void initialiseIO()
{
//Led Fault
mPORTBSetPinsDigitalOut(BIT_8);
PORTSetBits(IOPORT_B, BIT_8);
//Led Alert
mPORTBSetPinsDigitalOut(BIT_9);
PORTSetBits(IOPORT_B, BIT_9);
//Relais 1
mPORTDSetPinsDigitalOut(BIT_1);
PORTSetBits(IOPORT_D, BIT_1);
//Relais 2
mPORTDSetPinsDigitalOut(BIT_2);
PORTSetBits(IOPORT_D, BIT_2);
//Address
mPORTESetPinsDigitalIn(BIT_0);
mPORTESetPinsDigitalIn(BIT_1);
mPORTESetPinsDigitalIn(BIT_2);
mPORTESetPinsDigitalIn(BIT_3);
mPORTESetPinsDigitalIn(BIT_4);
mPORTESetPinsDigitalIn(BIT_5);
mPORTESetPinsDigitalIn(BIT_6);
mPORTESetPinsDigitalIn(BIT_7);
}
/****************************************************************************
Function:
static void InitializeBoard(void)
Description:
This routine initializes the hardware. It is a generic initialization
routine for many of the Microchip development boards, using definitions
in HardwareProfile.h to determine specific initialization.
Precondition:
None
Parameters:
None - None
Returns:
None
Remarks:
None
***************************************************************************/
static void InitializeBoard(void) {
// WiFi Module hardware Initialization handled by Library
// Enable multi-vectored interrupts
INTEnableSystemMultiVectoredInt();
// Enable optimal performance
SYSTEMConfigPerformance(GetSystemClock());
mOSCSetPBDIV(OSC_PB_DIV_1); // Use 1:1 CPU Core:Peripheral clocks
// Disable JTAG port so we get our I/O pins back, but first
// wait 50ms so if you want to reprogram the part with
// JTAG, you'll still have a tiny window before JTAG goes away.
// The PIC32 Starter Kit debuggers use JTAG and therefore must not
// disable JTAG.
DelayMs(50);
DDPCONbits.JTAGEN = 0;
// LEDs
LEDS_OFF();
mPORTESetPinsDigitalOut(BIT_5 | BIT_6 | BIT_7);
// Switches
mPORTDSetPinsDigitalIn(BIT_4 | BIT_5 | BIT_6);
ConfigCNPullups(CN13_PULLUP_ENABLE | CN14_PULLUP_ENABLE | CN15_PULLUP_ENABLE);
// LCD
mPORTESetPinsDigitalOut(BIT_0 | BIT_1 | BIT_2 | BIT_3);
//Configure LCD SPI pins
mPORTFSetPinsDigitalOut(BIT_8);
mPORTDSetPinsDigitalOut(BIT_15);
//SPI Flash
mPORTDSetPinsDigitalOut(BIT_14);
//UART
mPORTFSetPinsDigitalOut(BIT_5);
mPORTFSetPinsDigitalIn(BIT_4);
//MiWi
#if defined(MRF24J40) || defined(MRF49XA)
PHY_CS = 1;
mPORTDSetPinsDigitalOut(BIT_9);
PHY_RESETn = 1;
mPORTDSetPinsDigitalOut(BIT_11);
#endif
#if defined(MRF49XA)
nFSEL_TRIS = 0;
FINT_TRIS = 1;
nFSEL = 1;
#elif defined(MRF24J40)
PHY_WAKE = 1;
mPORTBSetPinsDigitalOut(BIT_9);
#else
Data_nCS_TRIS = 0;
Config_nCS_TRIS = 0;
Data_nCS = 1;
Config_nCS = 1;
IRQ1_INT_TRIS = 1;
IRQ0_INT_TRIS = 1;
#endif
/* Set the Port Directions of SDO, SDI, Clock & Slave Select Signal */
/* Set SCK port pin to output */
mPORTDSetPinsDigitalOut(BIT_10);
/* Set SDO port pin to output */
mPORTDSetPinsDigitalOut(BIT_0);
/* Set SDI port pin to input */
mPORTCSetPinsDigitalIn(BIT_4);
/* Set INT1, INT2 port pins to input */
mPORTESetPinsDigitalIn(BIT_8 | BIT_9);
/* Clear SPI1CON register */
SPI1CONCLR = 0xFFFFFFFF;
#ifdef HARDWARE_SPI
unsigned int pbFreq;
/* Enable SPI1, Set to Master Mode & Set CKE bit : Serial output data changes on transition
from active clock state to Idle clock state */
SPI1CON = 0x00008120;
/* Peripheral Bus Frequency = System Clock / PB Divider */
pbFreq = (DWORD) CLOCK_FREQ / (1 << mOSCGetPBDIV());
/* PB Frequency can be maximum 40 MHz */
if (pbFreq > (2 * MAX_SPI_CLK_FREQ_FOR_P2P)) {
{
unsigned int SPI_Clk_Freq;
unsigned char SPI_Brg1 = 1;
//For the SPI1
/* Continue the loop till you find SPI Baud Rate Register Value */
while (1) {
/* SPI Clock Calculation as per PIC32 Manual */
SPI_Clk_Freq = pbFreq / (2 * (SPI_Brg1 + 1));
if (SPI_Clk_Freq <= MAX_SPI_CLK_FREQ_FOR_P2P) {
break;
}
SPI_Brg1++;
}
mSpiChnSetBrg(1, SPI_Brg1);
}
} else {
/* Set SPI1 Baud Rate */
mSpiChnSetBrg(1, 0);
}
#endif
/* Set the Interrupt Priority */
mINT2SetIntPriority(4);
#if defined(MRF89XA)
mINT1SetIntPriority(4);
#endif
/* Set Interrupt Subpriority Bits for INT2 */
mINT2SetIntSubPriority(2);
#if defined(MRF89XA)
mINT2SetIntSubPriority(1);
#endif
/* Set INT2 to falling edge */
mINT2SetEdgeMode(0);
#if defined(MRF89XA)
mINT1SetEdgeMode(1);
mINT2SetEdgeMode(1);
#endif
/* Enable INT2 */
mINT2IntEnable(1);
#if defined(MRF89XA)
mINT2IntEnable(1);
#endif
/* Enable Multi Vectored Interrupts */
// INTEnableSystemMultiVectoredInt();
#if defined(MRF89XA)
PHY_IRQ1 = 0;
PHY_IRQ0 = 0;
PHY_RESETn_TRIS = 1;
#else
RFIF = 0;
if (RF_INT_PIN == 0) {
RFIF = 1;
}
#endif
// Initialize the EEPROM
XEEInit();
// UART Initialization
#if defined(STACK_USE_UART)
UARTTX_TRIS = 0;
UARTRX_TRIS = 1;
UMODE = 0x8000; // Set UARTEN. Note: this must be done before setting UTXEN
USTA = 0x00001400; // RXEN set, TXEN set
#define CLOSEST_UBRG_VALUE ((GetPeripheralClock()+8ul*BAUD_RATE)/16/BAUD_RATE-1)
#define BAUD_ACTUAL (GetPeripheralClock()/16/(CLOSEST_UBRG_VALUE+1))
#define BAUD_ERROR ((BAUD_ACTUAL > BAUD_RATE) ? BAUD_ACTUAL-BAUD_RATE : BAUD_RATE-BAUD_ACTUAL)
#define BAUD_ERROR_PRECENT ((BAUD_ERROR*100+BAUD_RATE/2)/BAUD_RATE)
#if (BAUD_ERROR_PRECENT > 3)
#warning UART frequency error is worse than 3%
#elif (BAUD_ERROR_PRECENT > 2)
#warning UART frequency error is worse than 2%
#endif
UBRG = CLOSEST_UBRG_VALUE;
#endif
}
/*******************************************************************************
* Function: BoardInit(void)
* PreCondition:None
* Input: None
* Output: None
* Overview: SPI pins and SFR, Maintenance Tasks Timer, External Interrupts,
* and other board issues initialization.
