/**
* dwc3_otg_sm_work - workqueue function.
*
* @w: Pointer to the dwc3 otg workqueue
*
* NOTE: After any change in phy->state,
* we must reschdule the state machine.
*/
static void dwc3_otg_sm_work(struct work_struct *w)
{
struct dwc3_otg *dotg = container_of(w, struct dwc3_otg, sm_work.work);
struct usb_phy *phy = dotg->otg.phy;
struct dwc3_charger *charger = dotg->charger;
bool work = 0;
int ret = 0;
unsigned long delay = 0;
pm_runtime_resume(phy->dev);
dev_dbg(phy->dev, "%s state\n", otg_state_string(phy->state));
/* Check OTG state */
switch (phy->state) {
case OTG_STATE_UNDEFINED:
dwc3_otg_init_sm(dotg);
if (!dotg->psy) {
dotg->psy = power_supply_get_by_name("usb");
if (!dotg->psy)
dev_err(phy->dev,
"couldn't get usb power supply\n");
}
/* Switch to A or B-Device according to ID / BSV */
if (!test_bit(ID, &dotg->inputs)) {
dev_dbg(phy->dev, "!id\n");
phy->state = OTG_STATE_A_IDLE;
work = 1;
} else if (test_bit(B_SESS_VLD, &dotg->inputs)) {
dev_dbg(phy->dev, "b_sess_vld\n");
phy->state = OTG_STATE_B_IDLE;
work = 1;
} else {
phy->state = OTG_STATE_B_IDLE;
dev_dbg(phy->dev, "No device, trying to suspend\n");
pm_runtime_put_sync(phy->dev);
}
break;
case OTG_STATE_B_IDLE:
if (!test_bit(ID, &dotg->inputs)) {
dev_dbg(phy->dev, "!id\n");
phy->state = OTG_STATE_A_IDLE;
work = 1;
dotg->charger_retry_count = 0;
if (charger) {
if (charger->chg_type == DWC3_INVALID_CHARGER)
charger->start_detection(dotg->charger,
false);
else
charger->chg_type =
DWC3_INVALID_CHARGER;
}
} else if (test_bit(B_SESS_VLD, &dotg->inputs)) {
dev_dbg(phy->dev, "b_sess_vld\n");
if (charger) {
/* Has charger been detected? If no detect it */
switch (charger->chg_type) {
case DWC3_DCP_CHARGER:
case DWC3_PROPRIETARY_CHARGER:
dev_dbg(phy->dev, "lpm, DCP charger\n");
dwc3_otg_set_power(phy,
DWC3_IDEV_CHG_MAX);
pm_runtime_put_sync(phy->dev);
break;
case DWC3_CDP_CHARGER:
dwc3_otg_set_power(phy,
DWC3_IDEV_CHG_MAX);
dwc3_otg_start_peripheral(&dotg->otg,
1);
phy->state = OTG_STATE_B_PERIPHERAL;
work = 1;
break;
case DWC3_SDP_CHARGER:
dwc3_otg_start_peripheral(&dotg->otg,
1);
phy->state = OTG_STATE_B_PERIPHERAL;
work = 1;
break;
case DWC3_FLOATED_CHARGER:
#ifdef CONFIG_ZTEMT_COMM_CHARGE
dev_dbg(phy->dev, "lpm, FLOATED charger\n");
dwc3_otg_set_power(phy,
DWC3_IDEV_CHG_MAX);
pm_runtime_put_sync(phy->dev);
#else
if (dotg->charger_retry_count <
max_chgr_retry_count)
dotg->charger_retry_count++;
/*
* In case of floating charger, if
* retry count equal to max retry count
* notify PMIC about floating charger
* and put Hw in low power mode. Else
* perform charger detection again by
* calling start_detection() with false
* and then with true argument.
*/
if (dotg->charger_retry_count ==
max_chgr_retry_count) {
dwc3_otg_set_power(phy, 0);
pm_runtime_put_sync(phy->dev);
break;
}
charger->start_detection(dotg->charger,
false);
#endif
default:
dev_dbg(phy->dev, "chg_det started\n");
charger->start_detection(charger, true);
break;
}
} else {
/* no charger registered, start peripheral */
if (dwc3_otg_start_peripheral(&dotg->otg, 1)) {
/*
* Probably set_peripheral not called
* yet. We will re-try as soon as it
* will be called
*/
dev_err(phy->dev, "enter lpm as\n"
"unable to start B-device\n");
phy->state = OTG_STATE_UNDEFINED;
pm_runtime_put_sync(phy->dev);
return;
}
}
} else {
if (charger)
charger->start_detection(dotg->charger, false);
dotg->charger_retry_count = 0;
dwc3_otg_set_power(phy, 0);
dev_dbg(phy->dev, "No device, trying to suspend\n");
pm_runtime_put_sync(phy->dev);
}
break;
case OTG_STATE_B_PERIPHERAL:
if (!test_bit(B_SESS_VLD, &dotg->inputs) ||
!test_bit(ID, &dotg->inputs)) {
dev_dbg(phy->dev, "!id || !bsv\n");
dwc3_otg_start_peripheral(&dotg->otg, 0);
phy->state = OTG_STATE_B_IDLE;
if (charger)
charger->chg_type = DWC3_INVALID_CHARGER;
work = 1;
}
break;
case OTG_STATE_A_IDLE:
/* Switch to A-Device*/
if (test_bit(ID, &dotg->inputs)) {
dev_dbg(phy->dev, "id\n");
phy->state = OTG_STATE_B_IDLE;
dotg->vbus_retry_count = 0;
work = 1;
} else {
phy->state = OTG_STATE_A_HOST;
ret = dwc3_otg_start_host(&dotg->otg, 1);
if ((ret == -EPROBE_DEFER) &&
dotg->vbus_retry_count < 3) {
/*
* Get regulator failed as regulator driver is
* not up yet. Will try to start host after 1sec
*/
phy->state = OTG_STATE_A_IDLE;
dev_dbg(phy->dev, "Unable to get vbus regulator. Retrying...\n");
delay = VBUS_REG_CHECK_DELAY;
work = 1;
dotg->vbus_retry_count++;
} else if (ret) {
/*
* Probably set_host was not called yet.
