void rt2x00mac_bss_info_changed(struct ieee80211_hw *hw,
struct ieee80211_vif *vif,
struct ieee80211_bss_conf *bss_conf,
u32 changes)
{
struct rt2x00_dev *rt2x00dev = hw->priv;
struct rt2x00_intf *intf = vif_to_intf(vif);
/*
* mac80211 might be calling this function while we are trying
* to remove the device or perhaps suspending it.
*/
if (!test_bit(DEVICE_STATE_PRESENT, &rt2x00dev->flags))
return;
/*
* Update the BSSID.
*/
if (changes & BSS_CHANGED_BSSID)
rt2x00lib_config_intf(rt2x00dev, intf, vif->type, NULL,
bss_conf->bssid);
/*
* Start/stop beaconing.
*/
if (changes & BSS_CHANGED_BEACON_ENABLED) {
if (!bss_conf->enable_beacon && intf->enable_beacon) {
rt2x00dev->intf_beaconing--;
intf->enable_beacon = false;
/*
* Clear beacon in the H/W for this vif. This is needed
* to disable beaconing on this particular interface
* and keep it running on other interfaces.
*/
rt2x00queue_clear_beacon(rt2x00dev, vif);
if (rt2x00dev->intf_beaconing == 0) {
/*
* Last beaconing interface disabled
* -> stop beacon queue.
*/
mutex_lock(&intf->beacon_skb_mutex);
rt2x00queue_stop_queue(rt2x00dev->bcn);
mutex_unlock(&intf->beacon_skb_mutex);
}
} else if (bss_conf->enable_beacon && !intf->enable_beacon) {
rt2x00dev->intf_beaconing++;
intf->enable_beacon = true;
/*
* Upload beacon to the H/W. This is only required on
* USB devices. PCI devices fetch beacons periodically.
*/
if (rt2x00_is_usb(rt2x00dev))
rt2x00queue_update_beacon(rt2x00dev, vif);
if (rt2x00dev->intf_beaconing == 1) {
/*
* First beaconing interface enabled
* -> start beacon queue.
*/
mutex_lock(&intf->beacon_skb_mutex);
rt2x00queue_start_queue(rt2x00dev->bcn);
mutex_unlock(&intf->beacon_skb_mutex);
}
}
}
/*
* When the association status has changed we must reset the link
* tuner counter. This is because some drivers determine if they
* should perform link tuning based on the number of seconds
* while associated or not associated.
*/
if (changes & BSS_CHANGED_ASSOC) {
rt2x00dev->link.count = 0;
if (bss_conf->assoc)
rt2x00dev->intf_associated++;
else
rt2x00dev->intf_associated--;
rt2x00leds_led_assoc(rt2x00dev, !!rt2x00dev->intf_associated);
clear_bit(CONFIG_QOS_DISABLED, &rt2x00dev->flags);
}
/*
* Check for access point which do not support 802.11e . We have to
* generate data frames sequence number in S/W for such AP, because
* of H/W bug.
*/
if (changes & BSS_CHANGED_QOS && !bss_conf->qos)
set_bit(CONFIG_QOS_DISABLED, &rt2x00dev->flags);
/*
* When the erp information has changed, we should perform
* additional configuration steps. For all other changes we are done.
*/
if (changes & (BSS_CHANGED_ERP_CTS_PROT | BSS_CHANGED_ERP_PREAMBLE |
BSS_CHANGED_ERP_SLOT | BSS_CHANGED_BASIC_RATES |
BSS_CHANGED_BEACON_INT | BSS_CHANGED_HT))
rt2x00lib_config_erp(rt2x00dev, intf, bss_conf, changes);
}
void rt2x00mac_bss_info_changed(struct ieee80211_hw *hw,
struct ieee80211_vif *vif,
struct ieee80211_bss_conf *bss_conf,
u32 changes)
{
struct rt2x00_dev *rt2x00dev = hw->priv;
struct rt2x00_intf *intf = vif_to_intf(vif);
/*
* mac80211 might be calling this function while we are trying
* to remove the device or perhaps suspending it.
*/
if (!test_bit(DEVICE_STATE_PRESENT, &rt2x00dev->flags))
return;
spin_lock(&intf->lock);
/*
* conf->bssid can be NULL if coming from the internal
* beacon update routine.
*/
if (changes & BSS_CHANGED_BSSID)
memcpy(&intf->bssid, bss_conf->bssid, ETH_ALEN);
spin_unlock(&intf->lock);
/*
* Call rt2x00_config_intf() outside of the spinlock context since
* the call will sleep for USB drivers. By using the ieee80211_if_conf
* values as arguments we make keep access to rt2x00_intf thread safe
* even without the lock.
*/
if (changes & BSS_CHANGED_BSSID)
rt2x00lib_config_intf(rt2x00dev, intf, vif->type, NULL,
bss_conf->bssid);
/*
* Update the beacon.
*/
if (changes & (BSS_CHANGED_BEACON | BSS_CHANGED_BEACON_ENABLED))
rt2x00queue_update_beacon(rt2x00dev, vif,
bss_conf->enable_beacon);
/*
* When the association status has changed we must reset the link
* tuner counter. This is because some drivers determine if they
* should perform link tuning based on the number of seconds
* while associated or not associated.
*/
if (changes & BSS_CHANGED_ASSOC) {
rt2x00dev->link.count = 0;
if (bss_conf->assoc)
rt2x00dev->intf_associated++;
else
rt2x00dev->intf_associated--;
rt2x00leds_led_assoc(rt2x00dev, !!rt2x00dev->intf_associated);
}
/*
* When the erp information has changed, we should perform
* additional configuration steps. For all other changes we are done.
*/
if (changes & (BSS_CHANGED_ERP_CTS_PROT | BSS_CHANGED_ERP_PREAMBLE |
BSS_CHANGED_ERP_SLOT | BSS_CHANGED_BASIC_RATES |
BSS_CHANGED_BEACON_INT | BSS_CHANGED_HT))
rt2x00lib_config_erp(rt2x00dev, intf, bss_conf, changes);
}