/**
* @brief Main function of the Terminal Target application
* @ingroup App_API
*/
int main(void)
{
/* Initialize all layers */
if (nwk_init() != NWK_SUCCESS)
{
/* something went wrong during initialization */
pal_alert();
}
/* disable pull-ups */
MCUCR |= (1u << PUD);
#ifdef FLASH_NVRAM
pal_ps_set(EE_IEEE_ADDR,IEEE_ADDRESS_BYTES, &tal_pib_IeeeAddress);
#endif
/* Initialize LEDs. */
pal_led_init();
pal_led(LED_START, LED_ON); /* indicating application is started */
pal_led(LED_NWK_SETUP, LED_OFF); /* indicating network is started */
pal_led(LED_DATA, LED_OFF); /* indicating data reception */
/*
* The stack is initialized above, hence the global interrupts are enabled
* here.
*/
pal_global_irq_enable();
/**
* @brief TWI and QT600 interface initialization
*/
int i;
twi_master_init();
RESET_QT600_PIN_INIT();
RESET_QT600_ON();
for (i = 0; i < 100 ; i++)
asm("nop");
/* Endless while loop */
while (1)
{
app_task(); /* Application task */
if(rf4ce_new_msg == 1)
{
twi_send_message();
TX_index = 0;
rf4ce_new_msg = 0;
}
nwk_task(); /* RF4CE network layer task */
}
}
/**
* @brief Main function of the Wireless UART application
*/
int main(void)
{
/* Initialize the TAL layer */
if (tal_init() != MAC_SUCCESS)
{
// something went wrong during initialization
pal_alert();
}
/* Calibrate MCU's RC oscillator */
pal_calibrate_rc_osc();
/* Initialize LEDs */
pal_led_init();
pal_led(LED_START, LED_ON); // indicating application is started
pal_led(LED_DATA_RX, LED_OFF); // indicating data reception
pal_led(LED_DATA_TX, LED_OFF); // indicating successfull data transmission
/*
* The stack is initialized above, hence the global interrupts are enabled
* here.
*/
pal_global_irq_enable();
/* Initialize the serial interface used for communication with terminal program */
if (pal_sio_init(SIO_CHANNEL) != MAC_SUCCESS)
{
// something went wrong during initialization
pal_alert();
}
/* Configure TX frame and transceiver */
configure_frame_sending();
/* Switch receiver on */
tal_rx_enable(PHY_RX_ON);
#if(SEND_BLOCKWISE==true)
start_timer();
#endif
/* Endless while loop */
while (1)
{
pal_task(); /* Handle platform specific tasks, like serial interface */
tal_task(); /* Handle transceiver specific tasks */
#if(!(SEND_BLOCKWISE==true))
app_task(); /* Application task */
#endif
}
}
/**
* @brief Main function of the Sniffer application
*/
int main(void)
{
/* Initialize the TAL layer */
if (tal_init() != MAC_SUCCESS)
{
/* something went wrong during initialization*/
pal_alert();
}
/* Calibrate MCU's RC oscillator */
pal_calibrate_rc_osc();
/* Initialize LEDs */
pal_led_init();
/*
* The stack is initialized above, hence the global interrupts are enabled
* here.
*/
pal_global_irq_enable();
/* Initialize the serial interface used for communication with sniffer
GUI */
if (pal_sio_init(SIO_CHANNEL) != MAC_SUCCESS)
{
/* something went wrong during initialization */
pal_alert();
}
//sio_getchar();
Wireshark_Settings = INIT_STATE ;
/* Endless while loop */
while (1)
{
pal_task();
tal_task();
app_task();
}
}