/*
* Initialize Local Bus
*/
void local_bus_init (void)
{
volatile fsl_lbc_t *lbc = LBC_BASE_ADDR;
volatile ccsr_local_ecm_t *ecm = (void *)(CONFIG_SYS_MPC85xx_ECM_ADDR);
sys_info_t sysinfo;
uint clkdiv;
uint lbc_mhz;
uint lcrr = CONFIG_SYS_LBC_LCRR;
get_sys_info (&sysinfo);
clkdiv = lbc->lcrr & LCRR_CLKDIV;
lbc_mhz = sysinfo.freq_systembus / 1000000 / clkdiv;
/* Disable PLL bypass for Local Bus Clock >= 66 MHz */
if (lbc_mhz >= 66)
lcrr &= ~LCRR_DBYP; /* DLL Enabled */
else
lcrr |= LCRR_DBYP; /* DLL Bypass */
out_be32 (&lbc->lcrr, lcrr);
asm ("sync;isync;msync");
out_be32 (&lbc->ltesr, 0xffffffff); /* Clear LBC error interrupts */
out_be32 (&lbc->lteir, 0xffffffff); /* Enable LBC error interrupts */
out_be32 (&ecm->eedr, 0xffffffff); /* Clear ecm errors */
out_be32 (&ecm->eeer, 0xffffffff); /* Enable ecm errors */
/* Init UPMA for FPGA access */
out_be32 (&lbc->mamr, 0x44440); /* Use a customer-supplied value */
upmconfig (UPMA, (uint *)UPMTableA, sizeof(UPMTableA)/sizeof(int));
/* Init UPMB for Lime controller access */
out_be32 (&lbc->mbmr, 0x444440); /* Use a customer-supplied value */
upmconfig (UPMB, (uint *)UPMTableB, sizeof(UPMTableB)/sizeof(int));
}
phys_size_t initdram (int board_type)
{
volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
volatile memctl8xx_t *memctl = &immap->im_memctl;
long int size_b0;
memctl->memc_or2 = CONFIG_SYS_OR2;
memctl->memc_br2 = CONFIG_SYS_BR2;
udelay(100);
upmconfig(UPMA, (uint *)sdram_table, sizeof(sdram_table)/sizeof(uint));
memctl->memc_mptpr = MPTPR_PTP_DIV16;
memctl->memc_mamr = CONFIG_SYS_MAMR_48_SDR | MAMR_TLFA_1X;
/*Do the initialization of the SDRAM*/
/*Start with the precharge cycle*/
memctl->memc_mcr = (MCR_OP_RUN | MCR_UPM_A | MCR_MB_CS2 | \
MCR_MLCF(1) | MCR_MAD(0x5));
/*Then we need two refresh cycles*/
memctl->memc_mamr = CONFIG_SYS_MAMR_48_SDR | MAMR_TLFA_2X;
memctl->memc_mcr = (MCR_OP_RUN | MCR_UPM_A | MCR_MB_CS2 | \
MCR_MLCF(2) | MCR_MAD(0x30));
/*Mode register programming*/
memctl->memc_mar = 0x00000088; /*CAS Latency = 2 and burst length = 4*/
memctl->memc_mcr = (MCR_OP_RUN | MCR_UPM_A | MCR_MB_CS2 | \
MCR_MLCF(1) | MCR_MAD(0x1C));
/* That should do it, just enable the periodic refresh in burst of 4*/
memctl->memc_mamr = CONFIG_SYS_MAMR_48_SDR | MAMR_TLFA_4X;
memctl->memc_mamr |= (MAMR_PTAE | MAMR_GPL_A4DIS);
size_b0 = 16*1024*1024;
/*
* No bank 1 or 3
* invalidate bank
*/
memctl->memc_br1 = 0;
memctl->memc_br3 = 0;
upmconfig(UPMB, (uint *)dsp_disp_table, sizeof(dsp_disp_table)/sizeof(uint));
memctl->memc_mbmr = MBMR_GPL_B4DIS;
memctl->memc_or4 = CONFIG_SYS_OR4;
memctl->memc_br4 = CONFIG_SYS_BR4;
return (size_b0);
}
int board_nand_init(struct nand_chip *nand)
{
static int UpmInit = 0;
volatile immap_t * immr = (immap_t *)CONFIG_SYS_IMMR;
volatile memctl8260_t *memctl = &immr->im_memctl;
if (hwinf.nand == 0) return -1;
/* Setup the UPM */
if (UpmInit == 0) {
switch (hwinf.busclk_real) {
case 100000000:
upmconfig (UPMB, (uint *) upmTable100,
sizeof (upmTable100) / sizeof (uint));
break;
case 133333333:
upmconfig (UPMB, (uint *) upmTable133,
sizeof (upmTable133) / sizeof (uint));
break;
default:
upmconfig (UPMB, (uint *) upmTable67,
sizeof (upmTable67) / sizeof (uint));
break;
}
UpmInit = 1;
}
/* Setup the memctrl */
memctl->memc_or3 = CONFIG_SYS_NAND_OR;
memctl->memc_br3 = CONFIG_SYS_NAND_BR;
memctl->memc_mbmr = (MxMR_OP_NORM);
nand->ecc.mode = NAND_ECC_SOFT;
nand->cmd_ctrl = upmnand_hwcontrol;
nand->read_byte = upmnand_read_byte;
nand->dev_ready = tqm8272_dev_ready;
#ifndef CONFIG_NAND_SPL
nand->write_buf = tqm8272_write_buf;
nand->read_buf = tqm8272_read_buf;
nand->verify_buf = tqm8272_verify_buf;
#endif
/*
* Select required NAND chip
*/
board_nand_select_device(nand, 0);
return 0;
}
phys_size_t initdram (int board_type)
{
volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
volatile memctl8xx_t *memctl = &immap->im_memctl;
/* AMX860: has 4 Mb of 60ns EDO DRAM, so start DRAM at 0 */
upmconfig(UPMA, (uint *) edo_60ns, sizeof(edo_60ns)/sizeof(uint));
#ifndef CONFIG_AMX_RAM_EXT
memctl->memc_mptpr = 0x0400; /* divide by 16 */
#else
memctl->memc_mptpr = 0x0200;
#endif
memctl->memc_mamr = 0x30a21114;
memctl->memc_or2 = 0xffc00800;
#ifndef CONFIG_AMX_RAM_EXT
memctl->memc_br2 = 0x81;
return (4 << 20);
#else
memctl->memc_or1 = 0xff000800;
memctl->memc_br1 = 0x00000081;
memctl->memc_br2 = 0x01000081;
return (20 << 20);
#endif
}
phys_size_t initdram (int board_type)
{
long int msize;
volatile immap_t *immap = (volatile immap_t *)CONFIG_SYS_IMMR;
volatile memctl8xx_t *memctl = &immap->im_memctl;
upmconfig(UPMA, sdram_table, sizeof(sdram_table) / sizeof(uint));
/* Configure SDRAM refresh */
memctl->memc_mptpr = MPTPR_PTP_DIV2; /* BRGCLK/2 */
memctl->memc_mamr = (65 << 24) | CONFIG_SYS_MAMR; /* No refresh */
udelay(100);
/* Run MRS pattern from location 0x36 */
memctl->memc_mar = 0x88;
memctl->memc_mcr = 0x80002236;
udelay(100);
memctl->memc_mamr |= MAMR_PTAE; /* Enable refresh */
memctl->memc_or1 = ~(CONFIG_SYS_SDRAM_MAX_SIZE - 1) | OR_CSNT_SAM;
memctl->memc_br1 = CONFIG_SYS_SDRAM_BASE | BR_PS_32 | BR_MS_UPMA | BR_V;
msize = get_ram_size(CONFIG_SYS_SDRAM_BASE, CONFIG_SYS_SDRAM_MAX_SIZE);
memctl->memc_or1 |= ~(msize - 1);
return msize;
}
static int _initsdram(uint base, uint noMbytes)
{
volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
volatile memctl8xx_t *memctl = &immap->im_memctl;
upmconfig(UPMB, (uint *)sdram_table,sizeof(sdram_table)/sizeof(uint));
memctl->memc_mptpr = MPTPR_2BK_4K;
