static int __init osk_tps_init(void)
{
if (!machine_is_omap_osk())
return 0;
/* Let LED1 (D9) blink */
tps65010_set_led(LED1, BLINK);
/* Disable LED 2 (D2) */
tps65010_set_led(LED2, OFF);
/* Set GPIO 1 HIGH to disable VBUS power supply;
* OHCI driver powers it up/down as needed.
*/
tps65010_set_gpio_out_value(GPIO1, HIGH);
/* Set GPIO 2 low to turn on LED D3 */
tps65010_set_gpio_out_value(GPIO2, HIGH);
/* Set GPIO 3 low to take ethernet out of reset */
tps65010_set_gpio_out_value(GPIO3, LOW);
/* gpio4 for VDD_DSP */
/* FIXME send power to DSP iff it's configured */
/* Enable LOW_PWR */
tps65010_set_low_pwr(ON);
/* Switch VLDO2 to 3.0V for AIC23 */
tps65010_config_vregs1(TPS_LDO2_ENABLE | TPS_VLDO2_3_0V
| TPS_LDO1_ENABLE);
return 0;
}
static void h3_panel_disable(struct lcd_panel *panel)
{
int r = 0;
/* GPIO1 and GPIO2 of TPS65010 send LCD_ENBKL and LCD_ENVDD signals */
r = tps65010_set_gpio_out_value(GPIO1, LOW);
if (!r)
tps65010_set_gpio_out_value(GPIO2, LOW);
if (r)
pr_err(MODULE_NAME ": Unable to turn off LCD panel\n");
}
static int h3_panel_enable(struct lcd_panel *panel)
{
int r = 0;
/* GPIO1 and GPIO2 of TPS65010 send LCD_ENBKL and LCD_ENVDD signals */
r = tps65010_set_gpio_out_value(GPIO1, HIGH);
if (!r)
r = tps65010_set_gpio_out_value(GPIO2, HIGH);
if (r)
pr_err(MODULE_NAME ": Unable to turn on LCD panel\n");
return r;
}
static void tps_work(void *unused)
{
for (;;) {
u8 leds;
local_irq_disable();
leds = tps_leds_change;
tps_leds_change = 0;
local_irq_enable();
if (!leds)
break;
/* careful: the set_led() value is on/off/blink */
if (leds & GREEN_LED)
tps65010_set_led(LED1, !!(hw_led_state & GREEN_LED));
if (leds & AMBER_LED)
tps65010_set_led(LED2, !!(hw_led_state & AMBER_LED));
/* the gpio led doesn't have that issue */
if (leds & RED_LED)
tps65010_set_gpio_out_value(GPIO2,
!(hw_led_state & RED_LED));
}
}
/*
* Board specific gang-switched transceiver power on/off.
* NOTE: OSK supplies power from DC, not battery.
*/
static int omap_ohci_transceiver_power(int on)
{
if (on) {
if (machine_is_omap_innovator() && cpu_is_omap1510())
fpga_write(fpga_read(INNOVATOR_FPGA_CAM_USB_CONTROL)
| ((1 << 5/*usb1*/) | (1 << 3/*usb2*/)),
INNOVATOR_FPGA_CAM_USB_CONTROL);
else if (machine_is_omap_osk())
tps65010_set_gpio_out_value(GPIO1, LOW);
} else {
if (machine_is_omap_innovator() && cpu_is_omap1510())
fpga_write(fpga_read(INNOVATOR_FPGA_CAM_USB_CONTROL)
& ~((1 << 5/*usb1*/) | (1 << 3/*usb2*/)),
INNOVATOR_FPGA_CAM_USB_CONTROL);
else if (machine_is_omap_osk())
tps65010_set_gpio_out_value(GPIO1, HIGH);
}
return 0;
}
static int osk_tps_setup(struct i2c_client *client, void *context)
{
if (!IS_BUILTIN(CONFIG_TPS65010))
return -ENOSYS;
/* Set GPIO 1 HIGH to disable VBUS power supply;
* OHCI driver powers it up/down as needed.
*/
gpio_request(OSK_TPS_GPIO_USB_PWR_EN, "n_vbus_en");
gpio_direction_output(OSK_TPS_GPIO_USB_PWR_EN, 1);
/* Set GPIO 2 high so LED D3 is off by default */
tps65010_set_gpio_out_value(GPIO2, HIGH);
/* Set GPIO 3 low to take ethernet out of reset */
gpio_request(OSK_TPS_GPIO_LAN_RESET, "smc_reset");
gpio_direction_output(OSK_TPS_GPIO_LAN_RESET, 0);
/* GPIO4 is VDD_DSP */
gpio_request(OSK_TPS_GPIO_DSP_PWR_EN, "dsp_power");
gpio_direction_output(OSK_TPS_GPIO_DSP_PWR_EN, 1);
/* REVISIT if DSP support isn't configured, power it off ... */
/* Let LED1 (D9) blink; leds-gpio may override it */
tps65010_set_led(LED1, BLINK);
/* Set LED2 off by default */
tps65010_set_led(LED2, OFF);
/* Enable LOW_PWR handshake */
tps65010_set_low_pwr(ON);
/* Switch VLDO2 to 3.0V for AIC23 */
tps65010_config_vregs1(TPS_LDO2_ENABLE | TPS_VLDO2_3_0V
| TPS_LDO1_ENABLE);
/* register these three LEDs */
osk5912_tps_leds.dev.parent = &client->dev;
platform_device_register(&osk5912_tps_leds);
return 0;
}
