status_t platform_set_periodic_timer(
platform_timer_callback callback,
void *arg, time_t interval)
{
#ifdef PLATFORM_MSM7X30
unsigned val = 0;
unsigned mask = (0x1 << 28);
//Check for the hardware revision
val = readl(HW_REVISION_NUMBER);
if(val & mask)
writel(1, DGT_CLK_CTL);
#endif
enter_critical_section();
timer_callback = callback;
timer_arg = arg;
timer_interval = interval;
writel(timer_interval * (DGT_HZ / 1000), DGT_MATCH_VAL);
writel(0, DGT_CLEAR);
writel(DGT_ENABLE_EN | DGT_ENABLE_CLR_ON_MATCH_EN, DGT_ENABLE);
register_int_handler(INT_DEBUG_TIMER_EXP, timer_irq, 0);
unmask_interrupt(INT_DEBUG_TIMER_EXP);
exit_critical_section();
return 0;
}
status_t ethernet_init(void)
{
/* check to see if the ethernet feature is turned on */
if ((*REG(SYSINFO_FEATURES) & SYSINFO_FEATURE_NETWORK) == 0)
return ERR_NOT_FOUND;
struct netif *netif = calloc(sizeof(struct netif), 1);
struct ip_addr *ipaddr = calloc(sizeof(struct ip_addr), 1);
struct ip_addr *netmask = calloc(sizeof(struct ip_addr), 1);
struct ip_addr *gw = calloc(sizeof(struct ip_addr), 1);
struct netif *netifret = netif_add(netif, ipaddr, netmask, gw, NULL, ðernetif_init, &ip_input);
if (netifret == NULL) {
free(netif);
free(ipaddr);
free(netmask);
free(gw);
return ERR_NOT_FOUND;
}
/* register for interrupt handlers */
register_int_handler(INT_NET, ethernet_int, netif);
netif_set_default(netif);
unmask_interrupt(INT_NET, NULL);
return NO_ERROR;
}
void arm_generic_timer_init(int irq, uint32_t freq_override)
{
uint32_t cntfrq;
if (freq_override == 0) {
cntfrq = read_cntfrq();
if (!cntfrq) {
TRACEF("Failed to initialize timer, frequency is 0\n");
return;
}
} else {
cntfrq = freq_override;
}
#if LOCAL_TRACE
LTRACEF("Test min cntfrq\n");
arm_generic_timer_init_conversion_factors(1);
test_time_conversions(1);
LTRACEF("Test max cntfrq\n");
arm_generic_timer_init_conversion_factors(~0);
test_time_conversions(~0);
LTRACEF("Set actual cntfrq\n");
#endif
arm_generic_timer_init_conversion_factors(cntfrq);
test_time_conversions(cntfrq);
LTRACEF("register irq %d on cpu %d\n", irq, arch_curr_cpu_num());
register_int_handler(irq, &platform_tick, NULL);
unmask_interrupt(irq);
timer_irq = irq;
}
status_t platform_set_periodic_timer(platform_timer_callback callback, void *arg, lk_time_t interval)
{
LTRACEF("callback %p, arg %p, interval %lu\n", callback, arg, interval);
enter_critical_section();
t_callback = callback;
/* disable the timer */
ARM64_WRITE_SYSREG(CNTP_CTL_EL0, 0);
/* set the countdown register to max */
ARM64_WRITE_SYSREG(CNTP_TVAL_EL0, INT32_MAX);
/* calculate the compare delta and set the comparison register */
interval_delta = (uint64_t)timer_freq * interval / 1000U;
last_compare = read_counter() + interval_delta;
ARM64_WRITE_SYSREG(CNTP_CVAL_EL0, last_compare);
ARM64_WRITE_SYSREG(CNTP_CTL_EL0, 1);
unmask_interrupt(INT_PPI_NSPHYS_TIMER);
exit_critical_section();
return NO_ERROR;
}
/* Enable BAM and pipe level interrupts */
void bam_enable_interrupts(struct bam_instance *bam, uint8_t pipe_num)
{
uint32_t int_mask = P_ERR_EN_MASK | P_OUT_OF_DESC_EN_MASK |
P_PRCSD_DESC_EN_MASK | P_TRNSFR_END_EN_MASK;
uint32_t val;
/* Enable BAM error interrupts */
writel(BAM_ERROR_EN_MASK, BAM_IRQ_EN_REG(bam->base));
/* Enable the interrupts for the pipe by enabling the relevant bits
* in the BAM_PIPE_INTERRUPT_ENABLE register.
