void validateAndFixConfig(void)
{
if (!(feature(FEATURE_RX_PARALLEL_PWM) || feature(FEATURE_RX_PPM) || feature(FEATURE_RX_SERIAL) || feature(FEATURE_RX_MSP))) {
featureSet(FEATURE_RX_PARALLEL_PWM); // Consider changing the default to PPM
}
if (feature(FEATURE_RX_PPM)) {
featureClear(FEATURE_RX_PARALLEL_PWM);
}
if (feature(FEATURE_RX_MSP)) {
featureClear(FEATURE_RX_SERIAL);
featureClear(FEATURE_RX_PARALLEL_PWM);
featureClear(FEATURE_RX_PPM);
}
if (feature(FEATURE_RX_SERIAL)) {
featureClear(FEATURE_RX_PARALLEL_PWM);
featureClear(FEATURE_RX_PPM);
}
if (feature(FEATURE_RX_PARALLEL_PWM)) {
#if defined(STM32F10X)
// rssi adc needs the same ports
featureClear(FEATURE_RSSI_ADC);
// current meter needs the same ports
if (masterConfig.batteryConfig.currentMeterType == CURRENT_SENSOR_ADC) {
featureClear(FEATURE_CURRENT_METER);
}
#endif
#if defined(STM32F10X) || defined(CHEBUZZ) || defined(STM32F3DISCOVERY)
// led strip needs the same ports
featureClear(FEATURE_LED_STRIP);
#endif
// software serial needs free PWM ports
featureClear(FEATURE_SOFTSERIAL);
}
#if defined(LED_STRIP) && (defined(USE_SOFTSERIAL1) || defined(USE_SOFTSERIAL2))
if (feature(FEATURE_SOFTSERIAL) && (
0
#ifdef USE_SOFTSERIAL1
|| (LED_STRIP_TIMER == SOFTSERIAL_1_TIMER)
#endif
#ifdef USE_SOFTSERIAL2
|| (LED_STRIP_TIMER == SOFTSERIAL_2_TIMER)
#endif
)) {
// led strip needs the same timer as softserial
featureClear(FEATURE_LED_STRIP);
}
#endif
#if defined(NAZE) && defined(SONAR)
if (feature(FEATURE_RX_PARALLEL_PWM) && feature(FEATURE_SONAR) && feature(FEATURE_CURRENT_METER) && masterConfig.batteryConfig.currentMeterType == CURRENT_SENSOR_ADC) {
featureClear(FEATURE_CURRENT_METER);
}
#endif
#if defined(OLIMEXINO) && defined(SONAR)
if (feature(FEATURE_SONAR) && feature(FEATURE_CURRENT_METER) && masterConfig.batteryConfig.currentMeterType == CURRENT_SENSOR_ADC) {
featureClear(FEATURE_CURRENT_METER);
}
#endif
#if defined(CC3D) && defined(DISPLAY) && defined(USE_USART3)
if (doesConfigurationUsePort(SERIAL_PORT_USART3) && feature(FEATURE_DISPLAY)) {
featureClear(FEATURE_DISPLAY);
}
#endif
/*
* The retarded_arm setting is incompatible with pid_at_min_throttle because full roll causes the craft to roll over on the ground.
* The pid_at_min_throttle implementation ignores yaw on the ground, but doesn't currently ignore roll when retarded_arm is enabled.
*/
if (masterConfig.retarded_arm && masterConfig.mixerConfig.pid_at_min_throttle) {
masterConfig.mixerConfig.pid_at_min_throttle = 0;
}
useRxConfig(&masterConfig.rxConfig);
serialConfig_t *serialConfig = &masterConfig.serialConfig;
if (!isSerialConfigValid(serialConfig)) {
resetSerialConfig(serialConfig);
}
}
void validateAndFixConfig(void)
{
if (!(feature(FEATURE_RX_PARALLEL_PWM) || feature(FEATURE_RX_PPM) || feature(FEATURE_RX_SERIAL) || feature(FEATURE_RX_MSP))) {
featureSet(FEATURE_RX_PARALLEL_PWM); // Consider changing the default to PPM
}
if (feature(FEATURE_RX_PPM)) {
featureClear(FEATURE_RX_PARALLEL_PWM);
}
if (feature(FEATURE_RX_MSP)) {
featureClear(FEATURE_RX_SERIAL);
featureClear(FEATURE_RX_PARALLEL_PWM);
featureClear(FEATURE_RX_PPM);
}
if (feature(FEATURE_RX_SERIAL)) {
featureClear(FEATURE_RX_PARALLEL_PWM);
featureClear(FEATURE_RX_PPM);
}
if (feature(FEATURE_RX_PARALLEL_PWM)) {
#if defined(STM32F10X)
// rssi adc needs the same ports
featureClear(FEATURE_RSSI_ADC);
// current meter needs the same ports
featureClear(FEATURE_CURRENT_METER);
#endif
#if defined(STM32F10X) || defined(CHEBUZZ) || defined(STM32F3DISCOVERY)
