/*! \fn void rngInit(void);
* \brief This function initializes the timer and watchdog
* \note Vars guaranteed to be initialized to 0 by avr libc
*/
void rngInit(void)
{
// Configure TIMER0 in normal mode, internal clock with no prescaler
TCCR0A = 0x00;
TCCR0B = 0x01;
ATOMIC_BLOCK(ATOMIC_RESTORESTATE)
{
// Enable 16ms interrupt
wdt_clear_flag();
wdt_change_enable();
wdt_enable_16ms_int();
}
}
/*! \fn main(void)
* \brief Main function
*/
int main(void)
{
uint16_t current_bootkey_val = eeprom_read_word((uint16_t*)EEP_BOOTKEY_ADDR);
RET_TYPE flash_init_result;
RET_TYPE touch_init_result;
RET_TYPE card_detect_ret;
uint8_t fuse_ok = TRUE;
// Disable JTAG to gain access to pins, set prescaler to 1 (fuses not set)
#ifndef PRODUCTION_KICKSTARTER_SETUP
disableJTAG();
CPU_PRESCALE(0);
#endif
// Check fuse settings: boot reset vector, 2k words, SPIEN, BOD 2.6V, programming & ver disabled
if ((boot_lock_fuse_bits_get(GET_LOW_FUSE_BITS) != 0xFF) || (boot_lock_fuse_bits_get(GET_HIGH_FUSE_BITS) != 0xD8) || (boot_lock_fuse_bits_get(GET_EXTENDED_FUSE_BITS) != 0xFB) || (boot_lock_fuse_bits_get(GET_LOCK_BITS) != 0xFC))
{
fuse_ok = FALSE;
}
// Check if PB5 is low to start electrical test
DDRB &= ~(1 << 5); PORTB |= (1 << 5);
smallForLoopBasedDelay();
if (!(PINB & (1 << 5)))
{
// Test result, true by default
uint8_t test_result = TRUE;
// Leave flash nS off
DDR_FLASH_nS |= (1 << PORTID_FLASH_nS);
PORT_FLASH_nS |= (1 << PORTID_FLASH_nS);
// Set PORTD as output, leave PORTID_OLED_SS high
DDRD |= 0xFF; PORTD |= 0xFF;
// All other pins are input by default, run our test
for (uint8_t i = 0; i < 4; i++)
{
PORTD |= 0xFF;
smallForLoopBasedDelay();
if (!(PINF & (0xC3)) || !(PINC & (1 << 6)) || !(PINE & (1 << 6)) || !(PINB & (1 << 4)))
{
test_result = FALSE;
}
PORTD &= (1 << PORTID_OLED_SS);
smallForLoopBasedDelay();
if ((PINF & (0xC3)) || (PINC & (1 << 6)) || (PINE & (1 << 6)) || (PINB & (1 << 4)))
{
test_result = FALSE;
}
}
// PB6 as test result output
DDRB |= (1 << 6);
// If test successful, light green LED
if ((test_result == TRUE) && (fuse_ok == TRUE))
{
PORTB |= (1 << 6);
}
else
{
PORTB &= ~(1 << 6);
}
while(1);
}
// This code will only be used for developers and beta testers
#if !defined(PRODUCTION_SETUP) && !defined(PRODUCTION_KICKSTARTER_SETUP)
// Check if we were reset and want to go to the bootloader
if (current_bootkey_val == BOOTLOADER_BOOTKEY)
{
// Disable WDT
wdt_reset();
wdt_clear_flag();
wdt_change_enable();
wdt_stop();
// Store correct bootkey
eeprom_write_word((uint16_t*)EEP_BOOTKEY_ADDR, CORRECT_BOOTKEY);
// Jump to bootloader
start_bootloader();
}
// Check if there was a change in the mooltipass setting storage to reset the parameters to their correct values
if (getMooltipassParameterInEeprom(USER_PARAM_INIT_KEY_PARAM) != USER_PARAM_CORRECT_INIT_KEY)
{
mooltipassParametersInit();
setMooltipassParameterInEeprom(USER_PARAM_INIT_KEY_PARAM, USER_PARAM_CORRECT_INIT_KEY);
}
#endif
// First time initializations for Eeprom (first boot at production or flash layout changes for beta testers)
if (current_bootkey_val != CORRECT_BOOTKEY)
{
// Erase Mooltipass parameters
mooltipassParametersInit();
// Set bootloader password bool to FALSE
eeprom_write_byte((uint8_t*)EEP_BOOT_PWD_SET, FALSE);
}
/* Check if a card is inserted in the Mooltipass to go to the bootloader */
#ifdef AVR_BOOTLOADER_PROGRAMMING
/* Disable JTAG to get access to the pins */
disableJTAG();
/* Init SMC port */
initPortSMC();
/* Delay for detection */
smallForLoopBasedDelay();
#if defined(HARDWARE_V1)
if (PIN_SC_DET & (1 << PORTID_SC_DET))
#elif defined(HARDWARE_OLIVIER_V1)
if (!(PIN_SC_DET & (1 << PORTID_SC_DET)))
#endif
{
uint16_t tempuint16;
/* What follows is a copy from firstDetectFunctionSMC() */
/* Enable power to the card */
PORT_SC_POW &= ~(1 << PORTID_SC_POW);
/* Default state: PGM to 0 and RST to 1 */
PORT_SC_PGM &= ~(1 << PORTID_SC_PGM);
DDR_SC_PGM |= (1 << PORTID_SC_PGM);
PORT_SC_RST |= (1 << PORTID_SC_RST);
DDR_SC_RST |= (1 << PORTID_SC_RST);
/* Activate SPI port */
PORT_SPI_NATIVE &= ~((1 << SCK_SPI_NATIVE) | (1 << MOSI_SPI_NATIVE));
DDRB |= (1 << SCK_SPI_NATIVE) | (1 << MOSI_SPI_NATIVE);
setSPIModeSMC();
/* Let the card come online */
smallForLoopBasedDelay();
/* Check smart card FZ */
readFabricationZone((uint8_t*)&tempuint16);
if ((swap16(tempuint16)) != SMARTCARD_FABRICATION_ZONE)
{
removeFunctionSMC();
start_bootloader();
}
else
{
removeFunctionSMC();
}
}
#endif
initPortSMC(); // Initialize smart card port
initPwm(); // Initialize PWM controller
initIRQ(); // Initialize interrupts
powerSettlingDelay(); // Let the power settle
initUsb(); // Initialize USB controller
powerSettlingDelay(); // Let the USB 3.3V LDO rise
initI2cPort(); // Initialize I2C interface
rngInit(); // Initialize avrentropy library
oledInitIOs(); // Initialize OLED input/outputs
spiUsartBegin(SPI_RATE_8_MHZ); // Start USART SPI at 8MHz
// If offline mode isn't enabled, wait for device to be enumerated
if (getMooltipassParameterInEeprom(OFFLINE_MODE_PARAM) == FALSE)
{
while(!isUsbConfigured()); // Wait for host to set configuration
}
// Set correct timeout_enabled val
mp_timeout_enabled = getMooltipassParameterInEeprom(LOCK_TIMEOUT_ENABLE_PARAM);
// Launch the before flash initialization tests
#ifdef TESTS_ENABLED
beforeFlashInitTests();
#endif
// Check if we can initialize the Flash memory
flash_init_result = initFlash();
// Launch the after flash initialization tests
#ifdef TESTS_ENABLED
afterFlashInitTests();
#endif
// Set up OLED now that USB is receiving full 500mA.