* Note: This routine needs to be called before initialising MiWi stack
* or invoking other function that operates on MiWi stack.
******************************************************************************/
void BoardInit(void){
#if defined(__PIC32MX__)
// RADIO INTERFACES & SPI INIT -------------------------------------------//
#if defined HARDWARE_SPI
/* Peripheral Bus Frequency = System Clock / PB Divider */
unsigned int pbFreq;
pbFreq = (DWORD) CLOCK_FREQ/(1 << mOSCGetPBDIV());
unsigned int SPI_Clk_Freq;
unsigned char SPI_Brg;
#endif
#if defined MRF24J40
PHY_CS_TRIS = 0;
PHY_CS = 1;
PHY_RESETn_TRIS = 0;
PHY_RESETn = 1;
MRF24J40_INT_TRIS = 1;
SDI_TRIS = 1;
SDO_TRIS = 0;
SCK_TRIS = 0;
SPI_SDO = 0;
SPI_SCK = 0;
PHY_WAKE_TRIS = 0;
PHY_WAKE = 1;
SPICONCLR = 0xFFFFFFFF; // Clear SPIxCON register
#ifdef HARDWARE_SPI
/* Enable SPI, Set to Master Mode & Set CKE bit : Serial output
* data changes on transition from active clock state to Idle
* clock state */
SPICON = 0x00008120;
/* PB Frequency can be maximum 40 MHz */
if(pbFreq > (2 * MAX_SPI_CLK_FREQ_FOR_P2P)){
SPI_Brg = 1;
/* Continue the loop till you find SPI Baud Rate Reg Value */
while(1){
/* SPI Clock Calculation as per PIC32 Manual */
SPI_Clk_Freq = pbFreq / (2 * (SPI_Brg + 1));
if(SPI_Clk_Freq <= MAX_SPI_CLK_FREQ_FOR_P2P){
break;
}
SPI_Brg++;
}
#if defined MRF24J40_IN_SPI1
mSpiChnSetBrg (1, SPI_Brg);
#elif defined MRF24J40_IN_SPI2
mSpiChnSetBrg (2, SPI_Brg);
#elif defined MRF24J40_IN_SPI3
mSpiChnSetBrg (1A, SPI_Brg);
#elif defined MRF24J40_IN_SPI4
mSpiChnSetBrg (3A, SPI_Brg);
#endif
}
else{
#if defined MRF24J40_IN_SPI1
mSpiChnSetBrg (1, 0);
#elif defined MRF24J40_IN_SPI2
mSpiChnSetBrg (2, 0);
#elif defined MRF24J40_IN_SPI3
mSpiChnSetBrg (1A, 0);
#elif defined MRF24J40_IN_SPI4
mSpiChnSetBrg (3A, SPI_Brg);
#endif
}
#endif
#endif
#if defined(MRF49XA_1)
//Configuration for Guilja's Expansion Board, Connection SLot 1 --//
mPORTESetPinsDigitalOut(BIT_1); //nCS
mPORTBSetPinsDigitalIn(BIT_2); //FINT //Juan: Added.
//----------------------------------------------------------------//
MRF49XA_1_PHY_CS_TRIS = 0;
MRF49XA_1_PHY_CS = 1;
MRF49XA_1_PHY_RESETn_TRIS = 0;
MRF49XA_1_PHY_RESETn = 1;
MRF49XA_1_INT_TRIS = 1;
MRF49XA_1_SDI_TRIS = 1;
MRF49XA_1_SDO_TRIS = 0;
MRF49XA_1_SCK_TRIS = 0;
MRF49XA_1_SPI_SDO = 0;
MRF49XA_1_SPI_SCK = 0;
MRF49XA_1_nFSEL_TRIS = 0;
MRF49XA_1_FINT_TRIS = 1;
MRF49XA_1_nFSEL = 1; // nFSEL inactive
MRF49XA_1_SPICONCLR = 0xFFFFFFFF; //Clear SPIxCON register
#ifdef HARDWARE_SPI
/* Enable SPI1, Set to Master Mode & Set CKE bit : Serial output
* data changes on transition from active clock state to Idle
* clock state */
MRF49XA_1_SPICON = 0x00008120;
/* PB Frequency can be maximum 40 MHz */
if(pbFreq > (2 * MAX_SPI_CLK_FREQ_FOR_P2P)){
SPI_Brg = 1;
/* Continue the loop till you find SPI Baud Rate Reg Value */
while(1){
/* SPI Clock Calculation as per PIC32 Manual */
SPI_Clk_Freq = pbFreq / (2 * (SPI_Brg + 1));
if(SPI_Clk_Freq <= MAX_SPI_CLK_FREQ_FOR_P2P){
break;
}
SPI_Brg++;
}
#if defined MRF49XA_1_IN_SPI1
mSpiChnSetBrg (1, SPI_Brg);
#elif defined MRF49XA_1_IN_SPI2
mSpiChnSetBrg (2, SPI_Brg);
#elif defined MRF49XA_1_IN_SPI3
mSpiChnSetBrg (1A, SPI_Brg);
#endif
}
else{
#if defined MRF49XA_1_IN_SPI1
mSpiChnSetBrg (1, 0);
#elif defined MRF49XA_1_IN_SPI2
mSpiChnSetBrg (2, 0);
#elif defined MRF49XA_1_IN_SPI3
mSpiChnSetBrg (1A, 0);
#endif
}
#endif
#endif
#if defined(MRF49XA_2)
MRF49XA_2_PHY_CS_TRIS = 0;
MRF49XA_2_PHY_CS = 1;
MRF49XA_2_PHY_RESETn_TRIS = 0;
MRF49XA_2_PHY_RESETn = 1;
MRF49XA_2_INT_TRIS = 1;
MRF49XA_2_SDI_TRIS = 1;
MRF49XA_2_SDO_TRIS = 0;
MRF49XA_2_SCK_TRIS = 0;
MRF49XA_2_SPI_SDO = 0;
MRF49XA_2_SPI_SCK = 0;
MRF49XA_2_nFSEL_TRIS = 0;
MRF49XA_2_FINT_TRIS = 1;
MRF49XA_2_nFSEL = 1; // nFSEL inactive
MRF49XA_2_SPICONCLR = 0xFFFFFFFF; // Clear SPIxCON register
#ifdef HARDWARE_SPI
/* Enable SPI1, Set to Master Mode & Set CKE bit : Serial output
* data changes on transition from active clock state to Idle
* clock state */
MRF49XA_2_SPICON = 0x00008120;
/* PB Frequency can be maximum 40 MHz */
if(pbFreq > (2 * MAX_SPI_CLK_FREQ_FOR_P2P)){
SPI_Brg = 1;
/* Continue the loop till you find SPI Baud Rate Reg Value */
while(1){
/* SPI Clock Calculation as per PIC32 Manual */
SPI_Clk_Freq = pbFreq / (2 * (SPI_Brg + 1));
if(SPI_Clk_Freq <= MAX_SPI_CLK_FREQ_FOR_P2P){
break;
}
SPI_Brg++;
}
#if defined MRF49XA_2_IN_SPI1
mSpiChnSetBrg (1, SPI_Brg);
#elif defined MRF49XA_2_IN_SPI2
mSpiChnSetBrg (2, SPI_Brg);
#elif defined MRF49XA_2_IN_SPI3
mSpiChnSetBrg (1A, SPI_Brg);
#endif
}
else{
#if defined MRF49XA_2_IN_SPI1
mSpiChnSetBrg (1, 0);
#elif defined MRF49XA_2_IN_SPI2
mSpiChnSetBrg (2, 0);
#elif defined MRF49XA_2_IN_SPI3
mSpiChnSetBrg (1A, 0);
#endif
}
#endif
#endif
#if defined MRF89XA
Data_nCS_TRIS = 0;
Config_nCS_TRIS = 0;
Data_nCS = 1;
Config_nCS = 1;
PHY_IRQ1_TRIS = 1;
//... REVIEW...