* We will re-try as soon as it will be called
*/
dev_dbg(phy->dev, "enter lpm as\n"
"unable to start A-device\n");
phy->state = OTG_STATE_A_IDLE;
pm_runtime_put_sync(phy->dev);
return;
}
}
break;
case OTG_STATE_A_HOST:
if (test_bit(ID, &dotg->inputs)) {
dev_dbg(phy->dev, "id\n");
dwc3_otg_start_host(&dotg->otg, 0);
phy->state = OTG_STATE_B_IDLE;
dotg->vbus_retry_count = 0;
work = 1;
}
break;
default:
dev_err(phy->dev, "%s: invalid otg-state\n", __func__);
}
if (work)
queue_delayed_work(system_nrt_wq, &dotg->sm_work, delay);
}
/**
* dwc3_otg_sm_work - workqueue function.
*
* @w: Pointer to the dwc3 otg workqueue
*
* NOTE: After any change in phy->state,
* we must reschdule the state machine.
*/
static void dwc3_otg_sm_work(struct work_struct *w)
{
struct dwc3_otg *dotg = container_of(w, struct dwc3_otg, sm_work.work);
struct usb_phy *phy = dotg->otg.phy;
struct dwc3_charger *charger = dotg->charger;
bool work = 0;
int ret = 0;
unsigned long delay = 0;
pm_runtime_resume(phy->dev);
dev_dbg(phy->dev, "%s state\n", otg_state_string(phy->state));
/* Check OTG state */
switch (phy->state) {
case OTG_STATE_UNDEFINED:
dwc3_otg_init_sm(dotg);
if (!dotg->psy) {
dotg->psy = power_supply_get_by_name("usb");
if (!dotg->psy)
dev_err(phy->dev,
"couldn't get usb power supply\n");
}
/* Switch to A or B-Device according to ID / BSV */
if (!test_bit(ID, &dotg->inputs)) {
dev_dbg(phy->dev, "!id\n");
phy->state = OTG_STATE_A_IDLE;
work = 1;
} else if (test_bit(B_SESS_VLD, &dotg->inputs)) {
dev_dbg(phy->dev, "b_sess_vld\n");
phy->state = OTG_STATE_B_IDLE;
work = 1;
} else {
phy->state = OTG_STATE_B_IDLE;
dev_dbg(phy->dev, "No device, trying to suspend\n");
pm_runtime_put_sync(phy->dev);
}
break;
case OTG_STATE_B_IDLE:
if (!test_bit(ID, &dotg->inputs)) {
dev_dbg(phy->dev, "!id\n");
phy->state = OTG_STATE_A_IDLE;
work = 1;
dotg->charger_retry_count = 0;
if (charger) {
if (charger->chg_type == DWC3_INVALID_CHARGER)
charger->start_detection(dotg->charger,
false);
else
charger->chg_type =
DWC3_INVALID_CHARGER;
}
} else if (test_bit(B_SESS_VLD, &dotg->inputs)) {
dev_dbg(phy->dev, "b_sess_vld\n");
if (charger) {
/* Has charger been detected? If no detect it */
switch (charger->chg_type) {
case DWC3_DCP_CHARGER:
case DWC3_PROPRIETARY_CHARGER:
dev_dbg(phy->dev, "lpm, DCP charger\n");
dwc3_otg_set_power(phy,
DWC3_IDEV_CHG_MAX);
pm_runtime_put_sync(phy->dev);
break;
case DWC3_CDP_CHARGER:
dwc3_otg_set_power(phy,
DWC3_IDEV_CHG_MAX);
dwc3_otg_start_peripheral(&dotg->otg,
1);
phy->state = OTG_STATE_B_PERIPHERAL;
work = 1;
break;
case DWC3_SDP_CHARGER:
dwc3_otg_start_peripheral(&dotg->otg,
1);
phy->state = OTG_STATE_B_PERIPHERAL;
pr_info("DWC3_SDP_CHARGER\n");
work = 1;
break;
case DWC3_FLOATED_CHARGER:
if (dotg->charger_retry_count <
max_chgr_retry_count)
dotg->charger_retry_count++;
/*
* In case of floating charger, if
* retry count equal to max retry count
* notify PMIC about floating charger
* and put Hw in low power mode. Else
* perform charger detection again by
* calling start_detection() with false
* and then with true argument.
