/**
****************************************************************************************
* @brief Enable pad's and peripheral clocks assuming that peripherals' power domain is down. The Uart and SPi clocks are set.
*
* @return void
****************************************************************************************
*/
void periph_init(void)
{
// Power up peripherals' power domain
SetBits16(PMU_CTRL_REG, PERIPH_SLEEP, 0);
while (!(GetWord16(SYS_STAT_REG) & PER_IS_UP)) ;
#if ES4_CODE
SetBits16(CLK_16M_REG,XTAL16_BIAS_SH_DISABLE, 1);
#endif
//rom patch
patch_func();
//Init pads
set_pad_functions();
#if (BLE_APP_PRESENT)
/*
* (Re)Initialize peripherals
i.e.
uart_init(UART_BAUDRATE_115K2, 3);
*/
#endif
// Enable the pads
SetBits16(SYS_CTRL_REG, PAD_LATCH_EN, 1);
}
/**
****************************************************************************************
* @brief Enable pad's and peripheral clocks assuming that peripherals' power domain is down.
*
* The Uart and SPi clocks are set.
****************************************************************************************
*/
void periph_init(void) // set i2c, spi, uart, uart2 serial clks
{
// Power up peripherals' power domain
SetBits16(PMU_CTRL_REG, PERIPH_SLEEP, 0);
while (!(GetWord16(SYS_STAT_REG) & PER_IS_UP)) ;
#if ES4_CODE
SetBits16(CLK_16M_REG,XTAL16_BIAS_SH_DISABLE, 1);
#endif
// Initialize UART component
SetBits16(CLK_PER_REG, UART1_ENABLE, 1); // enable clock - always @16MHz
// baudr=9-> 115k2
// mode=3-> no parity, 1 stop bit 8 data length
#ifdef UART_MEGABIT
uart_init(UART_BAUDRATE_1M, 3);
#else
uart_init(UART_BAUDRATE_115K2, 3);
#endif // UART_MEGABIT
SetBits16(CLK_PER_REG, SPI_ENABLE, 1); // enable clock
SetBits16(CLK_PER_REG, SPI_DIV, 1); // set divider to 1
//rom patch
patch_func();
//Init pads
set_pad_functions();
// Enable the pads
SetBits16(SYS_CTRL_REG, PAD_LATCH_EN, 1);
}
/**
****************************************************************************************
* @brief Enable pad's and peripheral clocks assuming that peripherals' power domain is down. The Uart and SPi clocks are set.
*
* @return void
****************************************************************************************
*/
void periph_init(void) // set i2c, spi, uart, uart2 serial clks
{
// Power up peripherals' power domain
SetBits16(PMU_CTRL_REG, PERIPH_SLEEP, 0);
while (!(GetWord16(SYS_STAT_REG) & PER_IS_UP)) ;
SetBits16(CLK_16M_REG,XTAL16_BIAS_SH_DISABLE, 1);
//rom patch
patch_func();
//Init pads
set_pad_functions();
#if (BLE_APP_PRESENT)
#if BLE_PROX_MONITOR
app_proxm_port_reinit(XCY_LED0_GPIO);
app_button_enable();
#elif BLE_FINDME_LOCATOR
app_button_enable();
#endif //BLE_PROX_REPORTER
#if BLE_BATTERY_SERVER
app_batt_port_reinit();
#endif //BLE_BATTERY_SERVER
#endif //BLE_APP_PRESENT
// Enable the pads
SetBits16(SYS_CTRL_REG, PAD_LATCH_EN, 1);
}
/**
****************************************************************************************
* @brief Callback function, called when external wakeup function is triggered.
*
* @return void.
****************************************************************************************
*/
void ext_wakeup_cb(void)
{
if (GetBits16(SYS_STAT_REG, PER_IS_DOWN)) {
// Return GPIO functionality from external wakeup GPIO
#if DEVELOPMENT_DEBUG
GPIO_reservations();
#endif
set_pad_functions();
}
SetBits32(GP_CONTROL_REG, BLE_WAKEUP_REQ, 1);
}
/**
****************************************************************************************
* @brief Enable pad's and peripheral clocks assuming that peripherals' power domain is down.
*
* The Uart and SPi clocks are set.
****************************************************************************************
*/
void periph_init(void) // set i2c, spi, uart, uart2 serial clks
{
// Power up peripherals' power domain
SetBits16(PMU_CTRL_REG, PERIPH_SLEEP, 0);
while (!(GetWord16(SYS_STAT_REG) & PER_IS_UP)) ;
// TODO: Application specific - Modify accordingly!
// Example: Activate UART and SPI.
// Initialize UART component
#ifdef PROGRAM_ENABLE_UART
SetBits16(CLK_PER_REG, UART1_ENABLE, 1); // enable clock - always @16MHz
// baudr=9-> 115k2
// mode=3-> no parity, 1 stop bit 8 data length
#ifdef UART_MEGABIT
uart_init(UART_BAUDRATE_1M, 3);
#else
uart_init(UART_BAUDRATE_115K2, 3);
#endif // UART_MEGABIT
//NVIC_SetPriority(UART_IRQn, 1);
#endif // PROGRAM_ENABLE_UART
#if 0
//Example: Do something with the timer if need be...
