int __init da8xx_register_uio_pruss(void)
{
da8xx_uio_pruss_pdata.sram_pool = sram_get_gen_pool();
return platform_device_register(&da8xx_uio_pruss_dev);
}
static __init void da850_evm_init(void)
{
int ret;
ret = da850_register_gpio();
if (ret)
pr_warn("%s: GPIO init failed: %d\n", __func__, ret);
ret = pmic_tps65070_init();
if (ret)
pr_warn("%s: TPS65070 PMIC init failed: %d\n", __func__, ret);
ret = da850_register_edma(da850_edma_rsv);
if (ret)
pr_warn("%s: EDMA registration failed: %d\n", __func__, ret);
ret = davinci_cfg_reg_list(da850_i2c0_pins);
if (ret)
pr_warn("%s: I2C0 mux setup failed: %d\n", __func__, ret);
ret = da8xx_register_i2c(0, &da850_evm_i2c_0_pdata);
if (ret)
pr_warn("%s: I2C0 registration failed: %d\n", __func__, ret);
ret = da8xx_register_watchdog();
if (ret)
pr_warn("%s: watchdog registration failed: %d\n",
__func__, ret);
if (HAS_MMC) {
ret = davinci_cfg_reg_list(da850_evm_mmcsd0_pins);
if (ret)
pr_warn("%s: MMCSD0 mux setup failed: %d\n",
__func__, ret);
ret = gpio_request(DA850_MMCSD_CD_PIN, "MMC CD\n");
if (ret)
pr_warn("%s: can not open GPIO %d\n",
__func__, DA850_MMCSD_CD_PIN);
gpio_direction_input(DA850_MMCSD_CD_PIN);
ret = gpio_request(DA850_MMCSD_WP_PIN, "MMC WP\n");
if (ret)
pr_warn("%s: can not open GPIO %d\n",
__func__, DA850_MMCSD_WP_PIN);
gpio_direction_input(DA850_MMCSD_WP_PIN);
ret = da8xx_register_mmcsd0(&da850_mmc_config);
if (ret)
pr_warn("%s: MMCSD0 registration failed: %d\n",
__func__, ret);
ret = da850_wl12xx_init();
if (ret)
pr_warn("%s: WL12xx initialization failed: %d\n",
__func__, ret);
}
davinci_serial_init(da8xx_serial_device);
i2c_register_board_info(1, da850_evm_i2c_devices,
ARRAY_SIZE(da850_evm_i2c_devices));
/*
* shut down uart 0 and 1; they are not used on the board and
* accessing them causes endless "too much work in irq53" messages
* with arago fs
*/
__raw_writel(0, IO_ADDRESS(DA8XX_UART1_BASE) + 0x30);
__raw_writel(0, IO_ADDRESS(DA8XX_UART0_BASE) + 0x30);
ret = davinci_cfg_reg_list(da850_evm_mcasp_pins);
if (ret)
pr_warn("%s: McASP mux setup failed: %d\n", __func__, ret);
da850_evm_snd_data.sram_pool = sram_get_gen_pool();
da8xx_register_mcasp(0, &da850_evm_snd_data);
ret = davinci_cfg_reg_list(da850_lcdcntl_pins);
if (ret)
pr_warn("%s: LCDC mux setup failed: %d\n", __func__, ret);
ret = da8xx_register_uio_pruss();
if (ret)
pr_warn("da850_evm_init: pruss initialization failed: %d\n",
ret);
/* Handle board specific muxing for LCD here */
ret = davinci_cfg_reg_list(da850_evm_lcdc_pins);
if (ret)
pr_warn("%s: EVM specific LCD mux setup failed: %d\n",
__func__, ret);
ret = da850_lcd_hw_init();
if (ret)
pr_warn("%s: LCD initialization failed: %d\n", __func__, ret);
sharp_lk043t1dg01_pdata.panel_power_ctrl = da850_panel_power_ctrl,
ret = da8xx_register_lcdc(&sharp_lk043t1dg01_pdata);
if (ret)
pr_warn("%s: LCDC registration failed: %d\n", __func__, ret);
ret = da8xx_register_rtc();
if (ret)
pr_warn("%s: RTC setup failed: %d\n", __func__, ret);
ret = da850_evm_init_cpufreq();
if (ret)
pr_warn("%s: cpufreq registration failed: %d\n", __func__, ret);
ret = da8xx_register_cpuidle();
if (ret)
pr_warn("%s: cpuidle registration failed: %d\n", __func__, ret);
ret = da850_register_pm(&da850_pm_device);
if (ret)
pr_warn("%s: suspend registration failed: %d\n", __func__, ret);
da850_vpif_init();
ret = spi_register_board_info(da850evm_spi_info,
ARRAY_SIZE(da850evm_spi_info));
if (ret)
pr_warn("%s: spi info registration failed: %d\n", __func__,
ret);
ret = da8xx_register_spi_bus(1, ARRAY_SIZE(da850evm_spi_info));
if (ret)
pr_warn("%s: SPI 1 registration failed: %d\n", __func__, ret);
ret = da850_register_sata(DA850EVM_SATA_REFCLKPN_RATE);
if (ret)
pr_warn("%s: SATA registration failed: %d\n", __func__, ret);
da850_evm_setup_mac_addr();
ret = da8xx_register_rproc();
if (ret)
pr_warn("%s: dsp/rproc registration failed: %d\n",
__func__, ret);
}