*/
if (dotg->charger_retry_count ==
max_chgr_retry_count) {
dwc3_otg_set_power(phy, 0);
pm_runtime_put_sync(phy->dev);
break;
}
charger->start_detection(dotg->charger,
false);
default:
dev_dbg(phy->dev, "chg_det started\n");
charger->start_detection(charger, true);
break;
}
} else {
/* no charger registered, start peripheral */
if (dwc3_otg_start_peripheral(&dotg->otg, 1)) {
/*
* Probably set_peripheral not called
* yet. We will re-try as soon as it
* will be called
*/
dev_err(phy->dev, "enter lpm as\n"
"unable to start B-device\n");
phy->state = OTG_STATE_UNDEFINED;
pm_runtime_put_sync(phy->dev);
return;
}
}
} else {
if (charger)
charger->start_detection(dotg->charger, false);
dotg->charger_retry_count = 0;
dwc3_otg_set_power(phy, 0);
dev_dbg(phy->dev, "No device, trying to suspend\n");
pm_runtime_put_sync(phy->dev);
}
break;
case OTG_STATE_B_PERIPHERAL:
#ifdef CONFIG_PANTECH_USB_BLOCKING_MDMSTATE
if (get_pantech_mdm_state())
dwc3_otg_set_power(phy, DWC3_BLOCKING_USB_MDMSTATE_MAX);
#endif
#ifndef CONFIG_PANTECH_SIO_BUG_FIX
if (!test_bit(B_SESS_VLD, &dotg->inputs) ||
!test_bit(ID, &dotg->inputs)) {
#else
if (!test_bit(B_SESS_VLD, &dotg->inputs)) {
#endif
dev_dbg(phy->dev, "!id || !bsv\n");
dwc3_otg_start_peripheral(&dotg->otg, 0);
phy->state = OTG_STATE_B_IDLE;
if (charger)
charger->chg_type = DWC3_INVALID_CHARGER;
work = 1;
}
break;
case OTG_STATE_A_IDLE:
/* Switch to A-Device*/
if (test_bit(ID, &dotg->inputs)) {
dev_dbg(phy->dev, "id\n");
phy->state = OTG_STATE_B_IDLE;
dotg->vbus_retry_count = 0;
work = 1;
} else {
phy->state = OTG_STATE_A_HOST;
ret = dwc3_otg_start_host(&dotg->otg, 1);
if ((ret == -EPROBE_DEFER) &&
dotg->vbus_retry_count < 3) {
/*
* Get regulator failed as regulator driver is
* not up yet. Will try to start host after 1sec
*/
phy->state = OTG_STATE_A_IDLE;
dev_dbg(phy->dev, "Unable to get vbus regulator. Retrying...\n");
delay = VBUS_REG_CHECK_DELAY;
work = 1;
dotg->vbus_retry_count++;
} else if (ret) {
/*
* Probably set_host was not called yet.
* We will re-try as soon as it will be called
*/
dev_dbg(phy->dev, "enter lpm as\n"
"unable to start A-device\n");
phy->state = OTG_STATE_A_IDLE;
pm_runtime_put_sync(phy->dev);
return;
}
}
break;
case OTG_STATE_A_HOST:
if (test_bit(ID, &dotg->inputs)) {
dev_dbg(phy->dev, "id\n");
#ifdef CONFIG_PANTECH_SIO_BUG_FIX
/* FIXME : If OTG cable is disconnecting, below process is must completed
* before pm_runtime_suspend.
* So we are ignored pm_runtime_suspend request.
* LS4-USB tarial
*/
pm_runtime_get_noresume(phy->dev);
#endif
dwc3_otg_start_host(&dotg->otg, 0);
phy->state = OTG_STATE_B_IDLE;
dotg->vbus_retry_count = 0;
work = 1;
#ifdef CONFIG_PANTECH_SIO_BUG_FIX
pm_runtime_put_noidle(phy->dev);
#endif
}
break;
default:
dev_err(phy->dev, "%s: invalid otg-state\n", __func__);
}
if (work)
queue_delayed_work(system_nrt_wq, &dotg->sm_work, delay);
}
/**
* dwc3_otg_reset - reset dwc3 otg registers.
*
* @w: Pointer to the dwc3 otg workqueue
*/
static void dwc3_otg_reset(struct dwc3_otg *dotg)
{
static int once;
struct dwc3_ext_xceiv *ext_xceiv = dotg->ext_xceiv;
/*
* OCFG[2] - OTG-Version = 1
* OCFG[1] - HNPCap = 0
* OCFG[0] - SRPCap = 0
*/
if (ext_xceiv && !ext_xceiv->otg_capability)
dwc3_writel(dotg->regs, DWC3_OCFG, 0x4);
/*
* OCTL[6] - PeriMode = 1
* OCTL[5] - PrtPwrCtl = 0
* OCTL[4] - HNPReq = 0
* OCTL[3] - SesReq = 0
* OCTL[2] - TermSelDLPulse = 0
* OCTL[1] - DevSetHNPEn = 0
* OCTL[0] - HstSetHNPEn = 0
*/
if (!once) {
if (ext_xceiv && !ext_xceiv->otg_capability)
dwc3_writel(dotg->regs, DWC3_OCTL, 0x40);
once++;
}
/* Clear all otg events (interrupts) indications */
dwc3_writel(dotg->regs, DWC3_OEVT, 0xFFFF);
/* Enable ID/BSV StsChngEn event*/
if (ext_xceiv && !ext_xceiv->otg_capability)
dwc3_writel(dotg->regs, DWC3_OEVTEN,
DWC3_OEVTEN_OTGCONIDSTSCHNGEVNT |
DWC3_OEVTEN_OTGBDEVVBUSCHNGEVNT);
}
/**
* dwc3_otg_init - Initializes otg related registers
* @dwc: Pointer to out controller context structure
*
* Returns 0 on success otherwise negative errno.
