Ejemplo n.º 1
0
/**
 * @brief   Low level serial driver configuration and (re)start.
 *
 * @param[in] sdp       pointer to a @p SerialDriver object
 * @param[in] config    the architecture-dependent serial driver configuration.
 *                      If this parameter is set to @p NULL then a default
 *                      configuration is used.
 *
 * @notapi
 */
void sd_lld_start(SerialDriver *sdp, const SerialConfig *config) {

  if (config == NULL)
    config = &default_config;

  if (sdp->state == SD_STOP) {
#if STM32_SERIAL_USE_USART1
    if (&SD1 == sdp) {
      rccEnableUSART1(FALSE);
      nvicEnableVector(STM32_USART1_NUMBER, STM32_SERIAL_USART1_PRIORITY);
    }
#endif
#if STM32_SERIAL_USE_USART2
    if (&SD2 == sdp) {
      rccEnableUSART2(FALSE);
      nvicEnableVector(STM32_USART2_NUMBER, STM32_SERIAL_USART2_PRIORITY);
    }
#endif
#if STM32_SERIAL_USE_USART3
    if (&SD3 == sdp) {
      rccEnableUSART3(FALSE);
      nvicEnableVector(STM32_USART3_NUMBER, STM32_SERIAL_USART3_PRIORITY);
    }
#endif
#if STM32_SERIAL_USE_UART4
    if (&SD4 == sdp) {
      rccEnableUART4(FALSE);
      nvicEnableVector(STM32_UART4_NUMBER, STM32_SERIAL_UART4_PRIORITY);
    }
#endif
#if STM32_SERIAL_USE_UART5
    if (&SD5 == sdp) {
      rccEnableUART5(FALSE);
      nvicEnableVector(STM32_UART5_NUMBER, STM32_SERIAL_UART5_PRIORITY);
    }
#endif
#if STM32_SERIAL_USE_USART6
    if (&SD6 == sdp) {
      rccEnableUSART6(FALSE);
      nvicEnableVector(STM32_USART6_NUMBER, STM32_SERIAL_USART6_PRIORITY);
    }
#endif
#if STM32_SERIAL_USE_UART7
    if (&SD7 == sdp) {
      rccEnableUART7(FALSE);
      nvicEnableVector(STM32_UART7_NUMBER, STM32_SERIAL_UART7_PRIORITY);
    }
#endif
#if STM32_SERIAL_USE_UART8
    if (&SD8 == sdp) {
      rccEnableUART8(FALSE);
      nvicEnableVector(STM32_UART8_NUMBER, STM32_SERIAL_UART8_PRIORITY);
    }
#endif
  }
  usart_init(sdp, config);
}
Ejemplo n.º 2
0
/**
 * @brief   Low level serial driver configuration and (re)start.
 *
 * @param[in] sdp       pointer to a @p SerialDriver object
 * @param[in] config    the architecture-dependent serial driver configuration.
 *                      If this parameter is set to @p NULL then a default
 *                      configuration is used.
 *
 * @notapi
 */
void sd_lld_start(SerialDriver *sdp, const SerialConfig *config) {

  if (config == NULL)
    config = &default_config;

