Ejemplos de pmic_fg_program_design_cap en C++ (Cpp)

Ejemplo n.º 1

Archivo: dc_xpwr_battery.c Proyecto: yutokt/android_kernel_intel_anzhen4

static void pmic_fg_init_config_regs(struct pmic_fg_info *info)
{
	int ret;


	/*
	 * check if the config data is already
	 * programmed and if so just return.
	 */
	ret = pmic_fg_reg_readb(info, DC_FG_CNTL_REG);
	if (ret < 0) {
		dev_warn(&info->pdev->dev, "FG CNTL reg read err!!\n");
	} else if ((ret & FG_CNTL_OCV_ADJ_EN) && (ret & FG_CNTL_CAP_ADJ_EN)) {
		dev_info(&info->pdev->dev,
			"FG data except the OCV curve is initialized\n");
		/*
		 * ocv curve will be set to default values
		 * at every boot, so it is needed to explicitly write
		 * the ocv curve data for each boot
		 */
		ret = pmic_fg_program_ocv_curve(info);
		if (ret < 0)
			dev_err(&info->pdev->dev,
				"set ocv curve fail:%d\n", ret);
		/* comment the following for FW may have touched the regsiters */
		/*info->fg_init_done = true;*/
		/*pmic_fg_dump_init_regs(info);*/
		/*return;*/
	} else {
		dev_info(&info->pdev->dev, "FG data need to be initialized\n");
	}


	ret = pmic_fg_program_ocv_curve(info);
	if (ret < 0)
		dev_err(&info->pdev->dev, "set ocv curve fail:%d\n", ret);

	ret = pmic_fg_program_rdc_vals(info);
	if (ret < 0)
		dev_err(&info->pdev->dev, "set rdc fail:%d\n", ret);

	ret = pmic_fg_program_design_cap(info);
	if (ret < 0)
		dev_err(&info->pdev->dev, "set design cap fail:%d\n", ret);

	ret = pmic_fg_program_vbatt_full(info);
	if (ret < 0)
		dev_err(&info->pdev->dev, "set vbatt full fail:%d\n", ret);

	ret = pmic_fg_set_lowbatt_thresholds(info);
	if (ret < 0)
		dev_err(&info->pdev->dev, "lowbatt thr set fail:%d\n", ret);

	ret = pmic_fg_reg_writeb(info, DC_FG_CNTL_REG, 0xff);
	if (ret < 0)
		dev_err(&info->pdev->dev, "gauge cntl set fail:%d\n", ret);

	info->fg_init_done = true;
	pmic_fg_dump_init_regs(info);
}

Ejemplo n.º 2

Archivo: dc_xpwr_battery.c Proyecto: NotKit/android-ia_kernel_intel_baytrail

static void pmic_fg_init_config_regs(struct pmic_fg_info *info)
{
	int ret;


	/*
	 * check if the config data is already
	 * programmed and if so just return.
	 */
	ret = pmic_fg_reg_readb(info, DC_FG_CNTL_REG);
	if (ret < 0) {
		dev_warn(&info->pdev->dev, "FG CNTL reg read err!!\n");
	} else if ((ret & FG_CNTL_OCV_ADJ_EN) && (ret & FG_CNTL_CAP_ADJ_EN)) {
		dev_dbg(&info->pdev->dev, "FG data is already initialized\n");
		/* comment the following for FW may have touched the regsiters */
		/* info->fg_init_done = true; */
		/* pmic_fg_dump_init_regs(info); */
		/* return; */
	} else {
		dev_dbg(&info->pdev->dev, "FG data need to be initialized\n");
	}


	ret = pmic_fg_program_ocv_curve(info);
	if (ret < 0)
		dev_err(&info->pdev->dev, "set ocv curve fail:%d\n", ret);

	ret = pmic_fg_program_rdc_vals(info);
	if (ret < 0)
		dev_err(&info->pdev->dev, "set rdc fail:%d\n", ret);

	ret = pmic_fg_program_design_cap(info);
	if (ret < 0)
		dev_err(&info->pdev->dev, "set design cap fail:%d\n", ret);

	ret = pmic_fg_program_vbatt_full(info);
	if (ret < 0)
		dev_err(&info->pdev->dev, "set vbatt full fail:%d\n", ret);

	ret = pmic_fg_set_lowbatt_thresholds(info);
	if (ret < 0)
		dev_err(&info->pdev->dev, "lowbatt thr set fail:%d\n", ret);

	ret = pmic_fg_reg_writeb(info, DC_FG_CNTL_REG, 0xf7);
	if (ret < 0)
		dev_err(&info->pdev->dev, "gauge cntl set fail:%d\n", ret);

	info->fg_init_done = true;
	/* no need to dump registers except in debug cases
	pmic_fg_dump_init_regs(info); */
}