*/
writel(int_mask,
BAM_P_IRQ_ENn(bam->pipe[pipe_num].pipe_num, bam->base));
/* Enable pipe interrups */
/* Do read-modify-write */
val = readl(BAM_IRQ_SRCS_MSK(bam->base));
writel((1 << bam->pipe[pipe_num].pipe_num) | val,
BAM_IRQ_SRCS_MSK(bam->base));
/* Unmask the QGIC interrupts only in the case of
* interrupt based transfer.
* Use polling othwerwise.
*/
if (bam->pipe[pipe_num].int_mode)
{
/* Register interrupt handler */
register_int_handler(bam->pipe[pipe_num].spi_num, bam_interrupt_handler, 0);
/* Unmask the interrupt */
unmask_interrupt(bam->pipe[pipe_num].spi_num);
}
}
int smd_init(smd_channel_info_t *ch, uint32_t ch_type)
{
unsigned ret = 0;
smd_channel_alloc_entry = (smd_channel_alloc_entry_t*)memalign(CACHE_LINE, SMD_CHANNEL_ALLOC_MAX);
ASSERT(smd_channel_alloc_entry);
ret = smem_read_alloc_entry(SMEM_CHANNEL_ALLOC_TBL,
(void*)smd_channel_alloc_entry,
SMD_CHANNEL_ALLOC_MAX);
if(ret)
{
dprintf(CRITICAL,"ERROR reading smem channel alloc tbl\n");
return -1;
}
smd_get_channel_info(ch, ch_type);
register_int_handler(SMD_IRQ, smd_irq_handler, ch);
unmask_interrupt(SMD_IRQ);
smd_set_state(ch, SMD_SS_OPENING, 1);
smd_notify_rpm();
return 0;
}
void platform_init_timer(void)
{
#if 0
OS_TIMER_CTRL_REG = 0; // stop the timer if it's already running
register_int_handler(IRQ_OS_TIMER, &os_timer_tick, NULL);
unmask_interrupt(IRQ_OS_TIMER, NULL);
#endif
}
void __attribute__((noreturn)) thread_n_main(void)
{
boot_init_thread();
unmask_interrupt(1); // Enable timer interrupt
// Idle task
for (;;)
reschedule();
}
void uart_init(void)
{
/* finish uart init to get rx going */
cbuf_initialize(&uart_rx_buf, 16);
register_int_handler(0x24, uart_irq_handler, NULL);
unmask_interrupt(0x24);
outp(uart_io_port + 1, 0x1); // enable receive data available interrupt
}
static void arm_cortex_a9_timer_init_percpu(uint level)
{
/* disable timer */
TIMREG(TIMER_CONTROL) = 0;
/* kill the watchdog */
TIMREG(WDOG_CONTROL) = 0;
/* ack any irqs that may be pending */
TIMREG(TIMER_ISR) = 1;
/* register the platform tick on each cpu */
register_int_handler(CPU_PRIV_TIMER_INT, &platform_tick, NULL);
unmask_interrupt(CPU_PRIV_TIMER_INT);
}
status_t platform_set_periodic_timer(platform_timer_callback callback, void *arg, lk_time_t interval)
{
enter_critical_section();
t_callback = callback;
periodic_interval = interval;
TIMREG(LOADVAL) = periodic_interval * 1000; /* timer is running at 1Mhz */
TIMREG(CONTROL) |= (1<<7); // enable
unmask_interrupt(TIMER01_INT);
exit_critical_section();
return NO_ERROR;
}
/*
* Function: sdhci msm init
* Arg : MSM specific config data for sdhci
* Return : None
* Flow: : Enable sdhci mode & do msm specific init
*/
void sdhci_msm_init(struct sdhci_host *host, struct sdhci_msm_data *config)
{
/* Disable HC mode */
RMWREG32((config->pwrctl_base + SDCC_MCI_HC_MODE), SDHCI_HC_START_BIT, SDHCI_HC_WIDTH, 0);