oledBegin(FONT_DEFAULT);
// First time initializations for Flash (first time power up at production)
if (current_bootkey_val != CORRECT_BOOTKEY)
{
// Erase everything non graphic in flash
eraseFlashUsersContents();
// Erase # of cards and # of users
firstTimeUserHandlingInit();
}
// Check if we can initialize the touch sensing element
touch_init_result = initTouchSensing();
// Enable proximity detection
#ifndef HARDWARE_V1
activateProxDetection();
#endif
// Launch the after touch initialization tests
#ifdef TESTS_ENABLED
afterTouchInitTests();
#endif
// Test procedure to check that all HW is working
#if defined(PRODUCTION_SETUP) || defined(PRODUCTION_KICKSTARTER_SETUP)
if (current_bootkey_val != CORRECT_BOOTKEY)
{
RET_TYPE temp_rettype;
// Wait for USB host to upload bundle, which then sets USER_PARAM_INIT_KEY_PARAM
//#ifdef PRODUCTION_KICKSTARTER_SETUP
while(getMooltipassParameterInEeprom(USER_PARAM_INIT_KEY_PARAM) != 0xF1)
{
usbProcessIncoming(USB_CALLER_MAIN);
}
//#endif
// Bundle uploaded, start the screen
oledBegin(FONT_DEFAULT);
oledWriteActiveBuffer();
oledSetXY(0,0);
// LEDs ON, to check
setPwmDc(MAX_PWM_VAL);
switchOnButtonWheelLeds();
guiDisplayRawString(ID_STRING_TEST_LEDS_CH);
// Check flash init
if (flash_init_result != RETURN_OK)
{
guiDisplayRawString(ID_STRING_TEST_FLASH_PB);
}
// Check touch init
if (touch_init_result != RETURN_OK)
{
guiDisplayRawString(ID_STRING_TEST_TOUCH_PB);
}
// Touch instructions
guiDisplayRawString(ID_STRING_TEST_INST_TCH);
// Check prox
while(!(touchDetectionRoutine(0) & RETURN_PROX_DETECTION));
guiDisplayRawString(ID_STRING_TEST_DET);
activateGuardKey();
// Check left
while(!(touchDetectionRoutine(0) & RETURN_LEFT_PRESSED));
guiDisplayRawString(ID_STRING_TEST_LEFT);
// Check wheel
while(!(touchDetectionRoutine(0) & RETURN_WHEEL_PRESSED));
guiDisplayRawString(ID_STRING_TEST_WHEEL);
// Check right
while(!(touchDetectionRoutine(0) & RETURN_RIGHT_PRESSED));
guiDisplayRawString(ID_STRING_TEST_RIGHT);
// Insert card
guiDisplayRawString(ID_STRING_TEST_CARD_INS);
while(isCardPlugged() != RETURN_JDETECT);
temp_rettype = cardDetectedRoutine();
// Check card
if (!((temp_rettype == RETURN_MOOLTIPASS_BLANK) || (temp_rettype == RETURN_MOOLTIPASS_USER)))
{
guiDisplayRawString(ID_STRING_TEST_CARD_PB);
}
// Display result
uint8_t script_return = RETURN_OK;
if ((flash_init_result == RETURN_OK) && (touch_init_result == RETURN_OK) && ((temp_rettype == RETURN_MOOLTIPASS_BLANK) || (temp_rettype == RETURN_MOOLTIPASS_USER)))
{
// Inform script of success
usbSendMessage(CMD_FUNCTIONAL_TEST_RES, 1, &script_return);
// Wait for password to be set
while(eeprom_read_byte((uint8_t*)EEP_BOOT_PWD_SET) != BOOTLOADER_PWDOK_KEY)
{
usbProcessIncoming(USB_CALLER_MAIN);
}
// Display test result
guiDisplayRawString(ID_STRING_TEST_OK);
timerBasedDelayMs(3000);
}
else
{
// Set correct bool
script_return = RETURN_NOK;
// Display test result
guiDisplayRawString(ID_STRING_TEST_NOK);
// Inform script of failure
usbSendMessage(CMD_FUNCTIONAL_TEST_RES, 1, &script_return);
while(1)
{
usbProcessIncoming(USB_CALLER_MAIN);
}
}
}
#endif
// Stop the Mooltipass if we can't communicate with the flash or the touch interface
#if defined(HARDWARE_OLIVIER_V1)
#ifdef PRODUCTION_KICKSTARTER_SETUP
while ((flash_init_result != RETURN_OK) || (touch_init_result != RETURN_OK) || (fuse_ok != TRUE));
#else
while ((flash_init_result != RETURN_OK) || (touch_init_result != RETURN_OK));
#endif
#endif
// First time initializations done.... write correct value in eeprom
if (current_bootkey_val != CORRECT_BOOTKEY)
{
// Store correct bootkey
eeprom_write_word((uint16_t*)EEP_BOOTKEY_ADDR, CORRECT_BOOTKEY);
}
// Write inactive buffer & go to startup screen
oledWriteInactiveBuffer();
guiSetCurrentScreen(SCREEN_DEFAULT_NINSERTED);
guiGetBackToCurrentScreen();
// Launch the after HaD logo display tests
#ifdef TESTS_ENABLED
afterHadLogoDisplayTests();
#endif
// Let's fade in the LEDs
for (uint16_t i = 0; i < MAX_PWM_VAL; i++)
{
setPwmDc(i);
timerBasedDelayMs(0);
}
activityDetectedRoutine();
launchCalibrationCycle();
touchClearCurrentDetections();
// Inhibit touch inputs for the first 3 seconds
activateTimer(TIMER_TOUCH_INHIBIT, 3000);
while (1)
{
// Process possible incoming USB packets
usbProcessIncoming(USB_CALLER_MAIN);
// Call GUI routine once the touch input inhibit timer is finished
if (hasTimerExpired(TIMER_TOUCH_INHIBIT, FALSE) == TIMER_EXPIRED)
{
guiMainLoop();
}
// Check if a card just got inserted / removed
card_detect_ret = isCardPlugged();
// Do appropriate actions on smartcard insertion / removal
if (card_detect_ret == RETURN_JDETECT)
{
// Light up the Mooltipass and call the dedicated function
activityDetectedRoutine();
handleSmartcardInserted();
}
else if (card_detect_ret == RETURN_JRELEASED)
{
// Light up the Mooltipass and call the dedicated function
activityDetectedRoutine();
handleSmartcardRemoved();
// Set correct screen
guiDisplayInformationOnScreen(ID_STRING_CARD_REMOVED);
guiSetCurrentScreen(SCREEN_DEFAULT_NINSERTED);
userViewDelay();
guiGetBackToCurrentScreen();
}
// Two quick caps lock presses wakes up the device
if ((hasTimerExpired(TIMER_CAPS, FALSE) == TIMER_EXPIRED) && (getKeyboardLeds() & HID_CAPS_MASK) && (wasCapsLockTimerArmed == FALSE))
{
wasCapsLockTimerArmed = TRUE;
activateTimer(TIMER_CAPS, CAPS_LOCK_DEL);
}
else if ((hasTimerExpired(TIMER_CAPS, FALSE) == TIMER_RUNNING) && !(getKeyboardLeds() & HID_CAPS_MASK))
{
activityDetectedRoutine();
}
else if ((hasTimerExpired(TIMER_CAPS, FALSE) == TIMER_EXPIRED) && !(getKeyboardLeds() & HID_CAPS_MASK))
{
wasCapsLockTimerArmed = FALSE;
}
// If we have a timeout lock
if ((mp_timeout_enabled == TRUE) && (hasTimerExpired(SLOW_TIMER_LOCKOUT, TRUE) == TIMER_EXPIRED))
{
guiSetCurrentScreen(SCREEN_DEFAULT_INSERTED_LCK);
guiGetBackToCurrentScreen();
handleSmartcardRemoved();
}
}
}
/*! \fn main(void)
* \brief Main function
* \note For our security chain to be valid, EEP_BOOT_PWD_SET in eeprom needs to be set to BOOTLOADER_PWDOK_KEY
*/
int main(void)
{
/* Fetch bootkey in eeprom */
uint16_t current_bootkey_val = eeprom_read_word((uint16_t*)EEP_BOOTKEY_ADDR); // Bootkey in EEPROM
uint8_t new_aes_key[AES_KEY_LENGTH/8]; // New AES encryption key
uint8_t cur_aes_key[AES_KEY_LENGTH/8]; // AES encryption key
uint8_t firmware_data[SPM_PAGESIZE]; // One page of firmware data
aes256_context temp_aes_context; // AES context
uint8_t cur_cbc_mac[16]; // Current CBCMAC val
uint8_t temp_data[16]; // Temporary 16 bytes array
RET_TYPE flash_init_result; // Flash initialization result
uint16_t firmware_start_address = UINT16_MAX - MAX_FIRMWARE_SIZE - sizeof(cur_cbc_mac) - sizeof(cur_aes_key) + 1; // Start address of firmware in external memory
uint16_t firmware_end_address = UINT16_MAX - sizeof(cur_cbc_mac) - sizeof(cur_aes_key) + 1; // End address of firmware in external memory
/* Just in case we are going to disable the watch dog timer and disable interrupts */
cli();
wdt_reset();
wdt_clear_flag();
wdt_change_enable();
wdt_stop();
/* Check fuses: 2k words, SPIEN, BOD 4.3V, BOOTRST programming & ver disabled >> http://www.engbedded.com/fusecalc/ */