memctl->memc_mbmr = SDRAM_MxMR_8COL & (~(MBMR_PTBE)); /* no refresh yet */
/* map CS 4 */
memctl->memc_or4 = SDRAM_OR4VALUE | ~((noMbytes<<20)-1);
memctl->memc_br4 = SDRAM_BR4VALUE | base;
/* Perform SDRAM initilization */
# ifdef UPM_NOP_ADDR /* not currently in UPM table */
/* step 1: nop */
memctl->memc_mar = 0x00000000;
memctl->memc_mcr = MCR_UPM_B | MCR_OP_RUN | MCR_MB_CS4 |
MCR_MLCF(0) | UPM_NOP_ADDR;
# endif
/* step 2: delay */
udelay(200);
# ifdef UPM_PRECHARGE_ADDR /* merged with MRS in UPM table */
/* step 3: precharge */
memctl->memc_mar = 0x00000000;
memctl->memc_mcr = MCR_UPM_B | MCR_OP_RUN | MCR_MB_CS4 |
MCR_MLCF(4) | UPM_PRECHARGE_ADDR;
# endif
/* step 4: refresh */
memctl->memc_mar = 0x00000000;
memctl->memc_mcr = MCR_UPM_B | MCR_OP_RUN | MCR_MB_CS4 |
MCR_MLCF(2) | UPM_REFRESH_ADDR;
/*
* note: for some reason, the UPM values we are using include
* precharge with MRS
*/
/* step 5: mrs */
memctl->memc_mar = 0x00000088;
memctl->memc_mcr = MCR_UPM_B | MCR_OP_RUN | MCR_MB_CS4 |
MCR_MLCF(1) | UPM_MRS_ADDR;
# ifdef UPM_NOP_ADDR
memctl->memc_mar = 0x00000000;
memctl->memc_mcr = MCR_UPM_B | MCR_OP_RUN | MCR_MB_CS4 |
MCR_MLCF(0) | UPM_NOP_ADDR;
# endif
/*
* Enable refresh
*/
memctl->memc_mbmr |= MBMR_PTBE;
return 0;
}
/*
* Initialize SDRAM
*/
long int initdram (int board_type)
{
volatile immap_t *immr = (immap_t *) CFG_IMMR;
volatile memctl8xx_t *memctl = &immr->im_memctl;
upmconfig (UPMA,
(uint *) sdram_upm_table,
sizeof (sdram_upm_table) / sizeof (uint)
);
/*
* Setup MAMR register
*/
memctl->memc_mptpr = CFG_MPTPR_1BK_8K;
memctl->memc_mamr = CFG_MAMR_8COL & (~(MAMR_PTAE)); /* no refresh yet */
/*
* Map CS1* to SDRAM bank
*/
memctl->memc_or1 = CFG_OR1;
memctl->memc_br1 = CFG_BR1;
/*
* Perform SDRAM initialization sequence:
* 1. Apply at least one NOP command
* 2. 100 uS delay (JEDEC standard says 200 uS)
* 3. Issue 4 precharge commands
* 4. Perform two refresh cycles
* 5. Program mode register
*
* Program SDRAM for standard operation, sequential burst, burst length
* of 4, CAS latency of 2.
*/
memctl->memc_mar = 0x00000000;
memctl->memc_mcr = MCR_UPM_A | MCR_OP_RUN | MCR_MB_CS1 |
MCR_MLCF (0) | UPMA_NOP_ADDR;
udelay (200);
memctl->memc_mar = 0x00000000;
memctl->memc_mcr = MCR_UPM_A | MCR_OP_RUN | MCR_MB_CS1 |
MCR_MLCF (4) | UPMA_PRECHARGE_ADDR;
memctl->memc_mar = 0x00000000;
memctl->memc_mcr = MCR_UPM_A | MCR_OP_RUN | MCR_MB_CS1 |
MCR_MLCF (2) | UPM_REFRESH_ADDR;
memctl->memc_mar = 0x00000088;
memctl->memc_mcr = MCR_UPM_A | MCR_OP_RUN | MCR_MB_CS1 |
MCR_MLCF (1) | UPMA_MRS_ADDR;
memctl->memc_mar = 0x00000000;
memctl->memc_mcr = MCR_UPM_A | MCR_OP_RUN | MCR_MB_CS1 |
MCR_MLCF (0) | UPMA_NOP_ADDR;
/*
* Enable refresh
*/
memctl->memc_mamr |= MAMR_PTAE;
return (SDRAM_SIZE);
}
int
misc_init_f (void)
{
volatile immap_t *immap = (immap_t *) CFG_IMMR;
volatile memctl8260_t *memctl = &immap->im_memctl;
printf ("UPMs: ");
upmconfig (UPMB, upmb_table, sizeof upmb_table / sizeof upmb_table[0]);
memctl->memc_mbmr = CFG_MBMR;
upmconfig (UPMC, upmc_table, sizeof upmc_table / sizeof upmc_table[0]);
memctl->memc_mcmr = CFG_MCMR;
printf ("configured\n");
return (0);
}
void doc_init (void)
{
volatile immap_t *immap = (immap_t *) CFG_IMMR;
volatile memctl8xx_t *memctl = &immap->im_memctl;
upmconfig (UPMB, (uint *) static_table,
sizeof (static_table) / sizeof (uint));
memctl->memc_mbmr = MAMR_DSA_1_CYCL;
doc_probe (FLASH_BASE1_PRELIM);
}
int board_early_init_f(void)
{
volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
volatile iop8xx_t *ioport = &immap->im_ioport;
volatile cpm8xx_t *cpm = &immap->im_cpm;
volatile memctl8xx_t *memctl = &immap->im_memctl;
/* NAND chip select */
#if CONFIG_NETPHONE_VERSION == 1
memctl->memc_or1 = ((0xFFFFFFFFLU & ~(NAND_SIZE - 1)) | OR_CSNT_SAM | OR_BI | OR_SCY_8_CLK | OR_EHTR | OR_TRLX);
memctl->memc_br1 = ((NAND_BASE & BR_BA_MSK) | BR_PS_8 | BR_V);
#elif CONFIG_NETPHONE_VERSION == 2
upmconfig(UPMA, (uint *) nandcs_table, sizeof(nandcs_table) / sizeof(nandcs_table[0]));
memctl->memc_or1 = ((0xFFFFFFFFLU & ~(NAND_SIZE - 1)) | OR_BI | OR_G5LS);
memctl->memc_br1 = ((NAND_BASE & BR_BA_MSK) | BR_PS_8 | BR_V | BR_MS_UPMA);
memctl->memc_mamr = 0; /* all clear */
#endif
/* DSP chip select */
memctl->memc_or2 = ((0xFFFFFFFFLU & ~(DSP_SIZE - 1)) | OR_CSNT_SAM | OR_BI | OR_ACS_DIV2 | OR_SETA | OR_TRLX);
memctl->memc_br2 = ((DSP_BASE & BR_BA_MSK) | BR_PS_16 | BR_V);
#if CONFIG_NETPHONE_VERSION == 1
memctl->memc_br4 &= ~BR_V;
#endif
memctl->memc_br5 &= ~BR_V;
memctl->memc_br6 &= ~BR_V;
memctl->memc_br7 &= ~BR_V;
ioport->iop_padat = PA_GP_OUTVAL;
ioport->iop_paodr = PA_ODR_VAL;
ioport->iop_padir = PA_GP_OUTMASK | PA_SP_DIRVAL;
ioport->iop_papar = PA_SP_MASK;
cpm->cp_pbdat = PB_GP_OUTVAL;
cpm->cp_pbodr = PB_ODR_VAL;
cpm->cp_pbdir = PB_GP_OUTMASK | PB_SP_DIRVAL;
cpm->cp_pbpar = PB_SP_MASK;
ioport->iop_pcdat = PC_GP_OUTVAL;
ioport->iop_pcdir = PC_GP_OUTMASK | PC_SP_DIRVAL;
ioport->iop_pcso = PC_SOVAL;
ioport->iop_pcint = PC_INTVAL;
ioport->iop_pcpar = PC_SP_MASK;
cpm->cp_pedat = PE_GP_OUTVAL;
cpm->cp_peodr = PE_ODR_VAL;
cpm->cp_pedir = PE_GP_OUTMASK | PE_SP_DIRVAL;
cpm->cp_pepar = PE_SP_MASK;
return 0;
}
int board_early_init_r(void)
{
struct km_bec_fpga *base =
(struct km_bec_fpga *)CONFIG_SYS_KMBEC_FPGA_BASE;
#if defined(CONFIG_SUVD3)
immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
fsl_lbc_t *lbc = &immap->im_lbc;
u32 *mxmr = &lbc->mamr;
#endif
#if defined(CONFIG_MPC8360)
unsigned short svid;
/*
* Because of errata in the UCCs, we have to write to the reserved
* registers to slow the clocks down.