/* Core power reset */
RMWREG32((config->pwrctl_base + SDCC_MCI_POWER), CORE_SW_RST_START, CORE_SW_RST_WIDTH, 1);
/* Wait for the core power reset to complete*/
mdelay(1);
/* Enable sdhc mode */
RMWREG32((config->pwrctl_base + SDCC_MCI_HC_MODE), SDHCI_HC_START_BIT, SDHCI_HC_WIDTH, SDHCI_HC_MODE_EN);
/* Set the FF_CLK_SW_RST_DIS to 1 */
RMWREG32((config->pwrctl_base + SDCC_MCI_HC_MODE), FF_CLK_SW_RST_DIS_START, FF_CLK_SW_RST_DIS_WIDTH, 1);
/*
* Reset the controller
*/
sdhci_reset(host, SDHCI_SOFT_RESET);
/*
* CORE_SW_RST may trigger power irq if previous status of PWRCTL
* was either BUS_ON or IO_HIGH. So before we enable the power irq
* interrupt in GIC (by registering the interrupt handler), we need to
* ensure that any pending power irq interrupt status is acknowledged
* otherwise power irq interrupt handler would be fired prematurely.
*/
sdhci_clear_power_ctrl_irq(config);
/*
* Register the interrupt handler for pwr irq
*/
register_int_handler(config->pwr_irq, sdhci_int_handler, (void *)config);
unmask_interrupt(config->pwr_irq);
/* Enable pwr control interrupt */
writel(SDCC_HC_PWR_CTRL_INT, (config->pwrctl_base + SDCC_HC_PWRCTL_MASK_REG));
config->tuning_done = false;
config->calibration_done = false;
host->tuning_in_progress = false;
}
static void imx_uart_init(const void* driver_data, uint32_t length) {
uint32_t regVal;
// create circular buffer to hold received data
cbuf_initialize(&uart_rx_buf, RXBUF_SIZE);
// register uart irq
register_int_handler(uart_irq, &uart_irq_handler, NULL);
// set rx fifo threshold to 1 character
regVal = UARTREG(MX8_UFCR);
regVal &= ~UFCR_RXTL(UFCR_MASK);
regVal &= ~UFCR_TXTL(UFCR_MASK);
regVal |= UFCR_RXTL(1);
regVal |= UFCR_TXTL(0x2);
UARTREG(MX8_UFCR) = regVal;
// enable rx interrupt
regVal = UARTREG(MX8_UCR1);
regVal |= UCR1_RRDYEN;
if (dlog_bypass() == false) {
// enable tx interrupt
regVal |= UCR1_TRDYEN;
}
UARTREG(MX8_UCR1) = regVal;
// enable rx and tx transmisster
regVal = UARTREG(MX8_UCR2);
regVal |= UCR2_RXEN | UCR2_TXEN;
UARTREG(MX8_UCR2) = regVal;
if (dlog_bypass() == true) {
uart_tx_irq_enabled = false;
} else {
/* start up tx driven output */
printf("UART: started IRQ driven TX\n");
uart_tx_irq_enabled = true;
}
initialized = true;
// enable interrupts
unmask_interrupt(uart_irq);
}
int smd_init(smd_channel_info_t *ch, uint32_t ch_type)
{
unsigned ret = 0;
int chnl_found = 0;
uint64_t timeout = SMD_CHANNEL_ACCESS_RETRY;
smd_channel_alloc_entry = (smd_channel_alloc_entry_t*)memalign(CACHE_LINE, SMD_CHANNEL_ALLOC_MAX);
ASSERT(smd_channel_alloc_entry);
dprintf(INFO, "Waiting for the RPM to populate smd channel table\n");
do
{
ret = smem_read_alloc_entry(SMEM_CHANNEL_ALLOC_TBL,
(void*)smd_channel_alloc_entry,
SMD_CHANNEL_ALLOC_MAX);
if(ret)
{
dprintf(CRITICAL,"ERROR reading smem channel alloc tbl\n");