  if (sdp->state == SD_STOP) {
#if STM32_SERIAL_USE_USART1
    if (&SD1 == sdp) {
      rccEnableUSART1(FALSE);
    }
#endif
#if STM32_SERIAL_USE_USART2
    if (&SD2 == sdp) {
      rccEnableUSART2(FALSE);
    }
#endif
#if STM32_SERIAL_USE_USART3
    if (&SD3 == sdp) {
      rccEnableUSART3(FALSE);
    }
#endif
#if STM32_SERIAL_USE_UART4
    if (&SD4 == sdp) {
      rccEnableUART4(FALSE);
    }
#endif
#if STM32_SERIAL_USE_UART5
    if (&SD5 == sdp) {
      rccEnableUART5(FALSE);
    }
#endif
#if STM32_SERIAL_USE_USART6
    if (&SD6 == sdp) {
      rccEnableUSART6(FALSE);
    }
#endif
#if STM32_SERIAL_USE_UART7
    if (&SD7 == sdp) {
      rccEnableUART7(FALSE);
    }
#endif
#if STM32_SERIAL_USE_UART8
    if (&SD8 == sdp) {
      rccEnableUART8(FALSE);
    }
#endif
#if STM32_SERIAL_USE_LPUART1
    if (&LPSD1 == sdp) {
      rccEnableLPUART1(FALSE);
    }
#endif
  }
  usart_init(sdp, config);
}
Ejemplo n.º 3
0
/**
 * @brief   Configures and activates the UART peripheral.
 *
 * @param[in] uartp     pointer to the @p UARTDriver object
 *
 * @notapi
 */
void uart_lld_start(UARTDriver *uartp) {

  if (uartp->state == UART_STOP) {
#if STM32_UART_USE_USART1
    if (&UARTD1 == uartp) {
      bool b;
      b = dmaStreamAllocate(uartp->dmarx,
                            STM32_UART_USART1_IRQ_PRIORITY,
                            (stm32_dmaisr_t)uart_lld_serve_rx_end_irq,
                            (void *)uartp);
      osalDbgAssert(!b, "stream already allocated");
      b = dmaStreamAllocate(uartp->dmatx,
                            STM32_UART_USART1_IRQ_PRIORITY,
                            (stm32_dmaisr_t)uart_lld_serve_tx_end_irq,
                            (void *)uartp);
      osalDbgAssert(!b, "stream already allocated");
      rccEnableUSART1(FALSE);
      nvicEnableVector(STM32_USART1_NUMBER, STM32_UART_USART1_IRQ_PRIORITY);
      uartp->dmamode |= STM32_DMA_CR_CHSEL(USART1_RX_DMA_CHANNEL) |
                        STM32_DMA_CR_PL(STM32_UART_USART1_DMA_PRIORITY);
    }
#endif

#if STM32_UART_USE_USART2
    if (&UARTD2 == uartp) {
      bool b;
      b = dmaStreamAllocate(uartp->dmarx,
                            STM32_UART_USART2_IRQ_PRIORITY,
                            (stm32_dmaisr_t)uart_lld_serve_rx_end_irq,
                            (void *)uartp);
      osalDbgAssert(!b, "stream already allocated");
      b = dmaStreamAllocate(uartp->dmatx,
                            STM32_UART_USART2_IRQ_PRIORITY,
                            (stm32_dmaisr_t)uart_lld_serve_tx_end_irq,
                            (void *)uartp);
      osalDbgAssert(!b, "stream already allocated");
      rccEnableUSART2(FALSE);
      nvicEnableVector(STM32_USART2_NUMBER, STM32_UART_USART2_IRQ_PRIORITY);
      uartp->dmamode |= STM32_DMA_CR_CHSEL(USART2_RX_DMA_CHANNEL) |
                        STM32_DMA_CR_PL(STM32_UART_USART2_DMA_PRIORITY);
    }
#endif

#if STM32_UART_USE_USART3
    if (&UARTD3 == uartp) {
      bool b;
      b = dmaStreamAllocate(uartp->dmarx,
                            STM32_UART_USART3_IRQ_PRIORITY,
                            (stm32_dmaisr_t)uart_lld_serve_rx_end_irq,
                            (void *)uartp);
      osalDbgAssert(!b, "stream already allocated");
      b = dmaStreamAllocate(uartp->dmatx,
                            STM32_UART_USART3_IRQ_PRIORITY,
                            (stm32_dmaisr_t)uart_lld_serve_tx_end_irq,
                            (void *)uartp);
      osalDbgAssert(!b, "stream already allocated");
      rccEnableUSART3(FALSE);
      nvicEnableVector(STM32_USART3_NUMBER, STM32_UART_USART3_IRQ_PRIORITY);
      uartp->dmamode |= STM32_DMA_CR_CHSEL(USART3_RX_DMA_CHANNEL) |
                        STM32_DMA_CR_PL(STM32_UART_USART3_DMA_PRIORITY);
    }
#endif