#endif
// SPI & EXTERNAL INTERRUPTS PINS AND CONFIGURATION ----------------------//
#if defined (__32MX795F512L__) || defined __32MX675F256L__
/* Set the SPI Port Directions (SDO, SDI, SCK) for every SPI module.*/
#if defined MRF49XA_1_IN_SPI1 || defined MRF49XA_2_IN_SPI1 || \
defined MRF89XA_IN_SPI1 || defined MRF24J40_IN_SPI1 || \
defined MRF24WB0M_IN_SPI1
mPORTDSetPinsDigitalOut(BIT_0); //SDO1
mPORTDSetPinsDigitalOut(BIT_10); //SCK1
mPORTCSetPinsDigitalIn(BIT_4); //SDI1
#endif
#if defined MRF49XA_1_IN_SPI2 || defined MRF49XA_2_IN_SPI2 || \
defined MRF89XA_IN_SPI2 || defined MRF24J40_IN_SPI2 || \
defined MRF24WB0M_IN_SPI2
mPORTGSetPinsDigitalOut(BIT_8); //SDO2
mPORTGSetPinsDigitalOut(BIT_6); //SCK2
mPORTGSetPinsDigitalIn(BIT_7); //SDI2
#endif
#if defined MRF49XA_1_IN_SPI3 || defined MRF49XA_2_IN_SPI3 || \
defined MRF89XA_IN_SPI3 || defined MRF24J40_IN_SPI3 || \
defined MRF24WB0M_IN_SPI3
mPORTFSetPinsDigitalOut(BIT_8); //SDO3
mPORTDSetPinsDigitalOut(BIT_15); //SCK3
mPORTFSetPinsDigitalIn(BIT_2); //SDI3
#endif
#if defined MRF49XA_1_IN_SPI4 || defined MRF49XA_2_IN_SPI4 || \
defined MRF89XA_IN_SPI4 || defined MRF24J40_IN_SPI4 || \
defined MRF24WB0M_IN_SPI4
mPORTFSetPinsDigitalOut(BIT_5); //SDO4
mPORTFSetPinsDigitalOut(BIT_13); //SCK4
mPORTFSetPinsDigitalIn(BIT_4); //SDI4
#endif
#elif defined (__32MX795F512H__)
#if defined MRF49XA_1_IN_SPI2 || defined MRF49XA_2_IN_SPI2 || \
defined MRF89XA_IN_SPI2 || defined MRF24J40_IN_SPI2 || \
defined MRF24WB0M_IN_SPI2
mPORTGSetPinsDigitalOut(BIT_8); //SDO2
mPORTGSetPinsDigitalOut(BIT_6); //SCK2
mPORTGSetPinsDigitalIn(BIT_7); //SDI2
#endif
#if defined MRF49XA_1_IN_SPI3 || defined MRF49XA_2_IN_SPI3 || \
defined MRF89XA_IN_SPI3 || defined MRF24J40_IN_SPI3 || \
defined MRF24WB0M_IN_SPI3
mPORTDSetPinsDigitalOut(BIT_3); //SDO3
mPORTDSetPinsDigitalOut(BIT_1); //SCK3
mPORTDSetPinsDigitalIn(BIT_2); //SDI3
#endif
#if defined MRF24J40_IN_SPI4 || defined MRF24WB0M_IN_SPI4
mPORTFSetPinsDigitalOut(BIT_5); //SDO4
mPORTBSetPinsDigitalOut(BIT_14); //SCK4
mPORTFSetPinsDigitalIn(BIT_4); //SDI4
#endif
#endif
#if defined (__32MX795F512L__) || defined __32MX675F256L__
/* Set the external interrups Pin Directions and Priority*/
#if defined MRF49XA_1_USES_INT1 || defined MRF49XA_2_USES_INT1 || \
defined MRF89XA_USES_INT1 || defined MRF24J40_USES_INT1 || \
defined MRF24WB0M_USES_INT1
mPORTESetPinsDigitalIn(BIT_8);
mINT1SetIntPriority(4);
mINT1SetIntSubPriority(2);
mINT1SetEdgeMode(0); //0: Falling Edge.
/* Enable INT1 */
mINT1IntEnable(1);
#endif
#if defined MRF49XA_1_USES_INT2 || defined MRF49XA_2_USES_INT2 || \
defined MRF89XA_USES_INT2 || defined MRF24J40_USES_INT2 || \
defined MRF24WB0M_USES_INT2
mPORTESetPinsDigitalIn(BIT_9);
mINT2SetIntPriority(4);
mINT2SetIntSubPriority(2);
mINT2SetEdgeMode(0); //0: Falling Edge.
/* Enable INT2 */
mINT2IntEnable(1);
#endif
#if defined MRF49XA_1_USES_INT3 || defined MRF49XA_2_USES_INT3 || \
defined MRF89XA_USES_INT3 || defined MRF24J40_USES_INT3 || \
defined MRF24WB0M_USES_INT3
mPORTASetPinsDigitalIn(BIT_14);
mINT3SetIntPriority(4);
mINT3SetIntSubPriority(2);
mINT3SetEdgeMode(0); //0: Falling Edge.
/* Enable INT3 */
mINT3IntEnable(1);
#endif
#if defined MRF49XA_1_USES_INT4 || defined MRF49XA_2_USES_INT4 || \
defined MRF89XA_USES_INT4 || defined MRF24J40_USES_INT4 || \
defined MRF24WB0M_USES_INT4
mPORTASetPinsDigitalIn(BIT_15);
mINT4SetIntPriority(4);
mINT4SetIntSubPriority(2);
mINT4SetEdgeMode(0); //0: Falling Edge.
/* Enable INT4 */
mINT4IntEnable(1);
#endif
#elif defined (__32MX795F512H__)
#if defined MRF49XA_1_USES_INT1 || defined MRF49XA_2_USES_INT1 || \
defined MRF89XA_USES_INT1 || defined MRF24J40_USES_INT1 || \
defined MRF24WB0M_USES_INT1
mPORTDSetPinsDigitalIn(BIT_8);
mINT1SetIntPriority(4);
mINT1SetIntSubPriority(2);
mINT1SetEdgeMode(0); //0: Falling Edge.
/* Enable INT1 */
mINT1IntEnable(1);
#endif
#if defined MRF49XA_1_USES_INT2 || defined MRF49XA_2_USES_INT2 || \
defined MRF89XA_USES_INT2 || defined MRF24J40_USES_INT2 || \
defined MRF24WB0M_USES_INT2
mPORTDSetPinsDigitalIn(BIT_9); //Warning. Shared with SPI3 nSS3
mINT2SetIntPriority(4);
mINT2SetIntSubPriority(2);
mINT2SetEdgeMode(0); //0: Falling Edge.
/* Enable INT2 */
mINT2IntEnable(1);
#endif
#if defined MRF49XA_1_USES_INT3 || defined MRF49XA_2_USES_INT3 || \
defined MRF89XA_USES_INT3 || defined MRF24J40_USES_INT3 || \
defined MRF24WB0M_USES_INT3
mPORTDSetPinsDigitalIn(BIT_10);
mINT3SetIntPriority(4);
mINT3SetIntSubPriority(2);
mINT3SetEdgeMode(0); //0: Falling Edge.