return -1;
}
chnl_found = smd_get_channel_info(ch, ch_type);
timeout--;
udelay(10);
} while(timeout && chnl_found);
if (!timeout)
{
dprintf(CRITICAL, "Apps timed out waiting for RPM-->APPS channel entry\n");
ASSERT(0);
}
register_int_handler(SMD_IRQ, smd_irq_handler, ch);
smd_set_state(ch, SMD_SS_OPENING, 1);
smd_notify_rpm();
unmask_interrupt(SMD_IRQ);
return 0;
}
status_t platform_set_periodic_timer(platform_timer_callback callback, void *arg, lk_time_t interval)
{
enter_critical_section();
t_callback = callback;
callback_arg = arg;
tick_interval = interval;
uint32_t ticks_per_interval = (uint64_t)interval * TIMER_TICK_RATE / 1000; // interval is in ms
TIMER_REG(TCLR) = 0; // stop the timer
TIMER_REG(TLDR) = -ticks_per_interval;
TIMER_REG(TTGR) = 1;
TIMER_REG(TIER) = 0x2;
TIMER_REG(TCLR) = 0x3; // autoreload, start
unmask_interrupt(GPT2_IRQ);
exit_critical_section();
return NO_ERROR;
}
status_t
platform_set_periodic_timer(platform_timer_callback callback,
void *arg, lk_time_t interval)
{
uint32_t tick_count = interval * platform_tick_rate() / 1000;
enter_critical_section();
timer_callback = callback;
timer_arg = arg;
timer_interval = interval;
writel(tick_count, DGT_MATCH_VAL);
writel(0, DGT_CLEAR);
writel(DGT_ENABLE_EN | DGT_ENABLE_CLR_ON_MATCH_EN, DGT_ENABLE);
register_int_handler(INT_DEBUG_TIMER_EXP, timer_irq, 0);
unmask_interrupt(INT_DEBUG_TIMER_EXP);
exit_critical_section();
return 0;
}
status_t platform_set_periodic_timer(platform_timer_callback callback, void *arg, lk_time_t interval)
{
spin_lock_saved_state_t statep;
arch_interrupt_save(&statep, SPIN_LOCK_FLAG_IRQ);
t_callback = callback;
callback_arg = arg;
tick_interval = interval;
uint32_t ticks_per_interval = (uint64_t)interval * TIMER_TICK_RATE / 1000; // interval is in ms
TIMER_REG(TCLR) = 0; // stop the timer
TIMER_REG(TLDR) = -ticks_per_interval;
TIMER_REG(TTGR) = 1;
TIMER_REG(TIER) = 0x2;
TIMER_REG(TCLR) = 0x3; // autoreload, start
unmask_interrupt(GPT2_IRQ);
arch_interrupt_restore(statep, SPIN_LOCK_FLAG_IRQ);
return NO_ERROR;
}
status_t platform_set_periodic_timer(platform_timer_callback callback, void *arg, lk_time_t interval)
{
enter_critical_section();
LTRACEF("callback %p, arg %p, interval %lu\n", callback, arg, interval);
t_callback = callback;
periodic_interval = interval;
uint32_t ticks = periodic_interval * 1000; /* timer is running close to 1Mhz */
ASSERT(ticks <= 0xffff);
TIMREG(IEN(0)) = (1<<0); // interval interrupt
TIMREG(INTERVAL_VAL(0)) = ticks;
TIMREG(CNT_CTRL(0)) = (1<<5) | (1<<4) | (1<<1); // no wave, reset, interval mode
unmask_interrupt(TTC0_A_INT);
exit_critical_section();
return NO_ERROR;
}
status_t
platform_set_periodic_timer(platform_timer_callback callback,
void *arg, lk_time_t interval)
{
uint32_t tick_count = interval * ticks_per_sec / 1000;
