int board_init( void )
{
DECLARE_GLOBAL_DATA_PTR;
/* Active BBUS modules */
*get_bbus_reg_addr( NS9750_BBUS_MASTER_RESET ) = 0;
#warning Please register your machine at http://www.arm.linux.org.uk/developer/machines/?action=new
/* arch number of OMAP 1510-Board */
/* to be changed for OMAP 1610 Board */
gd->bd->bi_arch_number = 234;
/* adress of boot parameters */
gd->bd->bi_boot_params = 0x10000100;
/* this speeds up your boot a quite a bit. However to make it
* work, you need make sure your kernel startup flush bug is fixed.
* ... rkw ...
*/
icache_enable();
flash__init();
ether__init();
return 0;
}
int board_init (void)
{
if (machine_is_omap_h2())
gd->bd->bi_arch_number = MACH_TYPE_OMAP_H2;
else if (machine_is_omap_innovator())
gd->bd->bi_arch_number = MACH_TYPE_OMAP_INNOVATOR;
else
gd->bd->bi_arch_number = MACH_TYPE_OMAP_GENERIC;
/* adress of boot parameters */
gd->bd->bi_boot_params = 0x10000100;
/* Configure MUX settings */
set_muxconf_regs ();
peripheral_power_enable ();
/* this speeds up your boot a quite a bit. However to make it
* work, you need make sure your kernel startup flush bug is fixed.
* ... rkw ...
*/
icache_enable ();
flash__init ();
ether__init ();
return 0;
}
int board_init (void)
{
gd->bd->bi_arch_number = MACH_TYPE_OMAP_OSK;
/* adress of boot parameters */
gd->bd->bi_boot_params = 0x10000100;
flash__init();
ether__init();
return 0;
}
/*
* Miscellaneous platform dependent initialisations
*/
int board_init (void)
{
volatile unsigned int test;
icache_enable ();
ether__init ();
lcd__init();
gd->bd->bi_arch_number = MACH_TYPE_LF1000;
gd->bd->bi_boot_params = CONFIG_LF1000_BOOT_PARAMS_ADDR;
return 0;
}
int board_init (void)
{
/* arch number of OMAP 1510-Board */
gd->bd->bi_arch_number = MACH_TYPE_OMAP_INNOVATOR;
/* adress of boot parameters */
gd->bd->bi_boot_params = 0x10000100;
/* kk - this speeds up your boot a quite a bit. However to make it
* work, you need make sure your kernel startup flush bug is fixed.
* ... rkw ...
*/
icache_enable ();
flash__init ();
ether__init ();
return 0;
}
int board_init (void)
{
/* arch number of OMAP 730 P2 Board - Same as the Innovator! */
gd->bd->bi_arch_number = MACH_TYPE_OMAP_PERSEUS2;
/* adress of boot parameters */
gd->bd->bi_boot_params = 0x10000100;
/* Configure MUX settings */
set_muxconf_regs ();
peripheral_power_enable ();
/* Backup LED indication via GPIO_140 -> Red led if MUX correctly setup */
toggle_backup_led();
/* Hold GSM in reset until needed */
*((volatile unsigned short *)M_CTL) &= ~1;
/*
* CSx timings, GPIO Mux ... setup
*/
/* Flash: CS0 timings setup */
*((volatile unsigned int *) FLASH_CFG_0) = 0x0000fff3;
*((volatile unsigned int *) FLASH_ACFG_0_1) = 0x00000088;
/* Ethernet support trough the debug board */
/* CS1 timings setup */
*((volatile unsigned int *) FLASH_CFG_1) = 0x0000fff3;
*((volatile unsigned int *) FLASH_ACFG_0_1) = 0x00000000;
/* this speeds up your boot a quite a bit. However to make it
* work, you need make sure your kernel startup flush bug is fixed.
* ... rkw ...
*/
icache_enable ();
flash__init ();
ether__init ();
return 0;
}
int board_init (void)
{
/* arch number of Integrator Board */
gd->bd->bi_arch_number = MACH_TYPE_CINTEGRATOR;
/* adress of boot parameters */
gd->bd->bi_boot_params = 0x00000100;
gd->flags = 0;
#ifdef CONFIG_CM_REMAP
extern void cm_remap(void);
cm_remap(); /* remaps writeable memory to 0x00000000 */
#endif
icache_enable ();
flash__init ();
ether__init ();
return 0;
}
