void DisablePhyComa(struct et131x_adapter *etdev)
{
u32 GlobalPmCSR;
GlobalPmCSR = readl(&etdev->regs->global.pm_csr);
GlobalPmCSR |= ET_PMCSR_INIT;
GlobalPmCSR &= ~ET_PM_PHY_SW_COMA;
writel(GlobalPmCSR, &etdev->regs->global.pm_csr);
etdev->AiForceSpeed = etdev->PoMgmt.PowerDownSpeed;
etdev->AiForceDpx = etdev->PoMgmt.PowerDownDuplex;
et131x_init_send(etdev);
et131x_reset_recv(etdev);
et131x_soft_reset(etdev);
et131x_adapter_setup(etdev);
etdev->Flags &= ~fMP_ADAPTER_LOWER_POWER;
et131x_rx_dma_enable(etdev);
}
/**
* et131x_change_mtu - The handler called to change the MTU for the device
* @netdev: device whose MTU is to be changed
* @new_mtu: the desired MTU
*
* Returns 0 on success, errno on failure (as defined in errno.h)
*/
int et131x_change_mtu(struct net_device *netdev, int new_mtu)
{
int result = 0;
struct et131x_adapter *adapter = netdev_priv(netdev);
/* Make sure the requested MTU is valid */
if (new_mtu < 64 || new_mtu > 9216)
return -EINVAL;
/* Stop the netif queue */
netif_stop_queue(netdev);
/* Stop the Tx and Rx DMA engines */
et131x_rx_dma_disable(adapter);
et131x_tx_dma_disable(adapter);
/* Disable device interrupts */
et131x_disable_interrupts(adapter);
et131x_handle_send_interrupt(adapter);
et131x_handle_recv_interrupt(adapter);
/* Set the new MTU */
netdev->mtu = new_mtu;
/* Free Rx DMA memory */
et131x_adapter_memory_free(adapter);
/* Set the config parameter for Jumbo Packet support */
adapter->RegistryJumboPacket = new_mtu + 14;
et131x_soft_reset(adapter);
/* Alloc and init Rx DMA memory */
result = et131x_adapter_memory_alloc(adapter);
if (result != 0) {
dev_warn(&adapter->pdev->dev,
"Change MTU failed; couldn't re-alloc DMA memory\n");
return result;
}
et131x_init_send(adapter);
et131x_hwaddr_init(adapter);
memcpy(netdev->dev_addr, adapter->CurrentAddress, ETH_ALEN);
/* Init the device with the new settings */
et131x_adapter_setup(adapter);
/* Enable interrupts */
if (adapter->Flags & fMP_ADAPTER_INTERRUPT_IN_USE)
et131x_enable_interrupts(adapter);
/* Restart the Tx and Rx DMA engines */
et131x_rx_dma_enable(adapter);
et131x_tx_dma_enable(adapter);
/* Restart the netif queue */
netif_wake_queue(netdev);
return result;
}
/**
* DisablePhyComa - Disable the Phy Coma Mode
* @pAdapter: pointer to our adapter structure
*/
void DisablePhyComa(struct et131x_adapter *pAdapter)
{
PM_CSR_t GlobalPmCSR;
DBG_ENTER(et131x_dbginfo);
GlobalPmCSR.value = readl(&pAdapter->CSRAddress->global.pm_csr.value);
/* Disable phy_sw_coma register and re-enable JAGCore clocks */
GlobalPmCSR.bits.pm_sysclk_gate = 1;
GlobalPmCSR.bits.pm_txclk_gate = 1;
GlobalPmCSR.bits.pm_rxclk_gate = 1;
GlobalPmCSR.bits.pm_phy_sw_coma = 0;
writel(GlobalPmCSR.value, &pAdapter->CSRAddress->global.pm_csr.value);
/* Restore the GbE PHY speed and duplex modes;
* Reset JAGCore; re-configure and initialize JAGCore and gigE PHY
*/
pAdapter->AiForceSpeed = pAdapter->PoMgmt.PowerDownSpeed;
pAdapter->AiForceDpx = pAdapter->PoMgmt.PowerDownDuplex;
/* Re-initialize the send structures */
et131x_init_send(pAdapter);
/* Reset the RFD list and re-start RU */
et131x_reset_recv(pAdapter);
/* Bring the device back to the state it was during init prior to
* autonegotiation being complete. This way, when we get the auto-neg
* complete interrupt, we can complete init by calling ConfigMacREGS2.