spin_lock_saved_state_t state;
spin_lock_irqsave(&lock, state);
timer_callback = callback;
timer_arg = arg;
timer_interval = interval;
writel(tick_count, DGT_MATCH_VAL);
writel(0, DGT_CLEAR);
writel(DGT_ENABLE_EN | DGT_ENABLE_CLR_ON_MATCH_EN, DGT_ENABLE);
register_int_handler(INT_DEBUG_TIMER_EXP, timer_irq, 0);
unmask_interrupt(INT_DEBUG_TIMER_EXP);
spin_unlock_irqrestore(&lock, state);
return 0;
}
status_t platform_set_oneshot_timer (platform_timer_callback callback, void *arg, lk_time_t interval)
{
LTRACEF("callback %p, arg %p, interval %lu\n", callback, arg, interval);
enter_critical_section();
t_callback = callback;
/* disable the timer */
ARM64_WRITE_SYSREG(CNTP_CTL_EL0, 0);
/* set the countdown register to max */
ARM64_WRITE_SYSREG(CNTP_TVAL_EL0, INT32_MAX);
/* calculate the interval */
uint64_t ticks = (uint64_t)timer_freq * interval / 1000U;
/* set the comparison register */
uint64_t counter = read_counter();
counter += ticks;
LTRACEF("new counter 0x%llx ticks %llu\n", counter, ticks);
ARM64_WRITE_SYSREG(CNTP_CVAL_EL0, counter);
/* disable periodic mode */
interval_delta = 0;
/* start the timer, unmask irq */
ARM64_WRITE_SYSREG(CNTP_CTL_EL0, 1);
unmask_interrupt(INT_PPI_NSPHYS_TIMER);
exit_critical_section();
return NO_ERROR;
}
void arm_cortex_a9_timer_init(addr_t _scu_control_base, uint32_t freq)
{
scu_control_base = _scu_control_base;
/* disable timer */
TIMREG(TIMER_CONTROL) = 0;
/* kill the watchdog */
TIMREG(WDOG_CONTROL) = 0;
/* ack any irqs that may be pending */
TIMREG(TIMER_ISR) = 1;
/* save the timer frequency for later calculations */
timer_freq = freq;
/* precompute the conversion factor for global time to real time */
fp_32_64_div_32_32(&timer_freq_msec_conversion, timer_freq, 1000);
fp_32_64_div_32_32(&timer_freq_usec_conversion_inverse, 1000000, timer_freq);
fp_32_64_div_32_32(&timer_freq_msec_conversion_inverse, 1000, timer_freq);
register_int_handler(CPU_PRIV_TIMER_INT, &platform_tick, NULL);
unmask_interrupt(CPU_PRIV_TIMER_INT);
}
void register_interrupt_handler(int interrupt, interrupt_handler_t handler)
{
// XXX lock
handlers[interrupt] = handler;
unmask_interrupt(interrupt);
}
static void arm_generic_timer_init_secondary_cpu(uint level)
{
LTRACEF("register irq %d on cpu %d\n", timer_irq, arch_curr_cpu_num());
register_int_handler(timer_irq, &platform_tick, NULL);
unmask_interrupt(timer_irq);
}
static void pc_init_timer(uint level) {
const struct x86_model_info* cpu_model = x86_get_model();
constant_tsc = false;
if (x86_vendor == X86_VENDOR_INTEL) {
/* This condition taken from Intel 3B 17.15 (Time-Stamp Counter). This
* is the negation of the non-Constant TSC section, since the Constant
* TSC section is incomplete (the behavior is architectural going
* forward, and modern CPUs are not on the list). */