*/
int dwc3_otg_init(struct dwc3 *dwc)
{
u32 reg;
int ret = 0;
struct dwc3_otg *dotg;
dev_dbg(dwc->dev, "dwc3_otg_init\n");
/*
* GHWPARAMS6[10] bit is SRPSupport.
* This bit also reflects DWC_USB3_EN_OTG
*/
reg = dwc3_readl(dwc->regs, DWC3_GHWPARAMS6);
if (!(reg & DWC3_GHWPARAMS6_SRP_SUPPORT)) {
/*
* No OTG support in the HW core.
* We return 0 to indicate no error, since this is acceptable
* situation, just continue probe the dwc3 driver without otg.
*/
dev_dbg(dwc->dev, "dwc3_otg address space is not supported\n");
return 0;
}
/* Allocate and init otg instance */
dotg = kzalloc(sizeof(struct dwc3_otg), GFP_KERNEL);
if (!dotg) {
dev_err(dwc->dev, "unable to allocate dwc3_otg\n");
return -ENOMEM;
}
/* DWC3 has separate IRQ line for OTG events (ID/BSV etc.) */
dotg->irq = platform_get_irq_byname(to_platform_device(dwc->dev),
"otg_irq");
if (dotg->irq < 0) {
dev_err(dwc->dev, "%s: missing OTG IRQ\n", __func__);
ret = -ENODEV;
goto err1;
}
dotg->regs = dwc->regs;
dotg->otg.set_peripheral = dwc3_otg_set_peripheral;
dotg->otg.set_host = dwc3_otg_set_host;
/* This reference is used by dwc3 modules for checking otg existance */
dwc->dotg = dotg;
dotg->otg.phy = kzalloc(sizeof(struct usb_phy), GFP_KERNEL);
if (!dotg->otg.phy) {
dev_err(dwc->dev, "unable to allocate dwc3_otg.phy\n");
ret = -ENOMEM;
goto err1;
}
dotg->dwc = dwc;
dotg->otg.phy->otg = &dotg->otg;
dotg->otg.phy->dev = dwc->dev;
dotg->otg.phy->set_power = dwc3_otg_set_power;
dotg->otg.phy->set_suspend = dwc3_otg_set_suspend;
ret = usb_set_transceiver(dotg->otg.phy);
if (ret) {
dev_err(dotg->otg.phy->dev,
"%s: failed to set transceiver, already exists\n",
__func__);
goto err2;
}
dotg->otg.phy->state = OTG_STATE_UNDEFINED;
init_completion(&dotg->dwc3_xcvr_vbus_init);
INIT_DELAYED_WORK(&dotg->sm_work, dwc3_otg_sm_work);
ret = request_irq(dotg->irq, dwc3_otg_interrupt, IRQF_SHARED,
"dwc3_otg", dotg);
if (ret) {
dev_err(dotg->otg.phy->dev, "failed to request irq #%d --> %d\n",
dotg->irq, ret);
goto err3;
}
pm_runtime_get(dwc->dev);
return 0;
err3:
cancel_delayed_work_sync(&dotg->sm_work);
usb_set_transceiver(NULL);
err2:
kfree(dotg->otg.phy);
err1:
dwc->dotg = NULL;
kfree(dotg);
return ret;
}
/**
* dwc3_otg_sm_work - workqueue function.
*
* @w: Pointer to the dwc3 otg workqueue
*
* NOTE: After any change in phy->state,
* we must reschdule the state machine.
*/
static void dwc3_otg_sm_work(struct work_struct *w)
{
struct dwc3_otg *dotg = container_of(w, struct dwc3_otg, sm_work.work);
struct usb_phy *phy = dotg->otg.phy;
struct dwc3_charger *charger = dotg->charger;
bool work = 0;
int ret = 0;
unsigned long delay = 0;
pm_runtime_resume(phy->dev);
dev_dbg(phy->dev, "%s state\n", otg_state_string(phy->state));
/* Check OTG state */
switch (phy->state) {
case OTG_STATE_UNDEFINED:
dwc3_otg_init_sm(dotg);
if (!dotg->psy) {
dotg->psy = power_supply_get_by_name("usb");
if (!dotg->psy)
dev_err(phy->dev,
"couldn't get usb power supply\n");
}
/* Switch to A or B-Device according to ID / BSV */
if (!test_bit(ID, &dotg->inputs)) {
dev_dbg(phy->dev, "!id\n");
phy->state = OTG_STATE_A_IDLE;
work = 1;
} else if (test_bit(B_SESS_VLD, &dotg->inputs)) {
dev_dbg(phy->dev, "b_sess_vld\n");
phy->state = OTG_STATE_B_IDLE;
work = 1;
} else {
phy->state = OTG_STATE_B_IDLE;
dev_dbg(phy->dev, "No device, trying to suspend\n");
pm_runtime_put_sync(phy->dev);
}
break;
case OTG_STATE_B_IDLE:
if (!test_bit(ID, &dotg->inputs)) {
dev_dbg(phy->dev, "!id\n");
phy->state = OTG_STATE_A_IDLE;
work = 1;
dotg->charger_retry_count = 0;
if (charger) {
if (charger->chg_type == DWC3_INVALID_CHARGER)
charger->start_detection(dotg->charger,
false);
else
charger->chg_type =
DWC3_INVALID_CHARGER;
}
} else if (test_bit(B_SESS_VLD, &dotg->inputs)) {
dev_dbg(phy->dev, "b_sess_vld\n");
if (charger) {
/* Has charger been detected? If no detect it */
switch (charger->chg_type) {
case DWC3_DCP_CHARGER:
case DWC3_PROPRIETARY_CHARGER:
dev_dbg(phy->dev, "lpm, DCP charger\n");
dwc3_otg_set_power(phy,
DWC3_IDEV_CHG_MAX);
pm_runtime_put_sync(phy->dev);
break;
case DWC3_CDP_CHARGER:
dwc3_otg_set_power(phy,
DWC3_IDEV_CHG_MAX);
dwc3_otg_start_peripheral(&dotg->otg,
1);
phy->state = OTG_STATE_B_PERIPHERAL;
work = 1;
break;
case DWC3_SDP_CHARGER:
dwc3_otg_start_peripheral(&dotg->otg,
1);
phy->state = OTG_STATE_B_PERIPHERAL;
work = 1;