*/
et131x_soft_reset(pAdapter);
/* setup et1310 as per the documentation ?? */
et131x_adapter_setup(pAdapter);
/* Allow Tx to restart */
MP_CLEAR_FLAG(pAdapter, fMP_ADAPTER_LOWER_POWER);
/* Need to re-enable Rx. */
et131x_rx_dma_enable(pAdapter);
DBG_LEAVE(et131x_dbginfo);
}
/**
* et131x_set_mac_addr - handler to change the MAC address for the device
* @netdev: device whose MAC is to be changed
* @new_mac: the desired MAC address
*
* Returns 0 on success, errno on failure (as defined in errno.h)
*
* IMPLEMENTED BY : blux http://berndlux.de 22.01.2007 21:14
*/
int et131x_set_mac_addr(struct net_device *netdev, void *new_mac)
{
int result = 0;
struct et131x_adapter *adapter = netdev_priv(netdev);
struct sockaddr *address = new_mac;
/* begin blux */
if (adapter == NULL)
return -ENODEV;
/* Make sure the requested MAC is valid */
if (!is_valid_ether_addr(address->sa_data))
return -EINVAL;
/* Stop the netif queue */
netif_stop_queue(netdev);
/* Stop the Tx and Rx DMA engines */
et131x_rx_dma_disable(adapter);
et131x_tx_dma_disable(adapter);
/* Disable device interrupts */
et131x_disable_interrupts(adapter);
et131x_handle_send_interrupt(adapter);
et131x_handle_recv_interrupt(adapter);
/* Set the new MAC */
/* netdev->set_mac_address = &new_mac; */
/* netdev->mtu = new_mtu; */
memcpy(netdev->dev_addr, address->sa_data, netdev->addr_len);
printk(KERN_INFO "%s: Setting MAC address to %pM\n",
netdev->name, netdev->dev_addr);
/* Free Rx DMA memory */
et131x_adapter_memory_free(adapter);
/* Set the config parameter for Jumbo Packet support */
/* adapter->RegistryJumboPacket = new_mtu + 14; */
/* blux: not needet here, we'll change the MAC */
et131x_soft_reset(adapter);
/* Alloc and init Rx DMA memory */
result = et131x_adapter_memory_alloc(adapter);
if (result != 0) {
dev_err(&adapter->pdev->dev,
"Change MAC failed; couldn't re-alloc DMA memory\n");
return result;
}
et131x_init_send(adapter);
et131x_hwaddr_init(adapter);
/* Init the device with the new settings */
et131x_adapter_setup(adapter);
/* Enable interrupts */
if (adapter->Flags & fMP_ADAPTER_INTERRUPT_IN_USE)
et131x_enable_interrupts(adapter);
/* Restart the Tx and Rx DMA engines */
et131x_rx_dma_enable(adapter);
et131x_tx_dma_enable(adapter);
/* Restart the netif queue */
netif_wake_queue(netdev);
return result;
}
static int __devinit et131x_pci_setup(struct pci_dev *pdev,
const struct pci_device_id *ent)
{
int result = -EBUSY;
int pm_cap;
bool pci_using_dac;
struct net_device *netdev;
struct et131x_adapter *adapter;
/* Enable the device via the PCI subsystem */
if (pci_enable_device(pdev) != 0) {
dev_err(&pdev->dev,
"pci_enable_device() failed\n");
return -EIO;
}
/* Perform some basic PCI checks */
if (!(pci_resource_flags(pdev, 0) & IORESOURCE_MEM)) {
dev_err(&pdev->dev,
"Can't find PCI device's base address\n");
goto err_disable;
}
if (pci_request_regions(pdev, DRIVER_NAME)) {
dev_err(&pdev->dev,
"Can't get PCI resources\n");
goto err_disable;
}
/* Enable PCI bus mastering */
pci_set_master(pdev);
/* Query PCI for Power Mgmt Capabilities
*
* NOTE: Now reading PowerMgmt in another location; is this still
* needed?
