void store_new_wakeup(void)
{
uint8_t idx;
IRMP_DATA wakeup_IRData;
toggle_LED();
/* 5 seconds to press button on remote */
delay_ms(5000);
if (irmp_get_data(&wakeup_IRData)) {
wakeup_IRData.flags = 0;
idx = (MACRO_DEPTH + 1) * SIZEOF_IR/2 * MACRO_SLOTS;
/* store received wakeup IRData in first wakeup slot */
eeprom_store(idx, (uint8_t *) &wakeup_IRData);
toggle_LED();
}
}
/**
* \brief SysTick Interrupt handler.
*/
void SysTick_Handler( void )
{
ul_tickcount++ ;
// Toggle LEDs every second (ie 1000ms)
if ( ul_tickcount % 1000 == 0 )
{
toggle_LED() ;
}
}
/**
* \brief PIOA interrupt handler.
*
*/
void PIOA_Handler( void )
{
uint32_t ul_status ;
/* Read PIO controller status */
ul_status = SW0_PIO->PIO_ISR ;
ul_status &= SW0_PIO->PIO_IMR ;
/* Check pending events */
if ( (ul_status & SW0_PIN) != 0 )
{
toggle_LED() ;
}
}
// PE0, PB0, or PA2 connected to positive logic momentary switch using 10k ohm pull down resistor
// PE1, PB1, or PA3 connected to positive logic LED through 470 ohm current limiting resistor
// To avoid damaging your hardware, ensure that your circuits match the schematic
// shown in Lab8_artist.sch (PCB Artist schematic file) or
// Lab8_artist.pdf (compatible with many various readers like Adobe Acrobat).
int main(void){ unsigned long volatile Input;
//**********************************************************************
// The following version tests input on PE0 and output on PE1
//**********************************************************************
TExaS_Init(SW_PIN_PE0, LED_PIN_PE1); // activate grader and set system clock to 80 MHz
PORTE_Init();
EnableInterrupts(); // enable interrupts for the grader
GPIO_PORTE_DATA_R |= 0x02; // turn LED on
while(1){
Delayms(100); // delay of 100ms
Input = GPIO_PORTE_DATA_R & 0x01;
if (Input == 0x01) { // if switch (PE1) is pressed
toggle_LED(); // toggle LED once
}
else{
GPIO_PORTE_DATA_R = 0x02;
}
}
}
int main(void)
{
uint8_t buf[HID_OUT_BUFFER_SIZE-1], RepeatCounter = 0;
IRMP_DATA myIRData;
int8_t ret;
/* first wakeup slot empty? */
uint8_t learn_wakeup = eeprom_restore(buf, (MACRO_DEPTH + 1) * SIZEOF_IR/2 * MACRO_SLOTS);
USB_HID_Init();
LED_Switch_init();
IRMP_Init();
irsnd_init();
FLASH_Unlock();
EE_Init();
Systick_Init();
while (1) {
if (!AlarmValue)
Wakeup();
wakeup_reset();
/* test if USB is connected to PC and command is received */
if (USB_HID_GetStatus() == USB_HID_CONNECTED && USB_HID_ReceiveData(buf) == RX_READY && buf[0] == STAT_CMD) {
switch ((enum access) buf[1]) {
case ACC_GET:
ret = get_handler(buf);
break;
case ACC_SET:
ret = set_handler(buf);
break;
case ACC_RESET:
ret = reset_handler(buf);
break;
default:
ret = -1;
}
if (ret == -1) {
buf[0] = STAT_FAILURE;
ret = 3;
} else {
buf[0] = STAT_SUCCESS;
}
/* send configuration data */
USB_HID_SendData(REPORT_ID_CONFIG, buf, ret);
toggle_LED();
}
/* poll IR-data */
if (irmp_get_data(&myIRData)) {
if (learn_wakeup) {
/* store received wakeup IRData in first wakeup slot */
eeprom_store((MACRO_DEPTH + 1) * SIZEOF_IR/2 * MACRO_SLOTS, (uint8_t *) &myIRData);
learn_wakeup = 0;
}
if (!(myIRData.flags)) {
RepeatCounter = 0;
} else {
RepeatCounter++;
}
if (RepeatCounter == 0 || RepeatCounter >= MIN_REPEATS) {
toggle_LED();
/* if macros are sent already, while the trigger IR data are still repeated,
* the receiving device may crash */
check_macros(&myIRData);
check_wakeups(&myIRData);
}
/* send IR-data */
memcpy(buf, &myIRData, sizeof(myIRData));
USB_HID_SendData(REPORT_ID_IR, buf, sizeof(myIRData));
}
}
}
