Ejemplos de fec_init_decode en C++ (Cpp)

Ejemplo n.º 1

Archivo: phy_timing_test.c Proyecto: GlennVDLocht/dash7-ap-open-source-stack

unsigned int test_fec_decoding(void)
{
	uint8_t input[15] = {0x00, 0x01, 0x02, 0x03, 0x04, 0x05, 0x06, 0x07, 0x08, 0x09, 0x0A, 0x0B, 0x0C, 0x0D, 0x0E};
	uint8_t output[32];

	TimerA_configureContinuousMode(__MSP430_BASEADDRESS_T0A5__, TIMERA_CLOCKSOURCE_SMCLK, TIMERA_CLOCKSOURCE_DIVIDER_1, TIMERA_TAIE_INTERRUPT_DISABLE, TIMERA_DO_CLEAR);

	fec_init_encode(input);
	fec_set_length(15);
	fec_encode(&output[0]);
	fec_encode(&output[4]);
	fec_encode(&output[8]);
	fec_encode(&output[12]);
	fec_encode(&output[16]);
	fec_encode(&output[20]);
	fec_encode(&output[24]);
	fec_encode(&output[28]);

	memset(input, 0, 15);

	fec_init_decode(input);
	fec_set_length(15);

	TimerA_clear(__MSP430_BASEADDRESS_T0A5__);
	fec_decode(&output[0]);
	fec_decode(&output[4]);
	fec_decode(&output[8]);
	fec_decode(&output[12]);
	fec_decode(&output[16]);
	fec_decode(&output[20]);
	fec_decode(&output[24]);
	fec_decode(&output[28]);
	TimerA_stop(__MSP430_BASEADDRESS_T0A5__);

	return TA0R - TIMER_OFFSET;
}

Ejemplo n.º 2

bool phy_rx(phy_rx_cfg_t* cfg)
{
#ifdef LOG_PHY_ENABLED
    log_print_stack_string(LOG_PHY, "phy_rx");
#endif

    RadioState current_state = get_radiostate();
    if(current_state != Idle && current_state != Receive)
    {
#ifdef LOG_PHY_ENABLED
        log_print_stack_string(LOG_PHY, "PHY Cannot RX, PHy not idle");
#endif
        return false;
    }

    //Set radio state
    state = Receive;

    //Flush the txfifo
    Strobe(RF_SIDLE);
    Strobe(RF_SFRX);

    //Set configuration

    if (!phy_translate_and_set_settings(cfg->spectrum_id, cfg->sync_word_class))
        return false;

    set_timeout(cfg->timeout);

//TODO Return error if fec not enabled but requested
#ifdef D7_PHY_USE_FEC
    if (fec) {
        //Disable hardware data whitening
        set_data_whitening(false);

        //Initialize fec encoding
        fec_init_decode(buffer);

        //Configure length settings
        set_length_infinite(true);

        if(cfg->length == 0)
        {
            packetLength = 0;
            remainingBytes = 0;
            WriteSingleReg(PKTLEN, 0xFF);
            WriteSingleReg(FIFOTHR, RADIO_FIFOTHR_FIFO_THR_61_4);
        } else {
            fec_set_length(cfg->length);
            packetLength = ((cfg->length & 0xFE) + 2) << 1;
            remainingBytes = packetLength;
            WriteSingleReg(PKTLEN, (uint8_t)(packetLength & 0x00FF));
            WriteSingleReg(FIFOTHR, RADIO_FIFOTHR_FIFO_THR_17_48);
        }
    } else {
#endif
        //Enable hardware data whitening
        set_data_whitening(true);

        //Set buffer position
        bufferPosition = buffer;

        //Configure length settings and txfifo threshold
        set_length_infinite(false);

        if(cfg->length == 0)
        {
            packetLength = 0;
            remainingBytes = 0;
            WriteSingleReg(PKTLEN, 0xFF);
            WriteSingleReg(FIFOTHR, RADIO_FIFOTHR_FIFO_THR_61_4);
        } else {
            packetLength = cfg->length;
            remainingBytes = packetLength;
            WriteSingleReg(PKTLEN, packetLength);
            WriteSingleReg(FIFOTHR, RADIO_FIFOTHR_FIFO_THR_17_48);
        }
#ifdef D7_PHY_USE_FEC
    }
#endif

    //TODO: set minimum sync word rss to scan minimum energy
    //Enable interrupts
    phy_set_gdo_values(GDOLine2, GDO_EDGE_RXFilled, GDO_SETTING_RXFilled);
    phy_set_gdo_values(GDOLine0, GDO_EDGE_EndOfPacket, GDO_SETTING_EndOfPacket);
    radioClearInterruptPendingLines();
    radioEnableGDO2Interrupt();
    radioEnableGDO0Interrupt();

    //Start receiving
    Strobe(RF_SRX);

    return true;
}