/* Enable INT3 */
mINT3IntEnable(1);
#endif
#if defined MRF49XA_1_USES_INT4 || defined MRF49XA_2_USES_INT4 || \
defined MRF89XA_USES_INT4 || defined MRF24J40_USES_INT4 || \
defined MRF24WB0M_USES_INT4
mPORTDSetPinsDigitalIn(BIT_11);
mINT4SetIntPriority(4);
mINT4SetIntSubPriority(2);
mINT4SetEdgeMode(0); //0: Falling Edge.
/* Enable INT4 */
mINT4IntEnable(1);
#endif
#endif
// TIMER 1 FOR TIME_SYNC -------------------------------------------------//
#if defined(ENABLE_TIME_SYNC)
//TIMER 1 MAY BE USED FOR SLEEP MODE AND/OR FOR STACKS MAINTENANCE. IT
//NEEDS ADAPTATION BEFORE ENABLING TIME_SYNC WITH TIMER 1 TOO!
T1CON = 0;
T1CON = 0x0012;
T1CONSET = 0x8000;
PR1 = 0xFFFF;
IFS0bits.T1IF = 0;
mT1IntEnable(1);
mT1SetIntPriority(4);
while(T1CONbits.TWIP);
TMR1 = 0;
#endif
// TIMER 1 FOR NODE STACKS AUTO-MAINTENANCE ------------------------------//
#if defined NODE_DOES_MAINTENANCE_TASKS
T1CON = 0x0070; //Disable timer, PBCLK source, PS=256
TMR1 = 0x0000; //Reset count
PR1 = MAINTENANCE_PERIOD; //Set period.
IPC1SET = 0x00000005; //Set Priority level 1, Subpriority level 1
IFS0CLR = 0x00000010; //Clear T1IF
IEC0SET = 0x00000010; //Set T1IE
//Timer will be triggered after initialization.
#endif
// IOPORT CN - For waking up the node manually. --------------------------//
mPORTDSetPinsDigitalIn(BIT_5); // CN14
CNCON = 0x8000; //Module enabled.
CNEN = 0x00004000; //Enable CN14
CNPUE = 0x00004000; //Enable CN14 weak pull-up.
//ReadBUTTONS(); //Clear PORT mismatch condition.
IFS1CLR = 0x00000001; //Clear the CN interrupt flag status bit
IPC6SET = 0x00180000; //Set CN priority 6, subpriority 0.
//It will be enabled only during sleep mode time interval
//------------------------------------------------------------------------//
//JUAN: NVM NOT ADAPTED FOR LSI-CWSN MIWI STACK // Lo modifico en el wifi config
#if defined(ENABLE_NVM)
//EE_nCS_TRIS = 0;
//EE_nCS = 1;
#endif
// INTERRUPTION FLAGS AND EXT_INT PIN FINAL SETTINGS ---------------------//
#if defined MRF49XA_1
MRF49XA_1_IF = 0;
if(MRF49XA_1_INT_PIN == 0){
MRF49XA_1_IF = 1;
}
#endif
#if defined MRF49XA_2
MRF49XA_2_IF = 0;
if(MRF49XA_2_INT_PIN == 0){
MRF49XA_2_IF = 1;
}
#endif
#if defined MRF89XA
PHY_IRQ1 = 0;
#endif
#if defined MRF24J40
MRF24J40_IF = 0;
if(MRF24J40_INT_PIN == 0){
MRF24J40_IF = 1;
}
#endif
#else //Not PIC32.
#error "Unknown target board."
#endif
}
//********************************
//********************************
//********** INITIALISE **********
//********************************
//********************************
void initialise (void)
{
BYTE data;
//##### GENERAL NOTE ABOUT PIC32'S #####
//Try and use the peripheral libraries instead of special function registers for everything (literally everything!) to avoid
//bugs that can be caused by the pipeline and interrupts.
//---------------------------------
//----- CONFIGURE PERFORMANCE -----
//---------------------------------
//----- SETUP EVERYTHING FOR OPTIMUM PERFORMANCE -----
SYSTEMConfigPerformance(80000000ul); //Note this sets peripheral bus to '1' max speed (regardless of configuration bit setting)
//Use PBCLK divider of 1:1 to calculate UART baud, timer tick etc
//----- SET PERIPHERAL BUS DIVISOR -----
//To minimize dynamic power the PB divisor should be chosen to run the peripherals at the lowest frequency that provides acceptable system performance
mOSCSetPBDIV(OSC_PB_DIV_2); //OSC_PB_DIV_1, OSC_PB_DIV_2, OSC_PB_DIV_4, OSC_PB_DIV_8,
//----- SETUP INTERRUPTS -----
INTEnableSystemMultiVectoredInt();
//-------------------------
//----- SETUP IO PINS -----
//-------------------------
//(Device will powerup with all IO pins as inputs)
//----- TURN OFF THE JTAG PORT -----
//(JTAG is on by default)
//mJTAGPortEnable(0); //Must be on for Microchip Multimedia Development board
#define PORTA_IO 0xc2ff //Setup the IO pin type (0 = output, 1 = input)
mPORTAWrite(0xc033); //Set initial ouput pin states
mPORTASetPinsDigitalIn(PORTA_IO); //(Sets high bits as input)
mPORTASetPinsDigitalOut(~PORTA_IO); //(Sets high bits as output)
#define PORTB_IO 0xfbff //Setup the IO pin type (0 = output, 1 = input)
mPORTBWrite(0x6d13); //Set initial ouput pin states
mPORTBSetPinsDigitalIn(PORTB_IO); //(Sets high bits as input)
mPORTBSetPinsDigitalOut(~PORTB_IO); //(Sets high bits as output)
mPORTBSetPinsDigitalIn(BIT_0 | BIT_1 | BIT_3 | BIT_4 | BIT_15); //Joystick inputs
#define PORTC_IO 0xf01e //Setup the IO pin type (0 = output, 1 = input)
mPORTCWrite(0x3018); //Set initial ouput pin states
mPORTCSetPinsDigitalIn(PORTC_IO); //(Sets high bits as input)
mPORTCSetPinsDigitalOut(~PORTC_IO); //(Sets high bits as output)
#define PORTD_IO 0x7bfe //Setup the IO pin type (0 = output, 1 = input)
mPORTDWrite(0xbdaf); //Set initial ouput pin states
mPORTDSetPinsDigitalIn(PORTD_IO); //(Sets high bits as input)
mPORTDSetPinsDigitalOut(~PORTD_IO); //(Sets high bits as output)
mPORTDSetPinsDigitalOut(BIT_2 | BIT_1); //LED's 2 and 3
mPORTDSetPinsDigitalIn(BIT_9);
#define PORTE_IO 0x03ff //Setup the IO pin type (0 = output, 1 = input)
mPORTEWrite(0x02a2); //Set initial ouput pin states
mPORTESetPinsDigitalIn(PORTE_IO); //(Sets high bits as input)
mPORTESetPinsDigitalOut(~PORTE_IO); //(Sets high bits as output)
#define PORTF_IO 0x111f //Setup the IO pin type (0 = output, 1 = input)
mPORTFWrite(0x0039); //Set initial ouput pin states
mPORTFSetPinsDigitalIn(PORTF_IO); //(Sets high bits as input)
mPORTFSetPinsDigitalOut(~PORTF_IO); //(Sets high bits as output)
#define PORTG_IO 0xd3cf //Setup the IO pin type (0 = output, 1 = input)
mPORTGWrite(0xf203); //Set initial ouput pin states
mPORTGSetPinsDigitalIn(PORTG_IO); //(Sets high bits as input)
mPORTGSetPinsDigitalOut(~PORTG_IO); //(Sets high bits as output)
//Read pins using:
// mPORTAReadBits(BIT_0);
//Write pins using:
// mPORTAClearBits(BIT_0);
// mPORTASetBits(BIT_0);
// mPORTAToggleBits(BIT_0);
//----- INPUT CHANGE NOTIFICATION CONFIGURATION -----
//EnableCN0();
ConfigCNPullups(CN2_PULLUP_ENABLE | CN3_PULLUP_ENABLE | CN5_PULLUP_ENABLE | CN6_PULLUP_ENABLE | CN12_PULLUP_ENABLE); //Joystick pins
//----- SETUP THE A TO D PINS -----
ENABLE_ALL_DIG;
//---------------------
//----- SETUP USB -----
//---------------------
//The USB specifications require that USB peripheral devices must never source current onto the Vbus pin. Additionally, USB peripherals should not source
//current on D+ or D- when the host/hub is not actively powering the Vbus line. When designing a self powered (as opposed to bus powered) USB peripheral
//device, the firmware should make sure not to turn on the USB module and D+ or D- pull up resistor unless Vbus is actively powered. Therefore, the
//firmware needs some means to detect when Vbus is being powered by the host. A 5V tolerant I/O pin can be connected to Vbus (through a resistor), and
//can be used to detect when Vbus is high (host actively powering), or low (host is shut down or otherwise not supplying power). The USB firmware
//can then periodically poll this I/O pin to know when it is okay to turn on the USB module/D+/D- pull up resistor. When designing a purely bus powered
//peripheral device, it is not possible to source current on D+ or D- when the host is not actively providing power on Vbus. Therefore, implementing this
//bus sense feature is optional. This firmware can be made to use this bus sense feature by making sure "USE_USB_BUS_SENSE_IO" has been defined in the
//HardwareProfile.h file.