// led strip needs the same ports
featureClear(FEATURE_LED_STRIP);
#endif
// software serial needs free PWM ports
featureClear(FEATURE_SOFTSERIAL);
}
#if defined(LED_STRIP) && (defined(USE_SOFTSERIAL1) || defined(USE_SOFTSERIAL2))
if (feature(FEATURE_SOFTSERIAL) && (
#ifdef USE_SOFTSERIAL1
(LED_STRIP_TIMER == SOFTSERIAL_1_TIMER)
#else
0
#endif
||
#ifdef USE_SOFTSERIAL2
(LED_STRIP_TIMER == SOFTSERIAL_2_TIMER)
#else
0
#endif
)) {
// led strip needs the same timer as softserial
featureClear(FEATURE_LED_STRIP);
}
#endif
#if defined(NAZE) && defined(SONAR)
if (feature(FEATURE_RX_PARALLEL_PWM) && feature(FEATURE_SONAR) && feature(FEATURE_CURRENT_METER)) {
featureClear(FEATURE_CURRENT_METER);
}
#endif
#if defined(OLIMEXINO) && defined(SONAR)
if (feature(FEATURE_SONAR) && feature(FEATURE_CURRENT_METER)) {
featureClear(FEATURE_CURRENT_METER);
}
#endif
useRxConfig(&masterConfig.rxConfig);
serialConfig_t *serialConfig = &masterConfig.serialConfig;
applySerialConfigToPortFunctions(serialConfig);
if (!isSerialConfigValid(serialConfig)) {
resetSerialConfig(serialConfig);
}
}
static void validateAndFixConfig(void)
{
if (!(featureConfigured(FEATURE_RX_PARALLEL_PWM) || featureConfigured(FEATURE_RX_PPM) || featureConfigured(FEATURE_RX_SERIAL) || featureConfigured(FEATURE_RX_MSP))) {
featureSet(DEFAULT_RX_FEATURE);
}
if (featureConfigured(FEATURE_RX_PPM)) {
featureClear(FEATURE_RX_PARALLEL_PWM | FEATURE_RX_SERIAL | FEATURE_RX_MSP);
}
if (featureConfigured(FEATURE_RX_MSP)) {
featureClear(FEATURE_RX_SERIAL | FEATURE_RX_PARALLEL_PWM | FEATURE_RX_PPM);
}
if (featureConfigured(FEATURE_RX_SERIAL)) {
featureClear(FEATURE_RX_PARALLEL_PWM | FEATURE_RX_MSP | FEATURE_RX_PPM);
}
if (featureConfigured(FEATURE_RX_PARALLEL_PWM)) {
featureClear(FEATURE_RX_SERIAL | FEATURE_RX_MSP | FEATURE_RX_PPM);
}
// The retarded_arm setting is incompatible with pid_at_min_throttle because full roll causes the craft to roll over on the ground.
// The pid_at_min_throttle implementation ignores yaw on the ground, but doesn't currently ignore roll when retarded_arm is enabled.
if (armingConfig()->retarded_arm && mixerConfig()->pid_at_min_throttle) {
mixerConfig()->pid_at_min_throttle = 0;
}
if (gyroConfig()->gyro_soft_notch_hz < gyroConfig()->gyro_soft_notch_cutoff_hz) {
gyroConfig()->gyro_soft_notch_hz = gyroConfig()->gyro_soft_notch_cutoff_hz;
}
#if defined(LED_STRIP)
#if (defined(USE_SOFTSERIAL1) || defined(USE_SOFTSERIAL2))
if (featureConfigured(FEATURE_SOFTSERIAL) && (
0
#ifdef USE_SOFTSERIAL1
|| (LED_STRIP_TIMER == SOFTSERIAL_1_TIMER)
#endif
#ifdef USE_SOFTSERIAL2
|| (LED_STRIP_TIMER == SOFTSERIAL_2_TIMER)
#endif
)) {
// led strip needs the same timer as softserial
featureClear(FEATURE_LED_STRIP);
}
#endif
#if defined(TRANSPONDER) && !defined(UNIT_TEST)
if ((WS2811_DMA_TC_FLAG == TRANSPONDER_DMA_TC_FLAG) && featureConfigured(FEATURE_TRANSPONDER) && featureConfigured(FEATURE_LED_STRIP)) {
featureClear(FEATURE_LED_STRIP);
}
#endif
#endif // LED_STRIP
#if defined(CC3D)
#if defined(DISPLAY) && defined(USE_UART3)
if (featureConfigured(FEATURE_DISPLAY) && doesConfigurationUsePort(SERIAL_PORT_UART3)) {
featureClear(FEATURE_DISPLAY);
}
#endif
#if defined(SONAR) && defined(USE_SOFTSERIAL1)
if (featureConfigured(FEATURE_SONAR) && featureConfigured(FEATURE_SOFTSERIAL)) {
featureClear(FEATURE_SONAR);
}
#endif
#if defined(SONAR) && defined(USE_SOFTSERIAL1) && defined(RSSI_ADC_GPIO)
// shared pin
