void restorerf230state()
{
if (tat_set_trx_state( RX_ON )==TAT_SUCCESS)
{
}
}
/**
* call it after wake up from stop mode
*/
void leave_node_stop(void) {
// restore clock
SYSCLKConfig_STOP();
untesting();
// restore components
unset_pin();
// RF
tat_leave_sleep_mode();
// flash
//flash_on();
// set RF to RX state
while((tat_set_trx_state(RX_AACK_ON)!=TAT_SUCCESS)) delay_ms(1);
#ifdef MY_DEBUG
hal_set_net_led();
hal_set_data_led();
#endif
}
/** @brief IRIS: This function is used to initialize the TRX.
*
* @return true if the TRX was successfully configured.
* @return false if the TRX was not configured properly.
*/
inline bool2 trx_init( void ){
static bool2 status;
if (tat_init( ) != TAT_SUCCESS) {
//Leds_yellowToggle(); //Debug--Redtoggle Upon
status = false;
} else if (tat_set_operating_channel( 21 ) != TAT_SUCCESS) {
status = false;
} else if (tat_set_clock_speed( true, CLKM_DISABLED ) != TAT_SUCCESS) {
status = false;
} else{
tat_use_auto_tx_crc( true ); //Automatic CRC must be enabled.
status = true;
} // end: if (tat_init( ) != TAT_SUCCESS) ...
rf230radiom_currentDSN = 0;
if (tat_set_trx_state( RX_ON )==TAT_SUCCESS) {}
else
{}
return status;
}
result_t rf230radio_Send_send(Radio_MsgPtr pMsg)
{
unsigned char result;
// format the 802.15.4 packet
#ifdef VER_DEBUG
temp = pMsg;
#endif
pMsg->fcflo=0x08;
pMsg->fcfhi=0x01;
pMsg->dsn = rf230radiom_currentDSN ++; //seq ++
pMsg->destpan=BCAST_ADDRESS;
//pMsg->addr==BCAST_ADDRESS;
pMsg->addr = toLSB16 (pMsg->addr);
// pMsg->port=0x3377; //specify the port number to 0x0077
if ( pMsg->dsn==255) pMsg->dsn=0;
pMsg->time=0;
pMsg->length=pMsg->length+MSG_HEADER_SIZE; //Set the length like in cc2420radiom.c, check if bug happens
// just send out payload data first, add 15.4 header later
/*Ensure that it is possible to enter PLL_ON*/
// tat_reset_trx();
//tat_reset_state_machine();
if (tat_set_trx_state( PLL_ON ) == TAT_SUCCESS) {
result= tat_send_data((pMsg->length+2), ((uint8_t*) pMsg)+1); //Note: Include MSG_FOOTER_SIZE
if (result == TAT_SUCCESS)
{ result=SUCCESS;
if( tat_get_trx_state( )!=PLL_ON) {
if(tat_set_trx_state( PLL_ON )!=TAT_SUCCESS)
{
result= FAIL;
return result;
}
}
else {
}
//delay_us(1000);
// for (i=0;i++;i<100000)
// {
// asm volatile("nop"::);
// }
// Option-Go to RX_ON after Send-Important!
if (tat_set_trx_state( RX_ON )==TAT_SUCCESS)
printfstr ("\n after send go to RX_ON sucessfully ");
else {
result=FAIL;
}
}
else {
if (tat_set_trx_state( RX_ON )==TAT_SUCCESS)
printfstr ("\n after send go to RX_ON sucessfully ");
else {
result=FAIL;
}
result=FAIL;
}
}
else {
result=FAIL;
}
return result;
}