// #if defined(USE_USB_BUS_SENSE_IO)
// tris_usb_bus_sense = INPUT_PIN; // See HardwareProfile.h
// #endif
//If the host PC sends a GetStatus (device) request, the firmware must respond and let the host know if the USB peripheral device is currently bus powered
//or self powered. See chapter 9 in the official USB specifications for details regarding this request. If the peripheral device is capable of being both
//self and bus powered, it should not return a hard coded value for this request. Instead, firmware should check if it is currently self or bus powered, and
//respond accordingly. If the hardware has been configured like demonstrated on the PICDEM FS USB Demo Board, an I/O pin can be polled to determine the
//currently selected power source. On the PICDEM FS USB Demo Board, "RA2" is used for this purpose. If using this feature, make sure "USE_SELF_POWER_SENSE_IO"
//has been defined in HardwareProfile.h, and that an appropriate I/O pin has been mapped to it in HardwareProfile.h.
// #if defined(USE_SELF_POWER_SENSE_IO)
// tris_self_power = INPUT_PIN; // See HardwareProfile.h
// #endif
//Enable the USB port now - we will check to see if Vbus is powered at the end of init and disable it if not.
//USBDeviceInit(); //usb_device.c. Initializes USB module SFRs and firmware variables to known states.
//------------------------
//----- SETUP TIMERS -----
//------------------------
//(INCLUDE THE USAGE OF ALL TIMERS HERE EVEN IF NOT SETUP HERE SO THIS IS THE ONE POINT OF
//REFERENCE TO KNOW WHICH TIMERS ARE IN USE AND FOR WHAT).
//----- SETUP TIMER 1 -----
//Used for: Available
//OpenTimer1((T1_ON | T1_IDLE_CON | T1_GATE_OFF | T1_PS_1_4 | T1_SOURCE_INT), 20000);
//----- SETUP TIMER 2 -----
//Used for:
//OpenTimer2((T2_ON | T2_IDLE_CON | T2_GATE_OFF | T2_PS_1_1 | T2_SOURCE_INT), 0xffff); //0xffff = 305Hz
//----- SETUP TIMER 3 -----
//Used for:
//OpenTimer3((T3_ON | T3_IDLE_CON | T3_GATE_OFF | T3_PS_1_1 | T3_SOURCE_INT), PIEZO_TIMER_PERIOD);
//----- SETUP TIMER 4 -----
//Used for:
//OpenTimer4((T4_ON | T4_IDLE_CON | T4_GATE_OFF | T4_PS_1_1 | T4_SOURCE_INT), 20000);
//----- SETUP TIMER 5 -----
//Used for: Heartbeat
OpenTimer5((T5_ON | T5_IDLE_CON | T5_GATE_OFF | T5_PS_1_1 | T5_SOURCE_INT), 40000); //1mS with 80MHz osc and PB_DIV_2
ConfigIntTimer5(T5_INT_ON | T5_INT_PRIOR_7); //1=lowest priority to 7=highest priority. ISR function must specify same value
//---------------------------------
//----- SETUP EVAL BOARD CPLD -----
//---------------------------------
//Graphics bus width = 16
mPORTGSetPinsDigitalOut(BIT_14);
mPORTGSetBits(BIT_14);
//SPI source select = SPI3 (not used)
mPORTGSetPinsDigitalOut(BIT_12);
mPORTGClearBits(BIT_12);
//SPI peripheral destination select = Expansion Slot (not used)
mPORTASetPinsDigitalOut(BIT_7 | BIT_6);
mPORTASetBits(BIT_7);
mPORTAClearBits(BIT_6);
//--------------------------------------
//----- PARALLEL MASTER PORT SETUP -----
//--------------------------------------
PMMODE = 0;
PMAEN = 0;
PMCON = 0;
PMMODE = 0x0610;
PMCONbits.PTRDEN = 1; //Enable RD line
PMCONbits.PTWREN = 1; //Enable WR line
PMCONbits.PMPEN = 1; //Enable PMP
//------------------------------
//----- INITIALISE DISPLAY -----
//------------------------------
display_initialise();
display_test();
//LOAD OUR GLOBAL HTML STYLES FILE READY FOR DISPLAY HTML PAGES
BYTE dummy_styles_count;
DWORD file_size;
if (display_html_setup_read_file(global_css, 0, &file_size))
{
dummy_styles_count = 0;
display_html_read_styles(&file_size, &dummy_styles_count, 1); //1 = this is global styles file
}
}
void Terminal(void)
{
const char str1[] = {'k',0x00,'e',0x00,'y',0x00,'.',0x00,'b',0x00,'m',0x00,'p',0x00,'\0',0x00};
const char str2[] = {'\\',0x00,'s',0x00,'y',0x00,'s',0x00,'\0',0x00};
char KeyBuffer[31]={'Q','W','E','R','T','Y','U','I','O','P','A','S','D','F','G','H','J','K','L','Z','X','C','V','B','N','M',',',' ',' ',' ','.'};
char SpecialKeyBuffer[31]={'1','2','3','4','5','6','7','8','9','0','!','@','#','$','%','&','*','?','/','Z','"',' ','(',')','-','+',';',' ',' ',' ',':'};
const unsigned short int LetterPosX[4]={93,62,32,1};
const unsigned short int SpecialCharPosY[6]={1,284,1,39,245,284};
const unsigned short int LetterPosY[31]={1,33,65,97,129,161,193,225,257,289,
17,49,81,113,145,177,209,241,273,
49,81,113,145,177,209,241,
