/*
* board init
*/
static void __init eva_init(void)
{
r8a7740_clock_init(MD_CK0 | MD_CK2);
eva_clock_init();
pinctrl_register_mappings(eva_pinctrl_map, ARRAY_SIZE(eva_pinctrl_map));
r8a7740_pinmux_init();
r8a7740_meram_workaround();
/*
* Touchscreen
* TODO: Move reset GPIO over to .dts when we can reference it
*/
gpio_request_one(166, GPIOF_OUT_INIT_HIGH, NULL); /* TP_RST_B */
#ifdef CONFIG_CACHE_L2X0
/* Early BRESP enable, Shared attribute override enable, 32K*8way */
l2x0_init(IOMEM(0xf0002000), 0x40440000, 0x82000fff);
#endif
r8a7740_add_standard_devices_dt();
r8a7740_pm_init();
}
static void __init eva_init(void)
{
struct platform_device *usb = NULL;
regulator_register_always_on(0, "fixed-3.3V", fixed3v3_power_consumers,
ARRAY_SIZE(fixed3v3_power_consumers), 3300000);
regulator_register_always_on(3, "fixed-5.0V", fixed5v0_power_consumers,
ARRAY_SIZE(fixed5v0_power_consumers), 5000000);
pinctrl_register_mappings(eva_pinctrl_map, ARRAY_SIZE(eva_pinctrl_map));
pwm_add_table(pwm_lookup, ARRAY_SIZE(pwm_lookup));
r8a7740_pinmux_init();
r8a7740_meram_workaround();
/* LCDC0 */
gpio_request_one(61, GPIOF_OUT_INIT_HIGH, NULL); /* LCDDON */
/* GETHER */
gpio_request_one(18, GPIOF_OUT_INIT_HIGH, NULL); /* PHY_RST */
/* USB */
gpio_request_one(159, GPIOF_IN, NULL); /* USB_DEVICE_MODE */
if (gpio_get_value(159)) {
/* USB Host */
} else {
/* USB Func */
/*
* The USBHS interrupt handlers needs to read the IRQ pin value
* (HI/LOW) to diffentiate USB connection and disconnection
* events (usbhsf_get_vbus()). We thus need to select both the
* intc_irq7_1 pin group and GPIO 209 here.
*/
gpio_request_one(209, GPIOF_IN, NULL);
platform_device_register(&usbhsf_device);
usb = &usbhsf_device;
}
/* CON1/CON15 Camera */
gpio_request_one(173, GPIOF_OUT_INIT_LOW, NULL); /* STANDBY */
gpio_request_one(172, GPIOF_OUT_INIT_HIGH, NULL); /* RST */
/* see mt9t111_power() */
gpio_request_one(158, GPIOF_OUT_INIT_LOW, NULL); /* CAM_PON */
/* FSI-WM8978 */
gpio_request(7, NULL);
gpio_request(8, NULL);
gpio_direction_none(GPIO_PORT7CR); /* FSIAOBT needs no direction */
gpio_direction_none(GPIO_PORT8CR); /* FSIAOLR needs no direction */
/*
* CAUTION
*
* DBGMD/LCDC0/FSIA MUX
* DBGMD_SELECT_B should be set after setting PFC Function.