*/
svid = SVR_REV(mfspr(SVR));
switch (svid) {
case 0x0020:
/*
* MPC8360ECE.pdf QE_ENET10 table 4:
* IMMR + 0x14A8[4:5] = 11 (clk delay for UCC 2)
* IMMR + 0x14A8[18:19] = 11 (clk delay for UCC 1)
*/
setbits_be32((void *)(CONFIG_SYS_IMMR + 0x14a8), 0x0c003000);
break;
case 0x0021:
/*
* MPC8360ECE.pdf QE_ENET10 table 4:
* IMMR + 0x14AC[24:27] = 1010
*/
clrsetbits_be32((void *)(CONFIG_SYS_IMMR + 0x14ac),
0x00000050, 0x000000a0);
break;
}
#endif
/* enable the PHY on the PIGGY */
setbits_8(&base->pgy_eth, 0x01);
/* enable the Unit LED (green) */
setbits_8(&base->oprth, WRL_BOOT);
/* enable Application Buffer */
setbits_8(&base->oprtl, OPRTL_XBUFENA);
#if defined(CONFIG_SUVD3)
/* configure UPMA for APP1 */
upmconfig(UPMA, (uint *) upma_table,
sizeof(upma_table) / sizeof(uint));
out_be32(mxmr, CONFIG_SYS_MAMR);
#endif
return 0;
}
phys_size_t initdram (int board_type)
{
volatile immap_t *immap = (immap_t *)CFG_IMMR;
volatile memctl8xx_t *memctl = &immap->im_memctl;
long int size_b0 = 0;
upmconfig(UPMA, (uint *)sdram_table, sizeof(sdram_table)/sizeof(uint));
memctl->memc_mptpr = CFG_MPTPR;
#if defined (CONFIG_SDRAM_16M)
memctl->memc_mamr = 0x00802114 | CFG_MxMR_PTx;
memctl->memc_mcr = 0x80002105; /* SDRAM bank 0 */
udelay(1);
memctl->memc_mcr = 0x80002830;
udelay(1);
memctl->memc_mar = 0x00000088;
udelay(1);
memctl->memc_mcr = 0x80002106;
udelay(1);
memctl->memc_or1 = 0xff000a00;
size_b0 = 0x01000000;
#elif defined (CONFIG_SDRAM_32M)
memctl->memc_mamr = 0x00904114 | CFG_MxMR_PTx;
memctl->memc_mcr = 0x80002105; /* SDRAM bank 0 */
udelay(1);
memctl->memc_mcr = 0x80002830;
udelay(1);
memctl->memc_mar = 0x00000088;
udelay(1);
memctl->memc_mcr = 0x80002106;
udelay(1);
memctl->memc_or1 = 0xfe000a00;
size_b0 = 0x02000000;
#elif defined (CONFIG_SDRAM_64M)
memctl->memc_mamr = 0x00a04114 | CFG_MxMR_PTx;
memctl->memc_mcr = 0x80002105; /* SDRAM bank 0 */
udelay(1);
memctl->memc_mcr = 0x80002830;
udelay(1);
memctl->memc_mar = 0x00000088;
udelay(1);
memctl->memc_mcr = 0x80002106;
udelay(1);
memctl->memc_or1 = 0xfc000a00;
size_b0 = 0x04000000;
#else
#error SDRAM size configuration missing.
#endif
memctl->memc_br1 = 0x00000081;
udelay(200);
return (size_b0 );
}
static int _initsdram(uint base, uint noMbytes)
{
volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
volatile memctl8xx_t *memctl = &immap->im_memctl;
upmconfig(UPMB, (uint *)sdram_table,sizeof(sdram_table)/sizeof(uint));
memctl->memc_mptpr = SDRAM_MPTPRVALUE;
/* Configure the refresh (mostly). This needs to be
* based upon processor clock speed and optimized to provide
* the highest level of performance. For multiple banks,
* this time has to be divided by the number of banks.
* Although it is not clear anywhere, it appears the
* refresh steps through the chip selects for this UPM
* on each refresh cycle.
* We have to be careful changing
* UPM registers after we ask it to run these commands.
*/
memctl->memc_mbmr = SDRAM_MBMRVALUE0; /* TLF 4 */
memctl->memc_mar = SDRAM_MARVALUE; /* MRS code */
udelay(200);
/* Now run the precharge/nop/mrs commands.
*/
memctl->memc_mcr = 0x80808111; /* run umpb cs4 1 count 1, addr 0x11 ??? (50MHz) */
/* run umpb cs4 1 count 1, addr 0x11 precharge+MRS (100MHz) */
udelay(200);
/* Run 8 refresh cycles */
memctl->memc_mcr = SDRAM_MCRVALUE0; /* run upmb cs4 loop 1 addr 0x5 precharge+MRS (50 MHz)*/
/* run upmb cs4 loop 1 addr 0x11 precharge+MRS (100MHz) */
udelay(200);
memctl->memc_mbmr = SDRAM_MBMRVALUE1; /* TLF 4 (100 MHz) or TLF 8 (50MHz) */
memctl->memc_mcr = SDRAM_MCRVALUE1; /* run upmb cs4 loop 1 addr 0x30 refr (50 MHz) */
/* run upmb cs4 loop 1 addr 0x11 precharge+MRS ??? (100MHz) */
udelay(200);
memctl->memc_mbmr = SDRAM_MBMRVALUE0; /* TLF 4 */
memctl->memc_or4 = SDRAM_OR4VALUE | ~((noMbytes<<20)-1);
memctl->memc_br4 = SDRAM_BR4VALUE | base;
return 0;
}
phys_size_t initdram (int board_type)
{
volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
volatile memctl8xx_t *memctl = &immap->im_memctl;
long int size9;
upmconfig(UPMA, (uint *)sdram_table, sizeof(sdram_table)/sizeof(uint));
/* Refresh clock prescalar */
memctl->memc_mptpr = CONFIG_SYS_MPTPR ;
memctl->memc_mar = 0x00000088;
/* Map controller banks 1 to the SDRAM bank */
memctl->memc_or1 = CONFIG_SYS_OR1_PRELIM;
memctl->memc_br1 = CONFIG_SYS_BR1_PRELIM;
memctl->memc_mamr = CONFIG_SYS_MAMR_9COL & (~(MAMR_PTAE)); /* no refresh yet */
/*Disable Periodic timer A. */
udelay(200);
/* perform SDRAM initializsation sequence */
memctl->memc_mcr = 0x80002236; /* SDRAM bank 0 - refresh twice */
udelay(1);
memctl->memc_mamr |= MAMR_PTAE; /* enable refresh */
/*Enable Periodic timer A */
udelay (1000);
/* Check Bank 0 Memory Size
* try 9 column mode
*/
size9 = dram_size (CONFIG_SYS_MAMR_9COL, SDRAM_BASE_PRELIM, SDRAM_MAX_SIZE);
/*
* Final mapping:
*/
memctl->memc_or1 = ((-size9) & 0xFFFF0000) | CONFIG_SYS_OR_TIMING_SDRAM;
udelay (1000);
return (size9);
}
int board_early_init_f(void)
{
volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
volatile iop8xx_t *ioport = &immap->im_ioport;
volatile cpm8xx_t *cpm = &immap->im_cpm;
volatile memctl8xx_t *memctl = &immap->im_memctl;
(void)ioport;
(void)cpm;
#if 1
/* NAND chip select */
upmconfig(UPMB, (uint *) nandcs_table, sizeof(nandcs_table) / sizeof(nandcs_table[0]));
memctl->memc_or2 = ((0xFFFFFFFFLU & ~(NAND_SIZE - 1)) | OR_BI | OR_G5LS);
memctl->memc_br2 = ((NAND_BASE & BR_BA_MSK) | BR_PS_8 | BR_V | BR_MS_UPMB);
memctl->memc_mbmr = 0; /* all clear */
#endif
memctl->memc_br5 &= ~BR_V;
memctl->memc_br6 &= ~BR_V;
memctl->memc_br7 &= ~BR_V;
#if 1
ioport->iop_padat = PA_GP_OUTVAL;
ioport->iop_paodr = PA_ODR_VAL;
ioport->iop_padir = PA_GP_OUTMASK | PA_SP_DIRVAL;
ioport->iop_papar = PA_SP_MASK;
cpm->cp_pbdat = PB_GP_OUTVAL;
cpm->cp_pbodr = PB_ODR_VAL;
cpm->cp_pbdir = PB_GP_OUTMASK | PB_SP_DIRVAL;
cpm->cp_pbpar = PB_SP_MASK;
ioport->iop_pcdat = PC_GP_OUTVAL;
ioport->iop_pcdir = PC_GP_OUTMASK | PC_SP_DIRVAL;
ioport->iop_pcso = PC_SOVAL;
ioport->iop_pcint = PC_INTVAL;
ioport->iop_pcpar = PC_SP_MASK;
cpm->cp_pedat = PE_GP_OUTVAL;
cpm->cp_peodr = PE_ODR_VAL;
cpm->cp_pedir = PE_GP_OUTMASK | PE_SP_DIRVAL;
cpm->cp_pepar = PE_SP_MASK;
#endif
return 0;
}
phys_size_t initdram(int board_type)
{
volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
volatile memctl8xx_t *memctl = &immap->im_memctl;
long int size;
upmconfig(UPMA, (uint *) sdram_table, sizeof(sdram_table) / sizeof(uint));
/*
* Preliminary prescaler for refresh
*/
memctl->memc_mptpr = CONFIG_SYS_MPTPR_1BK_8K;
memctl->memc_mar = MAR_SDRAM_INIT; /* 32-bit address to be output on the address bus if AMX = 0b11 */
/*
* Map controller bank 3 to the SDRAM bank at preliminary address.
