int
user_start(int argc, char *argv[])
{
/* run C++ ctors before we go any further */
up_cxxinitialize();
/* reset all to zero */
memset(&system_state, 0, sizeof(system_state));
/* configure the high-resolution time/callout interface */
hrt_init();
/* calculate our fw CRC so FMU can decide if we need to update */
calculate_fw_crc();
/*
* Poll at 1ms intervals for received bytes that have not triggered
* a DMA event.
*/
#ifdef CONFIG_ARCH_DMA
hrt_call_every(&serial_dma_call, 1000, 1000, (hrt_callout)stm32_serial_dma_poll, NULL);
#endif
/* print some startup info */
lowsyslog("\nPX4IO: starting\n");
/* default all the LEDs to off while we start */
LED_AMBER(false);
LED_BLUE(false);
LED_SAFETY(false);
#ifdef GPIO_LED4
LED_RING(false);
#endif
/* turn on servo power (if supported) */
#ifdef POWER_SERVO
POWER_SERVO(true);
#endif
/* turn off S.Bus out (if supported) */
#ifdef ENABLE_SBUS_OUT
ENABLE_SBUS_OUT(false);
#endif
/* start the safety switch handler */
safety_init();
/* configure the first 8 PWM outputs (i.e. all of them) */
up_pwm_servo_init(0xff);
/* initialise the control inputs */
controls_init();
/* set up the ADC */
adc_init();
/* start the FMU interface */
interface_init();
/* add a performance counter for mixing */
perf_counter_t mixer_perf = perf_alloc(PC_ELAPSED, "mix");
/* add a performance counter for controls */
perf_counter_t controls_perf = perf_alloc(PC_ELAPSED, "controls");
/* and one for measuring the loop rate */
perf_counter_t loop_perf = perf_alloc(PC_INTERVAL, "loop");
struct mallinfo minfo = mallinfo();
lowsyslog("MEM: free %u, largest %u\n", minfo.mxordblk, minfo.fordblks);
/* initialize PWM limit lib */
pwm_limit_init(&pwm_limit);
/*
* P O L I C E L I G H T S
*
* Not enough memory, lock down.
*
* We might need to allocate mixers later, and this will
* ensure that a developer doing a change will notice
* that he just burned the remaining RAM with static
* allocations. We don't want him to be able to
* get past that point. This needs to be clearly
* documented in the dev guide.
*
*/
if (minfo.mxordblk < 600) {
lowsyslog("ERR: not enough MEM");
bool phase = false;
while (true) {
if (phase) {
LED_AMBER(true);
LED_BLUE(false);
} else {
LED_AMBER(false);
LED_BLUE(true);
}
up_udelay(250000);
phase = !phase;
}
}
/* Start the failsafe led init */
failsafe_led_init();
/*
* Run everything in a tight loop.
*/
uint64_t last_debug_time = 0;
uint64_t last_heartbeat_time = 0;
for (;;) {
/* track the rate at which the loop is running */
perf_count(loop_perf);
/* kick the mixer */
perf_begin(mixer_perf);
mixer_tick();
perf_end(mixer_perf);
/* kick the control inputs */
perf_begin(controls_perf);
controls_tick();
perf_end(controls_perf);
if ((hrt_absolute_time() - last_heartbeat_time) > 250 * 1000) {
last_heartbeat_time = hrt_absolute_time();
heartbeat_blink();
}
ring_blink();
check_reboot();
/* check for debug activity (default: none) */
show_debug_messages();
/* post debug state at ~1Hz - this is via an auxiliary serial port
* DEFAULTS TO OFF!
*/
if (hrt_absolute_time() - last_debug_time > (1000 * 1000)) {
isr_debug(1, "d:%u s=0x%x a=0x%x f=0x%x m=%u",
(unsigned)r_page_setup[PX4IO_P_SETUP_SET_DEBUG],
(unsigned)r_status_flags,
(unsigned)r_setup_arming,
(unsigned)r_setup_features,
(unsigned)mallinfo().mxordblk);
last_debug_time = hrt_absolute_time();
}
}
}
int
user_start(int argc, char *argv[])
{
/* configure the first 8 PWM outputs (i.e. all of them) */
up_pwm_servo_init(0xff);
#if defined(CONFIG_HAVE_CXX) && defined(CONFIG_HAVE_CXXINITIALIZE)
/* run C++ ctors before we go any further */
up_cxxinitialize();
# if defined(CONFIG_EXAMPLES_NSH_CXXINITIALIZE)
# error CONFIG_EXAMPLES_NSH_CXXINITIALIZE Must not be defined! Use CONFIG_HAVE_CXX and CONFIG_HAVE_CXXINITIALIZE.
# endif
#else
# error platform is dependent on c++ both CONFIG_HAVE_CXX and CONFIG_HAVE_CXXINITIALIZE must be defined.
#endif
/* reset all to zero */
memset(&system_state, 0, sizeof(system_state));
/* configure the high-resolution time/callout interface */
hrt_init();
/* calculate our fw CRC so FMU can decide if we need to update */
calculate_fw_crc();
/*
* Poll at 1ms intervals for received bytes that have not triggered
* a DMA event.