*/
pm_cap = pci_find_capability(pdev, PCI_CAP_ID_PM);
if (pm_cap == 0) {
dev_err(&pdev->dev,
"Cannot find Power Management capabilities\n");
result = -EIO;
goto err_release_res;
}
/* Check the DMA addressing support of this device */
if (!pci_set_dma_mask(pdev, DMA_BIT_MASK(64))) {
pci_using_dac = true;
result = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(64));
if (result != 0) {
dev_err(&pdev->dev,
"Unable to obtain 64 bit DMA for consistent allocations\n");
goto err_release_res;
}
} else if (!pci_set_dma_mask(pdev, DMA_BIT_MASK(32))) {
pci_using_dac = false;
} else {
dev_err(&pdev->dev,
"No usable DMA addressing method\n");
result = -EIO;
goto err_release_res;
}
/* Allocate netdev and private adapter structs */
netdev = et131x_device_alloc();
if (netdev == NULL) {
dev_err(&pdev->dev, "Couldn't alloc netdev struct\n");
result = -ENOMEM;
goto err_release_res;
}
adapter = et131x_adapter_init(netdev, pdev);
/* Initialise the PCI setup for the device */
et131x_pci_init(adapter, pdev);
/* Map the bus-relative registers to system virtual memory */
adapter->regs = pci_ioremap_bar(pdev, 0);
if (adapter->regs == NULL) {
dev_err(&pdev->dev, "Cannot map device registers\n");
result = -ENOMEM;
goto err_free_dev;
}
/* If Phy COMA mode was enabled when we went down, disable it here. */
writel(ET_PMCSR_INIT, &adapter->regs->global.pm_csr);
/* Issue a global reset to the et1310 */
et131x_soft_reset(adapter);
/* Disable all interrupts (paranoid) */
et131x_disable_interrupts(adapter);
/* Allocate DMA memory */
result = et131x_adapter_memory_alloc(adapter);
if (result != 0) {
dev_err(&pdev->dev, "Could not alloc adapater memory (DMA)\n");
goto err_iounmap;
}
/* Init send data structures */
et131x_init_send(adapter);
/*
* Set up the task structure for the ISR's deferred handler
*/
INIT_WORK(&adapter->task, et131x_isr_handler);
/* Copy address into the net_device struct */
memcpy(netdev->dev_addr, adapter->addr, ETH_ALEN);
/* Setup et1310 as per the documentation */
et131x_adapter_setup(adapter);
/* Create a timer to count errors received by the NIC */
init_timer(&adapter->ErrorTimer);
adapter->ErrorTimer.expires = jiffies + TX_ERROR_PERIOD * HZ / 1000;
adapter->ErrorTimer.function = et131x_error_timer_handler;
adapter->ErrorTimer.data = (unsigned long)adapter;
/* Initialize link state */
et131x_link_detection_handler((unsigned long)adapter);
/* Initialize variable for counting how long we do not have
link status */
adapter->boot_coma = 0;
/* We can enable interrupts now
*
* NOTE - Because registration of interrupt handler is done in the
* device's open(), defer enabling device interrupts to that
* point
*/
/* Register the net_device struct with the Linux network layer */
result = register_netdev(netdev);
if (result != 0) {
dev_err(&pdev->dev, "register_netdev() failed\n");
goto err_mem_free;
}
/* Register the net_device struct with the PCI subsystem. Save a copy
* of the PCI config space for this device now that the device has
* been initialized, just in case it needs to be quickly restored.