81,113,145,177,209};
_Bool NumSp=0,UppLow=0,ReadCmd=0,ErrorSyntax=0,HighApp=0,LowApp=0,SyntaxError=0,ExitApp=0,InitRfApp=0,SendApp=0,StatusRfApp=0,ReadApp=0,SetTime=0,SetDate=0;
char c[2]={'A',0x00};
char TextBuffer[10],i=0,b=0,Parametri=0,StringBuffer[50],Nchar=0,Param3[10],Param2[10],Param1[10],Param4[10],Param5[10];
unsigned short int clu=0, dat=0,DelCount=0,a=0x0000;
TRFData rfData;
char Minuti[3]={0x30,0x30,0x00};///minuti
char Ore[3]={0x30,0x31,0x00};///Ore
SSD1289_writeResgiter( 0x0049, 0x000A );///fine della finestra a 10 px
LCD_CLS(AZZURRO);
sprintf(TextBuffer,"Loading..");
LCD_Text57(2,1,TextBuffer,1,BLACK,NONE);
Xcursor=238;
Ycursor=2;
wFSchdir ((unsigned short int *)&str2[0]);
DrawBmp(0,319,(unsigned short int * )&str1[0],0);
SSD1289_writeResgiter( 0x0049, 0x013F );
while(TRUE)
{
if(PORTDbits.RD14==0)
{
read();
clu=getX();
dat=getY();
clu=(unsigned short int)((((float)6.01/(float)233.01)*(float)clu)+(float)clu);
dat=(unsigned short int)((((float)10.01/(float)313.01)*(float)dat)+(float)dat);
b=0;
for(i=0; i<31; i++)
{
///lettere
if((LetterPosX[b]<=clu)&&(clu<=(LetterPosX[b]+29))&&((LetterPosY[i]<=dat)&&(dat<=(LetterPosY[i]+29))))//la Q
{
///se attivo caratteri speciali
if(NumSp) c[0]=SpecialKeyBuffer[i];
else c[0]=KeyBuffer[i];
if((UppLow==1)&&(NumSp==0))
{
switch(c[0])
{
case ',':
break;
case' ':
break;
case'.':
break;
default:
c[0]+=0x20;
break;
}
}
LCD_FastRect(Xcursor-6,Ycursor,Xcursor,Ycursor+5,WHITE);
strcpy(TextBuffer,c);
StringBuffer[Nchar]=c[0];
LCD_Text57Land(Xcursor,Ycursor,TextBuffer,1,BLACK,NONE);
Nchar++;
//Ycursor+=6;
if(Ycursor>=319)
{
Ycursor=2;
Xcursor-=8;
Nchar=0;
}
DelayMs(50);
}
if(i==9) b++;
if(i==18) b++;
if(i==25) b++;
}
///comandi speciali
b=2;
for(i=0; i<6; i++)
{
if((LetterPosX[b]<=clu)&&(clu<=(LetterPosX[b]+29))&&((SpecialCharPosY[i]<=dat)&&(dat<=(SpecialCharPosY[i]+34))))//la Q
{
switch(i)
{
case 0:
///da implementare Upper/lower letter
if(UppLow==0)
{
UppLow=1;
LCD_Cercle(53,29,3,1,GRAY);
}
else
{
UppLow=0;
LCD_Cercle(53,29,3,1,BLUE);
}
break;
case 1:
LCD_FastRect(Xcursor-6,Ycursor,Xcursor,Ycursor+5,AZZURRO);
Ycursor-=6;
Nchar--;
if(Ycursor>350)
{
Ycursor=314;
Xcursor+=8;
Nchar=0;
if(Xcursor>241) Xcursor=238;
}
break;
case 2:
///da implementare
break;
case 3:
///da implementare
break;
case 4:
///da implementare attiva/disattiva numeri+caratteri speciali
if(NumSp==0)
{
NumSp=1;
LCD_Cercle(22,274,3,1,BLUE);
}
else
{
NumSp=0;
LCD_Cercle(22,274,3,1,GRAY);
}
break;
case 5:
///torna a capo riga (invio)
LCD_FastRect(Xcursor-6,Ycursor,Xcursor,Ycursor+5,AZZURRO);
NumSp=0;
LCD_Cercle(22,274,3,1,GRAY);
UppLow=0;
LCD_Cercle(53,29,3,1,BLUE);
Ycursor=2;
Xcursor-=8;
if(Xcursor<=136)
{
LCD_FastRect(121,0,239,319,AZZURRO);
Xcursor=238;
}
ReadCmd=1;
StringBuffer[Nchar]=0x00;
Nchar=0;
break;
}
DelayMs(50);
}
if(i==1) b=3;
}
}
///Lampeggio cursore
DelayMs(1);
DelCount++;
if(DelCount==200)
{
DelCount=0;
if(a==0x00000) a=0xffff;
else a=0x0000;
LCD_FastRect(Xcursor-6,Ycursor,Xcursor,Ycursor+5,a);
}
///Se premuto invio..
if(ReadCmd==1)
{
ReadCmd=0;
ErrorSyntax=0;
Parametri=0;
b=0;
///Ciclo per verificare la stringa passata
///carica in Param1, Param2, Param3, ogni parola separata da uno spazio
for(i=0; i<20; i++)
{
if(StringBuffer[i]==0x20) {Parametri=1; Param1[i]=0x00; break;}
if(StringBuffer[i]==0x00) {Parametri=1; Param1[i]=0x00; break;}
Param1[i]=StringBuffer[i];
}
if(StringBuffer[i]!=0x00)
{
b=0;
for(i<20; i++;)
{
if(StringBuffer[i]==0x20) {Parametri=2; Param2[b]=0x00; break;}
if(StringBuffer[i]==0x00) {Parametri=2; Param2[b]=0x00; break;}
Param2[b]=StringBuffer[i];
b++;
}
}
if(StringBuffer[i]!=0x00)
{
b=0;
for(i<20; i++;)
{
if(StringBuffer[i]==0x20) {Parametri=3; Param3[b]=0x00; break;}
if(StringBuffer[i]==0x00) {Parametri=3; Param3[b]=0x00; break;}
Param3[b]=StringBuffer[i];
b++;
}
}
if(StringBuffer[i]!=0x00)
{
b=0;
for(i<20; i++;)
{
if(StringBuffer[i]==0x20) {Parametri=4; Param4[b]=0x00; break;}
if(StringBuffer[i]==0x00) {Parametri=4; Param4[b]=0x00; break;}
Param4[b]=StringBuffer[i];
b++;
}
}
if(StringBuffer[i]!=0x00)
{
b=0;
for(i<20; i++;)
{
if(StringBuffer[i]==0x20) {Parametri=5; Param5[b]=0x00; break;}
if(StringBuffer[i]==0x00) {Parametri=5; Param5[b]=0x00; break;}
Param5[b]=StringBuffer[i];
b++;
}
}
///Fine ciclo
//Verifica le stringhe
//da completare salta al programma...
