/**
* Test nvm_eeprom_load_byte_to_buffer(), nvm_eeprom_flush_buffer() and
* nvm_eeprom_atomic_write_page()
*
* Test procedure:
* - Erase the TEST_ATOMIC_WRITE_PAGE page.
* - Load byte and then flush the buffer at one location.
* - Load two more bytes at a different location.
* - Write the page.
* - Verify that only two bytes are written and the rest of the page is erased.
*
* \return STATUS_OK if test succeeded, otherwise ERR_BAD_DATA
*/
static status_code_t test_atomic_write(void)
{
nvm_eeprom_erase_page(TEST_ATOMIC_WRITE_PAGE);
/* Load a dummy byte and then flush the buffer to remove the byte from
* the buffer. The byte should not be written to the EEPROM.
*/
nvm_eeprom_load_byte_to_buffer(0, 55);
nvm_eeprom_flush_buffer();
/* Load some additional bytes */
set_buffer(buffer, EEPROM_ERASED);
buffer[1] = 0xaa;
buffer[2] = 0x19;
nvm_eeprom_load_byte_to_buffer(1, buffer[1]);
nvm_eeprom_load_byte_to_buffer(2, buffer[2]);
/* Erase and then write page */
nvm_eeprom_atomic_write_page(TEST_ATOMIC_WRITE_PAGE);
if (is_eeprom_page_equal_to_buffer(TEST_ATOMIC_WRITE_PAGE, buffer)) {
return STATUS_OK;
}
return ERR_BAD_DATA;
}
/**
* \brief Fill temporary EEPROM page buffer with value.
*
* This fills the the EEPROM page buffers with a given value.
* If memory mapped EEPROM is enabled, this function will not work.
*
* \note Only the lower part of the address is used to address the buffer.
* Therefore, no address parameter is needed. In the end, the data
* is written to the EEPROM page given by the address parameter to the
* EEPROM write page operation.
*
* \param value Value to copy to the page buffer.
*/
void nvm_eeprom_fill_buffer_with_value(uint8_t value)
{
uint8_t old_cmd;
old_cmd = NVM.CMD;
nvm_eeprom_flush_buffer();
// Wait until NVM is ready
nvm_wait_until_ready();
NVM.CMD = NVM_CMD_LOAD_EEPROM_BUFFER_gc;
/* Set address to zero, as only the lower bits matters. ADDR0 is
* maintained inside the loop below.
*/
NVM.ADDR2 = 0x00;
NVM.ADDR1 = 0x00;
// Load multible bytes into page buffer
uint8_t i;
for (i = 0; i < EEPROM_PAGE_SIZE; ++i) {
NVM.ADDR0 = i;
NVM.DATA0 = value;
}
NVM.CMD = old_cmd;
}
/**
* \brief Write one byte to EEPROM using IO mapping.
*
* This function writes one byte to EEPROM using IO-mapped access.
* This function will cancel all ongoing EEPROM page buffer loading
* operations, if any.
*
* \param address EEPROM address (max EEPROM_SIZE)
* \param value Byte value to write to EEPROM.
*/
void nvm_eeprom_write_byte(eeprom_addr_t address, uint8_t value)
{
uint8_t old_cmd;
Assert(address <= EEPROM_SIZE);
/* Flush buffer to make sure no unintentional data is written and load
* the "Page Load" command into the command register.
*/
old_cmd = NVM.CMD;
nvm_eeprom_flush_buffer();
// Wait until NVM is ready
nvm_wait_until_ready();
nvm_eeprom_load_byte_to_buffer(address, value);
// Set address to write to
NVM.ADDR2 = 0x00;
NVM.ADDR1 = (address >> 8) & 0xFF;
NVM.ADDR0 = address & 0xFF;
/* Issue EEPROM Atomic Write (Erase&Write) command. Load command, write
* the protection signature and execute command.
*/
NVM.CMD = NVM_CMD_ERASE_WRITE_EEPROM_PAGE_gc;
nvm_exec();
NVM.CMD = old_cmd;
}
/**
* \brief Test EEPROM atomic write
*
* This test erases test page \ref TEST_ATOMIC_WRITE_PAGE, then writes the first
* byte in the page buffer before flushing it -- this byte should then not be
* written to the EEPROM -- and writing different values to the two successive
* bytes. An atomic write is then executed before the write of the latter two
* bytes is verified.
*
* \param test Current test case.
*/
static void run_eeprom_atomic_write_test(const struct test_case *test)
{
uint8_t buffer[EEPROM_PAGE_SIZE];
bool success;
nvm_eeprom_erase_page(TEST_ATOMIC_WRITE_PAGE);
/* Load a dummy byte and then flush the buffer to remove the byte from
* the buffer. The byte should not be written to the EEPROM.
*/
nvm_eeprom_load_byte_to_buffer(0, 55);
nvm_eeprom_flush_buffer();
/* Load some additional bytes */
set_buffer(buffer, EEPROM_ERASED);
buffer[1] = 0xaa;
buffer[2] = 0x19;
nvm_eeprom_load_byte_to_buffer(1, buffer[1]);
nvm_eeprom_load_byte_to_buffer(2, buffer[2]);
/* Erase and then write page */
nvm_eeprom_atomic_write_page(TEST_ATOMIC_WRITE_PAGE);
success = is_eeprom_page_equal_to_buffer(TEST_ATOMIC_WRITE_PAGE, buffer);
test_assert_true(test, success,
"Page buffer flush, byte load or atomic write failed");
}
/**
* \brief Fill temporary EEPROM page buffer with value.
*
* This fills the the EEPROM page buffers with a given value.
* If memory mapped EEPROM is enabled, this function will not work.
*
* \note Only the lower part of the address is used to address the buffer.
* Therefore, no address parameter is needed. In the end, the data
* is written to the EEPROM page given by the address parameter to the
* EEPROM write page operation.
*
* \param value Value to copy to the page buffer.
*/
void nvm_eeprom_fill_buffer_with_value(uint8_t value)
{
nvm_eeprom_flush_buffer();
// Wait until NVM is ready
nvm_wait_until_ready();
// Load multiple bytes into page buffer
uint8_t i;
for (i = 0; i < EEPROM_PAGE_SIZE; ++i) {
nvm_eeprom_load_byte_to_buffer(i, value);
}
}