*/
pci_set_drvdata(pdev, netdev);
pci_save_state(adapter->pdev);
return result;
err_mem_free:
et131x_adapter_memory_free(adapter);
err_iounmap:
iounmap(adapter->regs);
err_free_dev:
pci_dev_put(pdev);
free_netdev(netdev);
err_release_res:
pci_release_regions(pdev);
err_disable:
pci_disable_device(pdev);
return result;
}
void et131x_Mii_check(struct et131x_adapter *etdev,
MI_BMSR_t bmsr, MI_BMSR_t bmsr_ints)
{
uint8_t link_status;
uint32_t autoneg_status;
uint32_t speed;
uint32_t duplex;
uint32_t mdi_mdix;
uint32_t masterslave;
uint32_t polarity;
unsigned long flags;
if (bmsr_ints.bits.link_status) {
if (bmsr.bits.link_status) {
etdev->PoMgmt.TransPhyComaModeOnBoot = 20;
spin_lock_irqsave(&etdev->Lock, flags);
etdev->MediaState = NETIF_STATUS_MEDIA_CONNECT;
etdev->Flags &= ~fMP_ADAPTER_LINK_DETECTION;
spin_unlock_irqrestore(&etdev->Lock, flags);
if (etdev->RegistryPhyLoopbk == false)
netif_carrier_on(etdev->netdev);
} else {
dev_warn(&etdev->pdev->dev,
"Link down - cable problem ?\n");
if (etdev->linkspeed == TRUEPHY_SPEED_10MBPS) {
uint16_t Register18;
MiRead(etdev, 0x12, &Register18);
MiWrite(etdev, 0x12, Register18 | 0x4);
MiWrite(etdev, 0x10, Register18 | 0x8402);
MiWrite(etdev, 0x11, Register18 | 511);
MiWrite(etdev, 0x12, Register18);
}
if (!(etdev->Flags & fMP_ADAPTER_LINK_DETECTION) ||
(etdev->MediaState == NETIF_STATUS_MEDIA_DISCONNECT)) {
spin_lock_irqsave(&etdev->Lock, flags);
etdev->MediaState =
NETIF_STATUS_MEDIA_DISCONNECT;
spin_unlock_irqrestore(&etdev->Lock,
flags);
if (etdev->RegistryPhyLoopbk == false)
netif_carrier_off(etdev->netdev);
}
etdev->linkspeed = 0;
etdev->duplex_mode = 0;
et131x_free_busy_send_packets(etdev);
et131x_init_send(etdev);
et131x_reset_recv(etdev);
et131x_soft_reset(etdev);
et131x_adapter_setup(etdev);
if (etdev->RegistryPhyComa == 1)
EnablePhyComa(etdev);
}
}
if (bmsr_ints.bits.auto_neg_complete ||
(etdev->AiForceDpx == 3 && bmsr_ints.bits.link_status)) {
if (bmsr.bits.auto_neg_complete || etdev->AiForceDpx == 3) {
ET1310_PhyLinkStatus(etdev,
&link_status, &autoneg_status,
&speed, &duplex, &mdi_mdix,
&masterslave, &polarity);
etdev->linkspeed = speed;
etdev->duplex_mode = duplex;
etdev->PoMgmt.TransPhyComaModeOnBoot = 20;
if (etdev->linkspeed == TRUEPHY_SPEED_10MBPS) {
uint16_t Register18;
MiRead(etdev, 0x12, &Register18);
MiWrite(etdev, 0x12, Register18 | 0x4);
MiWrite(etdev, 0x10, Register18 | 0x8402);
MiWrite(etdev, 0x11, Register18 | 511);
MiWrite(etdev, 0x12, Register18);
}
ConfigFlowControl(etdev);
if (etdev->linkspeed == TRUEPHY_SPEED_1000MBPS &&
etdev->RegistryJumboPacket > 2048)
ET1310_PhyAndOrReg(etdev, 0x16, 0xcfff,
0x2000);
SetRxDmaTimer(etdev);
ConfigMACRegs2(etdev);
}
}
}
/**
* et131x_set_mac_addr - handler to change the MAC address for the device
* @netdev: device whose MAC is to be changed
* @new_mac: the desired MAC address
*
* Returns 0 on success, errno on failure (as defined in errno.h)
*
* IMPLEMENTED BY : blux http://berndlux.de 22.01.2007 21:14
*/
int et131x_set_mac_addr(struct net_device *netdev, void *new_mac)