if(strcmp(Param1,"HIGH")==FALSE) HighApp=1;
if(strcmp(Param1,"LOW")==FALSE) LowApp=1;
if(strcmp(Param1,"EXIT")==FALSE) ExitApp=1;
if(strcmp(Param1,"REBOOT")==FALSE) SoftReset();
if(strcmp(Param1,"SEND")==FALSE) SendApp=1;
if(strcmp(Param1,"INITRF")==FALSE) InitRfApp=1;
if(strcmp(Param1,"STATUSRF")==FALSE) StatusRfApp=1;
if(strcmp(Param1,"READRF")==FALSE) ReadApp=1;
if(strcmp(Param1,"SETTIME")==FALSE) SetTime=1;
if(strcmp(Param1,"SETDATE")==FALSE) SetDate=1;
if((HighApp==0)&&(LowApp==0)&&(ExitApp==0)&&(SendApp==0)&&(InitRfApp==0)&&(StatusRfApp==0)&&(ReadApp==0)&&(SetTime==0)&&(SetDate==0)) SyntaxError=1;
if(SetTime)
{
SetTime=0;
Ore[0]=Param2[0];
Ore[1]=Param2[1];
Minuti[0]=Param3[0];
Minuti[1]=Param3[1];
if((Ore[0]>=0x32)&&(Ore[1]>=0x34))
{
sprintf(StringBuffer,"Ore invalide!");
LCD_Text57Land(Xcursor,Ycursor,StringBuffer,1,RED,NONE);
}
else if(Minuti[0]>=0x36)
{
sprintf(StringBuffer,"Minuti invalidi!");
LCD_Text57Land(Xcursor,Ycursor,StringBuffer,1,RED,NONE);
}
else{
lastTime.hour=atobcd(&Ore[0]);
lastTime.min=atobcd(&Minuti[0]);
RtccSetTimeDate(lastTime.l, lastDate.l);
sprintf(StringBuffer,"Time updated!");
LCD_Text57Land(Xcursor,Ycursor,StringBuffer,1,BLACK,NONE);
}
}
if(StatusRfApp)
{
StatusRfApp=0;
StatusRead();
sprintf(StringBuffer,"%02x ",TransceiverStatus.bits.RG_FF_IT);
LCD_Text57Land(Xcursor,Ycursor,StringBuffer,1,BLACK,NONE);
Ycursor+=16;
sprintf(StringBuffer,"%02x ",TransceiverStatus.bits.POR);
LCD_Text57Land(Xcursor,Ycursor,StringBuffer,1,BLACK,NONE);
Ycursor+=16;
sprintf(StringBuffer,"%02x ",TransceiverStatus.bits.RGUR_FFOV);
LCD_Text57Land(Xcursor,Ycursor,StringBuffer,1,BLACK,NONE);
Ycursor+=16;
sprintf(StringBuffer,"%02x ",TransceiverStatus.bits.WKUP);
LCD_Text57Land(Xcursor,Ycursor,StringBuffer,1,BLACK,NONE);
Ycursor+=16;
sprintf(StringBuffer,"%02x ",TransceiverStatus.bits.EXT);
LCD_Text57Land(Xcursor,Ycursor,StringBuffer,1,BLACK,NONE);
Ycursor+=16;
sprintf(StringBuffer,"%02x ",TransceiverStatus.bits.LBD);
LCD_Text57Land(Xcursor,Ycursor,StringBuffer,1,BLACK,NONE);
Ycursor+=16;
sprintf(StringBuffer,"%02x ",TransceiverStatus.bits.FFEM);
LCD_Text57Land(Xcursor,Ycursor,StringBuffer,1,BLACK,NONE);
Ycursor+=16;
sprintf(StringBuffer,"%02x ",TransceiverStatus.bits.RSSI_ATS);
LCD_Text57Land(Xcursor,Ycursor,StringBuffer,1,BLACK,NONE);
Ycursor+=16;
sprintf(StringBuffer,"%02x ",TransceiverStatus.bits.DQD);
LCD_Text57Land(Xcursor,Ycursor,StringBuffer,1,BLACK,NONE);
Ycursor+=16;
sprintf(StringBuffer,"%02x ",TransceiverStatus.bits.CRL);
LCD_Text57Land(Xcursor,Ycursor,StringBuffer,1,BLACK,NONE);
Ycursor+=16;
sprintf(StringBuffer,"%02x ",TransceiverStatus.bits.ATGL);
LCD_Text57Land(Xcursor,Ycursor,StringBuffer,1,BLACK,NONE);
Ycursor=2;
}
if(InitRfApp)
{
InitRfApp=0;
if(strcmp(Param2,"OFF")==FALSE)
{
MRF49XA_Power_Down();
sprintf(StringBuffer,"RF Stopped!");
LCD_Text57Land(Xcursor,Ycursor,StringBuffer,1,RED,NONE);
}
else{
initRFPorts();
MRF49XA_Init();
InitRFData(&rfData);
sprintf(StringBuffer,"RF Initialized! %x",RF_IRQ);
LCD_Text57Land(Xcursor,Ycursor,StringBuffer,1,BLACK,NONE);
}
}
if(ReadApp)///Test sniff pacchetti
{
WORD GENCREG2 = (0x8000|XTAL_LD_CAP_125);
WORD CFSREG2 ;
WORD DRVSREG2 ;
WORD RXCREG2 ;
WORD PMCREG2 = 0x8201;
WORD TXCREG2 = 0x9850;
volatile BOOL RxPacketValid[BANK_SIZE];
BYTE RxPacket[BANK_SIZE][80];
volatile BYTE RxPacketLen[BANK_SIZE];
WORD totalReceived = 0;
unsigned char FreqBand=0,DataRate=0,Nop=0;
ReadApp=0;
sprintf(StringBuffer,"Reading..");
LCD_Text57Land(Xcursor,Ycursor,StringBuffer,1,BLACK,AZZURRO);
//Setta le porte
mPORTFSetPinsDigitalOut(BIT_5);//SDO
mPORTFSetPinsDigitalOut(BIT_13);//SCK
mPORTBSetPinsDigitalOut(BIT_14);//CS
mPORTBSetPinsDigitalOut(BIT_13);//FSEL
mPORTESetPinsDigitalIn(BIT_9);//FINT
mPORTESetPinsDigitalIn(BIT_8);//IRQ
mPORTFSetPinsDigitalIn(BIT_4);//SDI
mPORTFSetPinsDigitalIn(BIT_12);//INT
SPI4CON = 0x0120;
//SPI1BRG = 0x001F; // 64:1 prescale (slow display update)
SPI4BRG = 0x0001; // 4:1 prescale (fast display update) 16Mhz spi clock at 72Mhz sys clock
SPI4CONSET = 0x8000; // enables the spi
RF_RSCLR;
DelayUs(10);
RF_RSSET;
DelayMs(125);
RF_CSSET;
RF_FSELSET;
//RF_SCKCLR;
//RF_SDOCLR;
///Fine init porte
i=Param2[0];
//i=1;
switch(i)
{
case '1':
FreqBand = 1;
break;
case '2':
FreqBand = 2;
break;
case '3':
FreqBand = 3;
break;
}
GENCREG2 |= ((WORD)FreqBand << 4);
i=Param3[0];
//i=1;
switch(i)
{
case '1':
DataRate = 1;
DRVSREG2 = 0xC623;
break;
case '2':
DataRate = 2;
DRVSREG2 = 0xC611;
break;
case '3':
DataRate = 3;
DRVSREG2 = 0xC608;
break;
case '4':
DataRate = 4;
DRVSREG2 = 0xC605;
break;
case '5':
DataRate = 5;
DRVSREG2 = 0xC602;
break;
}
i=Param4[0];
//i=4;
switch(i)
{
case '1':
RXCREG2 = 0x9421;
break;
case '2':
RXCREG2 = 0x9441;
break;
case '3':
RXCREG2 = 0x9461;
break;
case '4':
RXCREG2 = 0x9481;
break;
case '5':
RXCREG2 = 0x94A1;
break;
case '6':
RXCREG2 = 0x94C1;
break;
}
switch(FreqBand)
{
case 1:
CFSREG2 = 0xA640;
break;
case 2:
CFSREG2 = 0xA640;
break;
case 3:
CFSREG2 = 0xA7D0;
break;
default:
break;
}
//Init RF
SPI_Command(FIFORSTREG);