*/
memctl->memc_or3 = CONFIG_SYS_OR3_PRELIM;
memctl->memc_br3 = CONFIG_SYS_BR3_PRELIM;
memctl->memc_mamr = CONFIG_SYS_MAMR_9COL & ~MAMR_PTAE; /* no refresh yet */
udelay(200);
/* perform SDRAM initialisation sequence */
memctl->memc_mcr = MCR_OP_RUN | MCR_UM_UPMA | MCR_MB_CS3 | MCR_MCLF(1) | MCR_MAD(0x3C); /* precharge all */
udelay(1);
memctl->memc_mcr = MCR_OP_RUN | MCR_UM_UPMA | MCR_MB_CS3 | MCR_MCLF(0) | MCR_MAD(0x30); /* refresh 16 times(0) */
udelay(1);
memctl->memc_mcr = MCR_OP_RUN | MCR_UM_UPMA | MCR_MB_CS3 | MCR_MCLF(1) | MCR_MAD(0x3E); /* exception program (write mar) */
udelay(1);
memctl->memc_mamr |= MAMR_PTAE; /* enable refresh */
udelay(1000);
memctl->memc_mamr = CONFIG_SYS_MAMR_9COL;
size = SDRAM_MAX_SIZE;
udelay(10000);
return (size);
}
/*****************************************************************************
* Initialize DRAM controller
*****************************************************************************/
phys_size_t initdram (int board_type)
{
volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
volatile memctl8xx_t *memctl = &immap->im_memctl;
/*
* Only initialize memory controller when running from FLASH.
* When running from RAM, don't touch it.
*/
if ((ulong) initdram & 0xff000000) {
volatile uint *addr1, *addr2;
uint i;
upmconfig (UPMA, (uint *) edo_60ns_25MHz_tbl,
sizeof (edo_60ns_25MHz_tbl) / sizeof (uint));
memctl->memc_mptpr = 0x0200;
memctl->memc_mamr = 0x0ca20330;
memctl->memc_or2 = -CONFIG_SYS_DRAM_MAX | OR_CSNT_SAM;
memctl->memc_br2 = CONFIG_SYS_DRAM_BASE | BR_MS_UPMA | BR_V;
/*
* Do 8 read accesses to DRAM
*/
addr1 = (volatile uint *) 0;
addr2 = (volatile uint *) 0x00400000;
for (i = 0; i < 8; i++)
in_be32(addr1);
/*
* Now check whether we got 4MB or 16MB populated
*/
addr1[0] = 0x12345678;
addr1[1] = 0x9abcdef0;
addr2[0] = 0xfeedc0de;
addr2[1] = 0x47110815;
if (addr1[0] == 0xfeedc0de && addr1[1] == 0x47110815) {
/* only 4MB populated */
memctl->memc_or2 = -(CONFIG_SYS_DRAM_MAX / 4) | OR_CSNT_SAM;
}
}
return -(memctl->memc_or2 & 0xffff0000);
}
phys_size_t initdram (int board_type)
{
volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
volatile memctl8xx_t *memctl = &immap->im_memctl;
long int size10;
upmconfig (UPMA, (uint *) sdram_table,
sizeof (sdram_table) / sizeof (uint));
/* Refresh clock prescalar */
memctl->memc_mptpr = CONFIG_SYS_MPTPR;
memctl->memc_mar = 0x00000000;
/* Map controller banks 1 to the SDRAM bank */
memctl->memc_or1 = CONFIG_SYS_OR1_PRELIM;
memctl->memc_br1 = CONFIG_SYS_BR1_PRELIM;
memctl->memc_mamr = CONFIG_SYS_MAMR_10COL & (~(MAMR_PTAE)); /* no refresh yet */
udelay (200);
/* perform SDRAM initializsation sequence */
memctl->memc_mcr = 0x80002230; /* SDRAM bank 0 - refresh twice */
udelay (1);
memctl->memc_mamr |= MAMR_PTAE; /* enable refresh */
udelay (1000);
/* Check Bank 0 Memory Size
* try 10 column mode
*/
size10 = dram_size (CONFIG_SYS_MAMR_10COL, SDRAM_BASE_PRELIM,
SDRAM_MAX_SIZE);
return (size10);
}
int checkboard (void)
{
volatile ccsr_gur_t *gur = (void *)(CFG_MPC85xx_GUTS_ADDR);
char *src;
int f;
char *s = getenv("serial#");
puts("Board: Socrates");
if (s != NULL) {
puts(", serial# ");
puts(s);
}
putc('\n');
#ifdef CONFIG_PCI
/* Check the PCI_clk sel bit */
if (in_be32(&gur->porpllsr) & (1<<15)) {
src = "SYSCLK";
f = CONFIG_SYS_CLK_FREQ;
} else {
src = "PCI_CLK";
f = CONFIG_PCI_CLK_FREQ;
}
printf ("PCI1: 32 bit, %d MHz (%s)\n", f/1000000, src);
#else
printf ("PCI1: disabled\n");
#endif
/*
* Initialize local bus.