SetWord16(TIMER0_CTRL_REG, 0);
SetWord16(TIMER0_RELOAD_M_REG, 0);
SetWord16(TIMER0_RELOAD_N_REG, 0);
SetWord16(TIMER0_ON_REG, 0);
#endif
//rom patch
patch_func();
//Init pads
set_pad_functions();
#if (BLE_APP_PRESENT)
#if BLE_BATTERY_SERVER
app_batt_port_reinit();
#endif //BLE_BATTERY_SERVER
#endif //BLE_APP_PRESENT
// Enable the pads
SetBits16(SYS_CTRL_REG, PAD_LATCH_EN, 1);
}
/**
****************************************************************************************
* @brief Enable pad's and peripheral clocks assuming that peripherals' power domain is down.
*
*
* @return void
****************************************************************************************
*/
void periph_init(void)
{
// Power up peripherals' power domain
SetBits16(PMU_CTRL_REG, PERIPH_SLEEP, 0);
while (!(GetWord16(SYS_STAT_REG) & PER_IS_UP)) ;
SetBits16(CLK_16M_REG, XTAL16_BIAS_SH_DISABLE, 1);
// Initialize UART component
#ifdef PROGRAM_ENABLE_UART
if (GetBits16(CLK_CTRL_REG, RUNNING_AT_XTAL16M)) {
SetBits16(CLK_PER_REG, UART1_ENABLE, 1); // enable clock - always @16MHz
// mode=3-> no parity, 1 stop bit 8 data length
#ifdef UART_MEGABIT
uart_init(UART_BAUDRATE_1M, 3);
#else
uart_init(UART_BAUDRATE_115K2, 3);
#endif // UART_MEGABIT
}
#endif // PROGRAM_ENABLE_UART
//FPGA
#ifdef FPGA_USED
SetBits16(CLK_PER_REG, SPI_ENABLE, 1); // enable clock
SetBits16(CLK_PER_REG, SPI_DIV, 1); // set divider to 1
SetBits16(CLK_PER_REG, WAKEUPCT_ENABLE, 1); // enable clock of Wakeup Controller
#endif
//rom patch
patch_func();
//Init pads
set_pad_functions();
#ifndef FPGA_USED
// SetBits16(CLK_PER_REG, WAKEUPCT_ENABLE, 1); // enable clock of Wakeup Controller
#endif
//SetWord16(P01_PADPWR_CTRL_REG,0xFF);
// Enable the pads
SetBits16(SYS_CTRL_REG, PAD_LATCH_EN, 1);
}
/**
****************************************************************************************
* @brief Enable pad's and peripheral clocks assuming that peripherals' power domain is down.
*
* The Uart and SPi clocks are set.
****************************************************************************************
*/
void periph_init(void) // set i2c, spi, uart, uart2 serial clks
{
// Power up peripherals' power domain
SetBits16(PMU_CTRL_REG, PERIPH_SLEEP, 0);
while (!(GetWord16(SYS_STAT_REG) & PER_IS_UP)) ;
#if ES4_CODE
SetBits16(CLK_16M_REG,XTAL16_BIAS_SH_DISABLE, 1);
#endif
spi_hci_slave_init();
//rom patch
patch_func();
//Init pads
set_pad_functions();
// Enable the pads
SetBits16(SYS_CTRL_REG, PAD_LATCH_EN, 1);
}
/**
****************************************************************************************
* @brief Enable pad's and peripheral clocks assuming that peripherals' power domain is down. The Uart and SPi clocks are set.
*
* @return void
****************************************************************************************
*/
void periph_init(void)
{
// Power up peripherals' power domain
SetBits16(PMU_CTRL_REG, PERIPH_SLEEP, 0);
while (!(GetWord16(SYS_STAT_REG) & PER_IS_UP)) ;
//rom patch
patch_func();
//Init pads
set_pad_functions();
SetBits16(CLK_PER_REG, UART1_ENABLE, 1); // enable clock - always @16MHz
// baudr=9-> 115k2
// mode=3-> no parity, 1 stop bit 8 data length
uart_sps_init(UART_SPS_BAUDRATE, 3); //exact baud rate defined in uart.h
// Enable the pads
SetBits16(SYS_CTRL_REG, PAD_LATCH_EN, 1);
#if (EXT_SLEEP_ENABLED)
app_scheduler_reinit();
#endif //EXT_SLEEP_ENABLED
#if ((UART_HW_FLOW_ENABLED) && !defined(GPIO_DRV_IRQ_HANDLING_DISABLED))
GPIO_RegisterCallback(GPIO0_IRQn, gpio0_callback);
if(GPIO_GetPinStatus(UART1_CTS_PORT,UART1_CTS_PIN)==FALSE)
{
GPIO_EnableIRQ(UART1_CTS_PORT, UART1_CTS_PIN, GPIO0_IRQn, 0, 1, 0);
}
else if(GPIO_GetPinStatus(UART1_CTS_PORT,UART1_CTS_PIN)==TRUE)
{
GPIO_EnableIRQ(UART1_CTS_PORT, UART1_CTS_PIN, GPIO0_IRQn, 1, 0, 0);
}
#endif //((UART_HW_FLOW_ENABLED) && !defined(GPIO_DRV_IRQ_HANDLING_DISABLED))
}
/**
****************************************************************************************
* @brief Enable pad's and peripheral clocks assuming that peripherals' power domain is down. The Uart and SPi clocks are set.