if ((boot_lock_fuse_bits_get(GET_LOW_FUSE_BITS) != 0xFF) || (boot_lock_fuse_bits_get(GET_HIGH_FUSE_BITS) != 0xD8) || (boot_lock_fuse_bits_get(GET_EXTENDED_FUSE_BITS) != 0xF8) || (boot_lock_fuse_bits_get(GET_LOCK_BITS) != 0xFC))
{
while(1);
}
/* If security isn't set in place yet, no point in launching the bootloader */
if (eeprom_read_byte((uint8_t*)EEP_BOOT_PWD_SET) != BOOTLOADER_PWDOK_KEY)
{
start_firmware();
}
/* Check if the device is booting normally, if the bootloader was called, or unknown state */
if (current_bootkey_val == CORRECT_BOOTKEY)
{
/* Security system set, correct bootkey for firmware */
start_firmware();
}
else if (current_bootkey_val != BOOTLOADER_BOOTKEY)
{
/* Security system set, bootkey isn't the bootloader one nor the main fw one... */
while(1);
}
/* By default, brick the device so it's an all or nothing update procedure */
eeprom_write_word((uint16_t*)EEP_BOOTKEY_ADDR, BRICKED_BOOTKEY);
/* Init IOs */
UHWCON = 0x01; // Enable USB 3.3V LDO
initFlashIOs(); // Init EXT Flash IOs
spiUsartBegin(); // Init SPI Controller
DDR_ACC_SS |= (1 << PORTID_ACC_SS); // Setup PORT for the Accelerometer SS
PORT_ACC_SS |= (1 << PORTID_ACC_SS); // Setup PORT for the Accelerometer SS
DDR_OLED_SS |= (1 << PORTID_OLED_SS); // Setup PORT for the OLED SS
PORT_OLED_SS |= (1 << PORTID_OLED_SS); // Setup PORT for the OLED SS
for (uint16_t i = 0; i < 20000; i++) asm volatile ("NOP");
/* Disable I2C block of the Accelerometer */
PORT_ACC_SS &= ~(1 << PORTID_ACC_SS);
spiUsartTransfer(0x23);
spiUsartTransfer(0x02);
PORT_ACC_SS |= (1 << PORTID_ACC_SS);
/* Check Flash */
flash_init_result = checkFlashID();
if (flash_init_result != RETURN_OK)
{
while(1);
}
for (uint8_t pass_number = 0; pass_number < 2; pass_number++)
{
/* Init CBCMAC encryption context*/
eeprom_read_block((void*)cur_aes_key, (void*)EEP_BOOT_PWD, sizeof(cur_aes_key));
memset((void*)cur_cbc_mac, 0x00, sizeof(cur_cbc_mac));
memset((void*)temp_data, 0x00, sizeof(temp_data));
aes256_init_ecb(&temp_aes_context, cur_aes_key);
// Compute CBCMAC for between the start of the graphics zone until the max addressing space (65536) - the size of the CBCMAC
for (uint16_t i = GRAPHIC_ZONE_START; i < (UINT16_MAX - sizeof(cur_cbc_mac) + 1); i += sizeof(cur_cbc_mac))
{
// Read data from external flash
flashRawRead(temp_data, i, sizeof(temp_data));
// If we got to the part containing to firmware
if ((i >= firmware_start_address) && (i < firmware_end_address))
{
// Append firmware data to current buffer
uint16_t firmware_data_address = i - firmware_start_address;
memcpy(firmware_data + (firmware_data_address & SPM_PAGE_SIZE_BYTES_BM), temp_data, sizeof(temp_data));
// If we have a full page in buffer, flash it
firmware_data_address += sizeof(cur_cbc_mac);
if (((firmware_data_address & SPM_PAGE_SIZE_BYTES_BM) == 0x0000) && (pass_number == 1))
{
boot_program_page(firmware_data_address - SPM_PAGESIZE, firmware_data);
}
}
// If we got to the part containing the encrypted new aes key (end of the for())
if (i >= firmware_end_address)
{
memcpy(new_aes_key + i - firmware_end_address, temp_data, sizeof(temp_data));
}
// Continue computation of CBCMAC
aesXorVectors(cur_cbc_mac, temp_data, sizeof(temp_data));
aes256_encrypt_ecb(&temp_aes_context, cur_cbc_mac);
}
// Read CBCMAC in memory and compare it with the computed value
flashRawRead(temp_data, (UINT16_MAX - sizeof(cur_cbc_mac) + 1), sizeof(cur_cbc_mac));
if (pass_number == 0)
{
// First pass, compare CBCMAC and see if we do the next pass or start the firmware
if (sideChannelSafeMemCmp(temp_data, cur_cbc_mac, sizeof(cur_cbc_mac)) != 0)
{
// No match, start the main firmware
eeprom_write_word((uint16_t*)EEP_BOOTKEY_ADDR, CORRECT_BOOTKEY);
start_firmware();
}
else
{
// Otherwise, next pass!
}
}
else
{
// Second pass, compare CBCMAC and then update AES keys
if (sideChannelSafeMemCmp(temp_data, cur_cbc_mac, sizeof(cur_cbc_mac)) == 0)
{
// Fetch the encrypted new aes key from flash, decrypt it, store it
aes256_decrypt_ecb(&temp_aes_context, new_aes_key);
aes256_decrypt_ecb(&temp_aes_context, new_aes_key+16);
eeprom_write_block((void*)new_aes_key, (void*)EEP_BOOT_PWD, sizeof(new_aes_key));
eeprom_write_word((uint16_t*)EEP_BOOTKEY_ADDR, CORRECT_BOOTKEY);
start_firmware();
}
else
{
// Fail, erase everything! >> maybe just write a while(1) in the future?
for (uint16_t i = 0; i < MAX_FIRMWARE_SIZE; i += SPM_PAGESIZE)
{
boot_page_erase(i);
boot_spm_busy_wait();
}
while(1);
}
}
}
}
/*! \fn usbProcessIncoming(uint8_t* incomingData)
* \brief Process the incoming USB packet
* \param incomingData Pointer to the packet (can be overwritten!)
*/
void usbProcessIncoming(uint8_t* incomingData)
{
// Temp plugin return value
uint8_t plugin_return_value = PLUGIN_BYTE_ERROR;
// Use message structure
usbMsg_t* msg = (usbMsg_t*)incomingData;
// Get data len
uint8_t datalen = msg->len;
// Get data cmd
uint8_t datacmd = msg->cmd;
#ifdef USB_FEATURE_PLUGIN_COMMS
// Temp ret_type
RET_TYPE temp_rettype;
#endif
#ifdef DEV_PLUGIN_COMMS
char stack_str[10];
#endif
// Debug comms
// USBDEBUGPRINTF_P(PSTR("usb: rx cmd 0x%02x len %u\n"), datacmd, datalen);
switch(datacmd)
{
// ping command
case CMD_PING :
{
usbSendMessage(0, 6, msg);
return;
}
// version command
case CMD_VERSION :
{
msg->len = 3; // len + cmd + FLASH_CHIP
msg->cmd = CMD_VERSION;
msg->body.data[0] = FLASH_CHIP;
msg->len += getVersion((char*)&msg->body.data[1], sizeof(msg->body.data) - 1);
usbSendMessage(0, msg->len, msg);
return;
}
#ifdef USB_FEATURE_PLUGIN_COMMS
// context command
case CMD_CONTEXT :
{
if (checkTextField(msg->body.data, datalen, NODE_PARENT_SIZE_OF_SERVICE) == RETURN_NOK)
{
plugin_return_value = PLUGIN_BYTE_ERROR;
USBPARSERDEBUGPRINTF_P(PSTR("setCtx: len %d too big\n"), datalen);
}
else if (getSmartCardInsertedUnlocked() != TRUE)
{
plugin_return_value = PLUGIN_BYTE_NOCARD;
USBPARSERDEBUGPRINTF_P(PSTR("set context: no card\n"));
}
else if (setCurrentContext(msg->body.data, datalen) == RETURN_OK)
{
plugin_return_value = PLUGIN_BYTE_OK;
USBPARSERDEBUGPRINTF_P(PSTR("set context: \"%s\" ok\n"), msg->body.data);
}
else
{
plugin_return_value = PLUGIN_BYTE_ERROR;
USBPARSERDEBUGPRINTF_P(PSTR("set context: \"%s\" failed\n"), msg->body.data);
}
break;
}
// get login
case CMD_GET_LOGIN :
{
if (getLoginForContext((char*)incomingData) == RETURN_OK)
{
// Use the buffer to store the login...
usbSendMessage(CMD_GET_LOGIN, strlen((char*)incomingData)+1, incomingData);
USBPARSERDEBUGPRINTF_P(PSTR("get login: \"%s\"\n"),(char *)incomingData);
return;
}
else
{
plugin_return_value = PLUGIN_BYTE_ERROR;
USBPARSERDEBUGPRINTF_P(PSTR("get login: failed\n"));
}
break;
}
// get password
case CMD_GET_PASSWORD :
{
if (getPasswordForContext((char*)incomingData) == RETURN_OK)
{
usbSendMessage(CMD_GET_PASSWORD, strlen((char*)incomingData)+1, incomingData);
USBPARSERDEBUGPRINTF_P(PSTR("get pass: \"%s\"\n"),(char *)incomingData);
return;
}
else
{
plugin_return_value = PLUGIN_BYTE_ERROR;
USBPARSERDEBUGPRINTF_P(PSTR("get pass: failed\n"));
}
break;
}
// set login
case CMD_SET_LOGIN :