/* OPPO 2013-10-05 wangjc Add begin for support non-standard charger, HW_VERSION__12 is dvt */
#ifdef CONFIG_MACH_MSM8974_14001
#if defined(CONFIG_OPPO_DEVICE_FIND7) || defined(CONFIG_OPPO_DEVICE_FIND7WX)
if(get_pcb_version() < HW_VERSION__12) {
cancel_delayed_work_sync(&dotg->non_standard_charger_work);
non_standard = true;
schedule_delayed_work(&dotg->non_standard_charger_work,
round_jiffies_relative(msecs_to_jiffies
(5000)));
} else {
/* [email protected], 2014/01/23 Add for notify usb online earlier */
power_supply_set_online(dotg->psy, true);
power_supply_changed(dotg->psy);
}
#else
power_supply_set_online(dotg->psy, true);
power_supply_changed(dotg->psy);
#endif
#endif
/* OPPO 2013-10-05 wangjc Add end */
break;
case DWC3_FLOATED_CHARGER:
/* OPPO 2013-10-05 wangjc Modify begin for support non-standard charger */
#ifndef CONFIG_MACH_MSM8974_14001
if (dotg->charger_retry_count <
max_chgr_retry_count)
dotg->charger_retry_count++;
/*
* In case of floating charger, if
* retry count equal to max retry count
* notify PMIC about floating charger
* and put Hw in low power mode. Else
* perform charger detection again by
* calling start_detection() with false
* and then with true argument.
*/
if (dotg->charger_retry_count ==
max_chgr_retry_count) {
dwc3_otg_set_power(phy, 0);
pm_runtime_put_sync(phy->dev);
break;
}
charger->start_detection(dotg->charger,
false);
#else
dev_dbg(phy->dev, "lpm, FLOATED charger\n");
dwc3_otg_set_power(phy,
DWC3_IDEV_CHG_FLOATED);
pm_runtime_put_sync(phy->dev);
break;
#endif
/* OPPO 2013-10-05 wangjc Modify end */
default:
dev_dbg(phy->dev, "chg_det started\n");
/* OPPO 2013-11-18 wangjc Modify begin for detect charger type later */
#ifndef CONFIG_MACH_MSM8974_14001
charger->start_detection(charger, true);
#else
/* [email protected], 2014/02/24 Add for solve usb reboot problem */
cancel_delayed_work_sync(&dotg->detect_work);
/* [email protected], 2014/03/25 Add for solve usb reboot problem,bug 422328 */
if (charger)
charger->start_detection(dotg->charger, false);
dotg->charger_retry_count = 0;
dwc3_otg_set_power(phy, 0);
queue_delayed_work(system_nrt_wq, &dotg->detect_work, msecs_to_jiffies(600));
#endif
/* OPPO 2013-11-18 wangjc Modify end */
break;
}
} else {
/* no charger registered, start peripheral */
if (dwc3_otg_start_peripheral(&dotg->otg, 1)) {
/*
* Probably set_peripheral not called
* yet. We will re-try as soon as it
* will be called
*/
dev_err(phy->dev, "enter lpm as\n"
"unable to start B-device\n");
phy->state = OTG_STATE_UNDEFINED;
pm_runtime_put_sync(phy->dev);
return;
}
}
} else {
/* OPPO 2013-12-01 wangjc Add begin for for non standard charger detect, HW_VERSION__12 is dvt */
#ifdef CONFIG_MACH_MSM8974_14001
//#ifdef CONFIG_OPPO_DEVICE_FIND7
#if defined(CONFIG_OPPO_DEVICE_FIND7) || defined(CONFIG_OPPO_DEVICE_FIND7WX)
if(get_pcb_version() < HW_VERSION__12) {
cancel_delayed_work_sync(&dotg->non_standard_charger_work);
}
#endif
#endif
/* OPPO 2013-12-01 wangjc Add end */
#ifdef CONFIG_MACH_MSM8974_14001
/* [email protected], 2014/01/06 Add for solve usb reboot problem */
cancel_delayed_work_sync(&dotg->detect_work);
#endif /*CONFIG_MACH_MSM8974_14001*/
if (charger)
charger->start_detection(dotg->charger, false);
dotg->charger_retry_count = 0;
dwc3_otg_set_power(phy, 0);
dev_dbg(phy->dev, "No device, trying to suspend\n");
pm_runtime_put_sync(phy->dev);
}
break;
case OTG_STATE_B_PERIPHERAL:
if (!test_bit(B_SESS_VLD, &dotg->inputs) ||
!test_bit(ID, &dotg->inputs)) {
dev_dbg(phy->dev, "!id || !bsv\n");
dwc3_otg_start_peripheral(&dotg->otg, 0);
phy->state = OTG_STATE_B_IDLE;
if (charger)
charger->chg_type = DWC3_INVALID_CHARGER;
work = 1;
}
break;
case OTG_STATE_A_IDLE:
/* Switch to A-Device*/
if (test_bit(ID, &dotg->inputs)) {
dev_dbg(phy->dev, "id\n");
phy->state = OTG_STATE_B_IDLE;
dotg->vbus_retry_count = 0;
work = 1;
} else {
phy->state = OTG_STATE_A_HOST;
ret = dwc3_otg_start_host(&dotg->otg, 1);
if ((ret == -EPROBE_DEFER) &&
dotg->vbus_retry_count < 3) {
/*
* Get regulator failed as regulator driver is
* not up yet. Will try to start host after 1sec
*/
phy->state = OTG_STATE_A_IDLE;
dev_dbg(phy->dev, "Unable to get vbus regulator. Retrying...\n");
delay = VBUS_REG_CHECK_DELAY;
work = 1;
dotg->vbus_retry_count++;
} else if (ret) {
/*
* Probably set_host was not called yet.