*
* @return void
****************************************************************************************
*/
void periph_init(void)
{
// Power up peripherals' power domain
SetBits16(PMU_CTRL_REG, PERIPH_SLEEP, 0);
while (!(GetWord16(SYS_STAT_REG) & PER_IS_UP)) ;
#if ES4_CODE
SetBits16(CLK_16M_REG,XTAL16_BIAS_SH_DISABLE, 1);
#endif
#if BLE_INTEGRATED_HOST_GTL
// Initialize UART component
SetBits16(CLK_PER_REG, UART1_ENABLE, 1); // enable clock - always @16MHz
// baudr=9-> 115k2
// mode=3-> no parity, 1 stop bit 8 data length
uart_init(UART_BAUDRATE_115K2, 3);
#endif
//rom patch
patch_func();
//Init pads
set_pad_functions();
#if (BLE_APP_PRESENT)
/*
* (Re)Initialize peripherals
i.e.
uart_init(UART_BAUDRATE_115K2, 3);
*/
#endif
// Enable the pads
SetBits16(SYS_CTRL_REG, PAD_LATCH_EN, 1);
}
/**
****************************************************************************************
* @brief Enable pad's and peripheral clocks assuming that peripherals' power domain is down.
*
* The Uart and SPi clocks are set.
****************************************************************************************
*/
void periph_init(void) // set i2c, spi, uart, uart2 serial clks
{
// Power up peripherals' power domain
SetBits16(PMU_CTRL_REG, PERIPH_SLEEP, 0);
while (!(GetWord16(SYS_STAT_REG) & PER_IS_UP)) ;
#if ES4_CODE
SetBits16(CLK_16M_REG,XTAL16_BIAS_SH_DISABLE, 1);
#endif
// TODO: Application specific - Modify accordingly!
// Example: Activate UART and SPI.
// Initialize UART component
#ifdef PROGRAM_ENABLE_UART
SetBits16(CLK_PER_REG, UART1_ENABLE, 1); // enable clock - always @16MHz
// baudr=9-> 115k2
// mode=3-> no parity, 1 stop bit 8 data length
#ifdef UART_MEGABIT
uart_init(UART_BAUDRATE_1M, 3);
#else
uart_init(UART_BAUDRATE_115K2, 3);
#endif // UART_MEGABIT
//NVIC_SetPriority(UART_IRQn, 1); // remove if the bug in uart.c is fixed in ES4(b)!
#endif // PROGRAM_ENABLE_UART
//FPGA
#ifdef FPGA_USED
SetBits16(CLK_PER_REG, SPI_ENABLE, 1); // enable clock
SetBits16(CLK_PER_REG, SPI_DIV, 1); // set divider to 1
#endif
#if BLE_ACCEL
SetBits16(CLK_PER_REG, SPI_ENABLE, 1); // enable clock
SetBits16(CLK_PER_REG, SPI_DIV, 1); // set divider to 1
SetBits16(CLK_PER_REG, WAKEUPCT_ENABLE, 1); // enable clock of Wakeup Controller
#endif
#if 0
//Example: Do something with the timer if need be...
SetWord16(TIMER0_CTRL_REG, 0);
SetWord16(TIMER0_RELOAD_M_REG, 0);
SetWord16(TIMER0_RELOAD_N_REG, 0);
SetWord16(TIMER0_ON_REG, 0);
#endif
//rom patch
patch_func();
//Init pads
set_pad_functions();
#ifndef FPGA_USED
#if (BLE_APP_PRESENT)
#if BLE_HID_DEVICE
SetBits16(CLK_PER_REG, WAKEUPCT_ENABLE, 1); // enable clock of Wakeup Controller
// if (app_env.app_flags & KBD_START_SCAN) // reinit kbd only if needed
if ( !(app_env.app_flags & KBD_START_SCAN) && !(app_env.app_flags & KBD_SCANNING) )
app_kbd_reinit_matrix();
#endif // BLE_HID_DEVICE
#if BLE_PROX_REPORTER
app_proxr_port_reinit();
#elif BLE_FINDME_LOCATOR
app_button_enable();
#endif //BLE_PROX_REPORTER
#if BLE_SPOTA_RECEIVER
app_spotar_init();
#endif // BLE_SPOTA_RECEIVER
#if BLE_STREAMDATA_DEVICE
stream_start_button_init();
#endif //BLE_STREAMDATA_DEVICE
#if BLE_BATTERY_SERVER
app_batt_port_reinit();
#endif //BLE_BATTERY_SERVER
#endif
#endif
// Enable the pads
SetBits16(SYS_CTRL_REG, PAD_LATCH_EN, 1);
}