constant_tsc = !((cpu_model->family == 0x6 && cpu_model->model == 0x9) ||
(cpu_model->family == 0x6 && cpu_model->model == 0xd) ||
(cpu_model->family == 0xf && cpu_model->model < 0x3));
}
invariant_tsc = x86_feature_test(X86_FEATURE_INVAR_TSC);
bool has_pvclock = pvclock_is_present();
if (has_pvclock) {
zx_status_t status = pvclock_init();
if (status == ZX_OK) {
invariant_tsc = pvclock_is_stable();
} else {
has_pvclock = false;
}
}
bool has_hpet = hpet_is_present();
if (has_hpet) {
calibration_clock = CLOCK_HPET;
const uint64_t hpet_ms_rate = hpet_ticks_per_ms();
ASSERT(hpet_ms_rate <= UINT32_MAX);
printf("HPET frequency: %" PRIu64 " ticks/ms\n", hpet_ms_rate);
fp_32_64_div_32_32(&ns_per_hpet, 1000 * 1000, static_cast<uint32_t>(hpet_ms_rate));
// Add 1ns to conservatively deal with rounding
ns_per_hpet_rounded_up = u32_mul_u64_fp32_64(1, ns_per_hpet) + 1;
} else {
calibration_clock = CLOCK_PIT;
}
const char* force_wallclock = cmdline_get("kernel.wallclock");
bool use_invariant_tsc = invariant_tsc && (!force_wallclock || !strcmp(force_wallclock, "tsc"));
use_tsc_deadline = use_invariant_tsc &&
x86_feature_test(X86_FEATURE_TSC_DEADLINE);
if (!use_tsc_deadline) {
calibrate_apic_timer();
}
if (use_invariant_tsc) {
calibrate_tsc(has_pvclock);
// Program PIT in the software strobe configuration, but do not load
// the count. This will pause the PIT.
outp(I8253_CONTROL_REG, 0x38);
wall_clock = CLOCK_TSC;
} else {
if (constant_tsc || invariant_tsc) {
// Calibrate the TSC even though it's not as good as we want, so we
// can still let folks still use it for cheap timing.
calibrate_tsc(has_pvclock);
}
if (has_hpet && (!force_wallclock || !strcmp(force_wallclock, "hpet"))) {
wall_clock = CLOCK_HPET;
hpet_set_value(0);
hpet_enable();
} else {
if (force_wallclock && strcmp(force_wallclock, "pit")) {
panic("Could not satisfy kernel.wallclock choice\n");
}
wall_clock = CLOCK_PIT;
set_pit_frequency(1000); // ~1ms granularity
uint32_t irq = apic_io_isa_to_global(ISA_IRQ_PIT);
zx_status_t status = register_int_handler(irq, &pit_timer_tick, NULL);
DEBUG_ASSERT(status == ZX_OK);
unmask_interrupt(irq);
}
}
printf("timer features: constant_tsc %d invariant_tsc %d tsc_deadline %d\n",
constant_tsc, invariant_tsc, use_tsc_deadline);
printf("Using %s as wallclock\n", clock_name[wall_clock]);
}
int msm_i2c_xfer(struct i2c_msg msgs[], int num)
{
int ret, ret_wait;
clk_enable(dev.pdata->clk_nr);
unmask_interrupt(dev.pdata->irq_nr);
ret = msm_i2c_poll_notbusy(1);
if (ret) {
ret = msm_i2c_recover_bus_busy();
if (ret)
goto err;
}
enter_critical_section();
if (dev.flush_cnt) {
I2C_DBG(DEBUGLEVEL, "%d unrequested bytes read\n", dev.flush_cnt);
}
dev.msg = msgs;
dev.rem = num;
dev.pos = -1;
dev.ret = num;
dev.need_flush = false;
dev.flush_cnt = 0;
dev.cnt = msgs->len;
msm_i2c_interrupt_locked();
exit_critical_section();
/*
