static int otg_init(struct isp1301 *isp)
{
if (!otg_dev)
return -ENODEV;
dump_regs(isp, __func__);
/* some of these values are board-specific... */
OTG_SYSCON_2_REG |= OTG_EN
/* for B-device: */
| SRP_GPDATA /* 9msec Bdev D+ pulse */
| SRP_GPDVBUS /* discharge after VBUS pulse */
// | (3 << 24) /* 2msec VBUS pulse */
/* for A-device: */
| (0 << 20) /* 200ms nominal A_WAIT_VRISE timer */
| SRP_DPW /* detect 167+ns SRP pulses */
| SRP_DATA | SRP_VBUS /* accept both kinds of SRP pulse */
;
update_otg1(isp, isp1301_get_u8(isp, ISP1301_INTERRUPT_SOURCE));
update_otg2(isp, isp1301_get_u8(isp, ISP1301_OTG_STATUS));
check_state(isp, __func__);
pr_debug("otg: %s, %s %06x\n",
state_name(isp), __func__, OTG_CTRL_REG);
OTG_IRQ_EN_REG = DRIVER_SWITCH | OPRT_CHG
| B_SRP_TMROUT | B_HNP_FAIL
| A_VBUS_ERR | A_SRP_DETECT | A_REQ_TMROUT;
OTG_SYSCON_2_REG |= OTG_EN;
return 0;
}
static void isp_update_otg(struct isp1301 *isp, u8 stat)
{
u8 isp_stat, isp_bstat;
enum usb_otg_state state = isp->otg.state;
if (stat & INTR_BDIS_ACON)
pr_debug("OTG: BDIS_ACON, %s\n", state_name(isp));
/* start certain state transitions right away */
isp_stat = isp1301_get_u8(isp, ISP1301_INTERRUPT_SOURCE);
if (isp_stat & INTR_ID_GND) {
if (isp->otg.default_a) {
switch (state) {
case OTG_STATE_B_IDLE:
a_idle(isp, "idle");
/* FALLTHROUGH */
case OTG_STATE_A_IDLE:
enable_vbus_source(isp);
/* FALLTHROUGH */
case OTG_STATE_A_WAIT_VRISE:
/* we skip over OTG_STATE_A_WAIT_BCON, since
* the HC will transition to A_HOST (or
* A_SUSPEND!) without our noticing except
* when HNP is used.
*/
if (isp_stat & INTR_VBUS_VLD)
isp->otg.state = OTG_STATE_A_HOST;
break;
case OTG_STATE_A_WAIT_VFALL:
if (!(isp_stat & INTR_SESS_VLD))
a_idle(isp, "vfell");
break;
default:
if (!(isp_stat & INTR_VBUS_VLD))
isp->otg.state = OTG_STATE_A_VBUS_ERR;
break;
}
isp_bstat = isp1301_get_u8(isp, ISP1301_OTG_STATUS);
} else {
switch (state) {
case OTG_STATE_B_PERIPHERAL:
case OTG_STATE_B_HOST:
case OTG_STATE_B_WAIT_ACON:
usb_gadget_vbus_disconnect(isp->otg.gadget);
break;
default:
break;
}
if (state != OTG_STATE_A_IDLE)
a_idle(isp, "id");
if (isp->otg.host && state == OTG_STATE_A_IDLE)
isp1301_defer_work(isp, WORK_HOST_RESUME);
isp_bstat = 0;
}
} else {
u32 l;
/* if user unplugged mini-A end of cable,
* don't bypass A_WAIT_VFALL.
*/
if (isp->otg.default_a) {
switch (state) {
default:
isp->otg.state = OTG_STATE_A_WAIT_VFALL;
break;
case OTG_STATE_A_WAIT_VFALL:
state = OTG_STATE_A_IDLE;
/* khubd may take a while to notice and
* handle this disconnect, so don't go
* to B_IDLE quite yet.