{
int result = 0;
struct et131x_adapter *adapter = netdev_priv(netdev);
struct sockaddr *address = new_mac;
DBG_ENTER(et131x_dbginfo);
// begin blux
// DBG_VERBOSE( et131x_dbginfo, "Function not implemented!!\n" );
if (adapter == NULL) {
DBG_LEAVE(et131x_dbginfo);
return -ENODEV;
}
/* Make sure the requested MAC is valid */
if (!is_valid_ether_addr(address->sa_data)) {
DBG_LEAVE(et131x_dbginfo);
return -EINVAL;
}
/* Stop the netif queue */
netif_stop_queue(netdev);
/* Stop the Tx and Rx DMA engines */
et131x_rx_dma_disable(adapter);
et131x_tx_dma_disable(adapter);
/* Disable device interrupts */
et131x_disable_interrupts(adapter);
et131x_handle_send_interrupt(adapter);
et131x_handle_recv_interrupt(adapter);
/* Set the new MAC */
// netdev->set_mac_address = &new_mac;
// netdev->mtu = new_mtu;
memcpy(netdev->dev_addr, address->sa_data, netdev->addr_len);
printk("%s: Setting MAC address to %02x:%02x:%02x:%02x:%02x:%02x\n",
netdev->name, netdev->dev_addr[0], netdev->dev_addr[1],
netdev->dev_addr[2], netdev->dev_addr[3], netdev->dev_addr[4],
netdev->dev_addr[5]);
/* Free Rx DMA memory */
et131x_adapter_memory_free(adapter);
/* Set the config parameter for Jumbo Packet support */
// adapter->RegistryJumboPacket = new_mtu + 14;
// blux: not needet here, w'll change the MAC
et131x_soft_reset(adapter);
/* Alloc and init Rx DMA memory */
result = et131x_adapter_memory_alloc(adapter);
if (result != 0) {
DBG_WARNING(et131x_dbginfo,
"Change MAC failed; couldn't re-alloc DMA memory\n");
return result;
}
et131x_init_send(adapter);
et131x_setup_hardware_properties(adapter);
// memcpy( netdev->dev_addr, adapter->CurrentAddress, ETH_ALEN );
// blux: no, do not override our nice address
/* Init the device with the new settings */
et131x_adapter_setup(adapter);
/* Enable interrupts */
if (MP_TEST_FLAG(adapter, fMP_ADAPTER_INTERRUPT_IN_USE)) {
et131x_enable_interrupts(adapter);
}
/* Restart the Tx and Rx DMA engines */
et131x_rx_dma_enable(adapter);
et131x_tx_dma_enable(adapter);
/* Restart the netif queue */
netif_wake_queue(netdev);
DBG_LEAVE(et131x_dbginfo);
return result;
}
int __devinit et131x_pci_setup(struct pci_dev *pdev,
const struct pci_device_id *ent)
{
int result = 0;
int pm_cap;
bool pci_using_dac;
struct net_device *netdev = NULL;
struct et131x_adapter *adapter = NULL;
/* Enable the device via the PCI subsystem */
result = pci_enable_device(pdev);
if (result != 0) {
dev_err(&adapter->pdev->dev,
"pci_enable_device() failed\n");
goto out;
}
/* Perform some basic PCI checks */
if (!(pci_resource_flags(pdev, 0) & IORESOURCE_MEM)) {
dev_err(&adapter->pdev->dev,
"Can't find PCI device's base address\n");
result = -ENODEV;
goto out;
}
result = pci_request_regions(pdev, DRIVER_NAME);
if (result != 0) {
dev_err(&adapter->pdev->dev,
"Can't get PCI resources\n");
goto err_disable;
}
/* Enable PCI bus mastering */
pci_set_master(pdev);
/* Query PCI for Power Mgmt Capabilities
*
* NOTE: Now reading PowerMgmt in another location; is this still
* needed?
