Ejemplos de nrf_adv_conn_init en C++ (Cpp)

Ejemplo n.º 1

Archivo: main.c Proyecto: Eppo791906066/nRF51-ble-bcast-mesh

/**
* @brief RBC_MESH framework event handler. Defined in rbc_mesh.h. Handles
*   events coming from the mesh. Sets LEDs according to data
*
* @param[in] evt RBC event propagated from framework
*/
void rbc_mesh_event_handler(rbc_mesh_event_t* evt)
{
    TICK_PIN(28);
    switch (evt->event_type)
    {
        case RBC_MESH_EVENT_TYPE_CONFLICTING_VAL:   
        case RBC_MESH_EVENT_TYPE_NEW_VAL:
        case RBC_MESH_EVENT_TYPE_UPDATE_VAL:
        
            if (evt->value_handle > 2)
                break;
            
            led_config(evt->value_handle, evt->data[0]);
            break;
        case RBC_MESH_EVENT_TYPE_INITIALIZED:
            /* init BLE gateway softdevice application: */
            nrf_adv_conn_init();
            break;  
    }
}

Ejemplo n.º 2

Archivo: main.c Proyecto: tkadom/TWBLE

/** @brief main function */
int main(void)
{
    uart_init();

    PUTS("LED Mesh initializing");

    /* Enable Softdevice (including sd_ble before framework */
    uint32_t error_code = 
        sd_softdevice_enable(NRF_CLOCK_LFCLKSRC_XTAL_75_PPM, sd_assert_handler);
    APP_ERROR_CHECK(error_code);
    
    ble_enable_params_t ble_enable_params;
    memset(&ble_enable_params, 0, sizeof(ble_enable_params));

    ble_enable_params.gatts_enable_params.service_changed = 0;
    ble_enable_params.gatts_enable_params.attr_tab_size = BLE_GATTS_ATTR_TAB_SIZE_DEFAULT;

    error_code = sd_ble_enable(&ble_enable_params);
    APP_ERROR_CHECK(error_code);

    /* init leds and pins */
    gpio_init();

#ifdef RBC_MESH_SERIAL

    /* only want to enable serial interface, and let external host setup the framework */
    mesh_aci_init();

#else
    /* Enable mesh framework on channel 37, min adv interval at 100ms, 
        2 characteristics */
    rbc_mesh_init_params_t init_params;

    init_params.access_addr = 0xA541A68F;
    init_params.adv_int_ms = 100;
    init_params.channel = 38;
    init_params.handle_count = 2;
    init_params.packet_format = RBC_MESH_PACKET_FORMAT_ORIGINAL;
    init_params.radio_mode = RBC_MESH_RADIO_MODE_BLE_1MBIT;

    error_code = rbc_mesh_init(init_params);
    APP_ERROR_CHECK(error_code);

    /* request values for both LEDs on the mesh */
    error_code = rbc_mesh_value_enable(1);
    APP_ERROR_CHECK(error_code);
    error_code = rbc_mesh_value_enable(2);
    APP_ERROR_CHECK(error_code);


    /* init BLE gateway softdevice application: */
    nrf_adv_conn_init();

#endif

    /* enable softdevice IRQ */
    error_code = sd_nvic_EnableIRQ(SD_EVT_IRQn);


#ifndef BUTTONS
    /* sleep */
    while (true)
    {
        sd_app_evt_wait();
    }


#else
    uint8_t mesh_data[16] = {0,0};
    while (true)
    {
        // red off
        if(nrf_gpio_pin_read(BUTTON_1) == 0)
        {
            PUTS("BUTTON_1 pressed");
            while(nrf_gpio_pin_read(BUTTON_1) == 0);
            mesh_data[0] = 0;
            rbc_mesh_value_set(1, mesh_data, 1);
        }
        // red on
        if(nrf_gpio_pin_read(BUTTON_2) == 0)
        {
            PUTS("BUTTON_1 pressed");
            while(nrf_gpio_pin_read(BUTTON_2) == 0);
            mesh_data[0] = 1;
            rbc_mesh_value_set(1, mesh_data, 1);
        }
        // green off 
        if(nrf_gpio_pin_read(BUTTON_3) == 0)
        {
            PUTS("BUTTON_3 pressed");
            while(nrf_gpio_pin_read(BUTTON_3) == 0);
            mesh_data[0] = 0;
            rbc_mesh_value_set(2, mesh_data, 1);
        }
        // green on
         if(nrf_gpio_pin_read(BUTTON_4) == 0)
        {
            PUTS("BUTTON_4 pressed");
            while(nrf_gpio_pin_read(BUTTON_4) == 0);
            mesh_data[0] = 1;
            rbc_mesh_value_set(2, mesh_data, 1);
        }
    }
#endif

}