{
if (checkTextField(msg->body.data, datalen, NODE_CHILD_SIZE_OF_LOGIN) == RETURN_NOK)
{
plugin_return_value = PLUGIN_BYTE_ERROR;
USBPARSERDEBUGPRINTF_P(PSTR("set login: \"%s\" checkTextField failed\n"),msg->body.data);
}
else if (setLoginForContext(msg->body.data, datalen) == RETURN_OK)
{
plugin_return_value = PLUGIN_BYTE_OK;
USBPARSERDEBUGPRINTF_P(PSTR("set login: \"%s\" ok\n"),msg->body.data);
}
else
{
plugin_return_value = PLUGIN_BYTE_ERROR;
USBPARSERDEBUGPRINTF_P(PSTR("set login: \"%s\" failed\n"),msg->body.data);
}
break;
}
// set password
case CMD_SET_PASSWORD :
{
if (checkTextField(msg->body.data, datalen, NODE_CHILD_SIZE_OF_PASSWORD) == RETURN_NOK)
{
plugin_return_value = PLUGIN_BYTE_ERROR;
USBPARSERDEBUGPRINTF_P(PSTR("set pass: len %d invalid\n"), datalen);
}
else if (setPasswordForContext(msg->body.data, datalen) == RETURN_OK)
{
plugin_return_value = PLUGIN_BYTE_OK;
USBPARSERDEBUGPRINTF_P(PSTR("set pass: \"%s\" ok\n"),msg->body.data);
}
else
{
plugin_return_value = PLUGIN_BYTE_ERROR;
USBPARSERDEBUGPRINTF_P(PSTR("set pass: failed\n"));
}
break;
}
// check password
case CMD_CHECK_PASSWORD :
{
if (checkTextField(msg->body.data, datalen, NODE_CHILD_SIZE_OF_PASSWORD) == RETURN_NOK)
{
plugin_return_value = PLUGIN_BYTE_ERROR;
break;
}
temp_rettype = checkPasswordForContext(msg->body.data, datalen);
if (temp_rettype == RETURN_PASS_CHECK_NOK)
{
plugin_return_value = PLUGIN_BYTE_ERROR;
}
else if(temp_rettype == RETURN_PASS_CHECK_OK)
{
plugin_return_value = PLUGIN_BYTE_OK;
}
else
{
plugin_return_value = PLUGIN_BYTE_NA;
}
break;
}
// set password
case CMD_ADD_CONTEXT :
{
if (checkTextField(msg->body.data, datalen, NODE_PARENT_SIZE_OF_SERVICE) == RETURN_NOK)
{
// Check field
plugin_return_value = PLUGIN_BYTE_ERROR;
USBPARSERDEBUGPRINTF_P(PSTR("set context: len %d invalid\n"), datalen);
}
else if (addNewContext(msg->body.data, datalen) == RETURN_OK)
{
// We managed to add a new context
plugin_return_value = PLUGIN_BYTE_OK;
USBPARSERDEBUGPRINTF_P(PSTR("add context: \"%s\" ok\n"),msg->body.data);
}
else
{
// Couldn't add a new context
plugin_return_value = PLUGIN_BYTE_ERROR;
USBPARSERDEBUGPRINTF_P(PSTR("add context: \"%s\" failed\n"),msg->body.data);
}
break;
}
#endif
#ifdef FLASH_BLOCK_IMPORT_EXPORT
// flash export start
case CMD_EXPORT_FLASH_START :
{
approveImportExportMemoryOperation(CMD_EXPORT_FLASH_START, &plugin_return_value);
guiGetBackToCurrentScreen();
break;
}
// export flash contents
case CMD_EXPORT_FLASH :
{
uint8_t size = PACKET_EXPORT_SIZE;
// Check that the user approved
if (currentFlashOpUid != CMD_EXPORT_FLASH_START)
{
return;
}
//flashOpCurAddr1 is the page
//flashOpCurAddr2 is the offset
// Check if the export address is correct
if (flashOpCurAddr1 >= PAGE_COUNT)
{
usbSendMessage(CMD_EXPORT_FLASH_END, 0, NULL);
USBPARSERDEBUGPRINTF_P(PSTR("export: end\n"));
currentFlashOpUid = 0;
return;
}
// Check how much data we need in case we're close to the page end
if ((BYTES_PER_PAGE - flashOpCurAddr2) < PACKET_EXPORT_SIZE)
{
size = (uint8_t)(BYTES_PER_PAGE - flashOpCurAddr2);
}
// Get a block of data and send it, increment counter
readDataFromFlash(flashOpCurAddr1, flashOpCurAddr2, size, (void*)incomingData);
usbSendMessage(CMD_EXPORT_FLASH, size, incomingData);
//usbSendMessageWithRetries(CMD_EXPORT_FLASH, size, (char*)incomingData, 255);
flashOpCurAddr2 += size;
if (flashOpCurAddr2 == BYTES_PER_PAGE)
{
flashOpCurAddr2 = 0;
flashOpCurAddr1++;
}
// Skip over the graphics address if we're in that case
if (flashOpCurAddr1 == GRAPHIC_ZONE_PAGE_START)
{
flashOpCurAddr1 = GRAPHIC_ZONE_PAGE_END;
}
return;
}
// flash export end
case CMD_EXPORT_FLASH_END :
{
currentFlashOpUid = 0;
return;
}
// flash export start
case CMD_EXPORT_EEPROM_START :
{
approveImportExportMemoryOperation(CMD_EXPORT_EEPROM_START, &plugin_return_value);
guiGetBackToCurrentScreen();
break;
}
// export eeprom contents
case CMD_EXPORT_EEPROM :
{
uint8_t size = PACKET_EXPORT_SIZE;
// Check that the user approved
if (currentFlashOpUid != CMD_EXPORT_EEPROM_START)
{
return;
}
//flashOpCurAddr1 is the current eeprom address
// Check if the export address is correct
if (flashOpCurAddr1 >= EEPROM_SIZE)
{
usbSendMessage(CMD_EXPORT_EEPROM_END, 0, NULL);
USBPARSERDEBUGPRINTF_P(PSTR("export: end\n"));
currentFlashOpUid = 0;
return;
}
// Check how much data we need
if ((EEPROM_SIZE - flashOpCurAddr1) < PACKET_EXPORT_SIZE)
{
size = (uint8_t)(EEPROM_SIZE - flashOpCurAddr1);
}
// Get a block of data and send it, increment counter
eeprom_read_block(incomingData, (void*)flashOpCurAddr1, size);
usbSendMessage(CMD_EXPORT_EEPROM, size, (char*)incomingData);
//usbSendMessageWithRetries(CMD_EXPORT_EEPROM, size, (char*)incomingData, 255);
flashOpCurAddr1 += size;
return;
}
// end eeprom export
case CMD_EXPORT_EEPROM_END :
{
currentFlashOpUid = 0;
return;
}
// import flash contents
case CMD_IMPORT_FLASH_BEGIN :
{
// Check datalen for arg
if (datalen != 1)
{
USBPARSERDEBUGPRINTF_P(PSTR("import: no param\n"));
return;
}
// Ask user approval
approveImportExportMemoryOperation(CMD_IMPORT_FLASH_BEGIN, &plugin_return_value);
//flashOpCurAddr1 is the page
//flashOpCurAddr2 is the offset
// Check what we want to write
if (msg->body.data[0] == 0x00)
{
flashOpCurAddr1 = 0x0000;
flash_import_user_space = TRUE;
}
else
{
flash_import_user_space = FALSE;
flashOpCurAddr1 = GRAPHIC_ZONE_PAGE_START;
}
// Get back to normal screen
guiGetBackToCurrentScreen();
break;
}
// import flash contents
case CMD_IMPORT_FLASH :
{
// Check if we actually approved the import, haven't gone over the flash boundaries, if we're correctly aligned page size wise
if ((currentFlashOpUid != CMD_IMPORT_FLASH_BEGIN) || (flashOpCurAddr1 >= PAGE_COUNT) || (flashOpCurAddr2 + datalen > BYTES_PER_PAGE) || ((flash_import_user_space == FALSE) && (flashOpCurAddr1 >= GRAPHIC_ZONE_PAGE_END)))
{
plugin_return_value = PLUGIN_BYTE_ERROR;
currentFlashOpUid = 0;
}
else
{
flashWriteBuffer(msg->body.data, flashOpCurAddr2, datalen);
flashOpCurAddr2+= datalen;
// If we just filled a page, flush it to the page
if (flashOpCurAddr2 == BYTES_PER_PAGE)
{
flashWriteBufferToPage(flashOpCurAddr1);
flashOpCurAddr2 = 0;
flashOpCurAddr1++;
// If we are importing user contents, skip the graphics zone
if ((flash_import_user_space == TRUE) && (flashOpCurAddr1 == GRAPHIC_ZONE_PAGE_START))
{
flashOpCurAddr1 = GRAPHIC_ZONE_PAGE_END;
}
}
plugin_return_value = PLUGIN_BYTE_OK;
}
break;
}
// end flash import
case CMD_IMPORT_FLASH_END :
{
if ((currentFlashOpUid == CMD_IMPORT_FLASH_BEGIN) && (flashOpCurAddr2 != 0))
{
flashWriteBufferToPage(flashOpCurAddr1);
}
plugin_return_value = PLUGIN_BYTE_OK;
currentFlashOpUid = 0;
break;
}
// import flash contents
case CMD_IMPORT_EEPROM_BEGIN :
{
// Ask for user confirmation
approveImportExportMemoryOperation(CMD_IMPORT_EEPROM_BEGIN, &plugin_return_value);
guiGetBackToCurrentScreen();
break;
}
// import flash contents
case CMD_IMPORT_EEPROM :
{
// flashOpCurAddr1 is the current eeprom address
if ((currentFlashOpUid != CMD_IMPORT_EEPROM_BEGIN) || ((flashOpCurAddr1 + datalen) >= EEPROM_SIZE))
{
