void EEPROM::update(GCode *com)
{
#if EEPROM_MODE!=0
if(com->hasT() && com->hasP()) switch(com->T)
{
case 0:
if(com->hasS()) HAL::epr_set_byte(com->P,(byte)com->S);
break;
case 1:
if(com->hasS()) HAL::epr_set_int(com->P,(int)com->S);
break;
case 2:
if(com->hasS()) HAL::epr_set_long(com->P,(long)com->S);
break;
case 3:
if(com->hasX()) HAL::epr_set_float(com->P,com->X);
break;
}
byte newcheck = computeChecksum();
if(newcheck!=HAL::epr_get_byte(EPR_INTEGRITY_BYTE))
HAL::epr_set_byte(EPR_INTEGRITY_BYTE,newcheck);
readDataFromEEPROM();
#else
Com::printErrorF(tNoEEPROMSupport);
#endif
}
void EEPROM::update(GCode *com)
{
#if EEPROM_MODE!=0
if(com->hasT() && com->hasP()) switch(com->T)
{
case 0:
if(com->hasS()) HAL::eprSetByte(com->P,(uint8_t)com->S);
break;
case 1:
if(com->hasS()) HAL::eprSetInt16(com->P,(int)com->S);
break;
case 2:
if(com->hasS()) HAL::eprSetInt32(com->P,(long)com->S);
break;
case 3:
if(com->hasX()) HAL::eprSetFloat(com->P,com->X);
break;
}
uint8_t newcheck = computeChecksum();
if(newcheck!=HAL::eprGetByte(EPR_INTEGRITY_BYTE))
HAL::eprSetByte(EPR_INTEGRITY_BYTE,newcheck);
readDataFromEEPROM();
Extruder::selectExtruderById(Extruder::current->id);
#else
Com::printErrorF(Com::tNoEEPROMSupport);
#endif
}
void EEPROM::init()
{
#if EEPROM_MODE != 0
uint8_t check = computeChecksum();
uint8_t storedcheck = HAL::eprGetByte(EPR_INTEGRITY_BYTE);
if(HAL::eprGetByte(EPR_MAGIC_BYTE) == EEPROM_MODE && storedcheck == check)
{
readDataFromEEPROM();
if (USE_CONFIGURATION_BAUD_RATE)
{
// Used if eeprom gets unusable baud rate set and communication wont work at all.
if(HAL::eprGetInt32(EPR_BAUDRATE) != BAUDRATE)
{
HAL::eprSetInt32(EPR_BAUDRATE,BAUDRATE);
baudrate = BAUDRATE;
uint8_t newcheck = computeChecksum();
if(newcheck != HAL::eprGetByte(EPR_INTEGRITY_BYTE))
HAL::eprSetByte(EPR_INTEGRITY_BYTE,newcheck);
}
Com::printFLN(PSTR("EEprom baud rate restored from configuration."));
Com::printFLN(PSTR("RECOMPILE WITH USE_CONFIGURATION_BAUD_RATE == 0 to alter baud rate via EEPROM"));
}
}
else
{
HAL::eprSetByte(EPR_MAGIC_BYTE,EEPROM_MODE); // Make datachange permanent
initalizeUncached();
storeDataIntoEEPROM(storedcheck != check);
}
#endif
}
//internal usage of update value
void EEPROM:: update(long P,uint8_t T,long S,float X)
{
#if EEPROM_MODE!=0
if(T>=0 &&T<=3 && P>0 && P<=2048) //SDEEPROM_SIZE =2048 // Minimum size used by Eeprom.cpp
switch(T)
{
case EPR_TYPE_BYTE:
HAL::eprSetByte(P,(uint8_t)S);
break;
case EPR_TYPE_INT:
HAL::eprSetInt16(P,(int)S);
break;
case EPR_TYPE_LONG:
HAL::eprSetInt32(P,(int32_t)S);
break;
case EPR_TYPE_FLOAT:
HAL::eprSetFloat(P,X);
break;
}
uint8_t newcheck = computeChecksum();
if(newcheck != HAL::eprGetByte(EPR_INTEGRITY_BYTE))
HAL::eprSetByte(EPR_INTEGRITY_BYTE,newcheck);
readDataFromEEPROM();
Extruder::selectExtruderById(Extruder::current->id);
#else
Com::printErrorF(Com::tNoEEPROMSupport);
#endif
}
void EEPROM::init()
{
#if EEPROM_MODE!=0
byte check = computeChecksum();
byte storedcheck = HAL::epr_get_byte(EPR_INTEGRITY_BYTE);
if(HAL::epr_get_byte(EPR_MAGIC_BYTE)==EEPROM_MODE && storedcheck==check)
{
readDataFromEEPROM();
}
else
{
HAL::epr_set_byte(EPR_MAGIC_BYTE,EEPROM_MODE); // Make datachange permanent
storeDataIntoEEPROM(storedcheck!=check);
}
#endif
}
void EEPROM::init()
{
#if EEPROM_MODE!=0
uint8_t check = computeChecksum();
uint8_t storedcheck = HAL::eprGetByte(EPR_INTEGRITY_BYTE);
if(HAL::eprGetByte(EPR_MAGIC_BYTE)==EEPROM_MODE && storedcheck==check)
{
readDataFromEEPROM();
}
else
{
HAL::eprSetByte(EPR_MAGIC_BYTE,EEPROM_MODE); // Make datachange permanent
initalizeUncached();
storeDataIntoEEPROM(storedcheck!=check);
}
#endif
}
void EEPROM::update(GCode *com)
{
#if EEPROM_MODE != 0
if(com->hasT() && com->hasP()) switch(com->T)
{
case 0:
if(com->hasS())
HAL::eprSetByte(com->P, (uint8_t)com->S);
break;
case 1:
if(com->hasS())
HAL::eprSetInt16(com->P, (int16_t)com->S);
break;
case 2:
if(com->hasS())
HAL::eprSetInt32(com->P, (int32_t)com->S);
break;
case 3:
if(com->hasX())
HAL::eprSetFloat(com->P, com->X);
break;
}
uint8_t newcheck = computeChecksum();
if(newcheck != HAL::eprGetByte(EPR_INTEGRITY_BYTE))
HAL::eprSetByte(EPR_INTEGRITY_BYTE, newcheck);
bool includesEeprom = com->P >= EEPROM_EXTRUDER_OFFSET && com->P < EEPROM_EXTRUDER_OFFSET + 6 * EEPROM_EXTRUDER_LENGTH;
readDataFromEEPROM(includesEeprom);
#if MIXING_EXTRUDER
Extruder::selectExtruderById(Extruder::activeMixingExtruder);
#else
Extruder::selectExtruderById(Extruder::current->id);
#endif
#else
Com::printErrorF(Com::tNoEEPROMSupport);
#endif
}