*/
pm_cap = pci_find_capability(pdev, PCI_CAP_ID_PM);
if (pm_cap == 0) {
dev_err(&adapter->pdev->dev,
"Cannot find Power Management capabilities\n");
result = -EIO;
goto err_release_res;
}
/* Check the DMA addressing support of this device */
if (!pci_set_dma_mask(pdev, 0xffffffffffffffffULL)) {
pci_using_dac = true;
result =
pci_set_consistent_dma_mask(pdev, 0xffffffffffffffffULL);
if (result != 0) {
dev_err(&pdev->dev,
"Unable to obtain 64 bit DMA for consistent allocations\n");
goto err_release_res;
}
} else if (!pci_set_dma_mask(pdev, 0xffffffffULL)) {
pci_using_dac = false;
} else {
dev_err(&adapter->pdev->dev,
"No usable DMA addressing method\n");
result = -EIO;
goto err_release_res;
}
/* Allocate netdev and private adapter structs */
netdev = et131x_device_alloc();
if (netdev == NULL) {
dev_err(&adapter->pdev->dev,
"Couldn't alloc netdev struct\n");
result = -ENOMEM;
goto err_release_res;
}
/* Setup the fundamental net_device and private adapter structure elements */
SET_NETDEV_DEV(netdev, &pdev->dev);
/*
if (pci_using_dac) {
netdev->features |= NETIF_F_HIGHDMA;
}
*/
/*
* NOTE - Turn this on when we're ready to deal with SG-DMA
*
* NOTE: According to "Linux Device Drivers", 3rd ed, Rubini et al,
* if checksumming is not performed in HW, then the kernel will not
* use SG.
* From pp 510-511:
*
* "Note that the kernel does not perform scatter/gather I/O to your
* device if it does not also provide some form of checksumming as
* well. The reason is that, if the kernel has to make a pass over a
* fragmented ("nonlinear") packet to calculate the checksum, it
* might as well copy the data and coalesce the packet at the same
* time."
*
* This has been verified by setting the flags below and still not
* receiving a scattered buffer from the network stack, so leave it
* off until checksums are calculated in HW.
*/
/* netdev->features |= NETIF_F_SG; */
/* netdev->features |= NETIF_F_NO_CSUM; */
/* netdev->features |= NETIF_F_LLTX; */
/* Allocate private adapter struct and copy in relevant information */
adapter = netdev_priv(netdev);
adapter->pdev = pci_dev_get(pdev);
adapter->netdev = netdev;
/* Do the same for the netdev struct */
netdev->irq = pdev->irq;
netdev->base_addr = pdev->resource[0].start;
/* Initialize spinlocks here */
spin_lock_init(&adapter->Lock);
spin_lock_init(&adapter->TCBSendQLock);
spin_lock_init(&adapter->TCBReadyQLock);
spin_lock_init(&adapter->SendHWLock);
spin_lock_init(&adapter->SendWaitLock);
spin_lock_init(&adapter->RcvLock);
spin_lock_init(&adapter->RcvPendLock);
spin_lock_init(&adapter->FbrLock);
spin_lock_init(&adapter->PHYLock);
/* Parse configuration parameters into the private adapter struct */
et131x_config_parse(adapter);
/* Find the physical adapter
*
* NOTE: This is the equivalent of the MpFindAdapter() routine; can we
* lump it's init with the device specific init below into a
* single init function?
