Ejemplos de e1000_setup_init_funcs en C++ (Cpp)

Ejemplo n.º 1

Archivo: e1000_main.c Proyecto: lyu571/xcat-dep

/**
 * e1000_sw_init - Initialize general software structures (struct e1000_adapter)
 * @adapter: board private structure to initialize
 *
 * e1000_sw_init initializes the Adapter private data structure.
 * Fields are initialized based on PCI device information and
 * OS network device settings (MTU size).
 **/
static int e1000_sw_init(struct e1000_adapter *adapter)
{
	struct e1000_hw *hw = &adapter->hw;
	struct pci_device  *pdev = adapter->pdev;

	/* PCI config space info */

	hw->vendor_id = pdev->vendor;
	hw->device_id = pdev->device;

	pci_read_config_word(pdev, PCI_SUBSYSTEM_VENDOR_ID, &hw->subsystem_vendor_id);
	pci_read_config_word(pdev, PCI_SUBSYSTEM_ID, &hw->subsystem_device_id);

	pci_read_config_byte(pdev, PCI_REVISION_ID, &hw->revision_id);

	pci_read_config_word(pdev, PCI_COMMAND, &hw->bus.pci_cmd_word);

	adapter->rx_buffer_len = MAXIMUM_ETHERNET_VLAN_SIZE;
	adapter->max_frame_size = MAXIMUM_ETHERNET_VLAN_SIZE +
                                  ETH_HLEN + ETH_FCS_LEN;
	adapter->min_frame_size = ETH_ZLEN + ETH_FCS_LEN;

	hw->fc.requested_mode = e1000_fc_none;

	/* Initialize the hardware-specific values */
	if (e1000_setup_init_funcs(hw, false)) {
		DBG ("Hardware Initialization Failure\n");
		return -EIO;
	}

	/* Explicitly disable IRQ since the NIC can be in any state. */
	e1000_irq_disable ( adapter );

	return 0;
}

Ejemplo n.º 2

static int
eth_em_dev_init(struct rte_eth_dev *eth_dev)
{
	struct rte_pci_device *pci_dev;
	struct e1000_adapter *adapter =
		E1000_DEV_PRIVATE(eth_dev->data->dev_private);
	struct e1000_hw *hw =
		E1000_DEV_PRIVATE_TO_HW(eth_dev->data->dev_private);
	struct e1000_vfta * shadow_vfta =
		E1000_DEV_PRIVATE_TO_VFTA(eth_dev->data->dev_private);

	pci_dev = eth_dev->pci_dev;

	eth_dev->dev_ops = &eth_em_ops;
	eth_dev->rx_pkt_burst = (eth_rx_burst_t)&eth_em_recv_pkts;
	eth_dev->tx_pkt_burst = (eth_tx_burst_t)&eth_em_xmit_pkts;

	/* for secondary processes, we don't initialise any further as primary
	 * has already done this work. Only check we don't need a different
	 * RX function */
	if (rte_eal_process_type() != RTE_PROC_PRIMARY){
		if (eth_dev->data->scattered_rx)
			eth_dev->rx_pkt_burst =
				(eth_rx_burst_t)&eth_em_recv_scattered_pkts;
		return 0;
	}

	rte_eth_copy_pci_info(eth_dev, pci_dev);

	hw->hw_addr = (void *)pci_dev->mem_resource[0].addr;
	hw->device_id = pci_dev->id.device_id;
	adapter->stopped = 0;

	/* For ICH8 support we'll need to map the flash memory BAR */

	if (e1000_setup_init_funcs(hw, TRUE) != E1000_SUCCESS ||
			em_hw_init(hw) != 0) {
		PMD_INIT_LOG(ERR, "port_id %d vendorID=0x%x deviceID=0x%x: "
			"failed to init HW",
			eth_dev->data->port_id, pci_dev->id.vendor_id,
			pci_dev->id.device_id);
		return -(ENODEV);
	}

	/* Allocate memory for storing MAC addresses */
	eth_dev->data->mac_addrs = rte_zmalloc("e1000", ETHER_ADDR_LEN *
			hw->mac.rar_entry_count, 0);
	if (eth_dev->data->mac_addrs == NULL) {
		PMD_INIT_LOG(ERR, "Failed to allocate %d bytes needed to "
			"store MAC addresses",
			ETHER_ADDR_LEN * hw->mac.rar_entry_count);
		return -(ENOMEM);
	}

	/* Copy the permanent MAC address */
	ether_addr_copy((struct ether_addr *) hw->mac.addr,
		eth_dev->data->mac_addrs);

	/* initialize the vfta */
	memset(shadow_vfta, 0, sizeof(*shadow_vfta));

	PMD_INIT_LOG(DEBUG, "port_id %d vendorID=0x%x deviceID=0x%x",
		     eth_dev->data->port_id, pci_dev->id.vendor_id,
		     pci_dev->id.device_id);

	rte_intr_callback_register(&(pci_dev->intr_handle),
		eth_em_interrupt_handler, (void *)eth_dev);

	return (0);
}