//--------------------------------------------------------------------------
// Send 1 bit of communication to the 1-Wire Net and verify that the
// response matches the 'applyPowerResponse' bit and apply power delivery
// to the 1-Wire net. Note that some implementations may apply the power
// first and then turn it off if the response is incorrect.
//
// 'portnum' - number 0 to MAX_PORTNUM-1. This number was provided to
// OpenCOM to indicate the port number.
// 'applyPowerResponse' - 1 bit response to check, if correct then start
// power delivery
//
// Returns: TRUE: bit written and response correct, strong pullup now on
// FALSE: response incorrect
//
SMALLINT owReadBitPower(int portnum, SMALLINT applyPowerResponse)
{
if (!owHasPowerDelivery(portnum))
return FALSE;
if(owTouchBit(portnum,0x01) != applyPowerResponse)
return FALSE;
if(owLevel(portnum,MODE_STRONG5) != MODE_STRONG5)
return FALSE;
return TRUE;
}
//--------------------------------------------------------------------------
// Send 8 bits of communication to the 1-Wire Net and verify that the
// 8 bits read from the 1-Wire Net is the same (write operation).
// The parameter 'sendbyte' least significant 8 bits are used. After the
// 8 bits are sent change the level of the 1-Wire net.
//
// 'portnum' - number 0 to MAX_PORTNUM-1. This number was provided to
// OpenCOM to indicate the port number.
// 'sendbyte' - 8 bits to send (least significant byte)
//
// Returns: TRUE: bytes written and echo was the same
// FALSE: echo was not the same
//
SMALLINT owWriteBytePower(int portnum, SMALLINT sendbyte)
{
if (!owHasPowerDelivery(portnum))
return FALSE;
if(owTouchByte(portnum,sendbyte) != sendbyte)
return FALSE;
if(owLevel(portnum,MODE_STRONG5) != MODE_STRONG5)
return FALSE;
return TRUE;
}
//--------------------------------------------------------------------------
// Read 8 bits of communication to the 1-Wire Net and then turn on
// power delivery.
//
// 'portnum' - number 0 to MAX_PORTNUM-1. This number was provided to
// OpenCOM to indicate the port number.
//
// Returns: byte read
// FALSE: power delivery failed
//
SMALLINT owReadBytePower(int portnum)
{
SMALLINT getbyte;
if (!owHasPowerDelivery(portnum))
return FALSE;
getbyte = owTouchByte(portnum,0xFF);
if (owLevel(portnum,MODE_STRONG5) != MODE_STRONG5)
return FALSE;
return getbyte;
}
//----------------------------------------------------------------------
// Family 0x10 Demo
//
void main(void)
{
int temp;
int sign;
BYTE i;
//----------------------------------------
ADCON1 = 0x07; // PortB digital
bTRD6 = 1; // RD6 = Serial Input
bTRD7 = 0; // RD7 = Serial Output
bLD7 = 1;
printf("\nFamily 0x10 Demo\n%");
////////////////////////////////////////////////////////////
// Initialise the OneWire network (bus)
// attempt to acquire the 1-Wire Nets
if (!owAcquire(0, NULL)) {
printf("Acquire failed.\n%");
while(1)
;
}
////////////////////////////////////////////////////////////
// Let's set the alarmtemps of all devices on the bus.
// To demonstrate this, we write a low alarmtemp of 19
// and a high alarmtemp of 21 to all devices.
// Finally we copy the alarmtemps to non-volatile EEPROM.
printf("\nStart - Set AlarmTemperatures.\n%");
// Reset the devices
owTouchReset(0);
// Address all devices on the net
owWriteByte(0, OW_SKIPROM);
// Use the WriteScratchpad command to set AlarmTemps
owWriteByte(0, OW_WRITESCRATCHPAD);
owWriteByte(0, 19); // Valid RoomTemperature
owWriteByte(0, 21); // 19 <= Temp < 21
printf("End - Set AlarmTemperatures.\n%");
// Set alarmtemps done
// Copy the temps to EEPROM
printf("\nStart - Write AlarmTemperatures to EEPROM.\n%");
// Reset the devices
owTouchReset(0);
// Address all devices on the net
owWriteByte(0, OW_SKIPROM);
// send the CopyScratchpad command to copy the AlarmTemps to EEPROM
// If the bus supports Strong PullUp, we use it (because
// there might be parasite powered devices on this bus).