*/
#ifdef CONFIG_ARCH_DMA
hrt_call_every(&serial_dma_call, 1000, 1000, (hrt_callout)stm32_serial_dma_poll, NULL);
#endif
/* print some startup info */
syslog(LOG_INFO, "\nPX4IO: starting\n");
/* default all the LEDs to off while we start */
LED_AMBER(false);
LED_BLUE(false);
LED_SAFETY(false);
#ifdef GPIO_LED4
LED_RING(false);
#endif
/* turn on servo power (if supported) */
#ifdef POWER_SERVO
POWER_SERVO(true);
#endif
/* turn off S.Bus out (if supported) */
#ifdef ENABLE_SBUS_OUT
ENABLE_SBUS_OUT(false);
#endif
/* start the safety switch handler */
safety_init();
/* initialise the control inputs */
controls_init();
/* set up the ADC */
adc_init();
/* start the FMU interface */
interface_init();
/* add a performance counter for mixing */
perf_counter_t mixer_perf = perf_alloc(PC_ELAPSED, "mix");
/* add a performance counter for controls */
perf_counter_t controls_perf = perf_alloc(PC_ELAPSED, "controls");
/* and one for measuring the loop rate */
perf_counter_t loop_perf = perf_alloc(PC_INTERVAL, "loop");
struct mallinfo minfo = mallinfo();
r_page_status[PX4IO_P_STATUS_FREEMEM] = minfo.mxordblk;
syslog(LOG_INFO, "MEM: free %u, largest %u\n", minfo.mxordblk, minfo.fordblks);
/* initialize PWM limit lib */
pwm_limit_init(&pwm_limit);
/*
* P O L I C E L I G H T S
*
* Not enough memory, lock down.
*
* We might need to allocate mixers later, and this will
* ensure that a developer doing a change will notice
* that he just burned the remaining RAM with static
* allocations. We don't want him to be able to
* get past that point. This needs to be clearly
* documented in the dev guide.
*
*/
if (minfo.mxordblk < 600) {
syslog(LOG_ERR, "ERR: not enough MEM");
bool phase = false;
while (true) {
if (phase) {
LED_AMBER(true);
LED_BLUE(false);
} else {
LED_AMBER(false);
LED_BLUE(true);
}
up_udelay(250000);
phase = !phase;
}
}
/* Start the failsafe led init */
failsafe_led_init();
/*
* Run everything in a tight loop.
*/
uint64_t last_debug_time = 0;
uint64_t last_heartbeat_time = 0;
uint64_t last_loop_time = 0;
for (;;) {
dt = (hrt_absolute_time() - last_loop_time) / 1000000.0f;
last_loop_time = hrt_absolute_time();
if (dt < 0.0001f) {
dt = 0.0001f;
} else if (dt > 0.02f) {
dt = 0.02f;
}
/* track the rate at which the loop is running */
perf_count(loop_perf);
/* kick the mixer */
perf_begin(mixer_perf);
mixer_tick();
perf_end(mixer_perf);
/* kick the control inputs */
perf_begin(controls_perf);
controls_tick();
perf_end(controls_perf);
/* some boards such as Pixhawk 2.1 made
the unfortunate choice to combine the blue led channel with
the IMU heater. We need a software hack to fix the hardware hack
by allowing to disable the LED / heater.
*/
if (r_page_setup[PX4IO_P_SETUP_THERMAL] == PX4IO_THERMAL_IGNORE) {
/*
blink blue LED at 4Hz in normal operation. When in
override blink 4x faster so the user can clearly see
that override is happening. This helps when
pre-flight testing the override system
*/
uint32_t heartbeat_period_us = 250 * 1000UL;
if (r_status_flags & PX4IO_P_STATUS_FLAGS_OVERRIDE) {
heartbeat_period_us /= 4;
}
if ((hrt_absolute_time() - last_heartbeat_time) > heartbeat_period_us) {
last_heartbeat_time = hrt_absolute_time();
heartbeat_blink();
}
} else if (r_page_setup[PX4IO_P_SETUP_THERMAL] < PX4IO_THERMAL_FULL) {
/* switch resistive heater off */
LED_BLUE(false);
} else {
/* switch resistive heater hard on */
LED_BLUE(true);
}
update_mem_usage();
ring_blink();
check_reboot();
/* check for debug activity (default: none) */
show_debug_messages();
/* post debug state at ~1Hz - this is via an auxiliary serial port
* DEFAULTS TO OFF!
*/
if (hrt_absolute_time() - last_debug_time > (1000 * 1000)) {
isr_debug(1, "d:%u s=0x%x a=0x%x f=0x%x m=%u",
(unsigned)r_page_setup[PX4IO_P_SETUP_SET_DEBUG],
(unsigned)r_status_flags,
(unsigned)r_setup_arming,
(unsigned)r_setup_features,
(unsigned)mallinfo().mxordblk);
last_debug_time = hrt_absolute_time();
}
}
}