*/
local_bus_init ();
#if defined(CFG_FPGA_BASE)
/* Init UPMA for FPGA access */
upmconfig(UPMA, (uint *)UPMTableA, sizeof(UPMTableA)/sizeof(int));
#endif
return 0;
}
long int initdram (int board_type)
{
long int msize;
volatile immap_t *immap = (volatile immap_t *)CFG_IMMR;
volatile memctl8xx_t *memctl = &immap->im_memctl;
upmconfig(UPMA, sdram_table, sizeof(sdram_table) / sizeof(uint));
/* Configure SDRAM refresh */
memctl->memc_mptpr = MPTPR_PTP_DIV32; /* BRGCLK/32 */
memctl->memc_mamr = (94 << 24) | CFG_MAMR; /* No refresh */
udelay(200);
/* Run precharge from location 0x15 */
memctl->memc_mar = 0x0;
memctl->memc_mcr = 0x80002115;
udelay(200);
/* Run 8 refresh cycles */
memctl->memc_mcr = 0x80002830;
udelay(200);
/* Run MRS pattern from location 0x16 */
memctl->memc_mar = 0x88;
memctl->memc_mcr = 0x80002116;
udelay(200);
memctl->memc_mamr |= MAMR_PTAE; /* Enable refresh */
memctl->memc_or1 = ~(CFG_SDRAM_MAX_SIZE - 1) | OR_CSNT_SAM;
memctl->memc_br1 = CFG_SDRAM_BASE | BR_PS_32 | BR_MS_UPMA | BR_V;
msize = get_ram_size(CFG_SDRAM_BASE, CFG_SDRAM_MAX_SIZE);
memctl->memc_or1 |= ~(msize - 1);
return msize;
}
/*
* Miscellaneous intialization
*/
int misc_init_r (void)
{
volatile immap_t *immr = (immap_t *) CFG_IMMR;
volatile memctl8xx_t *memctl = &immr->im_memctl;
/*
* Set up UPMB to handle the Virtex FPGA SelectMap interface
*/
upmconfig (UPMB, (uint *) selectmap_upm_table,
sizeof (selectmap_upm_table) / sizeof (uint));
memctl->memc_mbmr = 0x0;
config_mpc8xx_ioports (immr);
#if (CONFIG_COMMANDS & CFG_CMD_MII)
mii_init ();
#endif
#if (CONFIG_FPGA)
gen860t_init_fpga ();
#endif
return 0;
}
long int initdram (int board_type)
{
volatile immap_t *immap = (immap_t *) CFG_IMMR;
volatile memctl8xx_t *memctl = &immap->im_memctl;
long int size_b0, size8, size9;
upmconfig (UPMA, (uint *) sdram_table,
sizeof (sdram_table) / sizeof (uint));
/*
* 1 Bank of 64Mbit x 2 devices
*/
memctl->memc_mptpr = CFG_MPTPR_1BK_4K;
memctl->memc_mar = 0x00000088;
/*
* Map controller SDRAM bank 0
*/
memctl->memc_or4 = CFG_OR4_PRELIM;
memctl->memc_br4 = CFG_BR4_PRELIM;
memctl->memc_mamr = CFG_MAMR_8COL & (~(MAMR_PTAE)); /* no refresh yet */
udelay (200);
/*
* Perform SDRAM initializsation sequence
*/
memctl->memc_mcr = 0x80008105; /* SDRAM bank 0 */
udelay (1);
memctl->memc_mamr = (CFG_MAMR_8COL & ~(MAMR_TLFA_MSK)) | MAMR_TLFA_8X;
udelay (200);
memctl->memc_mcr = 0x80008130; /* SDRAM bank 0 - execute twice */
udelay (1);
memctl->memc_mamr = (CFG_MAMR_8COL & ~(MAMR_TLFA_MSK)) | MAMR_TLFA_4X;
udelay (200);
memctl->memc_mamr |= MAMR_PTAE; /* enable refresh */
udelay (1000);
/*
* Preliminary prescaler for refresh (depends on number of
* banks): This value is selected for four cycles every 62.4 us
* with two SDRAM banks or four cycles every 31.2 us with one
* bank. It will be adjusted after memory sizing.
*/
memctl->memc_mptpr = CFG_MPTPR_2BK_4K; /* 16: but should be: CFG_MPTPR_1BK_4K */
/*
* Check Bank 0 Memory Size for re-configuration
*
* try 8 column mode
*/
size8 = dram_size (CFG_MAMR_8COL, (ulong *) SDRAM_BASE4_PRELIM,
SDRAM_MAX_SIZE);
udelay (1000);
/*
* try 9 column mode
*/
size9 = dram_size (CFG_MAMR_9COL, (ulong *) SDRAM_BASE4_PRELIM,
SDRAM_MAX_SIZE);
if (size8 < size9) { /* leave configuration at 9 columns */
size_b0 = size9;
/* debug ("SDRAM Bank 0 in 9 column mode: %ld MB\n", size >> 20); */
} else { /* back to 8 columns */
size_b0 = size8;
memctl->memc_mamr = CFG_MAMR_8COL;
udelay (500);
/* debug ("SDRAM Bank 0 in 8 column mode: %ld MB\n", size >> 20); */
}
udelay (1000);
/*
* Adjust refresh rate depending on SDRAM type, both banks
* For types > 128 MBit leave it at the current (fast) rate
*/
if ((size_b0 < 0x02000000)) {
/* reduce to 15.6 us (62.4 us / quad) */
memctl->memc_mptpr = CFG_MPTPR_2BK_4K;
udelay (1000);
}
/* SDRAM Bank 0 is bigger - map first */
memctl->memc_or4 = ((-size_b0) & 0xFFFF0000) | CFG_OR_TIMING_SDRAM;
memctl->memc_br4 = (CFG_SDRAM_BASE & BR_BA_MSK) | BR_MS_UPMA | BR_V;
udelay (10000);
return (size_b0);
}
phys_size_t initdram (int board_type)
{
volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
volatile memctl8xx_t *memctl = &immap->im_memctl;
long int size8, size9;
long int size_b0 = 0;
unsigned long reg;
upmconfig (UPMA, (uint *) sdram_table,
sizeof (sdram_table) / sizeof (uint));
/*
* Preliminary prescaler for refresh (depends on number of
* banks): This value is selected for four cycles every 62.4 us
* with two SDRAM banks or four cycles every 31.2 us with one
* bank. It will be adjusted after memory sizing.
*/
memctl->memc_mptpr = CONFIG_SYS_MPTPR_2BK_8K;
memctl->memc_mar = 0x00000088;
/*
* Map controller bank 2 to the SDRAM bank at
* preliminary address - these have to be modified after the
* SDRAM size has been determined.
*/
memctl->memc_or2 = CONFIG_SYS_OR2_PRELIM;
memctl->memc_br2 = CONFIG_SYS_BR2_PRELIM;
memctl->memc_mamr = CONFIG_SYS_MAMR_8COL & (~(MAMR_PTAE)); /* no refresh yet */
udelay (200);
/* perform SDRAM initializsation sequence */
memctl->memc_mcr = 0x80004105; /* SDRAM bank 0 */
udelay (200);
memctl->memc_mcr = 0x80004230; /* SDRAM bank 0 - execute twice */
udelay (200);
memctl->memc_mamr |= MAMR_PTAE; /* enable refresh */
udelay (1000);
/*
* Check Bank 2 Memory Size for re-configuration
*
* try 8 column mode
*/
size8 = dram_size (CONFIG_SYS_MAMR_8COL, (long *) SDRAM_BASE2_PRELIM,
SDRAM_MAX_SIZE);
udelay (1000);
/*
* try 9 column mode
*/
size9 = dram_size (CONFIG_SYS_MAMR_9COL, (long *) SDRAM_BASE2_PRELIM,
SDRAM_MAX_SIZE);
if (size8 < size9) { /* leave configuration at 9 columns */
size_b0 = size9;
/* debug ("SDRAM Bank 0 in 9 column mode: %ld MB\n", size >> 20); */
} else { /* back to 8 columns */
size_b0 = size8;
memctl->memc_mamr = CONFIG_SYS_MAMR_8COL;
udelay (500);
/* debug ("SDRAM Bank 0 in 8 column mode: %ld MB\n", size >> 20); */
}
udelay (1000);
/*
* Adjust refresh rate depending on SDRAM type, both banks
* For types > 128 MBit leave it at the current (fast) rate
*/
if ((size_b0 < 0x02000000)) {
/* reduce to 15.6 us (62.4 us / quad) */
memctl->memc_mptpr = CONFIG_SYS_MPTPR_2BK_4K;
udelay (1000);
}
/*
* Final mapping
*/
memctl->memc_or1 = ((-size_b0) & 0xFFFF0000) | CONFIG_SYS_OR_TIMING_SDRAM;
memctl->memc_br1 = (CONFIG_SYS_SDRAM_BASE & BR_BA_MSK) | BR_MS_UPMA | BR_V;
/* adjust refresh rate depending on SDRAM type, one bank */
reg = memctl->memc_mptpr;
reg >>= 1; /* reduce to CONFIG_SYS_MPTPR_1BK_8K / _4K */
memctl->memc_mptpr = reg;
udelay (10000);
#ifdef CONFIG_CAN_DRIVER
/* Initialize OR3 / BR3 */
memctl->memc_or3 = CONFIG_SYS_OR3_CAN; /* switch GPLB_5 to GPLA_5 */
memctl->memc_br3 = CONFIG_SYS_BR3_CAN;
/* Initialize MBMR */
memctl->memc_mbmr = MBMR_GPL_B4DIS; /* GPL_B4 works as UPWAITB */
/* Initialize UPMB for CAN: single read */
memctl->memc_mdr = 0xFFFFC004;
memctl->memc_mcr = 0x0100 | UPMB;
memctl->memc_mdr = 0x0FFFD004;
memctl->memc_mcr = 0x0101 | UPMB;
memctl->memc_mdr = 0x0FFFC000;
memctl->memc_mcr = 0x0102 | UPMB;
memctl->memc_mdr = 0x3FFFC004;
memctl->memc_mcr = 0x0103 | UPMB;
memctl->memc_mdr = 0xFFFFDC05;
memctl->memc_mcr = 0x0104 | UPMB;
/* Initialize UPMB for CAN: single write */
memctl->memc_mdr = 0xFFFCC004;
memctl->memc_mcr = 0x0118 | UPMB;
memctl->memc_mdr = 0xCFFCD004;
memctl->memc_mcr = 0x0119 | UPMB;
memctl->memc_mdr = 0x0FFCC000;
memctl->memc_mcr = 0x011A | UPMB;
memctl->memc_mdr = 0x7FFCC004;
memctl->memc_mcr = 0x011B | UPMB;
memctl->memc_mdr = 0xFFFDCC05;
memctl->memc_mcr = 0x011C | UPMB;
#endif
return (size_b0);
}
phys_size_t initdram(int board_type)
{
volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
volatile memctl8xx_t *memctl = &immap->im_memctl;
long int size;
upmconfig(UPMB, (uint *) sdram_table, sizeof(sdram_table) / sizeof(sdram_table[0]));
/*
* Preliminary prescaler for refresh
*/
memctl->memc_mptpr = MPTPR_PTP_DIV8;
memctl->memc_mar = MAR_SDRAM_INIT; /* 32-bit address to be output on the address bus if AMX = 0b11 */
/*
* Map controller bank 3 to the SDRAM bank at preliminary address.
