void targetConfiguration(void)
{
#ifdef KISSCC
// alternative defaults settings for Beebrain target
boardAlignmentMutable()->rollDegrees = 180;
boardAlignmentMutable()->pitchDegrees = 0;
boardAlignmentMutable()->yawDegrees = 0;
#endif
}
void updateBoardAlignment(int16_t roll, int16_t pitch)
{
const float sinAlignYaw = sin_approx(DECIDEGREES_TO_RADIANS(boardAlignment()->yawDeciDegrees));
const float cosAlignYaw = cos_approx(DECIDEGREES_TO_RADIANS(boardAlignment()->yawDeciDegrees));
boardAlignmentMutable()->rollDeciDegrees += -sinAlignYaw * pitch + cosAlignYaw * roll;
boardAlignmentMutable()->pitchDeciDegrees += cosAlignYaw * pitch + sinAlignYaw * roll;
initBoardAlignment();
}
void targetConfiguration(void)
{
if (getDetectedMotorType() == MOTOR_BRUSHED) {
motorConfigMutable()->dev.motorPwmRate = BRUSHED_MOTORS_PWM_RATE;
motorConfigMutable()->minthrottle = 1050; // for 6mm and 7mm brushed
}
/* Default to Spektrum */
rxConfigMutable()->serialrx_provider = SERIALRX_SPEKTRUM2048; // all DSM* except DSM2 22ms
rxConfigMutable()->spektrum_sat_bind = 5; // DSM2 11ms
rxConfigMutable()->spektrum_sat_bind_autoreset = 1;
rxConfigMutable()->mincheck = 1025;
rxConfigMutable()->rcInterpolation = RC_SMOOTHING_MANUAL;
rxConfigMutable()->rcInterpolationInterval = 14;
parseRcChannels("TAER1234", rxConfigMutable());
mixerConfigMutable()->yaw_motors_reversed = true;
imuConfigMutable()->small_angle = 180;
blackboxConfigMutable()->p_ratio = 128;
/* Breadboard-specific settings for development purposes only
*/
#if defined(BREADBOARD)
boardAlignmentMutable()->pitchDegrees = 90; // vertical breakout board
barometerConfigMutable()->baro_hardware = BARO_DEFAULT; // still testing not on V1 or V2 pcb
#else
barometerConfigMutable()->baro_hardware = BARO_NONE;
#endif
compassConfigMutable()->mag_hardware = MAG_NONE;
systemConfigMutable()->cpu_overclock = 2; //216MHZ
pidConfigMutable()->runaway_takeoff_prevention = false;
featureEnable((FEATURE_DYNAMIC_FILTER | FEATURE_AIRMODE | FEATURE_ANTI_GRAVITY) ^ FEATURE_RX_PARALLEL_PWM);
/* AlienWhoop PIDs tested with 6mm and 7mm motors on most frames */
for (uint8_t pidProfileIndex = 0; pidProfileIndex < PID_PROFILE_COUNT; pidProfileIndex++) {
pidProfile_t *pidProfile = pidProfilesMutable(pidProfileIndex);
pidProfile->pidSumLimit = 1000;
pidProfile->pidSumLimitYaw = 1000;
/* AlienWhoop PIDs tested with 6mm and 7mm motors on most frames */
pidProfile->pid[PID_PITCH].P = 115;
pidProfile->pid[PID_PITCH].I = 75;
pidProfile->pid[PID_PITCH].D = 95;
pidProfile->pid[PID_ROLL].P = 110;
pidProfile->pid[PID_ROLL].I = 75;
pidProfile->pid[PID_ROLL].D = 85;
pidProfile->pid[PID_YAW].P = 220;
pidProfile->pid[PID_YAW].I = 75;
pidProfile->pid[PID_YAW].D = 20;
pidProfile->pid[PID_LEVEL].P = 65;
pidProfile->pid[PID_LEVEL].I = 65;
pidProfile->pid[PID_LEVEL].D = 55;
/* Setpoints */
pidProfile->dterm_filter_type = FILTER_BIQUAD;
pidProfile->dterm_notch_hz = 0;
pidProfile->pid[PID_PITCH].F = 100;
pidProfile->pid[PID_ROLL].F = 100;
pidProfile->feedForwardTransition = 0;
/* Anti-Gravity */
pidProfile->itermThrottleThreshold = 500;
pidProfile->itermAcceleratorGain = 5000;
pidProfile->levelAngleLimit = 65;
}
for (uint8_t rateProfileIndex = 0; rateProfileIndex < CONTROL_RATE_PROFILE_COUNT; rateProfileIndex++) {
controlRateConfig_t *controlRateConfig = controlRateProfilesMutable(rateProfileIndex);
/* RC Rates */
controlRateConfig->rcRates[FD_ROLL] = 218;
controlRateConfig->rcRates[FD_PITCH] = 218;
controlRateConfig->rcRates[FD_YAW] = 218;
/* Classic Expo */
controlRateConfig->rcExpo[FD_ROLL] = 45;
controlRateConfig->rcExpo[FD_PITCH] = 45;
controlRateConfig->rcExpo[FD_YAW] = 45;
/* Super Expo Rates */
controlRateConfig->rates[FD_ROLL] = 0;
controlRateConfig->rates[FD_PITCH] = 0;
controlRateConfig->rates[FD_YAW] = 0;
/* Throttle PID Attenuation (TPA) */
controlRateConfig->dynThrPID = 0; // tpa_rate off
controlRateConfig->tpa_breakpoint = 1600;
/* Force the clipping mixer at 100% seems better for brushed than default (off) and scaling)? */
controlRateConfig->throttle_limit_type = THROTTLE_LIMIT_TYPE_CLIP;
//controlRateConfig->throttle_limit_percent = 100;
controlRateConfig->thrExpo8 = 20; // 20% throttle expo
}
}