*/
break;
case OTG_STATE_A_IDLE:
host_suspend(isp);
isp1301_clear_bits(isp, ISP1301_MODE_CONTROL_1,
MC1_BDIS_ACON_EN);
isp->otg.state = OTG_STATE_B_IDLE;
l = omap_readl(OTG_CTRL) & OTG_CTRL_MASK;
l &= ~OTG_CTRL_BITS;
omap_writel(l, OTG_CTRL);
break;
case OTG_STATE_B_IDLE:
break;
}
}
isp_bstat = isp1301_get_u8(isp, ISP1301_OTG_STATUS);
switch (isp->otg.state) {
case OTG_STATE_B_PERIPHERAL:
case OTG_STATE_B_WAIT_ACON:
case OTG_STATE_B_HOST:
if (likely(isp_bstat & OTG_B_SESS_VLD))
break;
enable_vbus_draw(isp, 0);
#ifndef CONFIG_USB_OTG
/* UDC driver will clear OTG_BSESSVLD */
isp1301_set_bits(isp, ISP1301_OTG_CONTROL_1,
OTG1_DP_PULLDOWN);
isp1301_clear_bits(isp, ISP1301_OTG_CONTROL_1,
OTG1_DP_PULLUP);
dump_regs(isp, __func__);
#endif
/* FALLTHROUGH */
case OTG_STATE_B_SRP_INIT:
b_idle(isp, __func__);
l = omap_readl(OTG_CTRL) & OTG_XCEIV_OUTPUTS;
omap_writel(l, OTG_CTRL);
/* FALLTHROUGH */
case OTG_STATE_B_IDLE:
if (isp->otg.gadget && (isp_bstat & OTG_B_SESS_VLD)) {
#ifdef CONFIG_USB_OTG
update_otg1(isp, isp_stat);
update_otg2(isp, isp_bstat);
#endif
b_peripheral(isp);
} else if (!(isp_stat & (INTR_VBUS_VLD|INTR_SESS_VLD)))
isp_bstat |= OTG_B_SESS_END;
break;
case OTG_STATE_A_WAIT_VFALL:
break;
default:
pr_debug("otg: unsupported b-device %s\n",
state_name(isp));
break;
}
}
if (state != isp->otg.state)
pr_debug(" isp, %s -> %s\n",
state_string(state), state_name(isp));
#ifdef CONFIG_USB_OTG
/* update the OTG controller state to match the isp1301; may
* trigger OPRT_CHG irqs for changes going to the isp1301.
*/
update_otg1(isp, isp_stat);
update_otg2(isp, isp_bstat);
check_state(isp, __func__);
#endif
dump_regs(isp, "isp1301->otg");
}
static int __init
isp1301_probe(struct i2c_client *i2c, const struct i2c_device_id *id)
{
int status;
struct isp1301 *isp;
if (the_transceiver)
return 0;
isp = kzalloc(sizeof *isp, GFP_KERNEL);
if (!isp)
return 0;
INIT_WORK(&isp->work, isp1301_work);
init_timer(&isp->timer);
isp->timer.function = isp1301_timer;
isp->timer.data = (unsigned long) isp;
i2c_set_clientdata(i2c, isp);
isp->client = i2c;
/* verify the chip (shouldn't be necesary) */
status = isp1301_get_u16(isp, ISP1301_VENDOR_ID);
if (status != I2C_VENDOR_ID_PHILIPS) {
dev_dbg(&i2c->dev, "not philips id: %d\n", status);
goto fail;
}
status = isp1301_get_u16(isp, ISP1301_PRODUCT_ID);
if (status != I2C_PRODUCT_ID_PHILIPS_1301) {
dev_dbg(&i2c->dev, "not isp1301, %d\n", status);
goto fail;
}
isp->i2c_release = i2c->dev.release;
i2c->dev.release = isp1301_release;
/* initial development used chiprev 2.00 */
status = i2c_smbus_read_word_data(i2c, ISP1301_BCD_DEVICE);
dev_info(&i2c->dev, "chiprev %x.%02x, driver " DRIVER_VERSION "\n",
status >> 8, status & 0xff);
/* make like power-on reset */
isp1301_clear_bits(isp, ISP1301_MODE_CONTROL_1, MC1_MASK);