if ((featureConfigured(FEATURE_SONAR) + featureConfigured(FEATURE_SOFTSERIAL) + featureConfigured(FEATURE_RSSI_ADC)) > 1) {
featureClear(FEATURE_SONAR);
featureClear(FEATURE_SOFTSERIAL);
featureClear(FEATURE_RSSI_ADC);
}
#endif
#endif // CC3D
#if defined(COLIBRI_RACE)
serialConfig()->portConfigs[0].functionMask = FUNCTION_MSP_SERVER;
if (featureConfigured(FEATURE_RX_SERIAL)) {
serialConfig()->portConfigs[2].functionMask = FUNCTION_RX_SERIAL;
}
#endif
#if defined(SPRACINGF3NEO_REV) && (SPRACINGF3NEO_REV < 5)
if (featureConfigured(FEATURE_OSD) && featureConfigured(FEATURE_TRANSPONDER)) {
featureClear(FEATURE_TRANSPONDER);
}
if (featureConfigured(FEATURE_OSD) && featureConfigured(FEATURE_LED_STRIP)) {
featureClear(FEATURE_LED_STRIP);
}
#endif
if (!isSerialConfigValid(serialConfig())) {
PG_RESET_CURRENT(serialConfig);
}
#if defined(USE_VCP)
serialConfig()->portConfigs[0].functionMask = FUNCTION_MSP_SERVER;
#endif
}
static void validateAndFixConfig(void)
{
if (!(featureConfigured(FEATURE_RX_PARALLEL_PWM) || featureConfigured(FEATURE_RX_PPM) || featureConfigured(FEATURE_RX_SERIAL) || featureConfigured(FEATURE_RX_MSP) || featureConfigured(FEATURE_RX_NRF24))) {
featureSet(DEFAULT_RX_FEATURE);
}
if (featureConfigured(FEATURE_RX_PPM)) {
featureClear(FEATURE_RX_SERIAL | FEATURE_RX_PARALLEL_PWM | FEATURE_RX_MSP | FEATURE_RX_NRF24);
}
if (featureConfigured(FEATURE_RX_MSP)) {
featureClear(FEATURE_RX_SERIAL | FEATURE_RX_PARALLEL_PWM | FEATURE_RX_PPM | FEATURE_RX_NRF24);
}
if (featureConfigured(FEATURE_RX_SERIAL)) {
featureClear(FEATURE_RX_PARALLEL_PWM | FEATURE_RX_MSP | FEATURE_RX_PPM | FEATURE_RX_NRF24);
}
if (featureConfigured(FEATURE_RX_NRF24)) {
featureClear(FEATURE_RX_SERIAL | FEATURE_RX_PARALLEL_PWM | FEATURE_RX_PPM | FEATURE_RX_MSP);
}
#if defined(NAV)
// Ensure sane values of navConfig settings
validateNavConfig(&masterConfig.navConfig);
#endif
if (featureConfigured(FEATURE_SOFTSPI)) {
featureClear(FEATURE_RX_PPM | FEATURE_RX_PARALLEL_PWM | FEATURE_SOFTSERIAL | FEATURE_VBAT);
#if defined(STM32F10X)
featureClear(FEATURE_LED_STRIP);
// rssi adc needs the same ports
featureClear(FEATURE_RSSI_ADC);
// current meter needs the same ports
if (masterConfig.batteryConfig.currentMeterType == CURRENT_SENSOR_ADC) {
featureClear(FEATURE_CURRENT_METER);
}
#endif
}
if (featureConfigured(FEATURE_RX_PARALLEL_PWM)) {
featureClear(FEATURE_RX_SERIAL | FEATURE_RX_MSP | FEATURE_RX_PPM | FEATURE_RX_NRF24);
#if defined(STM32F10X)
// rssi adc needs the same ports
featureClear(FEATURE_RSSI_ADC);
// current meter needs the same ports
if (masterConfig.batteryConfig.currentMeterType == CURRENT_SENSOR_ADC) {
featureClear(FEATURE_CURRENT_METER);
}
#if defined(CC3D)
// There is a timer clash between PWM RX pins and motor output pins - this forces us to have same timer tick rate for these timers
// which is only possible when using brushless motors w/o oneshot (timer tick rate is PWM_TIMER_MHZ)
// On CC3D OneShot is incompatible with PWM RX
featureClear(FEATURE_ONESHOT125);
// Brushed motors on CC3D are not possible when using PWM RX
if (masterConfig.motor_pwm_rate > BRUSHLESS_MOTORS_PWM_RATE) {
masterConfig.motor_pwm_rate = BRUSHLESS_MOTORS_PWM_RATE;
}
#endif
#endif
#if defined(STM32F10X) || defined(CHEBUZZ) || defined(STM32F3DISCOVERY)
// led strip needs the same ports
featureClear(FEATURE_LED_STRIP);
#endif
// software serial needs free PWM ports
featureClear(FEATURE_SOFTSERIAL);
}
#ifdef STM32F10X
// avoid overloading the CPU on F1 targets when using gyro sync and GPS.
