Ejemplos de vm_dcl_config_pin_mode en C++ (Cpp)

Ejemplo n.º 1

Archivo: retarget.c Proyecto: xiongyihui/RePhone_with_CodeLite

void retarget_setup(void)
{
    VM_DCL_HANDLE uart_handle;
    vm_dcl_sio_control_dcb_t settings;

    if (retarget_device_handle != -1)
    {
        return;
    }

#if defined(__HDK_LINKIT_ONE_V1__)
        vm_dcl_config_pin_mode(VM_PIN_D0, VM_DCL_PIN_MODE_UART);
        vm_dcl_config_pin_mode(VM_PIN_D1, VM_DCL_PIN_MODE_UART);
#elif defined(__HDK_LINKIT_ASSIST_2502__)
        vm_dcl_config_pin_mode(VM_PIN_P8, VM_DCL_PIN_MODE_UART);
        vm_dcl_config_pin_mode(VM_PIN_P9, VM_DCL_PIN_MODE_UART);
#endif

    g_owner_id = vm_dcl_get_owner_id();
    uart_handle = vm_dcl_open(VM_DCL_SIO_UART_PORT1, g_owner_id);
    settings.owner_id = g_owner_id;
    settings.config.dsr_check = 0;
    settings.config.data_bits_per_char_length = VM_DCL_SIO_UART_BITS_PER_CHAR_LENGTH_8;
    settings.config.flow_control = VM_DCL_SIO_UART_FLOW_CONTROL_NONE;
    settings.config.parity = VM_DCL_SIO_UART_PARITY_NONE;
    settings.config.stop_bits = VM_DCL_SIO_UART_STOP_BITS_1;
    settings.config.baud_rate = VM_DCL_SIO_UART_BAUDRATE_115200;
    settings.config.sw_xoff_char = 0x13;
    settings.config.sw_xon_char = 0x11;
    vm_dcl_control(uart_handle, VM_DCL_SIO_COMMAND_SET_DCB_CONFIG, (void *)&settings);

    retarget_rx_signal_id = vm_signal_create();

    vm_dcl_register_callback(uart_handle,
                             VM_DCL_SIO_UART_READY_TO_READ,
                             (vm_dcl_callback)__retarget_irq_handler,
                             (void*)NULL);

    retarget_device_handle = uart_handle;
}

Ejemplo n.º 2

Archivo: settings.c Proyecto: MarxGonzalez/RePhone_Create_Kit_Source_Code

void lcd_backlight_level(VMUINT32 ulValue)
{
    VM_DCL_HANDLE pwm_handle;
    vm_dcl_pwm_set_clock_t pwm_clock;
    vm_dcl_pwm_set_counter_threshold_t pwm_config_adv;
    vm_dcl_config_pin_mode(3, VM_DCL_PIN_MODE_PWM);
    pwm_handle = vm_dcl_open(PIN2PWM(3), vm_dcl_get_owner_id());
    vm_dcl_control(pwm_handle, VM_PWM_CMD_START, 0);
    pwm_config_adv.counter = 100;
    pwm_config_adv.threshold = ulValue;
    pwm_clock.source_clock = 0;
    pwm_clock.source_clock_division = 3;
    vm_dcl_control(pwm_handle, VM_PWM_CMD_SET_CLOCK, (void *) (&pwm_clock));
    vm_dcl_control(pwm_handle, VM_PWM_CMD_SET_COUNTER_AND_THRESHOLD,
            (void *) (&pwm_config_adv));
    vm_dcl_close(pwm_handle);
}