* Now that we've setup the xfer, the ISR will transfer the data
* and wake us up with dev.err set if there was an error
*/
ret_wait = msm_i2c_poll_notbusy(0); /* Read may not have stopped in time */
enter_critical_section();
if (dev.flush_cnt) {
I2C_DBG(DEBUGLEVEL, "%d unrequested bytes read\n", dev.flush_cnt);
}
ret = dev.ret;
dev.msg = NULL;
dev.rem = 0;
dev.pos = 0;
dev.ret = 0;
dev.flush_cnt = 0;
dev.cnt = 0;
exit_critical_section();
if (ret_wait) {
I2C_DBG(DEBUGLEVEL, "Still busy after xfer completion\n");
ret_wait = msm_i2c_recover_bus_busy();
if (ret_wait)
goto err;
}
if (timeout == ERR_TIMED_OUT) {
I2C_DBG(DEBUGLEVEL, "Transaction timed out\n");
ret = ERR_TIMED_OUT;
}
if (ret < 0) {
I2C_ERR("Error during data xfer (%d)\n", ret);
msm_i2c_recover_bus_busy();
}
/* if (timeout == ERR_TIMED_OUT) {
I2C_DBG(DEBUGLEVEL, "Transaction timed out\n");
ret = 2;
msm_i2c_recover_bus_busy();
}
if (timeout == ERR_TIMED_OUT) {
I2C_DBG(DEBUGLEVEL, "Transaction timed out\n");
ret = ERR_TIMED_OUT;
}
if (ret < 0) {
I2C_ERR("Error during data xfer (%d)\n", ret);
msm_i2c_recover_bus_busy();
} */
err:
mask_interrupt(dev.pdata->irq_nr);
clk_disable(dev.pdata->clk_nr);
return ret;
}
/*
* Function: sdhci msm init
* Arg : MSM specific config data for sdhci
* Return : None
* Flow: : Enable sdhci mode & do msm specific init
*/
void sdhci_msm_init(struct sdhci_host *host, struct sdhci_msm_data *config)
{
uint32_t io_switch;
uint32_t caps = 0;
uint32_t version;
/* Disable HC mode */
RMWREG32((config->pwrctl_base + SDCC_MCI_HC_MODE), SDHCI_HC_START_BIT, SDHCI_HC_WIDTH, 0);
/* Core power reset */
RMWREG32((config->pwrctl_base + SDCC_MCI_POWER), CORE_SW_RST_START, CORE_SW_RST_WIDTH, 1);
/* Wait for the core power reset to complete*/
mdelay(1);
/* Enable sdhc mode */
RMWREG32((config->pwrctl_base + SDCC_MCI_HC_MODE), SDHCI_HC_START_BIT, SDHCI_HC_WIDTH, SDHCI_HC_MODE_EN);
/* Set the FF_CLK_SW_RST_DIS to 1 */
RMWREG32((config->pwrctl_base + SDCC_MCI_HC_MODE), FF_CLK_SW_RST_DIS_START, FF_CLK_SW_RST_DIS_WIDTH, 1);
/*
* Reset the controller
*/
sdhci_reset(host, SDHCI_SOFT_RESET);
/*
* Some platforms have same SDC instance shared between emmc & sd card.
* For such platforms the emmc IO voltage has to be switched from 3.3 to
* 1.8 for the contoller to work with emmc.
*/
if(config->use_io_switch)
{
io_switch = REG_READ32(host, SDCC_VENDOR_SPECIFIC_FUNC);
io_switch |= HC_IO_PAD_PWR_SWITCH | HC_IO_PAD_PWR_SWITCH_EN;
REG_WRITE32(host, io_switch, SDCC_VENDOR_SPECIFIC_FUNC);
}
/*
* CORE_SW_RST may trigger power irq if previous status of PWRCTL
* was either BUS_ON or IO_HIGH. So before we enable the power irq
* interrupt in GIC (by registering the interrupt handler), we need to
* ensure that any pending power irq interrupt status is acknowledged
* otherwise power irq interrupt handler would be fired prematurely.
