/*
* Routine: board_eth_init
* Description: initialize module and base-board Ethernet chips
*/
int board_eth_init(bd_t *bis)
{
int rc = 0, rc1 = 0;
setup_net_chip_gmpc();
reset_net_chip();
rc1 = handle_mac_address();
if (rc1)
printf("No MAC address found! ");
rc1 = smc911x_initialize(0, CM_T3X_SMC911X_BASE);
if (rc1 > 0)
rc++;
rc1 = smc911x_initialize(1, SB_T35_SMC911X_BASE);
if (rc1 > 0)
rc++;
return rc;
}
int board_eth_init(bd_t *bis)
{
davinci_emac_initialize();
/* init cs for extern lan */
enable_gpmc_cs_config(gpmc_smc911, &gpmc_cfg->cs[5],
CONFIG_SMC911X_BASE, GPMC_SIZE_16M);
if (smc911x_initialize(0, CONFIG_SMC911X_BASE) <= 0)
printf("\nError initializing SMC911x controlleri\n");
return 0;
}
int board_eth_init(bd_t *bis)
{
int rc = -ENODEV;
weim_smc911x_iomux();
weim_cs1_settings();
#ifdef CONFIG_SMC911X
rc = smc911x_initialize(0, CONFIG_SMC911X_BASE);
#endif
return rc;
}
/*
* Routine: board_eth_init
* Description: initialize module and base-board Ethernet chips
*/
int board_eth_init(bd_t *bis)
{
int rc = 0, rc1 = 0;
#ifdef CONFIG_SMC911X
setup_net_chip_gmpc();
reset_net_chip();
rc1 = handle_mac_address();
if (rc1)
printf("CM-T3x: No MAC address found\n");
rc1 = smc911x_initialize(0, CM_T3X_SMC911X_BASE);
if (rc1 > 0)
rc++;
rc1 = smc911x_initialize(1, SB_T35_SMC911X_BASE);
if (rc1 > 0)
rc++;
#endif
return rc;
}
int board_eth_init(bd_t *bis)
{
#ifdef CONFIG_SMC911X
u32 smc_bw_conf, smc_bc_conf;
struct fdt_sromc config;
fdt_addr_t base_addr;
int node;
node = decode_sromc(gd->fdt_blob, &config);
if (node < 0) {
debug("%s: Could not find sromc configuration\n", __func__);
return 0;
}
node = fdtdec_next_compatible(gd->fdt_blob, node, COMPAT_SMSC_LAN9215);
if (node < 0) {
debug("%s: Could not find lan9215 configuration\n", __func__);
return 0;
}
/* We now have a node, so any problems from now on are errors */
base_addr = fdtdec_get_addr(gd->fdt_blob, node, "reg");
if (base_addr == FDT_ADDR_T_NONE) {
debug("%s: Could not find lan9215 address\n", __func__);
return -1;
}
/* Ethernet needs data bus width of 16 bits */
if (config.width != 2) {
debug("%s: Unsupported bus width %d\n", __func__,
config.width);
return -1;
}
smc_bw_conf = SROMC_DATA16_WIDTH(config.bank)
| SROMC_BYTE_ENABLE(config.bank);
smc_bc_conf = SROMC_BC_TACS(config.timing[FDT_SROM_TACS]) |
SROMC_BC_TCOS(config.timing[FDT_SROM_TCOS]) |
SROMC_BC_TACC(config.timing[FDT_SROM_TACC]) |
SROMC_BC_TCOH(config.timing[FDT_SROM_TCOH]) |
SROMC_BC_TAH(config.timing[FDT_SROM_TAH]) |
SROMC_BC_TACP(config.timing[FDT_SROM_TACP]) |
SROMC_BC_PMC(config.timing[FDT_SROM_PMC]);
/* Select and configure the SROMC bank */