plugin_return_value = PLUGIN_BYTE_ERROR;
currentFlashOpUid = 0;
}
else
{
eeprom_write_block((void*)msg->body.data, (void*)flashOpCurAddr1, datalen);
flashOpCurAddr1+= datalen;
plugin_return_value = PLUGIN_BYTE_OK;
}
break;
}
// end eeprom import
case CMD_IMPORT_EEPROM_END :
{
plugin_return_value = PLUGIN_BYTE_OK;
currentFlashOpUid = 0;
break;
}
#endif
// set password bootkey
case CMD_SET_BOOTLOADER_PWD :
{
if ((eeprom_read_byte((uint8_t*)EEP_BOOT_PWD_SET) != BOOTLOADER_PWDOK_KEY) && (datalen == PACKET_EXPORT_SIZE))
{
eeprom_write_block((void*)msg->body.data, (void*)EEP_BOOT_PWD, PACKET_EXPORT_SIZE);
eeprom_write_byte((uint8_t*)EEP_BOOT_PWD_SET, BOOTLOADER_PWDOK_KEY);
plugin_return_value = PLUGIN_BYTE_OK;
}
else
{
plugin_return_value = PLUGIN_BYTE_ERROR;
}
break;
}
// Jump to bootloader
case CMD_JUMP_TO_BOOTLOADER :
{
#ifndef DEV_PLUGIN_COMMS
uint8_t temp_buffer[PACKET_EXPORT_SIZE];
#endif
// Mandatory wait for bruteforce
userViewDelay();
#ifdef DEV_PLUGIN_COMMS
// Write "jump to bootloader" key in eeprom
eeprom_write_word((uint16_t*)EEP_BOOTKEY_ADDR, BOOTLOADER_BOOTKEY);
// Use WDT to reset the device
cli();
wdt_reset();
wdt_clear_flag();
wdt_change_enable();
wdt_enable_2s();
sei();
while(1);
#else
if ((eeprom_read_byte((uint8_t*)EEP_BOOT_PWD_SET) == BOOTLOADER_PWDOK_KEY) && (datalen == PACKET_EXPORT_SIZE))
{
eeprom_read_block((void*)temp_buffer, (void*)EEP_BOOT_PWD, PACKET_EXPORT_SIZE);
if (memcmp((void*)temp_buffer, (void*)msg->body.data, PACKET_EXPORT_SIZE) == 0)
{
// Write "jump to bootloader" key in eeprom
eeprom_write_word((uint16_t*)EEP_BOOTKEY_ADDR, BOOTLOADER_BOOTKEY);
// Use WDT to reset the device
cli();
wdt_reset();
wdt_clear_flag();
wdt_change_enable();
wdt_enable_2s();
sei();
while(1);
}
}
#endif
}
// Development commands
#ifdef DEV_PLUGIN_COMMS
// erase eeprom
case CMD_ERASE_EEPROM :
{
eraseFlashUsersContents();
firstTimeUserHandlingInit();
plugin_return_value = PLUGIN_BYTE_OK;
break;
}
// erase flash
case CMD_ERASE_FLASH :
{
eraseFlashUsersContents();
plugin_return_value = PLUGIN_BYTE_OK;
break;
}
// erase eeprom
case CMD_ERASE_SMC :
{
if (getSmartCardInsertedUnlocked() == TRUE)
{
eraseSmartCard();
plugin_return_value = PLUGIN_BYTE_OK;
}
else
{
plugin_return_value = PLUGIN_BYTE_ERROR;
}
break;
}
case CMD_DRAW_BITMAP :
{
usbPrintf_P(PSTR("draw bitmap file %d\n"), msg->body.data[0]);
if (msg->body.data[3] != 0) // clear
{
oledWriteActiveBuffer();
oledClear();
oledBitmapDrawFlash(msg->body.data[1], msg->body.data[2], msg->body.data[0], 0);
}
else
{
// don't clear, overlay active screen
oledWriteActiveBuffer();
oledBitmapDrawFlash(msg->body.data[1], msg->body.data[2], msg->body.data[0], 0);
}
return;
}
case CMD_CLONE_SMARTCARD :
{
if (cloneSmartCardProcess(SMARTCARD_DEFAULT_PIN) == RETURN_OK)
{
plugin_return_value = PLUGIN_BYTE_OK;
}
else
{
plugin_return_value = PLUGIN_BYTE_ERROR;
}
break;
}
case CMD_SET_FONT :
{
usbPrintf_P(PSTR("set font file %d\n"), msg->body.data[0]);
oledSetFont(msg->body.data[0]);
if (datalen > 1) {
usbPrintf_P(PSTR("testing string \"%s\"\n"), (char *)&msg->body.data[1]);
oledFlipBuffers(0,0);
oledWriteActiveBuffer();
oledClear();
oledPutstr((char *)&msg->body.data[1]);
}
return;
}
case CMD_STACK_FREE:
usbPutstr("Stack Free ");
int_to_string(stackFree(),stack_str);
usbPutstr(stack_str);
usbPutstr(" bytes\n");
return;
#endif
default : return;
}
usbSendMessage(datacmd, 1, &plugin_return_value);
}
/*! \fn usbProcessIncoming(uint8_t* incomingData)
* \brief Process the incoming USB packet
* \param incomingData Pointer to the packet (can be overwritten!)
*/
void usbProcessIncoming(uint8_t* incomingData)
{
// Temp plugin return value, error by default
uint8_t plugin_return_value = PLUGIN_BYTE_ERROR;
// Use message structure
usbMsg_t* msg = (usbMsg_t*)incomingData;
// Get data len
uint8_t datalen = msg->len;
// Get data cmd
uint8_t datacmd = msg->cmd;
#ifdef USB_FEATURE_PLUGIN_COMMS
// Temp ret_type
RET_TYPE temp_rettype;
#endif
#ifdef DEV_PLUGIN_COMMS
char stack_str[10];
#endif
// Debug comms
// USBDEBUGPRINTF_P(PSTR("usb: rx cmd 0x%02x len %u\n"), datacmd, datalen);
switch(datacmd)
{
// ping command
case CMD_PING :
{
usbSendMessage(0, 6, msg);
return;
}
// version command
case CMD_VERSION :
{
msg->len = 3; // len + cmd + FLASH_CHIP
msg->cmd = CMD_VERSION;
msg->body.data[0] = FLASH_CHIP;
msg->len += getVersion((char*)&msg->body.data[1], sizeof(msg->body.data) - 1);
usbSendMessage(0, msg->len, msg);
return;
}
#ifdef USB_FEATURE_PLUGIN_COMMS
// context command
case CMD_CONTEXT :
{
if (checkTextField(msg->body.data, datalen, NODE_PARENT_SIZE_OF_SERVICE) == RETURN_NOK)
{
plugin_return_value = PLUGIN_BYTE_ERROR;
USBPARSERDEBUGPRINTF_P(PSTR("setCtx: len %d too big\n"), datalen);
}
else if (getSmartCardInsertedUnlocked() != TRUE)
{
plugin_return_value = PLUGIN_BYTE_NOCARD;
USBPARSERDEBUGPRINTF_P(PSTR("set context: no card\n"));
}
else if (setCurrentContext(msg->body.data, datalen) == RETURN_OK)
{
plugin_return_value = PLUGIN_BYTE_OK;
USBPARSERDEBUGPRINTF_P(PSTR("set context: \"%s\" ok\n"), msg->body.data);
}
else
{
plugin_return_value = PLUGIN_BYTE_ERROR;
USBPARSERDEBUGPRINTF_P(PSTR("set context: \"%s\" failed\n"), msg->body.data);
}
break;
}
// get login
case CMD_GET_LOGIN :
{
if (getLoginForContext((char*)incomingData) == RETURN_OK)
{
// Use the buffer to store the login...
usbSendMessage(CMD_GET_LOGIN, strlen((char*)incomingData)+1, incomingData);
USBPARSERDEBUGPRINTF_P(PSTR("get login: \"%s\"\n"),(char *)incomingData);
return;
}
else
{
plugin_return_value = PLUGIN_BYTE_ERROR;
USBPARSERDEBUGPRINTF_P(PSTR("get login: failed\n"));
}
break;
}
// get password
case CMD_GET_PASSWORD :
{
if (getPasswordForContext((char*)incomingData) == RETURN_OK)
{
usbSendMessage(CMD_GET_PASSWORD, strlen((char*)incomingData)+1, incomingData);
USBPARSERDEBUGPRINTF_P(PSTR("get pass: \"%s\"\n"),(char *)incomingData);
return;
}
else
{
plugin_return_value = PLUGIN_BYTE_ERROR;
USBPARSERDEBUGPRINTF_P(PSTR("get pass: failed\n"));
}
break;
}
// set login
case CMD_SET_LOGIN :
{
if (checkTextField(msg->body.data, datalen, NODE_CHILD_SIZE_OF_LOGIN) == RETURN_NOK)
{
plugin_return_value = PLUGIN_BYTE_ERROR;
USBPARSERDEBUGPRINTF_P(PSTR("set login: \"%s\" checkTextField failed\n"),msg->body.data);
}
else if (setLoginForContext(msg->body.data, datalen) == RETURN_OK)
{
plugin_return_value = PLUGIN_BYTE_OK;
USBPARSERDEBUGPRINTF_P(PSTR("set login: \"%s\" ok\n"),msg->body.data);
}
else
{
plugin_return_value = PLUGIN_BYTE_ERROR;
USBPARSERDEBUGPRINTF_P(PSTR("set login: \"%s\" failed\n"),msg->body.data);
}
break;
}
// set password
case CMD_SET_PASSWORD :
{
if (checkTextField(msg->body.data, datalen, NODE_CHILD_SIZE_OF_PASSWORD) == RETURN_NOK)
{
plugin_return_value = PLUGIN_BYTE_ERROR;
USBPARSERDEBUGPRINTF_P(PSTR("set pass: len %d invalid\n"), datalen);
}
else if (setPasswordForContext(msg->body.data, datalen) == RETURN_OK)
{
plugin_return_value = PLUGIN_BYTE_OK;
USBPARSERDEBUGPRINTF_P(PSTR("set pass: \"%s\" ok\n"),msg->body.data);
}
else
{
plugin_return_value = PLUGIN_BYTE_ERROR;
USBPARSERDEBUGPRINTF_P(PSTR("set pass: failed\n"));
}
break;
}