if (masterConfig.gyroSync && masterConfig.gyroSyncDenominator < 2 && featureConfigured(FEATURE_GPS)) {
masterConfig.gyroSyncDenominator = 2;
}
// avoid overloading the CPU when looptime < 2000 and GPS
if (masterConfig.looptime && featureConfigured(FEATURE_GPS)) {
masterConfig.looptime = 2000;
}
#endif
#if defined(LED_STRIP) && (defined(USE_SOFTSERIAL1) || defined(USE_SOFTSERIAL2))
if (featureConfigured(FEATURE_SOFTSERIAL) && (
0
#ifdef USE_SOFTSERIAL1
|| (WS2811_TIMER == SOFTSERIAL_1_TIMER)
#endif
#ifdef USE_SOFTSERIAL2
|| (WS2811_TIMER == SOFTSERIAL_2_TIMER)
#endif
)) {
// led strip needs the same timer as softserial
featureClear(FEATURE_LED_STRIP);
}
#endif
#if defined(NAZE) && defined(SONAR)
if (featureConfigured(FEATURE_RX_PARALLEL_PWM) && featureConfigured(FEATURE_SONAR) && featureConfigured(FEATURE_CURRENT_METER) && masterConfig.batteryConfig.currentMeterType == CURRENT_SENSOR_ADC) {
featureClear(FEATURE_CURRENT_METER);
}
#endif
#if defined(OLIMEXINO) && defined(SONAR)
if (feature(FEATURE_SONAR) && feature(FEATURE_CURRENT_METER) && masterConfig.batteryConfig.currentMeterType == CURRENT_SENSOR_ADC) {
featureClear(FEATURE_CURRENT_METER);
}
#endif
#if defined(CC3D) && defined(DISPLAY) && defined(USE_USART3)
if (doesConfigurationUsePort(SERIAL_PORT_USART3) && feature(FEATURE_DISPLAY)) {
featureClear(FEATURE_DISPLAY);
}
#endif
#ifdef STM32F303xC
// hardware supports serial port inversion, make users life easier for those that want to connect SBus RX's
#ifdef TELEMETRY
masterConfig.telemetryConfig.telemetry_inversion = 1;
#endif
#endif
#if defined(CC3D)
#if defined(CC3D_PPM1)
#if defined(SONAR) && defined(USE_SOFTSERIAL1)
if (feature(FEATURE_SONAR) && feature(FEATURE_SOFTSERIAL)) {
featureClear(FEATURE_SONAR);
}
#endif
#else
#if defined(SONAR) && defined(USE_SOFTSERIAL1) && defined(RSSI_ADC_GPIO)
// shared pin
if ((featureConfigured(FEATURE_SONAR) + featureConfigured(FEATURE_SOFTSERIAL) + featureConfigured(FEATURE_RSSI_ADC)) > 1) {
featureClear(FEATURE_SONAR);
featureClear(FEATURE_SOFTSERIAL);
featureClear(FEATURE_RSSI_ADC);
}
#endif
#endif // CC3D_PPM1
#endif // CC3D
#if defined(COLIBRI_RACE)
masterConfig.serialConfig.portConfigs[0].functionMask = FUNCTION_MSP;
if(featureConfigured(FEATURE_RX_SERIAL)) {
masterConfig.serialConfig.portConfigs[2].functionMask = FUNCTION_RX_SERIAL;
}
#endif
useRxConfig(&masterConfig.rxConfig);
serialConfig_t *serialConfig = &masterConfig.serialConfig;
if (!isSerialConfigValid(serialConfig)) {
resetSerialConfig(serialConfig);
}
/*
* If provided predefined mixer setup is disabled, fallback to default one
*/
if (!isMixerEnabled(masterConfig.mixerMode)) {
masterConfig.mixerMode = DEFAULT_MIXER;
}
}
void validateAndFixConfig(void)
{
if (!(featureConfigured(FEATURE_RX_PARALLEL_PWM) || featureConfigured(FEATURE_RX_PPM) || featureConfigured(FEATURE_RX_SERIAL) || featureConfigured(FEATURE_RX_MSP))) {
featureSet(DEFAULT_RX_FEATURE);
}
if (featureConfigured(FEATURE_RX_PPM)) {
featureClear(FEATURE_RX_PARALLEL_PWM | FEATURE_RX_SERIAL | FEATURE_RX_MSP);
}
if (featureConfigured(FEATURE_RX_MSP)) {
featureClear(FEATURE_RX_SERIAL | FEATURE_RX_PARALLEL_PWM | FEATURE_RX_PPM);
}
if (featureConfigured(FEATURE_RX_SERIAL)) {
featureClear(FEATURE_RX_PARALLEL_PWM | FEATURE_RX_MSP | FEATURE_RX_PPM);
}
if (featureConfigured(FEATURE_RX_PARALLEL_PWM)) {
featureClear(FEATURE_RX_SERIAL | FEATURE_RX_MSP | FEATURE_RX_PPM);
}
#ifdef STM32F10X
// avoid overloading the CPU on F1 targets when using gyro sync and GPS.