*/
gpio_request_one(176, GPIOF_OUT_INIT_HIGH, NULL);
/*
* We can switch CON8/CON14 by SW1.5,
* but it needs after DBGMD_SELECT_B
*/
gpio_request_one(6, GPIOF_IN, NULL);
if (gpio_get_value(6)) {
/* CON14 enable */
} else {
/* CON8 (SDHI1) enable */
pinctrl_register_mappings(eva_sdhi1_pinctrl_map,
ARRAY_SIZE(eva_sdhi1_pinctrl_map));
platform_device_register(&vcc_sdhi1);
platform_device_register(&sdhi1_device);
}
#ifdef CONFIG_CACHE_L2X0
/* Early BRESP enable, Shared attribute override enable, 32K*8way */
l2x0_init(IOMEM(0xf0002000), 0x40440000, 0x82000fff);
#endif
i2c_register_board_info(0, i2c0_devices, ARRAY_SIZE(i2c0_devices));
i2c_register_board_info(2, i2c2_devices, ARRAY_SIZE(i2c2_devices));
r8a7740_add_standard_devices();
platform_add_devices(eva_devices,
ARRAY_SIZE(eva_devices));
rmobile_add_device_to_domain("A4LC", &lcdc0_device);
rmobile_add_device_to_domain("A4LC", &hdmi_lcdc_device);
if (usb)
rmobile_add_device_to_domain("A3SP", usb);
r8a7740_pm_init();
}
static void __init eva_init(void)
{
struct platform_device *usb = NULL;
regulator_register_always_on(0, "fixed-3.3V", fixed3v3_power_consumers,
ARRAY_SIZE(fixed3v3_power_consumers), 3300000);
r8a7740_pinmux_init();
r8a7740_meram_workaround();
/* SCIFA1 */
gpio_request(GPIO_FN_SCIFA1_RXD, NULL);
gpio_request(GPIO_FN_SCIFA1_TXD, NULL);
/* LCDC0 */
gpio_request(GPIO_FN_LCDC0_SELECT, NULL);
gpio_request(GPIO_FN_LCD0_D0, NULL);
gpio_request(GPIO_FN_LCD0_D1, NULL);
gpio_request(GPIO_FN_LCD0_D2, NULL);
gpio_request(GPIO_FN_LCD0_D3, NULL);
gpio_request(GPIO_FN_LCD0_D4, NULL);
gpio_request(GPIO_FN_LCD0_D5, NULL);
gpio_request(GPIO_FN_LCD0_D6, NULL);
gpio_request(GPIO_FN_LCD0_D7, NULL);
gpio_request(GPIO_FN_LCD0_D8, NULL);
gpio_request(GPIO_FN_LCD0_D9, NULL);
gpio_request(GPIO_FN_LCD0_D10, NULL);
gpio_request(GPIO_FN_LCD0_D11, NULL);
gpio_request(GPIO_FN_LCD0_D12, NULL);
gpio_request(GPIO_FN_LCD0_D13, NULL);
gpio_request(GPIO_FN_LCD0_D14, NULL);
gpio_request(GPIO_FN_LCD0_D15, NULL);
gpio_request(GPIO_FN_LCD0_D16, NULL);
gpio_request(GPIO_FN_LCD0_D17, NULL);
gpio_request(GPIO_FN_LCD0_D18_PORT40, NULL);
gpio_request(GPIO_FN_LCD0_D19_PORT4, NULL);
gpio_request(GPIO_FN_LCD0_D20_PORT3, NULL);
gpio_request(GPIO_FN_LCD0_D21_PORT2, NULL);
gpio_request(GPIO_FN_LCD0_D22_PORT0, NULL);
gpio_request(GPIO_FN_LCD0_D23_PORT1, NULL);
gpio_request(GPIO_FN_LCD0_DCK, NULL);
gpio_request(GPIO_FN_LCD0_VSYN, NULL);
gpio_request(GPIO_FN_LCD0_HSYN, NULL);
gpio_request(GPIO_FN_LCD0_DISP, NULL);
gpio_request(GPIO_FN_LCD0_LCLK_PORT165, NULL);
gpio_request_one(GPIO_PORT61, GPIOF_OUT_INIT_HIGH, NULL); /* LCDDON */