#if STM32_UART_USE_UART4
    if (&UARTD4 == uartp) {
      bool b;
      b = dmaStreamAllocate(uartp->dmarx,
                            STM32_UART_UART4_IRQ_PRIORITY,
                            (stm32_dmaisr_t)uart_lld_serve_rx_end_irq,
                            (void *)uartp);
      osalDbgAssert(!b, "stream already allocated");
      b = dmaStreamAllocate(uartp->dmatx,
                            STM32_UART_UART4_IRQ_PRIORITY,
                            (stm32_dmaisr_t)uart_lld_serve_tx_end_irq,
                            (void *)uartp);
      osalDbgAssert(!b, "stream already allocated");
      rccEnableUART4(FALSE);
      nvicEnableVector(STM32_UART4_NUMBER, STM32_UART_UART4_IRQ_PRIORITY);
      uartp->dmamode |= STM32_DMA_CR_CHSEL(UART4_RX_DMA_CHANNEL) |
                        STM32_DMA_CR_PL(STM32_UART_UART4_DMA_PRIORITY);
    }
#endif

#if STM32_UART_USE_UART5
    if (&UARTD5 == uartp) {
      bool b;
      b = dmaStreamAllocate(uartp->dmarx,
                            STM32_UART_UART5_IRQ_PRIORITY,
                            (stm32_dmaisr_t)uart_lld_serve_rx_end_irq,
                            (void *)uartp);
      osalDbgAssert(!b, "stream already allocated");
      b = dmaStreamAllocate(uartp->dmatx,
                            STM32_UART_UART5_IRQ_PRIORITY,
                            (stm32_dmaisr_t)uart_lld_serve_tx_end_irq,
                            (void *)uartp);
      osalDbgAssert(!b, "stream already allocated");
      rccEnableUART5(FALSE);
      nvicEnableVector(STM32_UART5_NUMBER, STM32_UART_UART5_IRQ_PRIORITY);
      uartp->dmamode |= STM32_DMA_CR_CHSEL(UART5_RX_DMA_CHANNEL) |
                        STM32_DMA_CR_PL(STM32_UART_UART5_DMA_PRIORITY);
    }
#endif

#if STM32_UART_USE_USART6
    if (&UARTD6 == uartp) {
      bool b;
      b = dmaStreamAllocate(uartp->dmarx,
                            STM32_UART_USART6_IRQ_PRIORITY,
                            (stm32_dmaisr_t)uart_lld_serve_rx_end_irq,
                            (void *)uartp);
      osalDbgAssert(!b, "stream already allocated");
      b = dmaStreamAllocate(uartp->dmatx,
                            STM32_UART_USART6_IRQ_PRIORITY,
                            (stm32_dmaisr_t)uart_lld_serve_tx_end_irq,
                            (void *)uartp);
      osalDbgAssert(!b, "stream already allocated");
      rccEnableUSART6(FALSE);
      nvicEnableVector(STM32_USART6_NUMBER, STM32_UART_USART6_IRQ_PRIORITY);
      uartp->dmamode |= STM32_DMA_CR_CHSEL(USART6_RX_DMA_CHANNEL) |
                        STM32_DMA_CR_PL(STM32_UART_USART6_DMA_PRIORITY);
    }
#endif

