void qoriq_start_thread(void)
{
const Per_CPU_Control *cpu_self = _Per_CPU_Get();
ppc_exc_initialize_interrupt_stack(
(uintptr_t) cpu_self->interrupt_stack_low,
rtems_configuration_get_interrupt_stack_size()
);
bsp_interrupt_facility_initialize();
_SMP_Start_multitasking_on_secondary_processor();
}
void ppc_exc_initialize_with_vector_base(
uintptr_t interrupt_stack_begin,
uintptr_t interrupt_stack_size,
void *vector_base
)
{
rtems_status_code sc = RTEMS_SUCCESSFUL;
const ppc_exc_categories *const categories = ppc_exc_current_categories();
unsigned vector = 0;
uint32_t sda_base = 0;
uint32_t r13 = 0;
if (categories == NULL) {
ppc_exc_fatal_error();
}
/* Assembly code needs SDA_BASE in r13 (SVR4 or EABI). Make sure
* early init code put it there.
*/
__asm__ volatile (
"lis %0, _SDA_BASE_@h\n"
"ori %0, %0, _SDA_BASE_@l\n"
"mr %1, 13\n"
: "=r" (sda_base), "=r"(r13)
);
if (sda_base != r13) {
ppc_exc_fatal_error();
}
ppc_exc_initialize_interrupt_stack(interrupt_stack_begin, interrupt_stack_size);
#ifndef PPC_EXC_CONFIG_BOOKE_ONLY
/* Use current MMU / RI settings when running C exception handlers */
ppc_exc_msr_bits = ppc_machine_state_register() & (MSR_DR | MSR_IR | MSR_RI);
#ifdef __ALTIVEC__
/* Need vector unit enabled to save/restore altivec context */
ppc_exc_msr_bits |= MSR_VE;
#endif
#endif /* PPC_EXC_CONFIG_BOOKE_ONLY */
if (ppc_cpu_is_bookE() == PPC_BOOKE_STD || ppc_cpu_is_bookE() == PPC_BOOKE_E500) {
ppc_exc_initialize_booke(vector_base);
}
for (vector = 0; vector <= LAST_VALID_EXC; ++vector) {
ppc_exc_category category = ppc_exc_category_for_vector(categories, vector);
if (category != PPC_EXC_INVALID) {
void *const vector_address = ppc_exc_vector_address(vector, vector_base);
uint32_t prologue [16];
size_t prologue_size = sizeof(prologue);
sc = ppc_exc_make_prologue(
vector,
vector_base,
category,
prologue,
&prologue_size
);
if (sc != RTEMS_SUCCESSFUL) {
ppc_exc_fatal_error();
}
ppc_code_copy(vector_address, prologue, prologue_size);
}
}
#ifndef PPC_EXC_CONFIG_BOOKE_ONLY
/* If we are on a classic PPC with MSR_DR enabled then
* assert that the mapping for at least this task's
* stack is write-back-caching enabled (see README/CAVEATS)
* Do this only if the cache is physically enabled.
* Since it is not easy to figure that out in a
* generic way we need help from the BSP: BSPs
* which run entirely w/o the cache may set
* ppc_exc_cache_wb_check to zero prior to calling
* this routine.
*
* We run this check only after exception handling is
* initialized so that we have some chance to get
* information printed if it fails.
*
* Note that it is unsafe to ignore this issue; if
* the check fails, do NOT disable it unless caches
* are always physically disabled.
*/
if (ppc_exc_cache_wb_check && (MSR_DR & ppc_exc_msr_bits)) {
/* The size of 63 assumes cache lines are at most 32 bytes */
uint8_t dummy[63];
uintptr_t p = (uintptr_t) dummy;
/* If the dcbz instruction raises an alignment exception
* then the stack is mapped as write-thru or caching-disabled.
* The low-level code is not capable of dealing with this
* ATM.
*/
p = (p + 31U) & ~31U;
__asm__ volatile ("dcbz 0, %0"::"b" (p));
/* If we make it thru here then things seem to be OK */
}
