void init_TSC(void) { u_int64_t tscval[2]; if (bootverbose) printf("Calibrating TSC clock ... "); tscval[0] = rdtsc(); DELAY(1000000); tscval[1] = rdtsc(); tsc_freq = tscval[1] - tscval[0]; if (bootverbose) printf("TSC clock: %lu Hz\n", tsc_freq); /* * Inform CPU accounting about our boot-time clock rate. Once the * system is finished booting, we will get the real max clock rate * via tsc_freq_max(). This also will be updated if someone loads * a cpufreq driver after boot that discovers a new max frequency. */ set_cputicker(rdtsc, tsc_freq, 1); /* Register to find out about changes in CPU frequency. */ tsc_pre_tag = EVENTHANDLER_REGISTER(cpufreq_pre_change, tsc_freq_changing, NULL, EVENTHANDLER_PRI_FIRST); tsc_post_tag = EVENTHANDLER_REGISTER(cpufreq_post_change, tsc_freq_changed, NULL, EVENTHANDLER_PRI_FIRST); tsc_levels_tag = EVENTHANDLER_REGISTER(cpufreq_levels_changed, tsc_levels_changed, NULL, EVENTHANDLER_PRI_ANY); }
/* * When cpufreq levels change, find out about the (new) max frequency. We * use this to update CPU accounting in case it got a lower estimate at boot. */ static void tsc_levels_changed(void *arg, int unit) { device_t cf_dev; struct cf_level *levels; int count, error; uint64_t max_freq; /* Only use values from the first CPU, assuming all are equal. */ if (unit != 0) return; /* Find the appropriate cpufreq device instance. */ cf_dev = devclass_get_device(devclass_find("cpufreq"), unit); if (cf_dev == NULL) { printf("tsc_levels_changed() called but no cpufreq device?\n"); return; } /* Get settings from the device and find the max frequency. */ count = 64; levels = malloc(count * sizeof(*levels), M_TEMP, M_NOWAIT); if (levels == NULL) return; error = CPUFREQ_LEVELS(cf_dev, levels, &count); if (error == 0 && count != 0) { max_freq = (uint64_t)levels[0].total_set.freq * 1000000; set_cputicker(rdtsc, max_freq, 1); } else printf("tsc_levels_changed: no max freq found\n"); free(levels, M_TEMP); }
void mips_timer_init_params(uint64_t platform_counter_freq, int double_count) { /* * XXX: Do not use printf here: uart code 8250 may use DELAY so this * function should be called before cninit. */ counter_freq = platform_counter_freq; /* * XXX: Some MIPS32 cores update the Count register only every two * pipeline cycles. * We know this because of status registers in CP0, make it automatic. */ if (double_count != 0) counter_freq /= 2; cycles_per_usec = counter_freq / (1 * 1000 * 1000); set_cputicker(tick_ticker, counter_freq, 1); }
void platform_start(__register_t a0, __register_t a1, __register_t a2 __unused, __register_t a3) { const struct octeon_feature_description *ofd; uint64_t platform_counter_freq; int rv; mips_postboot_fixup(); /* * Initialize boot parameters so that we can determine things like * which console we shoud use, etc. */ octeon_boot_params_init(a3); /* Initialize pcpu stuff */ mips_pcpu0_init(); mips_timer_early_init(cvmx_sysinfo_get()->cpu_clock_hz); /* Initialize console. */ cninit(); /* * Display information about the CPU. */ #if !defined(OCTEON_MODEL) printf("Using runtime CPU model checks.\n"); #else printf("Compiled for CPU model: " __XSTRING(OCTEON_MODEL) "\n"); #endif strcpy(cpu_model, octeon_model_get_string(cvmx_get_proc_id())); printf("CPU Model: %s\n", cpu_model); printf("CPU clock: %uMHz Core Mask: %#x\n", cvmx_sysinfo_get()->cpu_clock_hz / 1000000, cvmx_sysinfo_get()->core_mask); rv = octeon_model_version_check(cvmx_get_proc_id()); if (rv == -1) panic("%s: kernel not compatible with this processor.", __func__); /* * Display information about the board. */ #if defined(OCTEON_BOARD_CAPK_0100ND) strcpy(cpu_board, "CAPK-0100ND"); if (cvmx_sysinfo_get()->board_type != CVMX_BOARD_TYPE_CN3010_EVB_HS5) { panic("Compiled for %s, but board type is %s.", cpu_board, cvmx_board_type_to_string(cvmx_sysinfo_get()->board_type)); } #else strcpy(cpu_board, cvmx_board_type_to_string(cvmx_sysinfo_get()->board_type)); #endif printf("Board: %s\n", cpu_board); printf("Board Type: %u Revision: %u/%u\n", cvmx_sysinfo_get()->board_type, cvmx_sysinfo_get()->board_rev_major, cvmx_sysinfo_get()->board_rev_minor); printf("Serial number: %s\n", cvmx_sysinfo_get()->board_serial_number); /* * Additional on-chip hardware/settings. * * XXX Display PCI host/target? What else? */ printf("MAC address base: %6D (%u configured)\n", cvmx_sysinfo_get()->mac_addr_base, ":", cvmx_sysinfo_get()->mac_addr_count); octeon_ciu_reset(); /* * Convert U-Boot 'bootoctlinux' loader command line arguments into * boot flags and kernel environment variables. */ bootverbose = 1; octeon_init_kenv(a3); /* * For some reason on the cn38xx simulator ebase register is set to * 0x80001000 at bootup time. Move it back to the default, but * when we move to having support for multiple executives, we need * to rethink this. */ mips_wr_ebase(0x80000000); octeon_memory_init(); init_param1(); init_param2(physmem); mips_cpu_init(); pmap_bootstrap(); mips_proc0_init(); mutex_init(); kdb_init(); #ifdef KDB if (boothowto & RB_KDB) kdb_enter(KDB_WHY_BOOTFLAGS, "Boot flags requested debugger"); #endif cpu_clock = cvmx_sysinfo_get()->cpu_clock_hz; platform_counter_freq = cpu_clock; octeon_timecounter.tc_frequency = cpu_clock; platform_timecounter = &octeon_timecounter; mips_timer_init_params(platform_counter_freq, 0); set_cputicker(octeon_get_ticks, cpu_clock, 0); #ifdef SMP /* * Clear any pending IPIs. */ cvmx_write_csr(CVMX_CIU_MBOX_CLRX(0), 0xffffffff); #endif printf("Octeon SDK: %s\n", OCTEON_SDK_VERSION_STRING); printf("Available Octeon features:"); for (ofd = octeon_feature_descriptions; ofd->ofd_string != NULL; ofd++) if (octeon_has_feature(ofd->ofd_feature)) printf(" %s", ofd->ofd_string); printf("\n"); }