* We will re-try as soon as it will be called
*/
dev_dbg(phy->dev, "enter lpm as\n"
"unable to start A-device\n");
phy->state = OTG_STATE_A_IDLE;
pm_runtime_put_sync(phy->dev);
return;
}
}
break;
case OTG_STATE_A_HOST:
if (test_bit(ID, &dotg->inputs)) {
dev_dbg(phy->dev, "id\n");
dwc3_otg_start_host(&dotg->otg, 0);
phy->state = OTG_STATE_B_IDLE;
dotg->vbus_retry_count = 0;
work = 1;
}
break;
default:
dev_err(phy->dev, "%s: invalid otg-state\n", __func__);
}
if (work)
queue_delayed_work(system_nrt_wq, &dotg->sm_work, delay);
}
/**
* dwc3_otg_sm_work - workqueue function.
*
* @w: Pointer to the dwc3 otg workqueue
*
* NOTE: After any change in phy->state,
* we must reschdule the state machine.
*/
static void dwc3_otg_sm_work(struct work_struct *w)
{
struct dwc3_otg *dotg = container_of(w, struct dwc3_otg, sm_work);
struct usb_phy *phy = dotg->otg.phy;
struct dwc3_charger *charger = dotg->charger;
bool work = 0;
dev_dbg(phy->dev, "%s state\n", otg_state_string(phy->state));
/* Check OTG state */
switch (phy->state) {
case OTG_STATE_UNDEFINED:
dwc3_otg_init_sm(dotg);
/* Switch to A or B-Device according to ID / BSV */
if (!test_bit(ID, &dotg->inputs) && phy->otg->host) {
dev_dbg(phy->dev, "!id\n");
phy->state = OTG_STATE_A_IDLE;
work = 1;
} else if (test_bit(B_SESS_VLD, &dotg->inputs)) {
dev_dbg(phy->dev, "b_sess_vld\n");
phy->state = OTG_STATE_B_IDLE;
work = 1;
} else {
phy->state = OTG_STATE_B_IDLE;
/* TODO: Enter low power state */
}
break;
case OTG_STATE_B_IDLE:
if (!test_bit(ID, &dotg->inputs) && phy->otg->host) {
dev_dbg(phy->dev, "!id\n");
phy->state = OTG_STATE_A_IDLE;
work = 1;
if (charger) {
if (charger->chg_type == DWC3_INVALID_CHARGER)
charger->start_detection(dotg->charger,
false);
else
charger->chg_type =
DWC3_INVALID_CHARGER;
}
} else if (test_bit(B_SESS_VLD, &dotg->inputs)) {
dev_dbg(phy->dev, "b_sess_vld\n");
if (charger) {
/* Has charger been detected? If no detect it */
switch (charger->chg_type) {
case DWC3_DCP_CHARGER:
/* TODO: initiate LPM */
break;
case DWC3_CDP_CHARGER:
dwc3_otg_start_peripheral(&dotg->otg,
1);
phy->state = OTG_STATE_B_PERIPHERAL;
work = 1;
break;
case DWC3_SDP_CHARGER:
dwc3_otg_start_peripheral(&dotg->otg,
1);
phy->state = OTG_STATE_B_PERIPHERAL;
work = 1;
break;
default:
dev_dbg(phy->dev, "chg_det started\n");
charger->start_detection(charger, true);
break;
}
} else {
/* no charger registered, start peripheral */
if (dwc3_otg_start_peripheral(&dotg->otg, 1)) {
/*
* Probably set_peripheral not called
* yet. We will re-try as soon as it
* will be called
*/
dev_err(phy->dev,
"unable to start B-device\n");
phy->state = OTG_STATE_UNDEFINED;
return;
}
}
} else {
if (charger) {
if (charger->chg_type == DWC3_INVALID_CHARGER)
charger->start_detection(dotg->charger,
false);
else
charger->chg_type =
DWC3_INVALID_CHARGER;
}
/* TODO: Enter low power state */
}
break;
case OTG_STATE_B_PERIPHERAL:
if (!test_bit(B_SESS_VLD, &dotg->inputs) ||
!test_bit(ID, &dotg->inputs)) {
dev_dbg(phy->dev, "!id || !bsv\n");
dwc3_otg_start_peripheral(&dotg->otg, 0);
phy->state = OTG_STATE_B_IDLE;
if (charger)
charger->chg_type = DWC3_INVALID_CHARGER;
work = 1;
}
break;
case OTG_STATE_A_IDLE:
/* Switch to A-Device*/
if (test_bit(ID, &dotg->inputs)) {
dev_dbg(phy->dev, "id\n");
phy->state = OTG_STATE_B_IDLE;
work = 1;
} else {
if (dwc3_otg_start_host(&dotg->otg, 1)) {
/*
* Probably set_host was not called yet.
