void omap_perseus2_init_irq(void)
{
omap1_init_common_hw();
omap_init_irq();
omap_gpio_init();
perseus2_init_smc91x();
}
static void __init omap_perseus2_init(void)
{
omap_writew(omap_readw(OMAP7XX_DSP_M_CTL) & ~1, OMAP7XX_DSP_M_CTL);
omap_writel(0x0000fff3, OMAP7XX_FLASH_CFG_0);
omap_writel(0x00000088, OMAP7XX_FLASH_ACFG_0);
omap_writel(0x0000fff3, OMAP7XX_FLASH_CFG_1);
omap_writel(0x00000000, OMAP7XX_FLASH_ACFG_1);
omap_writel(omap_readl(OMAP7XX_IO_CONF_9) & 0x1FFFFFFF,
OMAP7XX_IO_CONF_9);
perseus2_init_smc91x();
if (gpio_request(P2_NAND_RB_GPIO_PIN, "NAND ready") < 0)
BUG();
gpio_direction_input(P2_NAND_RB_GPIO_PIN);
omap_cfg_reg(L3_1610_FLASH_CS2B_OE);
omap_cfg_reg(M8_1610_FLASH_CS2B_WE);
omap_cfg_reg(E2_7XX_KBR0);
omap_cfg_reg(J7_7XX_KBR1);
omap_cfg_reg(E1_7XX_KBR2);
omap_cfg_reg(F3_7XX_KBR3);
omap_cfg_reg(D2_7XX_KBR4);
omap_cfg_reg(C2_7XX_KBC0);
omap_cfg_reg(D3_7XX_KBC1);
omap_cfg_reg(E4_7XX_KBC2);
omap_cfg_reg(F4_7XX_KBC3);
omap_cfg_reg(E3_7XX_KBC4);
platform_add_devices(devices, ARRAY_SIZE(devices));
omap_serial_init();
omap_register_i2c_bus(1, 100, NULL, 0);
omapfb_set_lcd_config(&perseus2_lcd_config);
}
void omap_perseus2_init_irq(void)
{
omap_init_irq();
omap_gpio_init();
perseus2_init_smc91x();
}
static void __init omap_perseus2_init(void)
{
/* Early, board-dependent init */
/*
* Hold GSM Reset until needed
*/
omap_writew(omap_readw(OMAP7XX_DSP_M_CTL) & ~1, OMAP7XX_DSP_M_CTL);
/*
* UARTs -> done automagically by 8250 driver
*/
/*
* CSx timings, GPIO Mux ... setup
*/
/* Flash: CS0 timings setup */
omap_writel(0x0000fff3, OMAP7XX_FLASH_CFG_0);
omap_writel(0x00000088, OMAP7XX_FLASH_ACFG_0);
/*
* Ethernet support through the debug board
* CS1 timings setup
*/
omap_writel(0x0000fff3, OMAP7XX_FLASH_CFG_1);
omap_writel(0x00000000, OMAP7XX_FLASH_ACFG_1);
/*
* Configure MPU_EXT_NIRQ IO in IO_CONF9 register,
* It is used as the Ethernet controller interrupt
*/
omap_writel(omap_readl(OMAP7XX_IO_CONF_9) & 0x1FFFFFFF,
OMAP7XX_IO_CONF_9);
perseus2_init_smc91x();
if (gpio_request(P2_NAND_RB_GPIO_PIN, "NAND ready") < 0)
BUG();
gpio_direction_input(P2_NAND_RB_GPIO_PIN);
omap_cfg_reg(L3_1610_FLASH_CS2B_OE);
omap_cfg_reg(M8_1610_FLASH_CS2B_WE);
/* Mux pins for keypad */
omap_cfg_reg(E2_7XX_KBR0);
omap_cfg_reg(J7_7XX_KBR1);
omap_cfg_reg(E1_7XX_KBR2);
omap_cfg_reg(F3_7XX_KBR3);
omap_cfg_reg(D2_7XX_KBR4);
omap_cfg_reg(C2_7XX_KBC0);
omap_cfg_reg(D3_7XX_KBC1);
omap_cfg_reg(E4_7XX_KBC2);
omap_cfg_reg(F4_7XX_KBC3);
omap_cfg_reg(E3_7XX_KBC4);
platform_add_devices(devices, ARRAY_SIZE(devices));
omap_board_config = perseus2_config;
omap_board_config_size = ARRAY_SIZE(perseus2_config);
omap_serial_init();
omap_register_i2c_bus(1, 100, NULL, 0);
}