if (imuConfig()->gyroSync && imuConfig()->gyroSyncDenominator < 2 && featureConfigured(FEATURE_GPS)) {
imuConfig()->gyroSyncDenominator = 2;
}
#endif
#if defined(LED_STRIP) && (defined(USE_SOFTSERIAL1) || defined(USE_SOFTSERIAL2))
if (featureConfigured(FEATURE_SOFTSERIAL) && (
0
#ifdef USE_SOFTSERIAL1
|| (LED_STRIP_TIMER == SOFTSERIAL_1_TIMER)
#endif
#ifdef USE_SOFTSERIAL2
|| (LED_STRIP_TIMER == SOFTSERIAL_2_TIMER)
#endif
)) {
// led strip needs the same timer as softserial
featureClear(FEATURE_LED_STRIP);
}
#endif
#if defined(CC3D) && defined(DISPLAY) && defined(USE_UART3)
if (doesConfigurationUsePort(SERIAL_PORT_UART3) && featureConfigured(FEATURE_DISPLAY)) {
featureClear(FEATURE_DISPLAY);
}
#endif
#ifdef STM32F303xC
// hardware supports serial port inversion, make users life easier for those that want to connect SBus RX's
#ifdef TELEMETRY
telemetryConfig()->telemetry_inversion = 1;
#endif
#endif
/*
* The retarded_arm setting is incompatible with pid_at_min_throttle because full roll causes the craft to roll over on the ground.
* The pid_at_min_throttle implementation ignores yaw on the ground, but doesn't currently ignore roll when retarded_arm is enabled.
*/
if (armingConfig()->retarded_arm && mixerConfig()->pid_at_min_throttle) {
mixerConfig()->pid_at_min_throttle = 0;
}
#if defined(LED_STRIP) && defined(TRANSPONDER) && !defined(UNIT_TEST)
if ((WS2811_DMA_TC_FLAG == TRANSPONDER_DMA_TC_FLAG) && featureConfigured(FEATURE_TRANSPONDER) && featureConfigured(FEATURE_LED_STRIP)) {
featureClear(FEATURE_LED_STRIP);
}
#endif
#if defined(CC3D) && defined(SONAR) && defined(USE_SOFTSERIAL1) && defined(RSSI_ADC_GPIO)
// shared pin
if ((featureConfigured(FEATURE_SONAR) + featureConfigured(FEATURE_SOFTSERIAL) + featureConfigured(FEATURE_RSSI_ADC)) > 1) {
featureClear(FEATURE_SONAR);
featureClear(FEATURE_SOFTSERIAL);
featureClear(FEATURE_RSSI_ADC);
}
#endif
#if defined(COLIBRI_RACE)
serialConfig()->portConfigs[0].functionMask = FUNCTION_MSP;
if (featureConfigured(FEATURE_RX_SERIAL)) {
serialConfig()->portConfigs[2].functionMask = FUNCTION_RX_SERIAL;
}
#endif
if (!isSerialConfigValid(serialConfig())) {
PG_RESET_CURRENT(serialConfig);
}
#if defined(USE_VCP)
serialConfig()->portConfigs[0].functionMask = FUNCTION_MSP;
#endif
}
void validateAndFixConfig(void)
{
if (!(feature(FEATURE_RX_PARALLEL_PWM) || feature(FEATURE_RX_PPM) || feature(FEATURE_RX_SERIAL) || feature(FEATURE_RX_MSP))) {
featureSet(FEATURE_RX_PARALLEL_PWM); // Consider changing the default to PPM
}
if (feature(FEATURE_RX_PPM)) {
featureClear(FEATURE_RX_PARALLEL_PWM);
}
if (feature(FEATURE_RX_MSP)) {
featureClear(FEATURE_RX_SERIAL);
featureClear(FEATURE_RX_PARALLEL_PWM);
featureClear(FEATURE_RX_PPM);
}
if (feature(FEATURE_RX_SERIAL)) {
featureClear(FEATURE_RX_PARALLEL_PWM);
featureClear(FEATURE_RX_PPM);
}
if (feature(FEATURE_RX_PARALLEL_PWM)) {
#if defined(STM32F103_MD)
// rssi adc needs the same ports
featureClear(FEATURE_RSSI_ADC);
// current meter needs the same ports
featureClear(FEATURE_CURRENT_METER);
#ifdef SONAR
// sonar needs a free PWM port
featureClear(FEATURE_SONAR);
#endif
#endif
#if defined(STM32F103_MD) || defined(CHEBUZZ) || defined(STM32F3DISCOVERY)
// led strip needs the same ports
featureClear(FEATURE_LED_STRIP);
#endif
// software serial needs free PWM ports
featureClear(FEATURE_SOFTSERIAL);
}
#if defined(STM32F103_MD)
// led strip needs the same timer as softserial
if (feature(FEATURE_SOFTSERIAL)) {
featureClear(FEATURE_LED_STRIP);
}
#endif
useRxConfig(&masterConfig.rxConfig);
serialConfig_t *serialConfig = &masterConfig.serialConfig;
applySerialConfigToPortFunctions(serialConfig);
if (!isSerialConfigValid(serialConfig)) {
resetSerialConfig(serialConfig);
}
static void validateAndFixConfig(void)
{
#if !defined(USE_QUAD_MIXER_ONLY) && !defined(USE_OSD_SLAVE)
// Reset unsupported mixer mode to default.