if(owHasPowerDelivery(0)) {
printf("The bus has a Strong PullUp\n%");
owWriteBytePower(0, OW_COPYSCRATCHPAD);
// Eeprom update takes 10 milliseconds max. 11ms is safer
Wait(11);
// turn off the strong pull-up
owLevel(0, MODE_NORMAL);
} else {
printf("The bus has NO Strong PullUp\n%");
owWriteByte(0, OW_COPYSCRATCHPAD);
// Eeprom update takes 10 milliseconds max. 11ms is safer
Wait(11);
}
printf("End - Write AlarmTemperatures to EEPROM.\n%");
// Copy the temps to EEPROM done
while(1) {
////////////////////////////////////////////////////////////
// We do a temp conversion on all DS18S20's
printf("\nStart - TemperatureConversions\n%");
// Reset the devices
owTouchReset(0);
// Address all devices on this net
owWriteByte(0, OW_SKIPROM);
// Send the convert command and start power delivery if available.
// Note that we use a different way here to determine
// Strong PullUp capability.
if(owWriteBytePower(0, OW_CONVERTT)) {
printf("We are using a Strong PullUp.\n%");
} else {
printf("No Strong PullUp configured.\n%");
owWriteByte(0, OW_CONVERTT);
}
// Coversion takes 750 milliseconds max. 751ms is safer
Wait(751);
// turn off the 1-Wire Net strong pull-up
owLevel(0, MODE_NORMAL);
printf("End - TemperatureConversions\n%");
////////////////////////////////////////////////////////////
// We will now demonstrate an alarmsearch
printf("\nStart - Find devices in alarmstate\n%");
// Find the devices with temp < 19 or temp >= 21
if(!owFirst(0, TRUE, TRUE)) {
printf("No devices in AlarmState found.\n%");
} else {
do {
printf("Device in AlarmState found: 0x%02X%02X%02X%02X%02X%02X%02X%02X\n%",
owNetCurrent.SerialNum[7],
owNetCurrent.SerialNum[6],
owNetCurrent.SerialNum[5],
owNetCurrent.SerialNum[4],
owNetCurrent.SerialNum[3],
owNetCurrent.SerialNum[2],
owNetCurrent.SerialNum[1],
owNetCurrent.SerialNum[0]);
} while(owNext(0, TRUE, TRUE));
}
printf("End - Find devices in alarmstate\n%");
////////////////////////////////////////////////////////////
// We will now demonstrate a normal search. For
// every device found, it's temperature is retrieved.
printf("\nStart - Find devices and get their temperatures.\n%");
if(!owFirst(0, TRUE, FALSE)) {
printf("No devices found.\n%");
} else {
do {
printf("Device found: 0x%02X%02X%02X%02X%02X%02X%02X%02X%",
owNetCurrent.SerialNum[7],
owNetCurrent.SerialNum[6],
owNetCurrent.SerialNum[5],
owNetCurrent.SerialNum[4],
owNetCurrent.SerialNum[3],
owNetCurrent.SerialNum[2],
owNetCurrent.SerialNum[1],
owNetCurrent.SerialNum[0]);
// Init the crc
setcrc8(0, 0);
// Read the device's memory
owWriteByte(0, OW_READSCRATCHPAD);
for(i = 0; i < SCRATCHPAD_SIZE; i++) {
ScratchPad[i] = owReadByte(0);
docrc8(0, ScratchPad[i]);
}
// Check the CRC
if(owNetCurrent.utilcrc8 != 0) {
printf(", crc is NOT OK.\n%");
} else {
// We don't want to use float's
temp = ((int)ScratchPad[SCRATCHPAD_TEMPERATUREMSB] << 8) |
(int)ScratchPad[SCRATCHPAD_TEMPERATURELSB];
if(temp < 0) {
temp = -temp;
sign = '-';
} else if(temp == 0) {
sign = ' ';
} else {
sign = '+';
}
printf(", Temperature is %c%d.%d degrees\n%",
sign,
(temp >> 1),
(temp & 0x01) ? 5 : 0);
}
} while(owNext(0, TRUE, FALSE));
}
printf("End - Find devices and get their temperatures.\n%");
////////////////////////////////////////////////////////////
Wait(1); // Just a convenient way to set a breakpoint
}
}