*/
memctl->memc_or3 = CONFIG_SYS_OR3_PRELIM;
memctl->memc_br3 = CONFIG_SYS_BR3_PRELIM;
memctl->memc_mbmr = CONFIG_SYS_MAMR & ~MAMR_PTAE; /* no refresh yet */
udelay(200);
/* perform SDRAM initialisation sequence */
memctl->memc_mcr = MCR_OP_RUN | MCR_UPM_B | MCR_MB_CS3 | MCR_MLCF(1) | MCR_MAD(0x3C); /* precharge all */
udelay(1);
memctl->memc_mcr = MCR_OP_RUN | MCR_UPM_B | MCR_MB_CS3 | MCR_MLCF(2) | MCR_MAD(0x30); /* refresh 2 times(0) */
udelay(1);
memctl->memc_mcr = MCR_OP_RUN | MCR_UPM_B | MCR_MB_CS3 | MCR_MLCF(1) | MCR_MAD(0x3E); /* exception program (write mar)*/
udelay(1);
memctl->memc_mbmr |= MAMR_PTAE; /* enable refresh */
udelay(10000);
{
u32 d1, d2;
d1 = 0xAA55AA55;
*(volatile u32 *)0 = d1;
d2 = *(volatile u32 *)0;
if (d1 != d2) {
printf("DRAM fails: wrote 0x%08x read 0x%08x\n", d1, d2);
hang();
}
d1 = 0x55AA55AA;
*(volatile u32 *)0 = d1;
d2 = *(volatile u32 *)0;
if (d1 != d2) {
printf("DRAM fails: wrote 0x%08x read 0x%08x\n", d1, d2);
hang();
}
}
size = get_ram_size((long *)0, SDRAM_MAX_SIZE);
if (size == 0) {
printf("SIZE is zero: LOOP on 0\n");
for (;;) {
*(volatile u32 *)0 = 0;
(void)*(volatile u32 *)0;
}
}
return size;
}
phys_size_t initdram (int board_type)
{
volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
volatile memctl8xx_t *memctl = &immr->im_memctl;
/* volatile spc1920_pld_t *pld = (spc1920_pld_t *) CONFIG_SYS_SPC1920_PLD_BASE; */
long int size_b0;
long int size8, size9;
int i;
/*
* Configure UPMB for SDRAM
*/
upmconfig (UPMB, (uint *)sdram_table, sizeof(sdram_table)/sizeof(uint));
udelay(100);
memctl->memc_mptpr = CONFIG_SYS_MPTPR;
/* burst length=4, burst type=sequential, CAS latency=2 */
memctl->memc_mar = CONFIG_SYS_MAR;
/*
* Map controller bank 1 to the SDRAM bank at preliminary address.
*/
memctl->memc_or1 = CONFIG_SYS_OR1_PRELIM;
memctl->memc_br1 = CONFIG_SYS_BR1_PRELIM;
/* initialize memory address register */
memctl->memc_mbmr = CONFIG_SYS_MBMR_8COL; /* refresh not enabled yet */
/* mode initialization (offset 5) */
udelay (200); /* 0x80006105 */
memctl->memc_mcr = MCR_OP_RUN | MCR_UPM_B | MCR_MB_CS1 | MCR_MLCF (1) | MCR_MAD (0x05);
/* run 2 refresh sequence with 4-beat refresh burst (offset 0x30) */
udelay (1); /* 0x80006130 */
memctl->memc_mcr = MCR_OP_RUN | MCR_UPM_B | MCR_MB_CS1 | MCR_MLCF (1) | MCR_MAD (0x30);
udelay (1); /* 0x80006130 */
memctl->memc_mcr = MCR_OP_RUN | MCR_UPM_B | MCR_MB_CS1 | MCR_MLCF (1) | MCR_MAD (0x30);
udelay (1); /* 0x80006106 */
memctl->memc_mcr = MCR_OP_RUN | MCR_UPM_B | MCR_MB_CS1 | MCR_MLCF (1) | MCR_MAD (0x06);
memctl->memc_mbmr |= MBMR_PTBE; /* refresh enabled */
udelay (200);
/* Need at least 10 DRAM accesses to stabilize */
for (i = 0; i < 10; ++i) {
volatile unsigned long *addr =
(volatile unsigned long *) CONFIG_SYS_SDRAM_BASE;
unsigned long val;
val = *(addr + i);
*(addr + i) = val;
}
/*
* Check Bank 0 Memory Size for re-configuration
*
* try 8 column mode
*/
size8 = dram_size (CONFIG_SYS_MBMR_8COL, (long *)CONFIG_SYS_SDRAM_BASE, SDRAM_MAX_SIZE);
udelay (1000);
/*
* try 9 column mode
*/
size9 = dram_size (CONFIG_SYS_MBMR_9COL, (long *)CONFIG_SYS_SDRAM_BASE, SDRAM_MAX_SIZE);
if (size8 < size9) { /* leave configuration at 9 columns */
size_b0 = size9;
memctl->memc_mbmr = CONFIG_SYS_MBMR_9COL | MBMR_PTBE;
udelay (500);
} else { /* back to 8 columns */
size_b0 = size8;
memctl->memc_mbmr = CONFIG_SYS_MBMR_8COL | MBMR_PTBE;
udelay (500);
}
/*
* Final mapping:
*/
memctl->memc_or1 = ((-size_b0) & 0xFFFF0000) |
OR_CSNT_SAM | OR_G5LS | SDRAM_TIMING;
memctl->memc_br1 = (CONFIG_SYS_SDRAM_BASE & BR_BA_MSK) | BR_MS_UPMB | BR_V;
udelay (1000);
/* initalize the DSP Host Port Interface */
hpi_init();
/* FRAM Setup */
memctl->memc_or4 = CONFIG_SYS_OR4;
memctl->memc_br4 = CONFIG_SYS_BR4;
udelay(1000);
return (size_b0);
}
phys_size_t initdram (int board_type)
{
volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
volatile memctl8xx_t *memctl = &immap->im_memctl;
long int size;
upmconfig(UPMB, (uint *)sdram_table, sizeof(sdram_table)/sizeof(uint));
/*
* Prescaler for refresh
*/
memctl->memc_mptpr = 0x0400;
/*
* Map controller bank 2 to the SDRAM address
*/
memctl->memc_or2 = CONFIG_SYS_OR2;
memctl->memc_br2 = CONFIG_SYS_BR2;
udelay(200);
/* perform SDRAM initialization sequence */
memctl->memc_mbmr = CONFIG_SYS_16M_MBMR;
udelay(100);
memctl->memc_mar = 0x00000088;
memctl->memc_mcr = 0x80804105; /* run precharge pattern */
udelay(1);
/* Run two refresh cycles on SDRAM */
memctl->memc_mbmr = 0x18802118;
memctl->memc_mcr = 0x80804130;
memctl->memc_mbmr = 0x18802114;
memctl->memc_mcr = 0x80804106;
udelay (1000);
#if 0
/*
* Check for 64M SDRAM Memory Size
*/
size = dram_size (CONFIG_SYS_64M_MBMR, (ulong *)SDRAM_BASE, SDRAM_64M_MAX_SIZE);
udelay (1000);
/*
* Check for 16M SDRAM Memory Size
*/
if (size != SDRAM_64M_MAX_SIZE) {
#endif
size = dram_size (CONFIG_SYS_16M_MBMR, (long *)SDRAM_BASE, SDRAM_16M_MAX_SIZE);
udelay (1000);
#if 0
}
memctl->memc_or2 = ((-size) & 0xFFFF0000) | SDRAM_TIMING;
#endif
udelay(10000);
#if 0
/*
* Also, map other memory to correct position
*/
/*
* Map the 8M Intel Flash device to chip select 1
*/
memctl->memc_or1 = CONFIG_SYS_OR1;
memctl->memc_br1 = CONFIG_SYS_BR1;
/*
* Map 64K NVRAM, Sipex Device, NAND Ctl Reg, and LED Ctl Reg
* to chip select 3
*/
memctl->memc_or3 = CONFIG_SYS_OR3;
memctl->memc_br3 = CONFIG_SYS_BR3;
/*
* Map chip selects 4, 5, 6, & 7 for external expansion connector
*/
memctl->memc_or4 = CONFIG_SYS_OR4;