#if STM32_UART_USE_UART7
    if (&UARTD7 == uartp) {
      bool b;
      b = dmaStreamAllocate(uartp->dmarx,
                            STM32_UART_UART7_IRQ_PRIORITY,
                            (stm32_dmaisr_t)uart_lld_serve_rx_end_irq,
                            (void *)uartp);
      osalDbgAssert(!b, "stream already allocated");
      b = dmaStreamAllocate(uartp->dmatx,
                            STM32_UART_UART7_IRQ_PRIORITY,
                            (stm32_dmaisr_t)uart_lld_serve_tx_end_irq,
                            (void *)uartp);
      osalDbgAssert(!b, "stream already allocated");
      rccEnableUART7(FALSE);
      nvicEnableVector(STM32_UART7_NUMBER, STM32_UART_UART7_IRQ_PRIORITY);
      uartp->dmamode |= STM32_DMA_CR_CHSEL(UART7_RX_DMA_CHANNEL) |
                        STM32_DMA_CR_PL(STM32_UART_UART7_DMA_PRIORITY);
    }
#endif

#if STM32_UART_USE_UART8
    if (&UARTD8 == uartp) {
      bool b;
      b = dmaStreamAllocate(uartp->dmarx,
                            STM32_UART_UART8_IRQ_PRIORITY,
                            (stm32_dmaisr_t)uart_lld_serve_rx_end_irq,
                            (void *)uartp);
      osalDbgAssert(!b, "stream already allocated");
      b = dmaStreamAllocate(uartp->dmatx,
                            STM32_UART_UART8_IRQ_PRIORITY,
                            (stm32_dmaisr_t)uart_lld_serve_tx_end_irq,
                            (void *)uartp);
      osalDbgAssert(!b, "stream already allocated");
      rccEnableUART8(FALSE);
      nvicEnableVector(STM32_UART8_NUMBER, STM32_UART_UART8_IRQ_PRIORITY);
      uartp->dmamode |= STM32_DMA_CR_CHSEL(UART8_RX_DMA_CHANNEL) |
                        STM32_DMA_CR_PL(STM32_UART_UART8_DMA_PRIORITY);
    }
#endif

    /* Static DMA setup, the transfer size depends on the USART settings,
       it is 16 bits if M=1 and PCE=0 else it is 8 bits.*/
    if ((uartp->config->cr1 & (USART_CR1_M | USART_CR1_PCE)) == USART_CR1_M)
      uartp->dmamode |= STM32_DMA_CR_PSIZE_HWORD | STM32_DMA_CR_MSIZE_HWORD;
    dmaStreamSetPeripheral(uartp->dmarx, &uartp->usart->RDR);
    dmaStreamSetPeripheral(uartp->dmatx, &uartp->usart->TDR);
    uartp->rxbuf = 0;
  }

  uartp->rxstate = UART_RX_IDLE;
  uartp->txstate = UART_TX_IDLE;
  usart_start(uartp);
}
Ejemplo n.º 4
0
/**
 * @brief   Configures and activates the UART peripheral.
 *
 * @param[in] uartp     pointer to the @p UARTDriver object
 *
 * @notapi
 */
void uart_lld_start(UARTDriver *uartp) {

  if (uartp->state == UART_STOP) {
#if STM32_UART_USE_USART1
    if (&UARTD1 == uartp) {
      bool_t b;
      b = dmaStreamAllocate(uartp->dmarx,
                            STM32_UART_USART1_IRQ_PRIORITY,
                            (stm32_dmaisr_t)uart_lld_serve_rx_end_irq,
                            (void *)uartp);
      chDbgAssert(!b, "uart_lld_start(), #1", "stream already allocated");
      b = dmaStreamAllocate(uartp->dmatx,
                            STM32_UART_USART1_IRQ_PRIORITY,
                            (stm32_dmaisr_t)uart_lld_serve_tx_end_irq,
                            (void *)uartp);
      chDbgAssert(!b, "uart_lld_start(), #2", "stream already allocated");
      rccEnableUSART1(FALSE);
      nvicEnableVector(STM32_USART1_NUMBER,
                       CORTEX_PRIORITY_MASK(STM32_UART_USART1_IRQ_PRIORITY));
      uartp->dmamode |= STM32_DMA_CR_CHSEL(USART1_RX_DMA_CHANNEL) |
                        STM32_DMA_CR_PL(STM32_UART_USART1_DMA_PRIORITY);
    }
#endif

