTR_PHYS_ADDR,
AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x00400000 - 1,
AU1000_PCMCIA_MEM_PHYS_ADDR,
AU1000_PCMCIA_MEM_PHYS_ADDR + 0x00400000 - 1,
AU1000_PCMCIA_IO_PHYS_ADDR,
AU1000_PCMCIA_IO_PHYS_ADDR + 0x00010000 - 1,
DB1300_CF_INT, DB1300_CF_INSERT_INT, 0, DB1300_CF_EJECT_INT, 1);
swapped = bcsr_read(BCSR_STATUS) & BCSR_STATUS_DB1200_SWAPBOOT;
db1x_register_norflash(64 << 20, 2, swapped);
return platform_add_devices(db1300_dev, ARRAY_SIZE(db1300_dev));
}
static int __init db1300_device_init(void)
{
int swapped, cpldirq;
cpldirq = au1300_gpio_to_irq(AU1300_PIN_EXTCLK1);
irq_set_irq_type(cpldirq, IRQ_TYPE_LEVEL_HIGH);
bcsr_init_irq(DB1300_FIRST_INT, DB1300_LAST_INT, cpldirq);
irq_set_status_flags(DB1300_SD1_INSERT_INT, IRQ_NOAUTOEN);
irq_set_status_flags(DB1300_SD1_EJECT_INT, IRQ_NOAUTOEN);
irq_set_status_flags(DB1300_CF_INSERT_INT, IRQ_NOAUTOEN);
irq_set_status_flags(DB1300_CF_EJECT_INT, IRQ_NOAUTOEN);
prom_get_ethernet_addr(&db1300_eth_config.mac[0]);
i2c_register_board_info(0, db1300_i2c_devs,
ARRAY_SIZE(db1300_i2c_devs));
__raw_writel(PSC_SEL_CLK_SERCLK,
(void __iomem *)KSEG1ADDR(AU1300_PSC1_PHYS_ADDR) + PSC_SEL_OFFSET);
wmb();
__raw_writel(PSC_SEL_CLK_SERCLK,
(void __iomem *)KSEG1ADDR(AU1300_PSC2_PHYS_ADDR) + PSC_SEL_OFFSET);
wmb();
__raw_writel(PSC_SEL_CLK_INTCLK,
(void __iomem *)KSEG1ADDR(AU1300_PSC3_PHYS_ADDR) + PSC_SEL_OFFSET);
wmb();
bcsr_mod(BCSR_RESETS, 0, BCSR_RESETS_USBHPWR | BCSR_RESETS_OTGPWR);
db1x_register_pcmcia_socket(
AU1000_PCMCIA_ATTR_PHYS_ADDR,
AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x00400000 - 1,
AU1000_PCMCIA_MEM_PHYS_ADDR,
AU1000_PCMCIA_MEM_PHYS_ADDR + 0x00400000 - 1,
AU1000_PCMCIA_IO_PHYS_ADDR,
AU1000_PCMCIA_IO_PHYS_ADDR + 0x00010000 - 1,
DB1300_CF_INT, DB1300_CF_INSERT_INT, 0, DB1300_CF_EJECT_INT, 1);
swapped = bcsr_read(BCSR_STATUS) & BCSR_STATUS_DB1200_SWAPBOOT;
db1x_register_norflash(64 << 20, 2, swapped);
return platform_add_devices(db1300_dev, ARRAY_SIZE(db1300_dev));
}
int __init db1200_dev_setup(void)
{
unsigned long pfc;
unsigned short sw;
int swapped, bid;
struct clk *c;
bid = BCSR_WHOAMI_BOARD(bcsr_read(BCSR_WHOAMI));
if ((bid == BCSR_WHOAMI_PB1200_DDR1) ||
(bid == BCSR_WHOAMI_PB1200_DDR2)) {
if (pb1200_res_fixup())
return -ENODEV;
}
/* GPIO7 is low-level triggered CPLD cascade */
irq_set_irq_type(AU1200_GPIO7_INT, IRQ_TYPE_LEVEL_LOW);
bcsr_init_irq(DB1200_INT_BEGIN, DB1200_INT_END, AU1200_GPIO7_INT);
/* SMBus/SPI on PSC0, Audio on PSC1 */
pfc = alchemy_rdsys(AU1000_SYS_PINFUNC);
pfc &= ~(SYS_PINFUNC_P0A | SYS_PINFUNC_P0B);
pfc &= ~(SYS_PINFUNC_P1A | SYS_PINFUNC_P1B | SYS_PINFUNC_FS3);
pfc |= SYS_PINFUNC_P1C; /* SPI is configured later */
alchemy_wrsys(pfc, AU1000_SYS_PINFUNC);
/* get 50MHz for I2C driver on PSC0 */
c = clk_get(NULL, "psc0_intclk");
if (!IS_ERR(c)) {
pfc = clk_round_rate(c, 50000000);
if ((pfc < 1) || (abs(50000000 - pfc) > 2500000))
pr_warn("DB1200: cant get I2C close to 50MHz\n");
else
clk_set_rate(c, pfc);
clk_put(c);
}
/* insert/eject pairs: one of both is always screaming. To avoid
* issues they must not be automatically enabled when initially
* requested.