// This check will be gone when motor/servo mixers are loaded dynamically
// by configurator as a part of configuration procedure.
mixerMode_e mixerMode = mixerConfigMutable()->mixerMode;
if (!(mixerMode == MIXER_CUSTOM || mixerMode == MIXER_CUSTOM_AIRPLANE || mixerMode == MIXER_CUSTOM_TRI)) {
if (mixers[mixerMode].motorCount && mixers[mixerMode].motor == NULL)
mixerConfigMutable()->mixerMode = MIXER_CUSTOM;
#ifdef USE_SERVOS
if (mixers[mixerMode].useServo && servoMixers[mixerMode].servoRuleCount == 0)
mixerConfigMutable()->mixerMode = MIXER_CUSTOM_AIRPLANE;
#endif
}
#endif
#ifndef USE_OSD_SLAVE
if (systemConfig()->activeRateProfile >= CONTROL_RATE_PROFILE_COUNT) {
systemConfigMutable()->activeRateProfile = 0;
}
setControlRateProfile(systemConfig()->activeRateProfile);
if (systemConfig()->pidProfileIndex >= MAX_PROFILE_COUNT) {
systemConfigMutable()->pidProfileIndex = 0;
}
setPidProfile(systemConfig()->pidProfileIndex);
// Prevent invalid notch cutoff
if (currentPidProfile->dterm_notch_cutoff >= currentPidProfile->dterm_notch_hz) {
currentPidProfile->dterm_notch_hz = 0;
}
if ((motorConfig()->dev.motorPwmProtocol == PWM_TYPE_BRUSHED) && (motorConfig()->mincommand < 1000)) {
motorConfigMutable()->mincommand = 1000;
}
if ((motorConfig()->dev.motorPwmProtocol == PWM_TYPE_STANDARD) && (motorConfig()->dev.motorPwmRate > BRUSHLESS_MOTORS_PWM_RATE)) {
motorConfigMutable()->dev.motorPwmRate = BRUSHLESS_MOTORS_PWM_RATE;
}
validateAndFixGyroConfig();
if (!(featureConfigured(FEATURE_RX_PARALLEL_PWM) || featureConfigured(FEATURE_RX_PPM) || featureConfigured(FEATURE_RX_SERIAL) || featureConfigured(FEATURE_RX_MSP) || featureConfigured(FEATURE_RX_SPI))) {
featureSet(DEFAULT_RX_FEATURE);
}
if (featureConfigured(FEATURE_RX_PPM)) {
featureClear(FEATURE_RX_SERIAL | FEATURE_RX_PARALLEL_PWM | FEATURE_RX_MSP | FEATURE_RX_SPI);
}
if (featureConfigured(FEATURE_RX_MSP)) {
featureClear(FEATURE_RX_SERIAL | FEATURE_RX_PARALLEL_PWM | FEATURE_RX_PPM | FEATURE_RX_SPI);
}
if (featureConfigured(FEATURE_RX_SERIAL)) {
featureClear(FEATURE_RX_PARALLEL_PWM | FEATURE_RX_MSP | FEATURE_RX_PPM | FEATURE_RX_SPI);
}
#ifdef USE_RX_SPI
if (featureConfigured(FEATURE_RX_SPI)) {
featureClear(FEATURE_RX_SERIAL | FEATURE_RX_PARALLEL_PWM | FEATURE_RX_PPM | FEATURE_RX_MSP);
}
#endif // USE_RX_SPI
if (featureConfigured(FEATURE_RX_PARALLEL_PWM)) {
featureClear(FEATURE_RX_SERIAL | FEATURE_RX_MSP | FEATURE_RX_PPM | FEATURE_RX_SPI);
#if defined(STM32F10X)
// rssi adc needs the same ports
featureClear(FEATURE_RSSI_ADC);
// current meter needs the same ports
if (batteryConfig()->currentMeterSource == CURRENT_METER_ADC) {
batteryConfigMutable()->currentMeterSource = CURRENT_METER_NONE;
}
#endif // STM32F10X
// software serial needs free PWM ports
featureClear(FEATURE_SOFTSERIAL);
}
#ifdef USE_SOFTSPI
if (featureConfigured(FEATURE_SOFTSPI)) {
featureClear(FEATURE_RX_PPM | FEATURE_RX_PARALLEL_PWM | FEATURE_SOFTSERIAL);
batteryConfigMutable()->voltageMeterSource = VOLTAGE_METER_NONE;
#if defined(STM32F10X)
featureClear(FEATURE_LED_STRIP);
// rssi adc needs the same ports
featureClear(FEATURE_RSSI_ADC);
// current meter needs the same ports
if (batteryConfig()->currentMeterSource == CURRENT_METER_ADC) {
batteryConfigMutable()->currentMeterSource = CURRENT_METER_NONE;
}
#endif // STM32F10X
}
#endif // USE_SOFTSPI
#endif // USE_OSD_SLAVE
if (!isSerialConfigValid(serialConfig())) {
pgResetFn_serialConfig(serialConfigMutable());
}
// clear features that are not supported.
// I have kept them all here in one place, some could be moved to sections of code above.