#if STM32_UART_USE_USART2
    if (&UARTD2 == uartp) {
      bool_t b;
      b = dmaStreamAllocate(uartp->dmarx,
                            STM32_UART_USART2_IRQ_PRIORITY,
                            (stm32_dmaisr_t)uart_lld_serve_rx_end_irq,
                            (void *)uartp);
      chDbgAssert(!b, "uart_lld_start(), #3", "stream already allocated");
      b = dmaStreamAllocate(uartp->dmatx,
                            STM32_UART_USART2_IRQ_PRIORITY,
                            (stm32_dmaisr_t)uart_lld_serve_tx_end_irq,
                            (void *)uartp);
      chDbgAssert(!b, "uart_lld_start(), #4", "stream already allocated");
      rccEnableUSART2(FALSE);
      nvicEnableVector(STM32_USART2_NUMBER,
                       CORTEX_PRIORITY_MASK(STM32_UART_USART2_IRQ_PRIORITY));
      uartp->dmamode |= STM32_DMA_CR_CHSEL(USART2_RX_DMA_CHANNEL) |
                        STM32_DMA_CR_PL(STM32_UART_USART2_DMA_PRIORITY);
    }
#endif

#if STM32_UART_USE_USART3
    if (&UARTD3 == uartp) {
      bool_t b;
      b = dmaStreamAllocate(uartp->dmarx,
                            STM32_UART_USART3_IRQ_PRIORITY,
                            (stm32_dmaisr_t)uart_lld_serve_rx_end_irq,
                            (void *)uartp);
      chDbgAssert(!b, "uart_lld_start(), #5", "stream already allocated");
      b = dmaStreamAllocate(uartp->dmatx,
                            STM32_UART_USART3_IRQ_PRIORITY,
                            (stm32_dmaisr_t)uart_lld_serve_tx_end_irq,
                            (void *)uartp);
      chDbgAssert(!b, "uart_lld_start(), #6", "stream already allocated");
      rccEnableUSART3(FALSE);
      nvicEnableVector(STM32_USART3_NUMBER,
                       CORTEX_PRIORITY_MASK(STM32_UART_USART3_IRQ_PRIORITY));
      uartp->dmamode |= STM32_DMA_CR_CHSEL(USART3_RX_DMA_CHANNEL) |
                        STM32_DMA_CR_PL(STM32_UART_USART3_DMA_PRIORITY);
    }
#endif

#if STM32_UART_USE_UART4
    if (&UARTD4 == uartp) {
      bool_t b;

      chDbgAssert((uartp->config->cr2 & STM32_UART45_CR2_CHECK_MASK) == 0,
                  "uart_lld_start(), #7",
                  "specified invalid bits in UART4 CR2 register settings");
      chDbgAssert((uartp->config->cr3 & STM32_UART45_CR3_CHECK_MASK) == 0,
                  "uart_lld_start(), #8",
                  "specified invalid bits in UART4 CR3 register settings");

      b = dmaStreamAllocate(uartp->dmarx,
                            STM32_UART_UART4_IRQ_PRIORITY,
                            (stm32_dmaisr_t)uart_lld_serve_rx_end_irq,
                            (void *)uartp);
      chDbgAssert(!b, "uart_lld_start(), #9", "stream already allocated");
      b = dmaStreamAllocate(uartp->dmatx,
                            STM32_UART_UART4_IRQ_PRIORITY,
                            (stm32_dmaisr_t)uart_lld_serve_tx_end_irq,
                            (void *)uartp);
      chDbgAssert(!b, "uart_lld_start(), #10", "stream already allocated");
      rccEnableUART4(FALSE);
      nvicEnableVector(STM32_UART4_NUMBER,
                       CORTEX_PRIORITY_MASK(STM32_UART_UART4_IRQ_PRIORITY));
      uartp->dmamode |= STM32_DMA_CR_CHSEL(UART4_RX_DMA_CHANNEL) |
                        STM32_DMA_CR_PL(STM32_UART_UART4_DMA_PRIORITY);
    }
#endif