gpio_request_one(GPIO_PORT202, GPIOF_OUT_INIT_LOW, NULL); /* LCD0_LED_CONT */
/* Touchscreen */
gpio_request(GPIO_FN_IRQ10, NULL); /* TP_INT */
gpio_request_one(GPIO_PORT166, GPIOF_OUT_INIT_HIGH, NULL); /* TP_RST_B */
/* GETHER */
gpio_request(GPIO_FN_ET_CRS, NULL);
gpio_request(GPIO_FN_ET_MDC, NULL);
gpio_request(GPIO_FN_ET_MDIO, NULL);
gpio_request(GPIO_FN_ET_TX_ER, NULL);
gpio_request(GPIO_FN_ET_RX_ER, NULL);
gpio_request(GPIO_FN_ET_ERXD0, NULL);
gpio_request(GPIO_FN_ET_ERXD1, NULL);
gpio_request(GPIO_FN_ET_ERXD2, NULL);
gpio_request(GPIO_FN_ET_ERXD3, NULL);
gpio_request(GPIO_FN_ET_TX_CLK, NULL);
gpio_request(GPIO_FN_ET_TX_EN, NULL);
gpio_request(GPIO_FN_ET_ETXD0, NULL);
gpio_request(GPIO_FN_ET_ETXD1, NULL);
gpio_request(GPIO_FN_ET_ETXD2, NULL);
gpio_request(GPIO_FN_ET_ETXD3, NULL);
gpio_request(GPIO_FN_ET_PHY_INT, NULL);
gpio_request(GPIO_FN_ET_COL, NULL);
gpio_request(GPIO_FN_ET_RX_DV, NULL);
gpio_request(GPIO_FN_ET_RX_CLK, NULL);
gpio_request_one(GPIO_PORT18, GPIOF_OUT_INIT_HIGH, NULL); /* PHY_RST */
/* USB */
gpio_request_one(GPIO_PORT159, GPIOF_IN, NULL); /* USB_DEVICE_MODE */
if (gpio_get_value(GPIO_PORT159)) {
/* USB Host */
} else {
/* USB Func */
/*
* A1 chip has 2 IRQ7 pin and it was controled by MSEL register.
* OTOH, usbhs interrupt needs its value (HI/LOW) to decide
* USB connection/disconnection (usbhsf_get_vbus()).
* This means we needs to select GPIO_FN_IRQ7_PORT209 first,
* and select GPIO_PORT209 here
*/
gpio_request(GPIO_FN_IRQ7_PORT209, NULL);
gpio_request_one(GPIO_PORT209, GPIOF_IN, NULL);
platform_device_register(&usbhsf_device);
usb = &usbhsf_device;
}
/* SDHI0 */
gpio_request(GPIO_FN_SDHI0_CMD, NULL);
gpio_request(GPIO_FN_SDHI0_CLK, NULL);
gpio_request(GPIO_FN_SDHI0_D0, NULL);
gpio_request(GPIO_FN_SDHI0_D1, NULL);
gpio_request(GPIO_FN_SDHI0_D2, NULL);
gpio_request(GPIO_FN_SDHI0_D3, NULL);
gpio_request(GPIO_FN_SDHI0_WP, NULL);
/*
* MMCIF
*
* Here doesn't care SW1.4 status,
* since CON2 is not mounted.
*/
gpio_request(GPIO_FN_MMC1_CLK_PORT103, NULL);
gpio_request(GPIO_FN_MMC1_CMD_PORT104, NULL);
gpio_request(GPIO_FN_MMC1_D0_PORT149, NULL);
gpio_request(GPIO_FN_MMC1_D1_PORT148, NULL);
gpio_request(GPIO_FN_MMC1_D2_PORT147, NULL);
gpio_request(GPIO_FN_MMC1_D3_PORT146, NULL);
gpio_request(GPIO_FN_MMC1_D4_PORT145, NULL);
gpio_request(GPIO_FN_MMC1_D5_PORT144, NULL);
gpio_request(GPIO_FN_MMC1_D6_PORT143, NULL);
gpio_request(GPIO_FN_MMC1_D7_PORT142, NULL);
/* CEU0 */
gpio_request(GPIO_FN_VIO0_D7, NULL);
gpio_request(GPIO_FN_VIO0_D6, NULL);
gpio_request(GPIO_FN_VIO0_D5, NULL);