// check password
case CMD_CHECK_PASSWORD :
{
if (checkTextField(msg->body.data, datalen, NODE_CHILD_SIZE_OF_PASSWORD) == RETURN_NOK)
{
plugin_return_value = PLUGIN_BYTE_ERROR;
break;
}
temp_rettype = checkPasswordForContext(msg->body.data, datalen);
if (temp_rettype == RETURN_PASS_CHECK_NOK)
{
plugin_return_value = PLUGIN_BYTE_ERROR;
}
else if(temp_rettype == RETURN_PASS_CHECK_OK)
{
plugin_return_value = PLUGIN_BYTE_OK;
}
else
{
plugin_return_value = PLUGIN_BYTE_NA;
}
break;
}
// set password
case CMD_ADD_CONTEXT :
{
if (checkTextField(msg->body.data, datalen, NODE_PARENT_SIZE_OF_SERVICE) == RETURN_NOK)
{
// Check field
plugin_return_value = PLUGIN_BYTE_ERROR;
USBPARSERDEBUGPRINTF_P(PSTR("set context: len %d invalid\n"), datalen);
}
else if (addNewContext(msg->body.data, datalen) == RETURN_OK)
{
// We managed to add a new context
plugin_return_value = PLUGIN_BYTE_OK;
USBPARSERDEBUGPRINTF_P(PSTR("add context: \"%s\" ok\n"),msg->body.data);
}
else
{
// Couldn't add a new context
plugin_return_value = PLUGIN_BYTE_ERROR;
USBPARSERDEBUGPRINTF_P(PSTR("add context: \"%s\" failed\n"),msg->body.data);
}
break;
}
#endif
#ifdef FLASH_BLOCK_IMPORT_EXPORT
// flash export start
case CMD_EXPORT_FLASH_START :
{
approveImportExportMemoryOperation(CMD_EXPORT_FLASH_START, &plugin_return_value);
guiGetBackToCurrentScreen();
break;
}
// export flash contents
case CMD_EXPORT_FLASH :
{
uint8_t size = PACKET_EXPORT_SIZE;
// Check that the user approved
if (currentFlashOpUid != CMD_EXPORT_FLASH_START)
{
return;
}
//flashOpCurAddr1 is the page
//flashOpCurAddr2 is the offset
// Check if the export address is correct
if (flashOpCurAddr1 >= PAGE_COUNT)
{
usbSendMessage(CMD_EXPORT_FLASH_END, 0, NULL);
USBPARSERDEBUGPRINTF_P(PSTR("export: end\n"));
currentFlashOpUid = 0;
return;
}
// Check how much data we need in case we're close to the page end
if ((BYTES_PER_PAGE - flashOpCurAddr2) < PACKET_EXPORT_SIZE)
{
size = (uint8_t)(BYTES_PER_PAGE - flashOpCurAddr2);
}
// Get a block of data and send it, increment counter
readDataFromFlash(flashOpCurAddr1, flashOpCurAddr2, size, (void*)incomingData);
usbSendMessage(CMD_EXPORT_FLASH, size, incomingData);
//usbSendMessageWithRetries(CMD_EXPORT_FLASH, size, (char*)incomingData, 255);
flashOpCurAddr2 += size;
if (flashOpCurAddr2 == BYTES_PER_PAGE)
{
flashOpCurAddr2 = 0;
flashOpCurAddr1++;
}
// Skip over the graphics address if we're in that case
if (flashOpCurAddr1 == GRAPHIC_ZONE_PAGE_START)
{
flashOpCurAddr1 = GRAPHIC_ZONE_PAGE_END;
}
return;
}
// flash export end
case CMD_EXPORT_FLASH_END :
{
currentFlashOpUid = 0;
return;
}
// flash export start
case CMD_EXPORT_EEPROM_START :
{
approveImportExportMemoryOperation(CMD_EXPORT_EEPROM_START, &plugin_return_value);
guiGetBackToCurrentScreen();
break;
}
// export eeprom contents
case CMD_EXPORT_EEPROM :
{
uint8_t size = PACKET_EXPORT_SIZE;
// Check that the user approved
if (currentFlashOpUid != CMD_EXPORT_EEPROM_START)
{
return;
}
//flashOpCurAddr1 is the current eeprom address
// Check if the export address is correct
if (flashOpCurAddr1 >= EEPROM_SIZE)
{
usbSendMessage(CMD_EXPORT_EEPROM_END, 0, NULL);
USBPARSERDEBUGPRINTF_P(PSTR("export: end\n"));
currentFlashOpUid = 0;
return;
}
// Check how much data we need
if ((EEPROM_SIZE - flashOpCurAddr1) < PACKET_EXPORT_SIZE)
{
size = (uint8_t)(EEPROM_SIZE - flashOpCurAddr1);
}
// Get a block of data and send it, increment counter
eeprom_read_block(incomingData, (void*)flashOpCurAddr1, size);
usbSendMessage(CMD_EXPORT_EEPROM, size, (char*)incomingData);
//usbSendMessageWithRetries(CMD_EXPORT_EEPROM, size, (char*)incomingData, 255);
flashOpCurAddr1 += size;
return;
}
// end eeprom export
case CMD_EXPORT_EEPROM_END :
{
currentFlashOpUid = 0;
return;
}
// import flash contents
case CMD_IMPORT_FLASH_BEGIN :
{
// Check datalen for arg
if (datalen != 1)
{
USBPARSERDEBUGPRINTF_P(PSTR("import: no param\n"));
return;
}
// Ask user approval
approveImportExportMemoryOperation(CMD_IMPORT_FLASH_BEGIN, &plugin_return_value);
//flashOpCurAddr1 is the page
//flashOpCurAddr2 is the offset
// Check what we want to write
if (msg->body.data[0] == 0x00)
{
flashOpCurAddr1 = 0x0000;
flash_import_user_space = TRUE;
}
else
{
flash_import_user_space = FALSE;
flashOpCurAddr1 = GRAPHIC_ZONE_PAGE_START;
}
// Get back to normal screen
guiGetBackToCurrentScreen();
break;
}
// import flash contents
case CMD_IMPORT_FLASH :
{
// Check if we actually approved the import, haven't gone over the flash boundaries, if we're correctly aligned page size wise
if ((currentFlashOpUid != CMD_IMPORT_FLASH_BEGIN) || (flashOpCurAddr1 >= PAGE_COUNT) || (flashOpCurAddr2 + datalen > BYTES_PER_PAGE) || ((flash_import_user_space == FALSE) && (flashOpCurAddr1 >= GRAPHIC_ZONE_PAGE_END)))
{
plugin_return_value = PLUGIN_BYTE_ERROR;
currentFlashOpUid = 0;
}
else
{
flashWriteBuffer(msg->body.data, flashOpCurAddr2, datalen);
flashOpCurAddr2+= datalen;
// If we just filled a page, flush it to the page
if (flashOpCurAddr2 == BYTES_PER_PAGE)
{
flashWriteBufferToPage(flashOpCurAddr1);
flashOpCurAddr2 = 0;
flashOpCurAddr1++;
// If we are importing user contents, skip the graphics zone
if ((flash_import_user_space == TRUE) && (flashOpCurAddr1 == GRAPHIC_ZONE_PAGE_START))
{
flashOpCurAddr1 = GRAPHIC_ZONE_PAGE_END;
}
}
plugin_return_value = PLUGIN_BYTE_OK;
}
break;
}
// end flash import
case CMD_IMPORT_FLASH_END :
{
if ((currentFlashOpUid == CMD_IMPORT_FLASH_BEGIN) && (flashOpCurAddr2 != 0))
{
flashWriteBufferToPage(flashOpCurAddr1);
}
plugin_return_value = PLUGIN_BYTE_OK;
currentFlashOpUid = 0;
break;
}
// import flash contents
case CMD_IMPORT_EEPROM_BEGIN :
{
// Ask for user confirmation
approveImportExportMemoryOperation(CMD_IMPORT_EEPROM_BEGIN, &plugin_return_value);
guiGetBackToCurrentScreen();
break;
}
// import flash contents
case CMD_IMPORT_EEPROM :
{
// flashOpCurAddr1 is the current eeprom address
if ((currentFlashOpUid != CMD_IMPORT_EEPROM_BEGIN) || ((flashOpCurAddr1 + datalen) >= EEPROM_SIZE))
{
plugin_return_value = PLUGIN_BYTE_ERROR;
currentFlashOpUid = 0;
}
else
{
eeprom_write_block((void*)msg->body.data, (void*)flashOpCurAddr1, datalen);
flashOpCurAddr1+= datalen;
plugin_return_value = PLUGIN_BYTE_OK;
}
break;
}
// end eeprom import
case CMD_IMPORT_EEPROM_END :
{
plugin_return_value = PLUGIN_BYTE_OK;
currentFlashOpUid = 0;
break;
}
#endif
#ifdef NODE_BLOCK_IMPORT_EXPORT
// Read user profile in flash
case CMD_START_MEMORYMGMT :
{
// Check that the smartcard is unlocked
if (getSmartCardInsertedUnlocked() == TRUE)
{
// If so, ask the user to approve memory management mode
approveMemoryManagementMode(&plugin_return_value);
}
break;
}
// Read starting parent
case CMD_GET_STARTING_PARENT :
{
// Check that we're actually in memory management mode
if (memoryManagementModeApproved == TRUE)
{
// Read starting parent
uint16_t temp_address = getStartingParentAddress();
// Send address
usbSendMessage(CMD_GET_STARTING_PARENT, 2, (uint8_t*)&temp_address);
// Return
return;
}
else
{
plugin_return_value = PLUGIN_BYTE_ERROR;
}
break;
}
// Get a free node address
case CMD_GET_FREE_SLOT_ADDR :