*/
irq_set_status_flags(DB1200_SD0_INSERT_INT, IRQ_NOAUTOEN);
irq_set_status_flags(DB1200_SD0_EJECT_INT, IRQ_NOAUTOEN);
irq_set_status_flags(DB1200_PC0_INSERT_INT, IRQ_NOAUTOEN);
irq_set_status_flags(DB1200_PC0_EJECT_INT, IRQ_NOAUTOEN);
irq_set_status_flags(DB1200_PC1_INSERT_INT, IRQ_NOAUTOEN);
irq_set_status_flags(DB1200_PC1_EJECT_INT, IRQ_NOAUTOEN);
i2c_register_board_info(0, db1200_i2c_devs,
ARRAY_SIZE(db1200_i2c_devs));
spi_register_board_info(db1200_spi_devs,
ARRAY_SIZE(db1200_i2c_devs));
/* SWITCHES: S6.8 I2C/SPI selector (OFF=I2C ON=SPI)
* S6.7 AC97/I2S selector (OFF=AC97 ON=I2S)
* or S12 on the PB1200.
*/
/* NOTE: GPIO215 controls OTG VBUS supply. In SPI mode however
* this pin is claimed by PSC0 (unused though, but pinmux doesn't
* allow to free it without crippling the SPI interface).
* As a result, in SPI mode, OTG simply won't work (PSC0 uses
* it as an input pin which is pulled high on the boards).
*/
pfc = alchemy_rdsys(AU1000_SYS_PINFUNC) & ~SYS_PINFUNC_P0A;
/* switch off OTG VBUS supply */
gpio_request(215, "otg-vbus");
gpio_direction_output(215, 1);
printk(KERN_INFO "%s device configuration:\n", get_system_type());
sw = bcsr_read(BCSR_SWITCHES);
if (sw & BCSR_SWITCHES_DIP_8) {
db1200_devs[0] = &db1200_i2c_dev;
bcsr_mod(BCSR_RESETS, BCSR_RESETS_PSC0MUX, 0);
pfc |= (2 << 17); /* GPIO2 block owns GPIO215 */
printk(KERN_INFO " S6.8 OFF: PSC0 mode I2C\n");
printk(KERN_INFO " OTG port VBUS supply available!\n");
} else {
db1200_devs[0] = &db1200_spi_dev;
bcsr_mod(BCSR_RESETS, 0, BCSR_RESETS_PSC0MUX);
pfc |= (1 << 17); /* PSC0 owns GPIO215 */
printk(KERN_INFO " S6.8 ON : PSC0 mode SPI\n");
printk(KERN_INFO " OTG port VBUS supply disabled\n");
}
alchemy_wrsys(pfc, AU1000_SYS_PINFUNC);
/* Audio: DIP7 selects I2S(0)/AC97(1), but need I2C for I2S!
* so: DIP7=1 || DIP8=0 => AC97, DIP7=0 && DIP8=1 => I2S
*/
sw &= BCSR_SWITCHES_DIP_8 | BCSR_SWITCHES_DIP_7;
if (sw == BCSR_SWITCHES_DIP_8) {
bcsr_mod(BCSR_RESETS, 0, BCSR_RESETS_PSC1MUX);
db1200_audio_dev.name = "au1xpsc_i2s";
db1200_sound_dev.name = "db1200-i2s";
printk(KERN_INFO " S6.7 ON : PSC1 mode I2S\n");
} else {
bcsr_mod(BCSR_RESETS, BCSR_RESETS_PSC1MUX, 0);
db1200_audio_dev.name = "au1xpsc_ac97";
db1200_sound_dev.name = "db1200-ac97";
printk(KERN_INFO " S6.7 OFF: PSC1 mode AC97\n");
}
/* Audio PSC clock is supplied externally. (FIXME: platdata!!) */
c = clk_get(NULL, "psc1_intclk");
if (!IS_ERR(c)) {
clk_prepare_enable(c);
clk_put(c);
}
__raw_writel(PSC_SEL_CLK_SERCLK,
(void __iomem *)KSEG1ADDR(AU1550_PSC1_PHYS_ADDR) + PSC_SEL_OFFSET);
wmb();
db1x_register_pcmcia_socket(
AU1000_PCMCIA_ATTR_PHYS_ADDR,
AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
AU1000_PCMCIA_MEM_PHYS_ADDR,
AU1000_PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1,
AU1000_PCMCIA_IO_PHYS_ADDR,
AU1000_PCMCIA_IO_PHYS_ADDR + 0x000010000 - 1,
DB1200_PC0_INT, DB1200_PC0_INSERT_INT,
/*DB1200_PC0_STSCHG_INT*/0, DB1200_PC0_EJECT_INT, 0);
db1x_register_pcmcia_socket(
AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x004000000,
AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x004400000 - 1,
AU1000_PCMCIA_MEM_PHYS_ADDR + 0x004000000,
AU1000_PCMCIA_MEM_PHYS_ADDR + 0x004400000 - 1,
AU1000_PCMCIA_IO_PHYS_ADDR + 0x004000000,
AU1000_PCMCIA_IO_PHYS_ADDR + 0x004010000 - 1,
DB1200_PC1_INT, DB1200_PC1_INSERT_INT,
/*DB1200_PC1_STSCHG_INT*/0, DB1200_PC1_EJECT_INT, 1);
swapped = bcsr_read(BCSR_STATUS) & BCSR_STATUS_DB1200_SWAPBOOT;
db1x_register_norflash(64 << 20, 2, swapped);
platform_add_devices(db1200_devs, ARRAY_SIZE(db1200_devs));
/* PB1200 is a DB1200 with a 2nd MMC and Camera connector */
if ((bid == BCSR_WHOAMI_PB1200_DDR1) ||
(bid == BCSR_WHOAMI_PB1200_DDR2))
platform_add_devices(pb1200_devs, ARRAY_SIZE(pb1200_devs));
return 0;
}