isp1301_set_bits(isp, ISP1301_MODE_CONTROL_2, MC2_BI_DI);
isp1301_clear_bits(isp, ISP1301_MODE_CONTROL_2, ~MC2_BI_DI);
isp1301_set_bits(isp, ISP1301_OTG_CONTROL_1,
OTG1_DM_PULLDOWN | OTG1_DP_PULLDOWN);
isp1301_clear_bits(isp, ISP1301_OTG_CONTROL_1,
~(OTG1_DM_PULLDOWN | OTG1_DP_PULLDOWN));
isp1301_clear_bits(isp, ISP1301_INTERRUPT_LATCH, ~0);
isp1301_clear_bits(isp, ISP1301_INTERRUPT_FALLING, ~0);
isp1301_clear_bits(isp, ISP1301_INTERRUPT_RISING, ~0);
#ifdef CONFIG_USB_OTG
status = otg_bind(isp);
if (status < 0) {
dev_dbg(&i2c->dev, "can't bind OTG\n");
goto fail;
}
#endif
if (machine_is_omap_h2()) {
/* full speed signaling by default */
isp1301_set_bits(isp, ISP1301_MODE_CONTROL_1,
MC1_SPEED);
isp1301_set_bits(isp, ISP1301_MODE_CONTROL_2,
MC2_SPD_SUSP_CTRL);
/* IRQ wired at M14 */
omap_cfg_reg(M14_1510_GPIO2);
if (gpio_request(2, "isp1301") == 0)
gpio_direction_input(2);
isp->irq_type = IRQF_TRIGGER_FALLING;
}
isp->irq_type |= IRQF_SAMPLE_RANDOM;
status = request_irq(i2c->irq, isp1301_irq,
isp->irq_type, DRIVER_NAME, isp);
if (status < 0) {
dev_dbg(&i2c->dev, "can't get IRQ %d, err %d\n",
i2c->irq, status);
goto fail;
}
isp->otg.dev = &i2c->dev;
isp->otg.label = DRIVER_NAME;
isp->otg.set_host = isp1301_set_host,
isp->otg.set_peripheral = isp1301_set_peripheral,
isp->otg.set_power = isp1301_set_power,
isp->otg.start_srp = isp1301_start_srp,
isp->otg.start_hnp = isp1301_start_hnp,
enable_vbus_draw(isp, 0);
power_down(isp);
the_transceiver = isp;
#ifdef CONFIG_USB_OTG
update_otg1(isp, isp1301_get_u8(isp, ISP1301_INTERRUPT_SOURCE));
update_otg2(isp, isp1301_get_u8(isp, ISP1301_OTG_STATUS));
#endif
dump_regs(isp, __func__);
#ifdef VERBOSE
mod_timer(&isp->timer, jiffies + TIMER_JIFFIES);
dev_dbg(&i2c->dev, "scheduled timer, %d min\n", TIMER_MINUTES);
#endif
status = otg_set_transceiver(&isp->otg);
if (status < 0)
dev_err(&i2c->dev, "can't register transceiver, %d\n",
status);
return 0;
fail:
kfree(isp);
return -ENODEV;
}
/* no error returns, they'd just make bus scanning stop */
static int isp1301_probe(struct i2c_adapter *bus, int address, int kind)
{
int status;
struct isp1301 *isp;
struct i2c_client *i2c;
if (the_transceiver)
return 0;
isp = kzalloc(sizeof *isp, GFP_KERNEL);
if (!isp)
return 0;
INIT_WORK(&isp->work, isp1301_work, isp);
init_timer(&isp->timer);
isp->timer.function = isp1301_timer;
isp->timer.data = (unsigned long) isp;
isp->irq = -1;
isp->client.addr = address;
i2c_set_clientdata(&isp->client, isp);
isp->client.adapter = bus;
isp->client.driver = &isp1301_driver;
strlcpy(isp->client.name, DRIVER_NAME, I2C_NAME_SIZE);
i2c = &isp->client;
/* if this is a true probe, verify the chip ... */
if (kind < 0) {
status = isp1301_get_u16(isp, ISP1301_VENDOR_ID);
if (status != I2C_VENDOR_ID_PHILIPS) {