{
// Check that we're actually in memory management mode
if (memoryManagementModeApproved == TRUE)
{
uint16_t temp_address;
// Scan for next free node address
scanNodeUsage();
// Store next free node address
temp_address = getFreeNodeAddress();
// Send address
usbSendMessage(CMD_GET_FREE_SLOT_ADDR, 2, (uint8_t*)&temp_address);
return;
}
else
{
plugin_return_value = PLUGIN_BYTE_ERROR;
}
break;
}
// End memory management mode
case CMD_END_MEMORYMGMT :
{
// Check that we're actually in memory management mode
if (memoryManagementModeApproved == TRUE)
{
// memoryManagementModeApproved is cleared when user removes his card
guiSetCurrentScreen(SCREEN_DEFAULT_INSERTED_NLCK);
plugin_return_value = PLUGIN_BYTE_OK;
leaveMemoryManagementMode();
guiGetBackToCurrentScreen();
populateServicesLut();
scanNodeUsage();
}
else
{
plugin_return_value = PLUGIN_BYTE_ERROR;
}
break;
}
// Read node from Flash
case CMD_READ_FLASH_NODE :
{
// Check that the mode is approved & that args are supplied
if ((memoryManagementModeApproved == TRUE) && (datalen == 2))
{
uint16_t* temp_uint_ptr = (uint16_t*)msg->body.data;
uint8_t temp_buffer[NODE_SIZE];
// Read node in flash & send it, ownership check is done in the function
readNode((gNode*)temp_buffer, *temp_uint_ptr);
usbSendMessage(CMD_READ_FLASH_NODE, NODE_SIZE, temp_buffer);
return;
}
else
{
plugin_return_value = PLUGIN_BYTE_ERROR;
}
break;
}
// Set favorite
case CMD_SET_FAVORITE :
{
// Check that the mode is approved & that args are supplied
if ((memoryManagementModeApproved == TRUE) && (datalen == 5))
{
uint16_t* temp_par_addr = (uint16_t*)&msg->body.data[1];
uint16_t* temp_child_addr = (uint16_t*)&msg->body.data[3];
setFav(msg->body.data[0], *temp_par_addr, *temp_child_addr);
plugin_return_value = PLUGIN_BYTE_OK;
}
else
{
plugin_return_value = PLUGIN_BYTE_ERROR;
}
break;
}
// Get favorite
case CMD_GET_FAVORITE :
{
// Check that the mode is approved & that args are supplied
if ((memoryManagementModeApproved == TRUE) && (datalen == 1))
{
uint16_t data[2];
readFav(msg->body.data[0], &data[0], &data[1]);
usbSendMessage(CMD_GET_FAVORITE, 4, (void*)data);
return;
}
else
{
plugin_return_value = PLUGIN_BYTE_ERROR;
}
break;
}
// Set starting parent
case CMD_SET_STARTINGPARENT :
{
// Check that the mode is approved & that args are supplied
if ((memoryManagementModeApproved == TRUE) && (datalen == 2))
{
uint16_t* temp_par_addr = (uint16_t*)&msg->body.data[0];
setStartingParent(*temp_par_addr);
plugin_return_value = PLUGIN_BYTE_OK;
}
else
{
plugin_return_value = PLUGIN_BYTE_ERROR;
}
break;
}
// Set new CTR value
case CMD_SET_CTRVALUE :
{
// Check that the mode is approved & that args are supplied
if ((memoryManagementModeApproved == TRUE) && (datalen == USER_CTR_SIZE))
{
setProfileCtr(msg->body.data);
plugin_return_value = PLUGIN_BYTE_OK;
}
else
{
plugin_return_value = PLUGIN_BYTE_ERROR;
}
break;
}
// Get CTR value
case CMD_GET_CTRVALUE :
{
// Check that the mode is approved & that args are supplied
if (memoryManagementModeApproved == TRUE)
{
// Temp buffer to store CTR
uint8_t tempCtrVal[USER_CTR_SIZE];
// Read CTR value
readProfileCtr(tempCtrVal);
// Send it
usbSendMessage(CMD_GET_CTRVALUE, USER_CTR_SIZE, tempCtrVal);
return;
}
else
{
plugin_return_value = PLUGIN_BYTE_ERROR;
}
break;
}
// Add a known card to the MP, 8 first bytes is the CPZ, next 16 is the CTR nonce
case CMD_ADD_CARD_CPZ_CTR :
{
// Check that the mode is approved & that args are supplied
if ((memoryManagementModeApproved == TRUE) && (datalen == SMARTCARD_CPZ_LENGTH + AES256_CTR_LENGTH))
{
writeSmartCardCPZForUserId(msg->body.data, &msg->body.data[SMARTCARD_CPZ_LENGTH], getCurrentUserID());
plugin_return_value = PLUGIN_BYTE_OK;
}
else
{
plugin_return_value = PLUGIN_BYTE_ERROR;
}
break;
}
// Get all the cpz ctr values for current user
case CMD_GET_CARD_CPZ_CTR :
{
// Check that the mode is approved
if (memoryManagementModeApproved == TRUE)
{
outputLUTEntriesForGivenUser(getCurrentUserID());
plugin_return_value = PLUGIN_BYTE_OK;
}
else
{
plugin_return_value = PLUGIN_BYTE_ERROR;
}
break;
}
// Write node in Flash
case CMD_WRITE_FLASH_NODE :
{
// First two bytes are the node address
uint16_t* temp_node_addr_ptr = (uint16_t*)msg->body.data;
uint16_t temp_flags;
// Check that the plugin provided the address and packet #
if ((memoryManagementModeApproved != TRUE) || (datalen != 3))
{
plugin_return_value = PLUGIN_BYTE_ERROR;
}
else
{
// If it is the first packet, store the address and load the page in the internal buffer
if (msg->body.data[2] == 0)
{
// Read the flags and check we're not overwriting someone else's data
readDataFromFlash(pageNumberFromAddress(*temp_node_addr_ptr), NODE_SIZE * nodeNumberFromAddress(*temp_node_addr_ptr), 2, (void*)&temp_flags);
// Either the node belongs to us or it is invalid
if((getCurrentUserID() == userIdFromFlags(temp_flags)) || (validBitFromFlags(temp_flags) == NODE_VBIT_INVALID))
{
currentNodeWritten = *temp_node_addr_ptr;
loadPageToInternalBuffer(pageNumberFromAddress(currentNodeWritten));
}
}
// Check that the address the plugin wants to write is the one stored and that we're not writing more than we're supposed to
if ((currentNodeWritten == *temp_node_addr_ptr) && (currentNodeWritten != NODE_ADDR_NULL) && (msg->body.data[2] * (PACKET_EXPORT_SIZE-3) + datalen < NODE_SIZE))
{
// If it's the first packet, set correct user ID
if (msg->body.data[2] == 0)
{
userIdToFlags((uint16_t*)&(msg->body.data[3]), getCurrentUserID());
}
// Fill the data at the right place
flashWriteBuffer(msg->body.data + 3, (NODE_SIZE * nodeNumberFromAddress(currentNodeWritten)) + (msg->body.data[2] * (PACKET_EXPORT_SIZE-3)), datalen - 3);
// If we finished writing, flush buffer
if (msg->body.data[2] == (NODE_SIZE/(PACKET_EXPORT_SIZE-3)))
{
flashWriteBufferToPage(pageNumberFromAddress(currentNodeWritten));
}
plugin_return_value = PLUGIN_BYTE_OK;
}
else
{
plugin_return_value = PLUGIN_BYTE_ERROR;
}
}
break;
}
#endif
// import media flash contents
case CMD_IMPORT_MEDIA_START :
{
#ifndef DEV_PLUGIN_COMMS
uint8_t temp_buffer[PACKET_EXPORT_SIZE];
#endif
// Set default addresses
mediaFlashImportPage = GRAPHIC_ZONE_PAGE_START;
mediaFlashImportOffset = 0;
// No check if dev comms
#ifdef DEV_PLUGIN_COMMS
plugin_return_value = PLUGIN_BYTE_OK;
mediaFlashImportApproved = TRUE;
#else
// Mandatory wait for bruteforce
userViewDelay();
// Compare with our password, can be 0xFF... if not initialized
if (datalen == PACKET_EXPORT_SIZE)
{
eeprom_read_block((void*)temp_buffer, (void*)EEP_BOOT_PWD, PACKET_EXPORT_SIZE);
if (memcmp((void*)temp_buffer, (void*)msg->body.data, PACKET_EXPORT_SIZE) == 0)
{
plugin_return_value = PLUGIN_BYTE_OK;
mediaFlashImportApproved = TRUE;
}
}
#endif
break;
}
// import media flash contents
case CMD_IMPORT_MEDIA :
{
// Check if we actually approved the import, haven't gone over the flash boundaries, if we're correctly aligned page size wise
if ((mediaFlashImportApproved == FALSE) || (mediaFlashImportPage >= GRAPHIC_ZONE_PAGE_END) || (mediaFlashImportOffset + datalen > BYTES_PER_PAGE))
{
plugin_return_value = PLUGIN_BYTE_ERROR;