* We will re-try as soon as it will be called
*/
dev_dbg(phy->dev,
"unable to start A-device\n");
phy->state = OTG_STATE_UNDEFINED;
return;
}
phy->state = OTG_STATE_A_HOST;
}
break;
case OTG_STATE_A_HOST:
if (test_bit(ID, &dotg->inputs)) {
dev_dbg(phy->dev, "id\n");
dwc3_otg_start_host(&dotg->otg, 0);
phy->state = OTG_STATE_B_IDLE;
work = 1;
}
break;
default:
dev_err(phy->dev, "%s: invalid otg-state\n", __func__);
}
if (work)
schedule_work(&dotg->sm_work);
}
/**
* dwc3_otg_sm_work - workqueue function.
*
* @w: Pointer to the dwc3 otg workqueue
*
* NOTE: After any change in phy->state,
* we must reschdule the state machine.
*/
static void dwc3_otg_sm_work(struct work_struct *w)
{
struct dwc3_otg *dotg = container_of(w, struct dwc3_otg, sm_work.work);
struct usb_phy *phy = dotg->otg.phy;
struct dwc3_charger *charger = dotg->charger;
bool work = 0;
int ret = 0;
unsigned long delay = 0;
pm_runtime_resume(phy->dev);
dev_dbg(phy->dev, "%s state\n", usb_otg_state_string(phy->state));
/* Check OTG state */
switch (phy->state) {
case OTG_STATE_UNDEFINED:
dwc3_otg_init_sm(dotg);
if (!dotg->psy) {
dotg->psy = power_supply_get_by_name("usb");
if (!dotg->psy)
dev_err(phy->dev,
"couldn't get usb power supply\n");
}
/* Switch to A or B-Device according to ID / BSV */
if (!test_bit(ID, &dotg->inputs)) {
dev_dbg(phy->dev, "!id\n");
phy->state = OTG_STATE_A_IDLE;
work = 1;
} else if (test_bit(B_SESS_VLD, &dotg->inputs)) {
dev_dbg(phy->dev, "b_sess_vld\n");
phy->state = OTG_STATE_B_IDLE;
work = 1;
} else {
phy->state = OTG_STATE_B_IDLE;
dev_dbg(phy->dev, "No device, trying to suspend\n");
dbg_event(0xFF, "UNDEF put", 0);
pm_runtime_put_sync(phy->dev);
}
break;
case OTG_STATE_B_IDLE:
if (!test_bit(ID, &dotg->inputs)) {
dev_dbg(phy->dev, "!id\n");
phy->state = OTG_STATE_A_IDLE;
work = 1;
dotg->charger_retry_count = 0;
if (charger) {
if (charger->chg_type == DWC3_INVALID_CHARGER)
charger->start_detection(dotg->charger,
false);
else
charger->chg_type =
DWC3_INVALID_CHARGER;
}
dwc3_otg_set_power(phy, 0);
} else if (test_bit(B_SESS_VLD, &dotg->inputs)) {
dev_dbg(phy->dev, "b_sess_vld\n");
if (charger) {
/* Has charger been detected? If no detect it */
switch (charger->chg_type) {
case DWC3_DCP_CHARGER:
case DWC3_PROPRIETARY_CHARGER:
dev_dbg(phy->dev, "lpm, DCP charger\n");
dwc3_otg_set_power(phy,
dcp_max_current);
dbg_event(0xFF, "PROPCHG put", 0);
pm_runtime_put_sync(phy->dev);
break;
case DWC3_PROPRIETARY_1000MA:
dev_dbg(phy->dev, "lpm, DCP charger\n");
dwc3_otg_set_power(phy,
DWC3_1000MA_CHG_MAX);
pm_runtime_put_sync(phy->dev);
break;
case DWC3_PROPRIETARY_500MA:
dev_dbg(phy->dev, "lpm, DCP charger\n");
dwc3_otg_set_power(phy,
DWC3_500MA_CHG_MAX);
pm_runtime_put_sync(phy->dev);
break;
case DWC3_CDP_CHARGER:
dwc3_otg_set_power(phy,
DWC3_IDEV_CHG_MAX);
dwc3_otg_start_peripheral(&dotg->otg,
1);
phy->state = OTG_STATE_B_PERIPHERAL;
work = 1;
break;
case DWC3_SDP_CHARGER:
dwc3_otg_start_peripheral(&dotg->otg,
1);
phy->state = OTG_STATE_B_PERIPHERAL;
work = 1;
break;
case DWC3_FLOATED_CHARGER:
if (dotg->charger_retry_count <
max_chgr_retry_count)
dotg->charger_retry_count++;
/*
* In case of floating charger, if
* retry count equal to max retry count
* notify PMIC about floating charger
* and put Hw in low power mode. Else
* perform charger detection again by
* calling start_detection() with false
* and then with true argument.