gpio_request(GPIO_FN_VIO0_D4, NULL);
gpio_request(GPIO_FN_VIO0_D3, NULL);
gpio_request(GPIO_FN_VIO0_D2, NULL);
gpio_request(GPIO_FN_VIO0_D1, NULL);
gpio_request(GPIO_FN_VIO0_D0, NULL);
gpio_request(GPIO_FN_VIO0_CLK, NULL);
gpio_request(GPIO_FN_VIO0_HD, NULL);
gpio_request(GPIO_FN_VIO0_VD, NULL);
gpio_request(GPIO_FN_VIO0_FIELD, NULL);
gpio_request(GPIO_FN_VIO_CKO, NULL);
/* CON1/CON15 Camera */
gpio_request_one(GPIO_PORT173, GPIOF_OUT_INIT_LOW, NULL); /* STANDBY */
gpio_request_one(GPIO_PORT172, GPIOF_OUT_INIT_HIGH, NULL); /* RST */
/* see mt9t111_power() */
gpio_request_one(GPIO_PORT158, GPIOF_OUT_INIT_LOW, NULL); /* CAM_PON */
/* FSI-WM8978 */
gpio_request(GPIO_FN_FSIAIBT, NULL);
gpio_request(GPIO_FN_FSIAILR, NULL);
gpio_request(GPIO_FN_FSIAOMC, NULL);
gpio_request(GPIO_FN_FSIAOSLD, NULL);
gpio_request(GPIO_FN_FSIAISLD_PORT5, NULL);
gpio_request(GPIO_PORT7, NULL);
gpio_request(GPIO_PORT8, NULL);
gpio_direction_none(GPIO_PORT7CR); /* FSIAOBT needs no direction */
gpio_direction_none(GPIO_PORT8CR); /* FSIAOLR needs no direction */
/* FSI-HDMI */
gpio_request(GPIO_FN_FSIBCK, NULL);
/* HDMI */
gpio_request(GPIO_FN_HDMI_HPD, NULL);
gpio_request(GPIO_FN_HDMI_CEC, NULL);
/*
* CAUTION
*
* DBGMD/LCDC0/FSIA MUX
* DBGMD_SELECT_B should be set after setting PFC Function.
*/
gpio_request_one(GPIO_PORT176, GPIOF_OUT_INIT_HIGH, NULL);
/*
* We can switch CON8/CON14 by SW1.5,
* but it needs after DBGMD_SELECT_B
*/
gpio_request_one(GPIO_PORT6, GPIOF_IN, NULL);
if (gpio_get_value(GPIO_PORT6)) {
/* CON14 enable */
} else {
/* CON8 (SDHI1) enable */
gpio_request(GPIO_FN_SDHI1_CLK, NULL);
gpio_request(GPIO_FN_SDHI1_CMD, NULL);
gpio_request(GPIO_FN_SDHI1_D0, NULL);
gpio_request(GPIO_FN_SDHI1_D1, NULL);
gpio_request(GPIO_FN_SDHI1_D2, NULL);
gpio_request(GPIO_FN_SDHI1_D3, NULL);
gpio_request(GPIO_FN_SDHI1_CD, NULL);
gpio_request(GPIO_FN_SDHI1_WP, NULL);
/* SDSLOT2_PON */
gpio_request_one(GPIO_PORT16, GPIOF_OUT_INIT_HIGH, NULL);
platform_device_register(&sdhi1_device);
}
#ifdef CONFIG_CACHE_L2X0
/* Early BRESP enable, Shared attribute override enable, 32K*8way */
l2x0_init(IOMEM(0xf0002000), 0x40440000, 0x82000fff);
#endif
i2c_register_board_info(0, i2c0_devices, ARRAY_SIZE(i2c0_devices));
i2c_register_board_info(2, i2c2_devices, ARRAY_SIZE(i2c2_devices));
r8a7740_add_standard_devices();
platform_add_devices(eva_devices,
ARRAY_SIZE(eva_devices));
rmobile_add_device_to_domain("A4LC", &lcdc0_device);
rmobile_add_device_to_domain("A4LC", &hdmi_lcdc_device);
if (usb)
rmobile_add_device_to_domain("A3SP", usb);
r8a7740_pm_init();
}