#ifndef USE_PPM
featureClear(FEATURE_RX_PPM);
#endif
#ifndef USE_SERIAL_RX
featureClear(FEATURE_RX_SERIAL);
#endif
#if !defined(USE_SOFTSERIAL1) && !defined(USE_SOFTSERIAL2)
featureClear(FEATURE_SOFTSERIAL);
#endif
#ifndef USE_GPS
featureClear(FEATURE_GPS);
#endif
#ifndef USE_RANGEFINDER
featureClear(FEATURE_RANGEFINDER);
#endif
#ifndef USE_TELEMETRY
featureClear(FEATURE_TELEMETRY);
#endif
#ifndef USE_PWM
featureClear(FEATURE_RX_PARALLEL_PWM);
#endif
#ifndef USE_RX_MSP
featureClear(FEATURE_RX_MSP);
#endif
#ifndef USE_LED_STRIP
featureClear(FEATURE_LED_STRIP);
#endif
#ifndef USE_DASHBOARD
featureClear(FEATURE_DASHBOARD);
#endif
#ifndef USE_OSD
featureClear(FEATURE_OSD);
#endif
#ifndef USE_SERVOS
featureClear(FEATURE_SERVO_TILT | FEATURE_CHANNEL_FORWARDING);
#endif
#ifndef USE_TRANSPONDER
featureClear(FEATURE_TRANSPONDER);
#endif
#ifndef USE_RX_SPI
featureClear(FEATURE_RX_SPI);
#endif
#ifndef USE_SOFTSPI
featureClear(FEATURE_SOFTSPI);
#endif
#ifndef USE_ESC_SENSOR
featureClear(FEATURE_ESC_SENSOR);
#endif
#ifndef USE_GYRO_DATA_ANALYSE
featureClear(FEATURE_DYNAMIC_FILTER);
#endif
#if defined(TARGET_VALIDATECONFIG)
targetValidateConfiguration();
#endif
}
void validateAndFixConfig(void)
{
if (!(featureConfigured(FEATURE_RX_PARALLEL_PWM) || featureConfigured(FEATURE_RX_PPM) || featureConfigured(FEATURE_RX_SERIAL) || featureConfigured(FEATURE_RX_MSP))) {
featureSet(DEFAULT_RX_FEATURE);
}
if (featureConfigured(FEATURE_RX_PPM)) {
featureClear(FEATURE_RX_PARALLEL_PWM);
}
if (featureConfigured(FEATURE_RX_MSP)) {
featureClear(FEATURE_RX_SERIAL);
featureClear(FEATURE_RX_PARALLEL_PWM);
featureClear(FEATURE_RX_PPM);
}
if (featureConfigured(FEATURE_RX_SERIAL)) {
featureClear(FEATURE_RX_PARALLEL_PWM);
featureClear(FEATURE_RX_PPM);
}
if (featureConfigured(FEATURE_RX_PARALLEL_PWM)) {
#if defined(STM32F10X)
// rssi adc needs the same ports
featureClear(FEATURE_RSSI_ADC);
// current meter needs the same ports
if (masterConfig.batteryConfig.currentMeterType == CURRENT_SENSOR_ADC) {
featureClear(FEATURE_CURRENT_METER);
}
#endif
#if defined(STM32F10X) || defined(CHEBUZZ) || defined(STM32F3DISCOVERY)
// led strip needs the same ports
featureClear(FEATURE_LED_STRIP);
#endif
// software serial needs free PWM ports
featureClear(FEATURE_SOFTSERIAL);
}
#if defined(LED_STRIP) && (defined(USE_SOFTSERIAL1) || defined(USE_SOFTSERIAL2))
if (featureConfigured(FEATURE_SOFTSERIAL) && (
0
#ifdef USE_SOFTSERIAL1
|| (WS2811_TIMER == SOFTSERIAL_1_TIMER)
#endif
#ifdef USE_SOFTSERIAL2
|| (WS2811_TIMER == SOFTSERIAL_2_TIMER)
#endif
)) {
// led strip needs the same timer as softserial
featureClear(FEATURE_LED_STRIP);
}
#endif
#if defined(NAZE) && defined(SONAR)
if (featureConfigured(FEATURE_RX_PARALLEL_PWM) && featureConfigured(FEATURE_SONAR) && featureConfigured(FEATURE_CURRENT_METER) && masterConfig.batteryConfig.currentMeterType == CURRENT_SENSOR_ADC) {
featureClear(FEATURE_CURRENT_METER);
}
#endif
#if defined(OLIMEXINO) && defined(SONAR)
if (feature(FEATURE_SONAR) && feature(FEATURE_CURRENT_METER) && masterConfig.batteryConfig.currentMeterType == CURRENT_SENSOR_ADC) {
featureClear(FEATURE_CURRENT_METER);
}
#endif
#if defined(CC3D) && defined(DISPLAY) && defined(USE_UART3)
if (doesConfigurationUsePort(SERIAL_PORT_USART3) && feature(FEATURE_DISPLAY)) {
featureClear(FEATURE_DISPLAY);
}
#endif
/*#if defined(LED_STRIP) && defined(TRANSPONDER) // TODO - Add transponder feature
if ((WS2811_DMA_TC_FLAG == TRANSPONDER_DMA_TC_FLAG) && featureConfigured(FEATURE_TRANSPONDER) && featureConfigured(FEATURE_LED_STRIP)) {