*/
if (dotg->charger_retry_count ==
max_chgr_retry_count) {
dwc3_otg_set_power(phy, 0);
dwc3_otg_set_invalid_charger(phy);
dbg_event(0xFF, "FLCHG put", 0);
pm_runtime_put_sync(phy->dev);
break;
}
charger->start_detection(dotg->charger,
false);
delay = msecs_to_jiffies(100 *
dotg->charger_retry_count);
work = 1;
break;
default:
dev_dbg(phy->dev, "chg_det started\n");
charger->start_detection(charger, true);
break;
}
} else {
/*
* no charger registered, assuming SDP
* and start peripheral
*/
phy->state = OTG_STATE_B_PERIPHERAL;
if (dwc3_otg_start_peripheral(&dotg->otg, 1)) {
/*
* Probably set_peripheral not called
* yet. We will re-try as soon as it
* will be called
*/
dev_err(phy->dev, "enter lpm as\n"
"unable to start B-device\n");
phy->state = OTG_STATE_UNDEFINED;
dbg_event(0xFF, "NoCH put", 0);
pm_runtime_put_sync(phy->dev);
return;
}
}
} else {
if (charger)
charger->start_detection(dotg->charger, false);
dotg->charger_retry_count = 0;
dwc3_otg_set_power(phy, 0);
dev_dbg(phy->dev, "No device, trying to suspend\n");
dbg_event(0xFF, "NoDev put", 0);
pm_runtime_put_sync(phy->dev);
}
break;
case OTG_STATE_B_PERIPHERAL:
if (!test_bit(B_SESS_VLD, &dotg->inputs) ||
!test_bit(ID, &dotg->inputs)) {
dev_dbg(phy->dev, "!id || !bsv\n");
dwc3_otg_start_peripheral(&dotg->otg, 0);
phy->state = OTG_STATE_B_IDLE;
if (charger)
charger->chg_type = DWC3_INVALID_CHARGER;
work = 1;
} else if (test_bit(DWC3_OTG_SUSPEND, &dotg->inputs) &&
test_bit(B_SESS_VLD, &dotg->inputs)) {
dbg_event(0xFF, "BPER put", 0);
pm_runtime_put_sync(phy->dev);
}
break;
case OTG_STATE_A_IDLE:
/* Switch to A-Device*/
if (test_bit(ID, &dotg->inputs)) {
dev_dbg(phy->dev, "id\n");
phy->state = OTG_STATE_B_IDLE;
dotg->vbus_retry_count = 0;
work = 1;
clear_bit(A_VBUS_DROP_DET, &dotg->inputs);
#ifdef CONFIG_USB_HOST_EXTRA_NOTIFICATION
host_send_uevent(USB_HOST_EXT_EVENT_NONE);
#endif
} else if (test_bit(A_VBUS_DROP_DET, &dotg->inputs)) {
dev_dbg(phy->dev, "vbus_drop_det\n");
/* staying on here until exit from A-Device */
} else {
phy->state = OTG_STATE_A_HOST;
ret = dwc3_otg_start_host(&dotg->otg, 1);
if ((ret == -EPROBE_DEFER) &&
dotg->vbus_retry_count < 3) {
/*
* Get regulator failed as regulator driver is
* not up yet. Will try to start host after 1sec
*/
phy->state = OTG_STATE_A_IDLE;
dev_dbg(phy->dev, "Unable to get vbus regulator. Retrying...\n");
delay = VBUS_REG_CHECK_DELAY;
work = 1;
dotg->vbus_retry_count++;
} else if (ret) {
dev_dbg(phy->dev, "enter lpm as\n"
"unable to start A-device\n");
phy->state = OTG_STATE_A_IDLE;
dbg_event(0xFF, "AIDL put", 0);
pm_runtime_put_sync(phy->dev);
return;
} else {
/*
* delay 1s to allow for xHCI to detect
* just-attached devices before allowing
* runtime suspend
*/
dev_dbg(phy->dev, "a_host state entered\n");
delay = VBUS_REG_CHECK_DELAY;
work = 1;
}
}
break;
case OTG_STATE_A_HOST:
if (test_bit(ID, &dotg->inputs)) {
dev_dbg(phy->dev, "id\n");
dwc3_otg_start_host(&dotg->otg, 0);
phy->state = OTG_STATE_B_IDLE;
dotg->vbus_retry_count = 0;
work = 1;
clear_bit(A_VBUS_DROP_DET, &dotg->inputs);
#ifdef CONFIG_USB_HOST_EXTRA_NOTIFICATION
host_send_uevent(USB_HOST_EXT_EVENT_NONE);
#endif
} else if (test_bit(A_VBUS_DROP_DET, &dotg->inputs)) {
dev_dbg(phy->dev, "vbus_drop_det\n");
dwc3_otg_start_host(&dotg->otg, 0);
phy->state = OTG_STATE_A_IDLE;
work = 1;
#ifdef CONFIG_USB_HOST_EXTRA_NOTIFICATION
host_send_uevent(USB_HOST_EXT_EVENT_VBUS_DROP);
#endif
} else {
dev_dbg(phy->dev, "still in a_host state. Resuming root hub.\n");
dbg_event(0xFF, "AHOST put", 0);
pm_runtime_resume(&dotg->dwc->xhci->dev);
pm_runtime_put_noidle(phy->dev);
}
break;
default:
dev_err(phy->dev, "%s: invalid otg-state\n", __func__);
}
if (work)
queue_delayed_work(system_nrt_wq, &dotg->sm_work, delay);
}