void bfmsys85_state::machine_start()
{
int i;
for ( i = 0; i < 4; i++ )
{
stepper_config(machine(), i, &starpoint_interface_48step);
}
}
static MACHINE_START( bfm_sys85 )
{
int i;
for ( i = 0; i < 4; i++ )
{
stepper_config(machine, i, &starpoint_interface_48step);
}
ROC10937_init(0,MSC1937,1);//?
}
INPUT_PORTS_END
void maygay1b_state::machine_start()
{
int i;
// setup 8 mechanical meters ////////////////////////////////////////////
MechMtr_config(machine(),8);
// setup 6 default 96 half step reels ///////////////////////////////////
for ( i = 0; i < 6; i++ )
{
stepper_config(machine(), i, &starpoint_interface_48step);
}
}
/*
* Setup all sub sys of unicorn
*/
static int unicorn_setup()
{
int ret = 0;
if (bbp_board_type == BOARD_BBP1) {
printf("Board is FastBot BBP 1\n");
ret = analog_config(analog_config_bbp1, NR_ITEMS(analog_config_bbp1));
if (ret < 0) {
printf("analog_config failed\n");
goto out;
}
ret = temp_config(temp_config_data_bbp1, NR_ITEMS(temp_config_data_bbp1));
if (ret < 0) {
printf("temp_config failed\n");
goto out;
}
ret = pwm_config(pwm_config_bbp1, NR_ITEMS(pwm_config_bbp1));
if (ret < 0) {
printf("pwm_config failed\n");
goto out;
}
ret = fan_config(fan_config_bbp1, NR_ITEMS(fan_config_bbp1));
if (ret < 0) {
printf("fan_config failed\n");
goto out;
}
ret = heater_config(heater_config_data_bbp, NR_ITEMS(heater_config_data_bbp));
if (ret < 0) {
printf("heater_config failed\n");
goto out;
}
ret = stepper_config(stepper_config_bbp1, NR_ITEMS(stepper_config_bbp1));
if (ret < 0) {
printf("stepper_config failed\n");
goto out;
}
} else if (bbp_board_type == BOARD_BBP1S) {
printf("Board is FastBot BBP 1s\n");
ret = analog_config(analog_config_bbp1s, NR_ITEMS(analog_config_bbp1s));
if (ret < 0) {
printf("analog_config failed\n");
goto out;
}
ret = temp_config(temp_config_data_bbp1s, NR_ITEMS(temp_config_data_bbp1s));
if (ret < 0) {
printf("temp_config failed\n");
goto out;
}
ret = pwm_config(pwm_config_bbp1s, NR_ITEMS(pwm_config_bbp1s));
if (ret < 0) {
printf("pwm_config failed\n");
goto out;
}
ret = fan_config(fan_config_bbp1s, NR_ITEMS(fan_config_bbp1s));
if (ret < 0) {
printf("fan_config failed\n");
goto out;
}
ret = heater_config(heater_config_data_bbp1s, NR_ITEMS(heater_config_data_bbp1s));
if (ret < 0) {
printf("heater_config failed\n");
goto out;
}
#ifdef SERVO
if (bbp_board_type == BOARD_BBP1S) {
ret = servo_config(servo_config_data, NR_ITEMS(servo_config_data));
if (ret < 0) {
printf("servo_config failed\n");
goto out;
}
}
#endif
ret = stepper_config(stepper_config_bbp1s, NR_ITEMS(stepper_config_bbp1s));
if (ret < 0) {
printf("stepper_config failed\n");
goto out;
}
} else {
printf("Not supported board!\n");
}
out:
return ret;
}