*/
/* while (et131x_find_adapter(adapter, pdev) != 0); */
et131x_find_adapter(adapter, pdev);
/* Map the bus-relative registers to system virtual memory */
adapter->regs = ioremap_nocache(pci_resource_start(pdev, 0),
pci_resource_len(pdev, 0));
if (adapter->regs == NULL) {
dev_err(&pdev->dev, "Cannot map device registers\n");
result = -ENOMEM;
goto err_free_dev;
}
/* Perform device-specific initialization here (See code below) */
/* If Phy COMA mode was enabled when we went down, disable it here. */
writel(ET_PMCSR_INIT, &adapter->regs->global.pm_csr);
/* Issue a global reset to the et1310 */
et131x_soft_reset(adapter);
/* Disable all interrupts (paranoid) */
et131x_disable_interrupts(adapter);
/* Allocate DMA memory */
result = et131x_adapter_memory_alloc(adapter);
if (result != 0) {
dev_err(&pdev->dev, "Could not alloc adapater memory (DMA)\n");
goto err_iounmap;
}
/* Init send data structures */
et131x_init_send(adapter);
/* Register the interrupt
*
* NOTE - This is being done in the open routine, where most other
* Linux drivers setup IRQ handlers. Make sure device
* interrupts are not turned on before the IRQ is registered!!
*
* What we will do here is setup the task structure for the
* ISR's deferred handler
*/
INIT_WORK(&adapter->task, et131x_isr_handler);
/* Determine MAC Address, and copy into the net_device struct */
et131x_setup_hardware_properties(adapter);
memcpy(netdev->dev_addr, adapter->CurrentAddress, ETH_ALEN);
/* Setup et1310 as per the documentation */
et131x_adapter_setup(adapter);
/* Create a timer to count errors received by the NIC */
init_timer(&adapter->ErrorTimer);
adapter->ErrorTimer.expires = jiffies + TX_ERROR_PERIOD * HZ / 1000;
adapter->ErrorTimer.function = et131x_error_timer_handler;
adapter->ErrorTimer.data = (unsigned long)adapter;
/* Initialize link state */
et131x_link_detection_handler((unsigned long)adapter);
/* Intialize variable for counting how long we do not have
link status */
adapter->PoMgmt.TransPhyComaModeOnBoot = 0;
/* We can enable interrupts now
*
* NOTE - Because registration of interrupt handler is done in the
* device's open(), defer enabling device interrupts to that
* point
*/
/* Register the net_device struct with the Linux network layer */
result = register_netdev(netdev);
if (result != 0) {
dev_err(&pdev->dev, "register_netdev() failed\n");
goto err_mem_free;
}
/* Register the net_device struct with the PCI subsystem. Save a copy
* of the PCI config space for this device now that the device has
* been initialized, just in case it needs to be quickly restored.
*/
pci_set_drvdata(pdev, netdev);
pci_save_state(adapter->pdev);
out:
return result;
err_mem_free:
et131x_adapter_memory_free(adapter);
err_iounmap:
iounmap(adapter->regs);
err_free_dev:
pci_dev_put(pdev);
free_netdev(netdev);
err_release_res:
pci_release_regions(pdev);
err_disable:
pci_disable_device(pdev);
goto out;
}
void et131x_Mii_check(struct et131x_adapter *etdev,
MI_BMSR_t bmsr, MI_BMSR_t bmsr_ints)
{
uint8_t link_status;
uint32_t autoneg_status;
uint32_t speed;
uint32_t duplex;
uint32_t mdi_mdix;
uint32_t masterslave;
uint32_t polarity;
unsigned long flags;
if (bmsr_ints.bits.link_status) {
if (bmsr.bits.link_status) {
etdev->PoMgmt.TransPhyComaModeOnBoot = 20;
/* Update our state variables and indicate the
* connected state
*/
spin_lock_irqsave(&etdev->Lock, flags);
etdev->MediaState = NETIF_STATUS_MEDIA_CONNECT;
etdev->Flags &= ~fMP_ADAPTER_LINK_DETECTION;
spin_unlock_irqrestore(&etdev->Lock, flags);
/* Don't indicate state if we're in loopback mode */
if (etdev->RegistryPhyLoopbk == false)
netif_carrier_on(etdev->netdev);
} else {
dev_warn(&etdev->pdev->dev,
"Link down - cable problem ?\n");
if (etdev->linkspeed == TRUEPHY_SPEED_10MBPS) {
/* NOTE - Is there a way to query this without
* TruePHY?
