void
V4LFrameSource::open() {
if (isOpen()) return;
if (m_deviceName.length() < 1) throw IOException("V4LFrameSource device not set");
if (m_width < 0 || m_height < 0) throw IOException("V4LFrameSource width or height invalid");
bool wasReset = usbReset();
for (int i = 0; i < 5 && m_fd < 0; i++) {
//m_fd = ::open(m_deviceName.c_str(), O_RDWR | O_NONBLOCK, 0);
m_fd = ::open(m_deviceName.c_str(), O_RDWR, 0);
if (m_fd < 0 && wasReset) {
sleep(1);
}
}
if (m_fd < 0) {
throw IOException("Failed to open v4l camera");
}
checkCapabilities();
updateCropping();
updateVideoFormat();
updateExposureTime(m_exposureTime);
updateStreamParameters(m_frameRate);
mmapBuffers();
}
// ==============================================================================
// - main
// ------------------------------------------------------------------------------
int main(void)
{
// ------------------------- Initialize Hardware
//PORTB: LEDs
DDRB = 0x0f;
PORTB = 0x00;
// PORTC: Buttons
DDRC = 0x00; // set all pins to input
PORTC = 0x0f; // pullups
// PORTD: 4066 control, interrupt, rx/tx, USB
DDRD = 0xf2;
// init UART
UCSR0B = ( 1 << UCSZ02);
UCSR0C = /*( 1 << UPM1) | */( 1 << UCSZ01) | ( 1 << UCSZ00 ); // Even Parity, 9 bit, 1 stop bit
UBRR0H = 0;
UBRR0L = 249; // 5000 baud (F_CPU/16/BAUD - 1)
// enable Pinchange Interrupt on PC5 -> PCINT13
PCICR = (1 << PCIE1);
PCMSK1 = (1 << PCINT13);
usbDeviceConnect();
usbReset();
usbInit();
wdt_enable(WDTO_1S); // enable watchdog timer
sei();
tx_state = idle_tx;
UCSR0B |= (1 << TXEN0); // turn on uart
select_cam(0);
unsigned long tt;
unsigned char idx;
// ------------------------- Main Loop
while(1) {
wdt_reset();
usbPoll(); // see if there's something going on on the usb bus
check_uart();
}
return 0;
}
// ==============================================================================
// - main
// ------------------------------------------------------------------------------
int main(void)
{
// ------------------------- Initialize Hardware
//PORTB: LEDs
DDRB = 0x0f;
PORTB = 0x00;
// PORTC: Buttons
DDRC = 0x00; // set all pins to input
PORTC = 0x0f; // pullups
// PORTD: 4066 control, interrupt, rx/tx, USB
DDRD = 0xf2;
// timer 0 -> millisecond clock
ticks = 0;
TCCR0A = (1 << WGM01); // CTC
TCCR0B = (0 << CS02) | (1 << CS01) | (0 << CS00); // 8 prescaler @ 20Mhz -> 2'500'000 Hz
TIMSK0 = (1 << OCIE0A); // enable interrupt
OCR0A = 249; // 10000 Hz -> 10 ticks / Millisecond
// init UART
UCSR0B = ( 1 << UCSZ02);
UCSR0C = /*( 1 << UPM1) | */( 1 << UCSZ01) | ( 1 << UCSZ00 ); // Even Parity, 9 bit, 1 stop bit
UBRR0H = 0;
UBRR0L = 249; // 5000 baud (F_CPU/16/BAUD - 1)
// enable Pinchange Interrupt on PC5 -> PCINT13
PCICR = (1 << PCIE1);
PCMSK1 = (1 << PCINT13);
usbDeviceConnect();
usbReset();
usbInit();
wdt_enable(WDTO_1S); // enable watchdog timer
sei();
tx_state = idle_tx;
UCSR0B |= (1 << TXEN0); // turn on uart
select_cam(0);
unsigned long tt;
unsigned char idx;
// ------------------------- Main Loop
while(1) {
wdt_reset();
usbPoll(); // see if there's something going on on the usb bus
check_uart();
if (millis()-lastTime >= 80) {
check_buttons();
}
}
return 0;
}
int main(void)
{
char just_detected = 1;
Gamepad *pad = NULL;
hardwareInit();
gcn64protocol_hwinit();
#ifdef WAIT_FOR_PAD
do {
pad = tryDetectController();
} while (pad == NULL);
curGamepad = pad;
#else
char i = 60;
do {
pad = tryDetectController();
if (pad) {
curGamepad = pad;
break;
}
_delay_ms(16);
} while (--i);
#endif
reconnect:
cli();
#ifdef SNES_MODE
if (curGamepad && curGamepad->reportDescriptor) {
rt_usbHidReportDescriptor = curGamepad->reportDescriptor;
rt_usbHidReportDescriptorSize = curGamepad->reportDescriptorSize;
} else {
rt_usbHidReportDescriptor = (void*)gcn64_usbHidReportDescriptor;
rt_usbHidReportDescriptorSize = getUsbHidReportDescriptor_size();
}
#else
rt_usbHidReportDescriptor = (void*)gcn64_usbHidReportDescriptor;
rt_usbHidReportDescriptorSize = getUsbHidReportDescriptor_size();
#endif
if (curGamepad && curGamepad->deviceDescriptor) {
rt_usbDeviceDescriptor = curGamepad->deviceDescriptor;
rt_usbDeviceDescriptorSize = curGamepad->deviceDescriptorSize;
} else {
rt_usbDeviceDescriptor = (void*)usbDescrDevice;
rt_usbDeviceDescriptorSize = getUsbDescrDevice_size();
}
// patch the config descriptor with the HID report descriptor size
my_usbDescriptorConfiguration[25] = rt_usbHidReportDescriptorSize;
my_usbDescriptorConfiguration[26] = rt_usbHidReportDescriptorSize >> 8;
// Do hardwareInit again. It causes a USB reset.
wdt_enable(WDTO_2S);
usbInit();
usbReset();
sei();
while (1)
{
usbPoll();
wdt_reset();
if ((curGamepad == NULL ))
{
//either no controller detected or we changed mode... lets try to redetect controller !
pad = tryDetectController();
if (pad) {
curGamepad = pad;
just_detected = 1;
/*if (pad->reportDescriptor != rt_usbHidReportDescriptor) {
goto reconnect;
}*/
}
else
{
curGamepad = NULL;
}
}
if (curGamepad != NULL) {
controller_present_doTasks(just_detected);
just_detected = 0;
}
}
return 0;
}
