static __init int da850_evm_init_cpufreq(void)
{
switch (system_rev & 0xF) {
case 3:
da850_max_speed = 456000;
break;
case 2:
da850_max_speed = 408000;
break;
case 1:
da850_max_speed = 372000;
break;
}
return da850_register_cpufreq("pll0_sysclk3");
}
static void __init mityomapl138_init(void)
{
int ret;
/* for now, no special EDMA channels are reserved */
ret = da850_register_edma(NULL);
if (ret)
pr_warning("edma registration failed: %d\n", ret);
ret = da8xx_register_watchdog();
if (ret)
pr_warning("watchdog registration failed: %d\n", ret);
davinci_serial_init(&mityomapl138_uart_config);
ret = da8xx_register_i2c(0, &mityomap_i2c_0_pdata);
if (ret)
pr_warning("i2c0 registration failed: %d\n", ret);
ret = pmic_tps65023_init();
if (ret)
pr_warning("TPS65023 PMIC init failed: %d\n", ret);
mityomapl138_setup_nand();
mityomapl138_config_emac();
ret = da8xx_register_rtc();
if (ret)
pr_warning("rtc setup failed: %d\n", ret);
ret = da850_register_cpufreq("pll0_sysclk3");
if (ret)
pr_warning("cpufreq registration failed: %d\n", ret);
ret = da8xx_register_cpuidle();
if (ret)
pr_warning("cpuidle registration failed: %d\n", ret);
ret = da850_register_pm(&da850_pm_device);
if (ret)
pr_warning("da850_evm_init: suspend registration failed: %d\n",
ret);
}
static __init void da850_evm_init(void)
{
int ret;
ret = pmic_tps65070_init();
if (ret)
pr_warning("da850_evm_init: TPS65070 PMIC init failed: %d\n",
ret);
ret = da850_register_edma(da850_edma_rsv);
if (ret)
pr_warning("da850_evm_init: edma registration failed: %d\n",
ret);
ret = davinci_cfg_reg_list(da850_i2c0_pins);
if (ret)
pr_warning("da850_evm_init: i2c0 mux setup failed: %d\n",
ret);
ret = da8xx_register_i2c(0, &da850_evm_i2c_0_pdata);
if (ret)
pr_warning("da850_evm_init: i2c0 registration failed: %d\n",
ret);
ret = da8xx_register_watchdog();
if (ret)
pr_warning("da830_evm_init: watchdog registration failed: %d\n",
ret);
if (HAS_MMC) {
ret = davinci_cfg_reg_list(da850_mmcsd0_pins);
if (ret)
pr_warning("da850_evm_init: mmcsd0 mux setup failed:"
" %d\n", ret);
ret = gpio_request(DA850_MMCSD_CD_PIN, "MMC CD\n");
if (ret)
pr_warning("da850_evm_init: can not open GPIO %d\n",
DA850_MMCSD_CD_PIN);
gpio_direction_input(DA850_MMCSD_CD_PIN);
ret = gpio_request(DA850_MMCSD_WP_PIN, "MMC WP\n");
if (ret)
pr_warning("da850_evm_init: can not open GPIO %d\n",
DA850_MMCSD_WP_PIN);
gpio_direction_input(DA850_MMCSD_WP_PIN);
ret = da8xx_register_mmcsd0(&da850_mmc_config);
if (ret)
pr_warning("da850_evm_init: mmcsd0 registration failed:"
" %d\n", ret);
}
davinci_serial_init(&da850_evm_uart_config);
i2c_register_board_info(1, da850_evm_i2c_devices,
ARRAY_SIZE(da850_evm_i2c_devices));
/*
* shut down uart 0 and 1; they are not used on the board and
* accessing them causes endless "too much work in irq53" messages
* with arago fs
*/
__raw_writel(0, IO_ADDRESS(DA8XX_UART1_BASE) + 0x30);
__raw_writel(0, IO_ADDRESS(DA8XX_UART0_BASE) + 0x30);
ret = davinci_cfg_reg_list(da850_mcasp_pins);
if (ret)
pr_warning("da850_evm_init: mcasp mux setup failed: %d\n",
ret);
da8xx_register_mcasp(0, &da850_evm_snd_data);
ret = davinci_cfg_reg_list(da850_lcdcntl_pins);
if (ret)
pr_warning("da850_evm_init: lcdcntl mux setup failed: %d\n",
ret);
/* Handle board specific muxing for LCD here */
ret = davinci_cfg_reg_list(da850_evm_lcdc_pins);
if (ret)
pr_warning("da850_evm_init: evm specific lcd mux setup "
"failed: %d\n", ret);
ret = da850_lcd_hw_init();
if (ret)
pr_warning("da850_evm_init: lcd initialization failed: %d\n",
ret);
sharp_lk043t1dg01_pdata.panel_power_ctrl = da850_panel_power_ctrl,
ret = da8xx_register_lcdc(&sharp_lk043t1dg01_pdata);
if (ret)
pr_warning("da850_evm_init: lcdc registration failed: %d\n",
ret);
ret = da8xx_register_rtc();
if (ret)
pr_warning("da850_evm_init: rtc setup failed: %d\n", ret);
ret = da850_register_cpufreq();
if (ret)
pr_warning("da850_evm_init: cpufreq registration failed: %d\n",
ret);
ret = da8xx_register_cpuidle();
if (ret)
pr_warning("da850_evm_init: cpuidle registration failed: %d\n",
ret);
ret = da850_register_pm(&da850_pm_device);
if (ret)
pr_warning("da850_evm_init: suspend registration failed: %d\n",
ret);
}