exynos_pinmux_config(PERIPH_ID_SROMC, config.bank);
s5p_config_sromc(config.bank, smc_bw_conf, smc_bc_conf);
return smc911x_initialize(0, base_addr);
#endif
return 0;
}
int board_eth_init(bd_t *bis)
{
#ifdef CONFIG_SMC911X
u32 smc_bw_conf, smc_bc_conf;
struct fdt_sromc config;
fdt_addr_t base_addr;
/* Non-FDT configuration - bank number and timing parameters*/
config.bank = CONFIG_ENV_SROM_BANK;
config.width = 2;
config.timing[FDT_SROM_TACS] = 0x01;
config.timing[FDT_SROM_TCOS] = 0x01;
config.timing[FDT_SROM_TACC] = 0x06;
config.timing[FDT_SROM_TCOH] = 0x01;
config.timing[FDT_SROM_TAH] = 0x0C;
config.timing[FDT_SROM_TACP] = 0x09;
config.timing[FDT_SROM_PMC] = 0x01;
base_addr = CONFIG_SMC911X_BASE;
/* Ethernet needs data bus width of 16 bits */
if (config.width != 2) {
debug("%s: Unsupported bus width %d\n", __func__,
config.width);
return -1;
}
smc_bw_conf = SROMC_DATA16_WIDTH(config.bank)
| SROMC_BYTE_ENABLE(config.bank);
smc_bc_conf = SROMC_BC_TACS(config.timing[FDT_SROM_TACS]) |\
SROMC_BC_TCOS(config.timing[FDT_SROM_TCOS]) |\
SROMC_BC_TACC(config.timing[FDT_SROM_TACC]) |\
SROMC_BC_TCOH(config.timing[FDT_SROM_TCOH]) |\
SROMC_BC_TAH(config.timing[FDT_SROM_TAH]) |\
SROMC_BC_TACP(config.timing[FDT_SROM_TACP]) |\
SROMC_BC_PMC(config.timing[FDT_SROM_PMC]);
/* Select and configure the SROMC bank */
exynos_pinmux_config(PERIPH_ID_SROMC, config.bank);
s5p_config_sromc(config.bank, smc_bw_conf, smc_bc_conf);
return smc911x_initialize(0, base_addr);
#endif
return 0;
}
int cl_omap3_smc911x_init(int id, int cs, u32 base_addr,
int (*reset)(int), int rst_gpio)
{
int ret;
cl_omap3_smc911x_setup_net_chip_gmpc(cs, base_addr);
if (reset)
reset(rst_gpio);
else
cl_omap3_smc911x_reset_net_chip(rst_gpio);
ret = smc911x_initialize(id, base_addr);
if (ret > 0)
return ret;
printf("Failed initializing SMC911x! ");
return 0;
}
int board_eth_init(bd_t *bis)
{
int rc = 0;
#ifdef CONFIG_SMC911X
#define STR_ENV_ETHADDR "ethaddr"
struct eth_device *dev;
uchar eth_addr[6];
rc = smc911x_initialize(0, CONFIG_SMC911X_BASE);
if (!eth_getenv_enetaddr(STR_ENV_ETHADDR, eth_addr)) {
dev = eth_get_dev_by_index(0);
if (dev) {
eth_setenv_enetaddr(STR_ENV_ETHADDR, dev->enetaddr);
} else {
printf("omap3evm: Couldn't get eth device\n");
rc = -1;
}
}
#endif
return rc;
}
int board_eth_init(bd_t *bis)
{
int rc = 0;
rc = smc911x_initialize(0, CONFIG_SMC911X_BASE);
return rc;
}
int board_eth_init(bd_t *bis)
{
return smc911x_initialize(0, CONFIG_SMC911X_BASE);
}
int board_eth_init(bd_t *bis)
{
/* return ok if at least 1 eth device works */
return bfin_EMAC_initialize(bis) &
smc911x_initialize(0, CONFIG_SMC911X_BASE);
}