#if STM32_UART_USE_UART5
    if (&UARTD5 == uartp) {
      bool_t b;

      chDbgAssert((uartp->config->cr2 & STM32_UART45_CR2_CHECK_MASK) == 0,
                  "uart_lld_start(), #11",
                  "specified invalid bits in UART5 CR2 register settings");
      chDbgAssert((uartp->config->cr3 & STM32_UART45_CR3_CHECK_MASK) == 0,
                  "uart_lld_start(), #12",
                  "specified invalid bits in UART5 CR3 register settings");

      b = dmaStreamAllocate(uartp->dmarx,
                            STM32_UART_UART5_IRQ_PRIORITY,
                            (stm32_dmaisr_t)uart_lld_serve_rx_end_irq,
                            (void *)uartp);
      chDbgAssert(!b, "uart_lld_start(), #13", "stream already allocated");
      b = dmaStreamAllocate(uartp->dmatx,
                            STM32_UART_UART5_IRQ_PRIORITY,
                            (stm32_dmaisr_t)uart_lld_serve_tx_end_irq,
                            (void *)uartp);
      chDbgAssert(!b, "uart_lld_start(), #14", "stream already allocated");
      rccEnableUART5(FALSE);
      nvicEnableVector(STM32_UART5_NUMBER,
                       CORTEX_PRIORITY_MASK(STM32_UART_UART5_IRQ_PRIORITY));
      uartp->dmamode |= STM32_DMA_CR_CHSEL(UART5_RX_DMA_CHANNEL) |
                        STM32_DMA_CR_PL(STM32_UART_UART5_DMA_PRIORITY);
    }
#endif

#if STM32_UART_USE_USART6
    if (&UARTD6 == uartp) {
      bool_t b;
      b = dmaStreamAllocate(uartp->dmarx,
                            STM32_UART_USART6_IRQ_PRIORITY,
                            (stm32_dmaisr_t)uart_lld_serve_rx_end_irq,
                            (void *)uartp);
      chDbgAssert(!b, "uart_lld_start(), #15", "stream already allocated");
      b = dmaStreamAllocate(uartp->dmatx,
                            STM32_UART_USART6_IRQ_PRIORITY,
                            (stm32_dmaisr_t)uart_lld_serve_tx_end_irq,
                            (void *)uartp);
      chDbgAssert(!b, "uart_lld_start(), #16", "stream already allocated");
      rccEnableUSART6(FALSE);
      nvicEnableVector(STM32_USART6_NUMBER,
                       CORTEX_PRIORITY_MASK(STM32_UART_USART6_IRQ_PRIORITY));
      uartp->dmamode |= STM32_DMA_CR_CHSEL(USART6_RX_DMA_CHANNEL) |
                        STM32_DMA_CR_PL(STM32_UART_USART6_DMA_PRIORITY);
    }
#endif

    /* Static DMA setup, the transfer size depends on the USART settings,
       it is 16 bits if M=1 and PCE=0 else it is 8 bits.*/
    if ((uartp->config->cr1 & (USART_CR1_M | USART_CR1_PCE)) == USART_CR1_M)
      uartp->dmamode |= STM32_DMA_CR_PSIZE_HWORD | STM32_DMA_CR_MSIZE_HWORD;
    dmaStreamSetPeripheral(uartp->dmarx, &uartp->usart->DR);
    dmaStreamSetPeripheral(uartp->dmatx, &uartp->usart->DR);
    uartp->rxbuf = 0;
  }

  uartp->rxstate = UART_RX_IDLE;
  uartp->txstate = UART_TX_IDLE;
  usart_start(uartp);
}