*/
sdhci_clear_power_ctrl_irq(config);
/*
* Register the interrupt handler for pwr irq
*/
register_int_handler(config->pwr_irq, (int_handler)sdhci_int_handler, (void *)config);
unmask_interrupt(config->pwr_irq);
/* Enable pwr control interrupt */
writel(SDCC_HC_PWR_CTRL_INT, (config->pwrctl_base + SDCC_HC_PWRCTL_MASK_REG));
version = readl(host->msm_host->pwrctl_base + MCI_VERSION);
host->major = (version & CORE_VERSION_MAJOR_MASK) >> CORE_VERSION_MAJOR_SHIFT;
host->minor = (version & CORE_VERSION_MINOR_MASK);
/*
* For SDCC5 the capabilities registers does not have voltage advertised
* Override the values using SDCC_HC_VENDOR_SPECIFIC_CAPABILITIES0
*/
if (host->major >= 1 && host->minor != 0x11 && host->minor != 0x12)
{
caps = REG_READ32(host, SDHCI_CAPS_REG1);
if (config->slot == 0x1)
REG_WRITE32(host, (caps | SDHCI_1_8_VOL_MASK), SDCC_HC_VENDOR_SPECIFIC_CAPABILITIES0);
else
REG_WRITE32(host, (caps | SDHCI_3_0_VOL_MASK), SDCC_HC_VENDOR_SPECIFIC_CAPABILITIES0);
}
config->tuning_done = false;
config->calibration_done = false;
host->tuning_in_progress = false;
}
int virtio_mmio_detect(void *ptr, uint count, const uint irqs[])
{
LTRACEF("ptr %p, count %u\n", ptr, count);
DEBUG_ASSERT(ptr);
DEBUG_ASSERT(irqs);
DEBUG_ASSERT(!devices);
/* allocate an array big enough to hold a list of devices */
devices = calloc(count, sizeof(struct virtio_device));
if (!devices)
return ERR_NO_MEMORY;
int found = 0;
for (uint i = 0; i < count; i++) {
volatile struct virtio_mmio_config *mmio = (struct virtio_mmio_config *)((uint8_t *)ptr + i * 0x200);
struct virtio_device *dev = &devices[i];
dev->index = i;
dev->irq = irqs[i];
mask_interrupt(irqs[i]);
register_int_handler(irqs[i], &virtio_mmio_irq, (void *)dev);
LTRACEF("looking at magic 0x%x version 0x%x did 0x%x vid 0x%x\n",
mmio->magic, mmio->version, mmio->device_id, mmio->vendor_id);
if (mmio->magic != VIRTIO_MMIO_MAGIC) {
continue;
}
#if LOCAL_TRACE
if (mmio->device_id != 0) {
dump_mmio_config(mmio);
}
#endif
#if WITH_DEV_VIRTIO_BLOCK
if (mmio->device_id == 2) { // block device
LTRACEF("found block device\n");
dev->mmio_config = mmio;
dev->config_ptr = (void *)mmio->config;
status_t err = virtio_block_init(dev, mmio->host_features);
if (err >= 0) {
// good device
dev->valid = true;
if (dev->irq_driver_callback)
unmask_interrupt(dev->irq);
// XXX quick test code, remove
#if 0
uint8_t buf[512];
memset(buf, 0x99, sizeof(buf));
virtio_block_read_write(dev, buf, 0, sizeof(buf), false);
hexdump8_ex(buf, sizeof(buf), 0);
buf[0]++;
virtio_block_read_write(dev, buf, 0, sizeof(buf), true);
virtio_block_read_write(dev, buf, 0, sizeof(buf), false);
hexdump8_ex(buf, sizeof(buf), 0);
#endif
}
}
#endif // WITH_DEV_VIRTIO_BLOCK
#if WITH_DEV_VIRTIO_NET
if (mmio->device_id == 1) { // network device
LTRACEF("found net device\n");
dev->mmio_config = mmio;
dev->config_ptr = (void *)mmio->config;
status_t err = virtio_net_init(dev, mmio->host_features);
if (err >= 0) {
// good device
dev->valid = true;
if (dev->irq_driver_callback)
unmask_interrupt(dev->irq);
}
}
#endif // WITH_DEV_VIRTIO_NET
#if WITH_DEV_VIRTIO_GPU
if (mmio->device_id == 0x10) { // virtio-gpu
LTRACEF("found gpu device\n");
dev->mmio_config = mmio;
dev->config_ptr = (void *)mmio->config;
status_t err = virtio_gpu_init(dev, mmio->host_features);
if (err >= 0) {
// good device
dev->valid = true;
if (dev->irq_driver_callback)
unmask_interrupt(dev->irq);
virtio_gpu_start(dev);
}
}
#endif // WITH_DEV_VIRTIO_GPU
if (dev->valid)
found++;
}
return found;
}