featureClear(FEATURE_LED_STRIP);
}
#endif
*/
#if defined(CC3D) && defined(SONAR) && defined(USE_SOFTSERIAL1) && defined(RSSI_ADC_GPIO)
// shared pin
if ((featureConfigured(FEATURE_SONAR) + featureConfigured(FEATURE_SOFTSERIAL) + featureConfigured(FEATURE_RSSI_ADC)) > 1) {
featureClear(FEATURE_SONAR);
featureClear(FEATURE_SOFTSERIAL);
featureClear(FEATURE_RSSI_ADC);
}
#endif
#if defined(COLIBRI_RACE)
masterConfig.serialConfig.portConfigs[0].functionMask = FUNCTION_MSP;
if (featureConfigured(FEATURE_RX_PARALLEL_PWM) || featureConfigured(FEATURE_RX_MSP)) {
featureClear(FEATURE_RX_PARALLEL_PWM);
featureClear(FEATURE_RX_MSP);
featureSet(FEATURE_RX_PPM);
}
#endif
useRxConfig(&masterConfig.rxConfig);
serialConfig_t *serialConfig = &masterConfig.serialConfig;
if (!isSerialConfigValid(serialConfig)) {
resetSerialConfig(serialConfig);
}
}
void validateAndFixConfig(void)
{
if (!(featureConfigured(FEATURE_RX_PARALLEL_PWM) || featureConfigured(FEATURE_RX_PPM) || featureConfigured(FEATURE_RX_SERIAL) || featureConfigured(FEATURE_RX_MSP))) {
featureSet(DEFAULT_RX_FEATURE);
}
if (featureConfigured(FEATURE_RX_PPM)) {
featureClear(FEATURE_RX_PARALLEL_PWM | FEATURE_RX_SERIAL | FEATURE_RX_MSP);
}
if (featureConfigured(FEATURE_RX_MSP)) {
featureClear(FEATURE_RX_SERIAL | FEATURE_RX_PARALLEL_PWM | FEATURE_RX_PPM);
}
if (featureConfigured(FEATURE_RX_SERIAL)) {
featureClear(FEATURE_RX_PARALLEL_PWM | FEATURE_RX_MSP | FEATURE_RX_PPM);
}
if (featureConfigured(FEATURE_RX_PARALLEL_PWM)) {
featureClear(FEATURE_RX_SERIAL | FEATURE_RX_MSP | FEATURE_RX_PPM);
}
#if defined(LED_STRIP) && (defined(USE_SOFTSERIAL1) || defined(USE_SOFTSERIAL2))
if (featureConfigured(FEATURE_SOFTSERIAL) && (
0
#ifdef USE_SOFTSERIAL1
|| (LED_STRIP_TIMER == SOFTSERIAL_1_TIMER)
#endif
#ifdef USE_SOFTSERIAL2
|| (LED_STRIP_TIMER == SOFTSERIAL_2_TIMER)
#endif
)) {
// led strip needs the same timer as softserial
featureClear(FEATURE_LED_STRIP);
}
#endif
#if defined(CC3D) && defined(DISPLAY) && defined(USE_UART3)
if (doesConfigurationUsePort(SERIAL_PORT_UART3) && featureConfigured(FEATURE_DISPLAY)) {
featureClear(FEATURE_DISPLAY);
}
#endif
#ifdef STM32F303xC
// hardware supports serial port inversion, make users life easier for those that want to connect SBus RX's
#ifdef TELEMETRY
masterConfig.telemetryConfig.telemetry_inversion = 1;
#endif
#endif
/*
* The retarded_arm setting is incompatible with pid_at_min_throttle because full roll causes the craft to roll over on the ground.
* The pid_at_min_throttle implementation ignores yaw on the ground, but doesn't currently ignore roll when retarded_arm is enabled.
*/
if (masterConfig.retarded_arm && masterConfig.mixerConfig.pid_at_min_throttle) {
masterConfig.mixerConfig.pid_at_min_throttle = 0;
}
#if defined(LED_STRIP) && defined(TRANSPONDER) && !defined(UNIT_TEST)
if ((WS2811_DMA_TC_FLAG == TRANSPONDER_DMA_TC_FLAG) && featureConfigured(FEATURE_TRANSPONDER) && featureConfigured(FEATURE_LED_STRIP)) {
featureClear(FEATURE_LED_STRIP);
}
#endif
#if defined(CC3D) && defined(SONAR) && defined(USE_SOFTSERIAL1)
if (featureConfigured(FEATURE_SONAR) && featureConfigured(FEATURE_SOFTSERIAL)) {
featureClear(FEATURE_SONAR);
}
#endif
#if defined(COLIBRI_RACE)
masterConfig.serialConfig.portConfigs[0].functionMask = FUNCTION_MSP;
if(featureConfigured(FEATURE_RX_SERIAL)) {
masterConfig.serialConfig.portConfigs[2].functionMask = FUNCTION_RX_SERIAL;
}
#endif
useRxConfig(&masterConfig.rxConfig);
serialConfig_t *serialConfig = &masterConfig.serialConfig;
if (!isSerialConfigValid(serialConfig)) {
resetSerialConfig(serialConfig);
}
}