dev_dbg(&bus->dev, "addr %d not philips id: %d\n",
address, status);
goto fail1;
}
status = isp1301_get_u16(isp, ISP1301_PRODUCT_ID);
if (status != I2C_PRODUCT_ID_PHILIPS_1301) {
dev_dbg(&bus->dev, "%d not isp1301, %d\n",
address, status);
goto fail1;
}
}
status = i2c_attach_client(i2c);
if (status < 0) {
dev_dbg(&bus->dev, "can't attach %s to device %d, err %d\n",
DRIVER_NAME, address, status);
fail1:
kfree(isp);
return 0;
}
isp->i2c_release = i2c->dev.release;
i2c->dev.release = isp1301_release;
/* initial development used chiprev 2.00 */
status = i2c_smbus_read_word_data(i2c, ISP1301_BCD_DEVICE);
dev_info(&i2c->dev, "chiprev %x.%02x, driver " DRIVER_VERSION "\n",
status >> 8, status & 0xff);
/* make like power-on reset */
isp1301_clear_bits(isp, ISP1301_MODE_CONTROL_1, MC1_MASK);
isp1301_set_bits(isp, ISP1301_MODE_CONTROL_2, MC2_BI_DI);
isp1301_clear_bits(isp, ISP1301_MODE_CONTROL_2, ~MC2_BI_DI);
isp1301_set_bits(isp, ISP1301_OTG_CONTROL_1,
OTG1_DM_PULLDOWN | OTG1_DP_PULLDOWN);
isp1301_clear_bits(isp, ISP1301_OTG_CONTROL_1,
~(OTG1_DM_PULLDOWN | OTG1_DP_PULLDOWN));
isp1301_clear_bits(isp, ISP1301_INTERRUPT_LATCH, ~0);
isp1301_clear_bits(isp, ISP1301_INTERRUPT_FALLING, ~0);
isp1301_clear_bits(isp, ISP1301_INTERRUPT_RISING, ~0);
#ifdef CONFIG_USB_OTG
status = otg_bind(isp);
if (status < 0) {
dev_dbg(&i2c->dev, "can't bind OTG\n");
goto fail2;
}
#endif
if (machine_is_omap_h2()) {
/* full speed signaling by default */
isp1301_set_bits(isp, ISP1301_MODE_CONTROL_1,
MC1_SPEED_REG);
isp1301_set_bits(isp, ISP1301_MODE_CONTROL_2,
MC2_SPD_SUSP_CTRL);
/* IRQ wired at M14 */
omap_cfg_reg(M14_1510_GPIO2);
isp->irq = OMAP_GPIO_IRQ(2);
omap_request_gpio(2);
omap_set_gpio_direction(2, 1);
omap_set_gpio_edge_ctrl(2, OMAP_GPIO_FALLING_EDGE);
}
status = request_irq(isp->irq, isp1301_irq,
IRQF_SAMPLE_RANDOM, DRIVER_NAME, isp);
if (status < 0) {
dev_dbg(&i2c->dev, "can't get IRQ %d, err %d\n",
isp->irq, status);
#ifdef CONFIG_USB_OTG
fail2:
#endif
i2c_detach_client(i2c);
goto fail1;
}
isp->otg.dev = &isp->client.dev;
isp->otg.label = DRIVER_NAME;
isp->otg.set_host = isp1301_set_host,
isp->otg.set_peripheral = isp1301_set_peripheral,
isp->otg.set_power = isp1301_set_power,
isp->otg.start_srp = isp1301_start_srp,
isp->otg.start_hnp = isp1301_start_hnp,
enable_vbus_draw(isp, 0);
power_down(isp);
the_transceiver = isp;
#ifdef CONFIG_USB_OTG
update_otg1(isp, isp1301_get_u8(isp, ISP1301_INTERRUPT_SOURCE));
update_otg2(isp, isp1301_get_u8(isp, ISP1301_OTG_STATUS));
#endif
dump_regs(isp, __FUNCTION__);
#ifdef VERBOSE
mod_timer(&isp->timer, jiffies + TIMER_JIFFIES);
dev_dbg(&i2c->dev, "scheduled timer, %d min\n", TIMER_MINUTES);
#endif
status = otg_set_transceiver(&isp->otg);
if (status < 0)
dev_err(&i2c->dev, "can't register transceiver, %d\n",
status);
return 0;
}