SPI_Command( FIFORSTREG | 0x0002);
SPI_Command(GENCREG2);
SPI_Command(0xC4F7);
SPI_Command(CFSREG2);
SPI_Command(DRVSREG2);
SPI_Command(PMCREG2);
SPI_Command(RXCREG2);
SPI_Command(TXCREG2);
SPI_Command(PMCREG2 | 0x0020);
DelayMs(5);
SPI_Command(PMCREG2 | 0x0080);
SPI_Command(GENCREG2 | 0x0040);
SPI_Command(FIFORSTREG);
SPI_Command( FIFORSTREG | 0x0002);
SPI_Command(0x0000);
//InitRFData(&rfData);
sprintf(StringBuffer,"%x, %x, %x",Param2[0],Param3[0],Param4[0]);
LCD_Text57Land(Xcursor,Ycursor,StringBuffer,1,BLACK,AZZURRO);
sprintf(StringBuffer,"%x,%x",RF_IRQ,RF_INT);
LCD_Text57Land(Xcursor,Ycursor,StringBuffer,1,BLACK,AZZURRO);
while(TRUE)
{
if((RF_IRQ==0)||(RF_INT==1))
{
//nCS = 0;
RF_CSCLR;
Nop++;
if( SPI_SDI == 1 )
{
BYTE RxPacketPtr;
BYTE tmpPacketLen;
BYTE bIndex;
WORD counter;
// There is data in RX FIFO
//nCS = 1;
//nFSEL = 0; // FIFO selected
RF_CSSET;
RF_FSELCLR;
tmpPacketLen = SPI_Read();
for(bIndex = 0; bIndex < BANK_SIZE; bIndex++)
{
if( RxPacketValid[bIndex] == FALSE )
{
break;
}
}
if( tmpPacketLen >= 80 || tmpPacketLen == 0 || bIndex >= BANK_SIZE )
{
IGNORE_HERE:
//nFSEL = 1; // bad packet len received
RF_FSELSET;
SPI_Command(PMCREG2); // turn off the transmitter and receiver
SPI_Command(FIFORSTREG); // reset FIFO
SPI_Command(GENCREG2); // disable FIFO, TX_latch
SPI_Command(GENCREG2 | 0x0040); // enable FIFO
SPI_Command(PMCREG2 | 0x0080); // turn on receiver
SPI_Command(FIFORSTREG | 0x0002); // FIFO synchron latch re-enabled
goto RETURN_HERE;
}
RxPacketLen[bIndex] = tmpPacketLen;
//RLED = 1;
//nFSEL = 1;
mPORTDSetBits(BIT_2);
RF_FSELSET;
RxPacketPtr = 0;
counter = 0;
while(1)
{
if( counter++ == 0xFFFF )
{
goto IGNORE_HERE;
}
else if( RF_FINT == 1)
{
//nFSEL = 0;
RF_FSELCLR;
counter = 0;
RxPacket[bIndex][RxPacketPtr++] = SPI_Read();
if( RxPacketPtr >= RxPacketLen[bIndex] )
{
BYTE i;
//nFSEL = 1;
//nCS = 0;
RF_FSELSET;
RF_CSCLR;
//SPI_SDO = 0;
RF_SDOCLR;
Nop++;
for(i = 0; i < 8; i++)
{
//SPI_SCK = 1;
//SPI_SCK = 0;
RF_SCKSET;
Nop++;
RF_SCKCLR;
Nop++;
}
if( SPI_SDI == 0 )
{
goto IGNORE_HERE;
}
//nCS = 1;
RF_CSSET;
SPI_Command(FIFORSTREG);
//RLED = 0;
mPORTDClearBits(BIT_2);
RxPacketValid[bIndex] = TRUE;
SPI_Command(FIFORSTREG | 0x0002); // FIFO synchron latch re-enable
goto RETURN_HERE;
}
//nFSEL = 1;
RF_FSELSET;
}
}
}
else // read the rest of the interrupts
{
SPI_Read();
//nCS = 1;
RF_CSSET;
}
RETURN_HERE:
Nop++;
}
for(i = 0; i < BANK_SIZE; i++)
{
if( RxPacketValid[i] == TRUE )
{
BYTE j;
WORD received_crc;
WORD calculated_crc;
totalReceived++;
//Printf("\r\n");
Xcursor-=8;
Ycursor=2;
sprintf(StringBuffer,"%04x | %04x |",totalReceived,RxPacketLen[i]);
LCD_Text57Land(Xcursor,Ycursor,StringBuffer,1,BLACK,NONE);
//PrintChar(totalReceived>>8);
//PrintChar(totalReceived);
//Printf(" | ");
//PrintChar(RxPacketLen[i]);
//Printf(" | ");
for(j = 0; j < RxPacketLen[i]; j++)
{
sprintf(StringBuffer,"%02x ",RxPacket[i][j]);
LCD_Text57Land(Xcursor,Ycursor,StringBuffer,1,BLACK,NONE);
Ycursor+=12;
//PrintChar(RxPacket[i][j]);
//Printf(" ");
}
received_crc = ((WORD)RxPacket[i][RxPacketLen[i]-1]) + (((WORD)RxPacket[i][RxPacketLen[i]-2]) << 8);
calculated_crc = CRC16(RxPacket[i], RxPacketLen[i]-2);
if( received_crc != calculated_crc )
{
//Printf(" * CRC");
sprintf(StringBuffer," * CRC");
LCD_Text57Land(Xcursor,Ycursor,StringBuffer,1,BLACK,NONE);
}
RxPacketValid[i] = FALSE;
}
}
//i=MRF49XA_Receive_Packet(&rfData);
//DelayUs(50);
//if(i==3) break;
//if(i==2) break;
//if(i==1) break;
//sprintf(StringBuffer,"%x,%x,%x",RF_IRQ,RF_FINT,SPI_SDI);
//LCD_Text57Land(Xcursor,Ycursor,StringBuffer,1,BLACK,AZZURRO);
if(PORTDbits.RD14==0) break;
}
Xcursor-=8;
sprintf(StringBuffer,"Ricevuto! %d, 0x%02x, 0x%02x, 0x%02x, 0x%02x",i,rfData.buffer[0],rfData.buffer[1],rfData.buffer[2],rfData.buffer[3]);
LCD_Text57Land(Xcursor,Ycursor,StringBuffer,1,BLACK,NONE);
}
if(SendApp)
{
SendApp=0;
//LCD_FastRect(121,0,239,319,AZZURRO);
AddRFData(&rfData,Param2[0]);
MRF49XA_Send_Packet(&rfData);
InitRFData(&rfData);
sprintf(StringBuffer,"Dato inviato..");
LCD_Text57Land(Xcursor,Ycursor,StringBuffer,1,BLACK,NONE);
}
if(HighApp)
{
HighApp=0;
if(strcmp(Param2,"D2")==FALSE)
{
sprintf(StringBuffer,"D2 Actived! 1");
LCD_Text57Land(Xcursor,Ycursor,StringBuffer,1,GREEN,NONE);
mPORTDSetPinsDigitalOut(BIT_2);
mPORTDSetBits(BIT_2);
}
else
{
sprintf(StringBuffer,"Port Not Found!");
LCD_Text57Land(Xcursor,Ycursor,StringBuffer,1,RED,NONE);
}
}
if(LowApp)
{
LowApp=0;
if(strcmp(Param2,"D2")==FALSE)
{
sprintf(StringBuffer,"D2 Deactived! 0");
LCD_Text57Land(Xcursor,Ycursor,StringBuffer,1,GREEN,NONE);
mPORTDSetPinsDigitalOut(BIT_2);
mPORTDClearBits(BIT_2);
}
else
{
sprintf(StringBuffer,"Port Not Found!");
LCD_Text57Land(Xcursor,Ycursor,StringBuffer,1,RED,NONE);
}
}
if(SyntaxError)
{
SyntaxError=0;
sprintf(StringBuffer,"Syntax Error!");
LCD_Text57Land(Xcursor,Ycursor,StringBuffer,1,RED,NONE);
}
if(ExitApp==1) break;
Xcursor-=8;
Ycursor=2;
for(i=0; i<10; i++)
{
StringBuffer[i]=0x00;
Param1[i]=0x00;
Param2[i]=0x00;
Param3[i]=0x00;
}
}
if(PORTDbits.RD3==0) break;
}
}