memctl->memc_br4 = CONFIG_SYS_BR4;
memctl->memc_or5 = CONFIG_SYS_OR5;
memctl->memc_br5 = CONFIG_SYS_BR5;
memctl->memc_or6 = CONFIG_SYS_OR6;
memctl->memc_br6 = CONFIG_SYS_BR6;
memctl->memc_or7 = CONFIG_SYS_OR7;
memctl->memc_br7 = CONFIG_SYS_BR7;
#endif
return (size);
}
long int initdram (int board_type)
{
volatile immap_t *immap = (immap_t *) CFG_IMMR;
volatile memctl8xx_t *memctl = &immap->im_memctl;
long int size8, size9;
long int size_b0 = 0;
/*
* This sequence initializes SDRAM chips on ELPT860 board
*/
upmconfig (UPMA, (uint *) init_sdram_table,
sizeof (init_sdram_table) / sizeof (uint));
memctl->memc_mptpr = 0x0200;
memctl->memc_mamr = 0x18002111;
memctl->memc_mar = 0x00000088;
memctl->memc_mcr = 0x80002000; /* CS1: SDRAM bank 0 */
upmconfig (UPMA, (uint *) sdram_table,
sizeof (sdram_table) / sizeof (uint));
/*
* Preliminary prescaler for refresh (depends on number of
* banks): This value is selected for four cycles every 62.4 us
* with two SDRAM banks or four cycles every 31.2 us with one
* bank. It will be adjusted after memory sizing.
*/
memctl->memc_mptpr = CFG_MPTPR_2BK_8K;
/*
* The following value is used as an address (i.e. opcode) for
* the LOAD MODE REGISTER COMMAND during SDRAM initialisation. If
* the port size is 32bit the SDRAM does NOT "see" the lower two
* address lines, i.e. mar=0x00000088 -> opcode=0x00000022 for
* MICRON SDRAMs:
* -> 0 00 010 0 010
* | | | | +- Burst Length = 4
* | | | +----- Burst Type = Sequential
* | | +------- CAS Latency = 2
* | +----------- Operating Mode = Standard
* +-------------- Write Burst Mode = Programmed Burst Length
*/
memctl->memc_mar = 0x00000088;
/*
* Map controller banks 2 and 3 to the SDRAM banks 2 and 3 at
* preliminary addresses - these have to be modified after the
* SDRAM size has been determined.
*/
memctl->memc_or1 = CFG_OR1_PRELIM;
memctl->memc_br1 = CFG_BR1_PRELIM;
memctl->memc_mamr = CFG_MAMR_8COL & (~(MAMR_PTAE)); /* no refresh yet */
udelay (200);
/* perform SDRAM initializsation sequence */
memctl->memc_mcr = 0x80002105; /* CS1: SDRAM bank 0 */
udelay (1);
memctl->memc_mcr = 0x80002230; /* CS1: SDRAM bank 0 - execute twice */
udelay (1);
memctl->memc_mamr |= MAMR_PTAE; /* enable refresh */
udelay (1000);
/*
* Check Bank 0 Memory Size for re-configuration
*
* try 8 column mode
*/
size8 = dram_size (CFG_MAMR_8COL,
(ulong *) SDRAM_BASE1_PRELIM, SDRAM_MAX_SIZE);
udelay (1000);
/*
* try 9 column mode
*/
size9 = dram_size (CFG_MAMR_9COL,
(ulong *) SDRAM_BASE1_PRELIM, SDRAM_MAX_SIZE);
if (size8 < size9) { /* leave configuration at 9 columns */
size_b0 = size9;
/* debug ("SDRAM Bank 0 in 9 column mode: %ld MB\n", size >> 20); */
} else { /* back to 8 columns */
size_b0 = size8;
memctl->memc_mamr = CFG_MAMR_8COL;
udelay (500);
/* debug ("SDRAM Bank 0 in 8 column mode: %ld MB\n", size >> 20); */
}
udelay (1000);
/*
* Adjust refresh rate depending on SDRAM type, both banks
* For types > 128 MBit leave it at the current (fast) rate
*/
if (size_b0 < 0x02000000) {
/* reduce to 15.6 us (62.4 us / quad) */
memctl->memc_mptpr = CFG_MPTPR_2BK_4K;
udelay (1000);
}
/*
* Final mapping: map bigger bank first
*/
memctl->memc_or1 = ((-size_b0) & 0xFFFF0000) | CFG_OR_TIMING_SDRAM;
memctl->memc_br1 = (CFG_SDRAM_BASE & BR_BA_MSK) | BR_MS_UPMA | BR_V;
{
unsigned long reg;
/* adjust refresh rate depending on SDRAM type, one bank */
reg = memctl->memc_mptpr;
reg >>= 1; /* reduce to CFG_MPTPR_1BK_8K / _4K */
memctl->memc_mptpr = reg;
}
udelay (10000);
return (size_b0);
}
int checkboard (void)
{
unsigned char *s, *e;
unsigned char buf[64];
int i;
i = getenv_r("serial#", buf, sizeof(buf));
s = (i>0) ? buf : NULL;
#ifdef CONFIG_QS850
if (!s || strncmp(s, "QS850", 5)) {
puts ("### No HW ID - assuming QS850");
#endif
#ifdef CONFIG_QS823
if (!s || strncmp(s, "QS823", 5)) {
puts ("### No HW ID - assuming QS823");
#endif
} else {
for (e=s; *e; ++e) {
if (*e == ' ')
break;
}
for ( ; s<e; ++s) {
putc (*s);
}
}
putc ('\n');
return (0);
}
/* ------------------------------------------------------------------------- */
/* SDRAM Mode Register Definitions */
/* Set SDRAM Burst Length to 4 (010) */
/* See Motorola MPC850 User Manual, Page 13-14 */
#define SDRAM_BURST_LENGTH (2)
/* Set Wrap Type to Sequential (0) */
/* See Motorola MPC850 User Manual, Page 13-14 */
#define SDRAM_WRAP_TYPE (0 << 3)
/* Set /CAS Latentcy to 2 clocks */
#define SDRAM_CAS_LATENTCY (2 << 4)
/* The Mode Register value must be shifted left by 2, since it is */
/* placed on the address bus, and the 2 LSBs are ignored for 32-bit accesses */
#define SDRAM_MODE_REG ((SDRAM_BURST_LENGTH|SDRAM_WRAP_TYPE|SDRAM_CAS_LATENTCY) << 2)
#define UPMA_RUN(loops,index) (0x80002000 + (loops<<8) + index)
/* Please note a value of zero = 16 loops */
#define REFRESH_INIT_LOOPS (0)
long int initdram (int board_type)
{
volatile immap_t *immap = (immap_t *)CFG_IMMR;
volatile memctl8xx_t *memctl = &immap->im_memctl;
long int size;
upmconfig(UPMA, (uint *)sdram_table, sizeof(sdram_table)/sizeof(uint));
/*
* Prescaler for refresh
*/
memctl->memc_mptpr = CFG_MPTPR;
/*
* Map controller bank 1 to the SDRAM address
*/
memctl->memc_or1 = CFG_OR1;
memctl->memc_br1 = CFG_BR1;
udelay(1000);
/* perform SDRAM initialization sequence */
memctl->memc_mamr = CFG_16M_MAMR;
udelay(100);
/* Program the SDRAM's Mode Register */
memctl->memc_mar = SDRAM_MODE_REG;
/* Run the Prechard Pattern at 0x3C */
memctl->memc_mcr = UPMA_RUN(1,0x3c);