* && TRU_QueryCoreType(etdev->hTruePhy, 0) == EMI_TRUEPHY_A13O) {
*/
uint16_t Register18;
MiRead(etdev, 0x12, &Register18);
MiWrite(etdev, 0x12, Register18 | 0x4);
MiWrite(etdev, 0x10, Register18 | 0x8402);
MiWrite(etdev, 0x11, Register18 | 511);
MiWrite(etdev, 0x12, Register18);
}
/* For the first N seconds of life, we are in "link
* detection" When we are in this state, we should
* only report "connected". When the LinkDetection
* Timer expires, we can report disconnected (handled
* in the LinkDetectionDPC).
*/
if (!(etdev->Flags & fMP_ADAPTER_LINK_DETECTION) ||
(etdev->MediaState == NETIF_STATUS_MEDIA_DISCONNECT)) {
spin_lock_irqsave(&etdev->Lock, flags);
etdev->MediaState =
NETIF_STATUS_MEDIA_DISCONNECT;
spin_unlock_irqrestore(&etdev->Lock,
flags);
/* Only indicate state if we're in loopback
* mode
*/
if (etdev->RegistryPhyLoopbk == false)
netif_carrier_off(etdev->netdev);
}
etdev->linkspeed = 0;
etdev->duplex_mode = 0;
/* Free the packets being actively sent & stopped */
et131x_free_busy_send_packets(etdev);
/* Re-initialize the send structures */
et131x_init_send(etdev);
/* Reset the RFD list and re-start RU */
et131x_reset_recv(etdev);
/*
* Bring the device back to the state it was during
* init prior to autonegotiation being complete. This
* way, when we get the auto-neg complete interrupt,
* we can complete init by calling ConfigMacREGS2.
*/
et131x_soft_reset(etdev);
/* Setup ET1310 as per the documentation */
et131x_adapter_setup(etdev);
/* Setup the PHY into coma mode until the cable is
* plugged back in
*/
if (etdev->RegistryPhyComa == 1)
EnablePhyComa(etdev);
}
}
if (bmsr_ints.bits.auto_neg_complete ||
(etdev->AiForceDpx == 3 && bmsr_ints.bits.link_status)) {
if (bmsr.bits.auto_neg_complete || etdev->AiForceDpx == 3) {
ET1310_PhyLinkStatus(etdev,
&link_status, &autoneg_status,
&speed, &duplex, &mdi_mdix,
&masterslave, &polarity);
etdev->linkspeed = speed;
etdev->duplex_mode = duplex;
etdev->PoMgmt.TransPhyComaModeOnBoot = 20;
if (etdev->linkspeed == TRUEPHY_SPEED_10MBPS) {
/*
* NOTE - Is there a way to query this without
* TruePHY?
* && TRU_QueryCoreType(etdev->hTruePhy, 0)== EMI_TRUEPHY_A13O) {
*/
uint16_t Register18;
MiRead(etdev, 0x12, &Register18);
MiWrite(etdev, 0x12, Register18 | 0x4);
MiWrite(etdev, 0x10, Register18 | 0x8402);
MiWrite(etdev, 0x11, Register18 | 511);
MiWrite(etdev, 0x12, Register18);
}
ConfigFlowControl(etdev);
if (etdev->linkspeed == TRUEPHY_SPEED_1000MBPS &&
etdev->RegistryJumboPacket > 2048)
ET1310_PhyAndOrReg(etdev, 0x16, 0xcfff,
0x2000);
SetRxDmaTimer(etdev);
ConfigMACRegs2(etdev);
}
}
}