udelay(1);
/* Run the Refresh program residing at MAD index 0x30 */
/* This contains the CBR Refresh command with a loop */
/* The SDRAM must be refreshed at least 2 times */
/* Please note a value of zero = 16 loops */
memctl->memc_mcr = UPMA_RUN(REFRESH_INIT_LOOPS,0x30);
udelay(1);
/* Run the Exception program residing at MAD index 0x3E */
/* This contains the Write Mode Register command */
/* The Write Mode Register command uses the value written to MAR */
memctl->memc_mcr = UPMA_RUN(1,0x3e);
udelay (1000);
/*
* Check for 32M SDRAM Memory Size
*/
size = dram_size(CFG_32M_MAMR|MAMR_PTAE,
(ulong *)SDRAM_BASE, SDRAM_32M_MAX_SIZE);
udelay (1000);
/*
* Check for 16M SDRAM Memory Size
*/
if (size != SDRAM_32M_MAX_SIZE) {
size = dram_size(CFG_16M_MAMR|MAMR_PTAE,
(ulong *)SDRAM_BASE, SDRAM_16M_MAX_SIZE);
udelay (1000);
}
udelay(10000);
return (size);
}
/* ------------------------------------------------------------------------- */
/*
* Check memory range for valid RAM. A simple memory test determines
* the actually available RAM size between addresses `base' and
* `base + maxsize'. Some (not all) hardware errors are detected:
* - short between address lines
* - short between data lines
*/
static long int dram_size (long int mamr_value, long int *base, long int maxsize)
{
volatile immap_t *immap = (immap_t *)CFG_IMMR;
volatile memctl8xx_t *memctl = &immap->im_memctl;
memctl->memc_mamr = mamr_value;
return (get_ram_size(base, maxsize));
}
long int initdram (int board_type)
{
volatile immap_t *immap = (immap_t *) CFG_IMMR;
volatile memctl8xx_t *memctl = &immap->im_memctl;
volatile iop8xx_t *iop = &immap->im_ioport;
volatile fec_t *fecp = &immap->im_cpm.cp_fec;
long int size;
upmconfig (UPMA, (uint *) sdram_table,
sizeof (sdram_table) / sizeof (uint));
/*
* Preliminary prescaler for refresh (depends on number of
* banks): This value is selected for four cycles every 62.4 us
* with two SDRAM banks or four cycles every 31.2 us with one
* bank. It will be adjusted after memory sizing.
*/
memctl->memc_mptpr = CFG_MPTPR;
memctl->memc_mar = 0x00000088;
/*
* Map controller banks 2 and 3 to the SDRAM banks 2 and 3 at
* preliminary addresses - these have to be modified after the
* SDRAM size has been determined.
*/
memctl->memc_or2 = CFG_OR2_PRELIM;
memctl->memc_br2 = CFG_BR2_PRELIM;
memctl->memc_mamr = CFG_MAMR & (~(MAMR_PTAE)); /* no refresh yet */
udelay (200);
/* perform SDRAM initializsation sequence */
memctl->memc_mcr = 0x80004105; /* SDRAM bank 0 */
udelay (1);
memctl->memc_mcr = 0x80004230; /* SDRAM bank 0 - execute twice */
udelay (1);
memctl->memc_mcr = 0x80004105; /* SDRAM precharge */
udelay (1);
memctl->memc_mcr = 0x80004030; /* SDRAM 16x autorefresh */
udelay (1);
memctl->memc_mcr = 0x80004138; /* SDRAM upload parameters */
udelay (1);
memctl->memc_mamr |= MAMR_PTAE; /* enable refresh */
udelay (1000);
/*
* Check Bank 0 Memory Size for re-configuration
*
*/
size = dram_size (CFG_MAMR, (ulong *) SDRAM_BASE_PRELIM,
SDRAM_MAX_SIZE);
udelay (1000);
memctl->memc_mamr = CFG_MAMR;
udelay (1000);
/*
* Final mapping
*/
memctl->memc_or2 = ((-size) & 0xFFFF0000) | CFG_OR2_PRELIM;
memctl->memc_br2 = ((CFG_SDRAM_BASE & BR_BA_MSK) | BR_MS_UPMA | BR_V);
udelay (10000);
/* prepare pin multiplexing for fast ethernet */
atmLoad ();
fecp->fec_ecntrl = 0x00000004; /* rev D3 pinmux SET */
iop->iop_pdpar |= 0x0080; /* set pin as MII_clock */
return (size);
}
ulong fpga_control (fpga_t* fpga, int cmd)
{
volatile immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
volatile memctl8xx_t *memctl = &immr->im_memctl;
switch (cmd) {
case FPGA_INIT_IS_HIGH:
immr->im_ioport.iop_pcdir &= ~fpga->init_mask; /* input */
return (immr->im_ioport.iop_pcdat & fpga->init_mask) ? 1:0;
case FPGA_INIT_SET_LOW:
immr->im_ioport.iop_pcdir |= fpga->init_mask; /* output */
immr->im_ioport.iop_pcdat &= ~fpga->init_mask;
break;
case FPGA_INIT_SET_HIGH:
immr->im_ioport.iop_pcdir |= fpga->init_mask; /* output */
immr->im_ioport.iop_pcdat |= fpga->init_mask;
break;
case FPGA_PROG_SET_LOW:
immr->im_ioport.iop_pcdat &= ~fpga->prog_mask;
break;
case FPGA_PROG_SET_HIGH:
immr->im_ioport.iop_pcdat |= fpga->prog_mask;
break;
case FPGA_DONE_IS_HIGH:
return (immr->im_ioport.iop_pcdat & fpga->done_mask) ? 1:0;
case FPGA_READ_MODE:
/* disable FPGA in memory controller */
memctl->memc_br4 = 0;
memctl->memc_or4 = PUMA_CONF_OR_READ;
memctl->memc_br4 = PUMA_CONF_BR_READ;
/* (re-) enable CAN drivers */
can_driver_enable ();
break;
case FPGA_LOAD_MODE:
/* disable FPGA in memory controller */
memctl->memc_br4 = 0;
/*
* We must disable the CAN drivers first because
* they use UPM B, too.
*/
can_driver_disable ();
/*
* Configure UPMB for FPGA
*/
upmconfig(UPMB,(uint *)puma_table,sizeof(puma_table)/sizeof(uint));
memctl->memc_or4 = PUMA_CONF_OR_LOAD;
memctl->memc_br4 = PUMA_CONF_BR_LOAD;
break;
case FPGA_GET_ID:
return *(volatile ulong *)fpga->conf_base;
case FPGA_INIT_PORTS:
immr->im_ioport.iop_pcpar &= ~fpga->init_mask; /* INIT I/O */
immr->im_ioport.iop_pcso &= ~fpga->init_mask;
immr->im_ioport.iop_pcdir &= ~fpga->init_mask;
immr->im_ioport.iop_pcpar &= ~fpga->prog_mask; /* PROG Output */
immr->im_ioport.iop_pcso &= ~fpga->prog_mask;
immr->im_ioport.iop_pcdir |= fpga->prog_mask;
immr->im_ioport.iop_pcpar &= ~fpga->done_mask; /* DONE Input */
immr->im_ioport.iop_pcso &= ~fpga->done_mask;
immr->im_ioport.iop_pcdir &= ~fpga->done_mask;
break;
}
return 0;
}