mediaFlashImportApproved = FALSE;
}
else
{
flashWriteBuffer(msg->body.data, mediaFlashImportOffset, datalen);
mediaFlashImportOffset+= datalen;
// If we just filled a page, flush it to the page
if (mediaFlashImportOffset == BYTES_PER_PAGE)
{
flashWriteBufferToPage(mediaFlashImportPage);
mediaFlashImportOffset = 0;
mediaFlashImportPage++;
}
plugin_return_value = PLUGIN_BYTE_OK;
}
break;
}
// end media flash import
case CMD_IMPORT_MEDIA_END :
{
if ((mediaFlashImportApproved == TRUE) && (mediaFlashImportOffset != 0))
{
flashWriteBufferToPage(mediaFlashImportPage);
}
plugin_return_value = PLUGIN_BYTE_OK;
mediaFlashImportApproved = FALSE;
break;
}
// Set Mooltipass param
case CMD_SET_MOOLTIPASS_PARM :
{
// Check that args are supplied
if (datalen == 2)
{
setMooltipassParameterInEeprom(msg->body.data[0], msg->body.data[1]);
plugin_return_value = PLUGIN_BYTE_OK;
}
else
{
plugin_return_value = PLUGIN_BYTE_ERROR;
}
break;
}
// Get Mooltipass param
case CMD_GET_MOOLTIPASS_PARM :
{
plugin_return_value = getMooltipassParameterInEeprom(msg->body.data[0]);
break;
}
// Reset smartcard
case CMD_RESET_CARD :
{
uint16_t* temp_uint_pt = (uint16_t*)msg->body.data;
// Check the args, check we're not authenticated, check that the card detection returns a user card, try unlocking the card with provided PIN
if ((datalen == 2) && (getCurrentScreen() == SCREEN_DEFAULT_INSERTED_UNKNOWN) && (mooltipassDetectedRoutine(swap16(*temp_uint_pt)) == RETURN_MOOLTIPASS_4_TRIES_LEFT))
{
eraseSmartCard();
plugin_return_value = PLUGIN_BYTE_OK;
}
else
{
plugin_return_value = PLUGIN_BYTE_ERROR;
}
break;
}
// Add current unknown smartcard
case CMD_ADD_UNKNOWN_CARD :
{
uint16_t* temp_uint_pt = (uint16_t*)msg->body.data;
// Check the args, check we're not authenticated, check that the card detection returns a user card, try unlocking the card with provided PIN
if ((datalen == (2 + AES256_CTR_LENGTH)) && (getCurrentScreen() == SCREEN_DEFAULT_INSERTED_UNKNOWN) && (mooltipassDetectedRoutine(swap16(*temp_uint_pt)) == RETURN_MOOLTIPASS_4_TRIES_LEFT))
{
addNewUserForExistingCard(msg->body.data + 2);
plugin_return_value = PLUGIN_BYTE_OK;
}
else
{
plugin_return_value = PLUGIN_BYTE_ERROR;
}
break;
}
// Read card login
case CMD_READ_CARD_LOGIN :
{
if (getSmartCardInsertedUnlocked() == TRUE)
{
uint8_t temp_data[SMARTCARD_MTP_LOGIN_LENGTH/8];
readMooltipassWebsiteLogin(temp_data);
usbSendMessage(CMD_READ_CARD_LOGIN, sizeof(temp_data), (void*)temp_data);
return;
}
else
{
plugin_return_value = PLUGIN_BYTE_ERROR;
}
break;
}
// Read card stored password
case CMD_READ_CARD_PASS :
{
if (getSmartCardInsertedUnlocked() == TRUE)
{
if (guiAskForConfirmation(1, (confirmationText_t*)readStoredStringToBuffer(ID_STRING_SEND_SMC_PASS)) == RETURN_OK)
{
uint8_t temp_data[SMARTCARD_MTP_PASS_LENGTH/8];
readMooltipassWebsitePassword(temp_data);
usbSendMessage(CMD_READ_CARD_PASS, sizeof(temp_data), (void*)temp_data);
guiGetBackToCurrentScreen();
return;
}
else
{
guiGetBackToCurrentScreen();
plugin_return_value = PLUGIN_BYTE_ERROR;
}
}
else
{
plugin_return_value = PLUGIN_BYTE_ERROR;
}
break;
}
// Set card login
case CMD_SET_CARD_LOGIN :
{
if ((checkTextField(msg->body.data, datalen, SMARTCARD_MTP_LOGIN_LENGTH/8) == RETURN_OK) && (getSmartCardInsertedUnlocked() == TRUE))
{
if (guiAskForConfirmation(1, (confirmationText_t*)readStoredStringToBuffer(ID_STRING_SET_SMC_LOGIN)) == RETURN_OK)
{
// Temp buffer for application zone 2
uint8_t temp_az2[SMARTCARD_AZ_BIT_LENGTH/8];
// Read Application Zone 2
readApplicationZone2(temp_az2);
// Erase Application Zone 2
eraseApplicationZone1NZone2SMC(FALSE);
// Write our data in the buffer at the right spot
memcpy(temp_az2 + (SMARTCARD_MTP_LOGIN_OFFSET/8), msg->body.data, datalen);
// Write the new data in the card
writeApplicationZone2(temp_az2);
// Return OK
plugin_return_value = PLUGIN_BYTE_OK;
}
else
{
plugin_return_value = PLUGIN_BYTE_ERROR;
}
guiGetBackToCurrentScreen();
}
else
{
plugin_return_value = PLUGIN_BYTE_ERROR;
}
break;
}
// Set card stored password
case CMD_SET_CARD_PASS :
{
if ((checkTextField(msg->body.data, datalen, SMARTCARD_MTP_PASS_LENGTH/8) == RETURN_OK) && (getSmartCardInsertedUnlocked() == TRUE))
{
if (guiAskForConfirmation(1, (confirmationText_t*)readStoredStringToBuffer(ID_STRING_SET_SMC_PASS)) == RETURN_OK)
{
// Temp buffer for application zone 1
uint8_t temp_az1[SMARTCARD_AZ_BIT_LENGTH/8];
// Read Application Zone 1
readApplicationZone1(temp_az1);
// Erase Application Zone 1
eraseApplicationZone1NZone2SMC(TRUE);
// Write our data in buffer
memcpy(temp_az1 + (SMARTCARD_MTP_PASS_OFFSET/8), msg->body.data, datalen);
// Write the new data in the card
writeApplicationZone1(temp_az1);
// Return OK
plugin_return_value = PLUGIN_BYTE_OK;
}
else
{
plugin_return_value = PLUGIN_BYTE_ERROR;
}
guiGetBackToCurrentScreen();
}
else
{
plugin_return_value = PLUGIN_BYTE_ERROR;
}
break;
}
// Get 32 random bytes
case CMD_GET_RANDOM_NUMBER :
{
uint8_t randomBytes[32];
fillArrayWithRandomBytes(randomBytes, 32);
usbSendMessage(CMD_GET_RANDOM_NUMBER, 32, randomBytes);
return;
}
// set password bootkey
case CMD_SET_BOOTLOADER_PWD :
{
if ((eeprom_read_byte((uint8_t*)EEP_BOOT_PWD_SET) != BOOTLOADER_PWDOK_KEY) && (datalen == PACKET_EXPORT_SIZE))
{
eeprom_write_block((void*)msg->body.data, (void*)EEP_BOOT_PWD, PACKET_EXPORT_SIZE);
eeprom_write_byte((uint8_t*)EEP_BOOT_PWD_SET, BOOTLOADER_PWDOK_KEY);
plugin_return_value = PLUGIN_BYTE_OK;
}
else
{
plugin_return_value = PLUGIN_BYTE_ERROR;
}
break;
}
// Jump to bootloader
case CMD_JUMP_TO_BOOTLOADER :
{
#ifndef DEV_PLUGIN_COMMS
uint8_t temp_buffer[PACKET_EXPORT_SIZE];
#endif
// Mandatory wait for bruteforce
userViewDelay();
#ifdef DEV_PLUGIN_COMMS
// Write "jump to bootloader" key in eeprom
eeprom_write_word((uint16_t*)EEP_BOOTKEY_ADDR, BOOTLOADER_BOOTKEY);
// Use WDT to reset the device
cli();
wdt_reset();
wdt_clear_flag();
wdt_change_enable();
wdt_enable_2s();
sei();
while(1);
#else
if ((eeprom_read_byte((uint8_t*)EEP_BOOT_PWD_SET) == BOOTLOADER_PWDOK_KEY) && (datalen == PACKET_EXPORT_SIZE))
{
eeprom_read_block((void*)temp_buffer, (void*)EEP_BOOT_PWD, PACKET_EXPORT_SIZE);
if (memcmp((void*)temp_buffer, (void*)msg->body.data, PACKET_EXPORT_SIZE) == 0)
{
// Write "jump to bootloader" key in eeprom
eeprom_write_word((uint16_t*)EEP_BOOTKEY_ADDR, BOOTLOADER_BOOTKEY);
// Set bootloader password bool to FALSE
eeprom_write_byte((uint8_t*)EEP_BOOT_PWD_SET, FALSE);
// Use WDT to reset the device
cli();
wdt_reset();
wdt_clear_flag();
wdt_change_enable();
wdt_enable_2s();
sei();
while(1);
}
}
#endif
}
// Development commands
#ifdef DEV_PLUGIN_COMMS
// erase eeprom
case CMD_ERASE_EEPROM :
{
eraseFlashUsersContents();
firstTimeUserHandlingInit();
plugin_return_value = PLUGIN_BYTE_OK;
break;
}
// erase flash
case CMD_ERASE_FLASH :
{
eraseFlashUsersContents();
plugin_return_value = PLUGIN_BYTE_OK;
break;
}
// erase eeprom
case CMD_ERASE_SMC :
{
if (getSmartCardInsertedUnlocked() == TRUE)
{
eraseSmartCard();
plugin_return_value = PLUGIN_BYTE_OK;
}
else
{
plugin_return_value = PLUGIN_BYTE_ERROR;
}
break;
}
case CMD_DRAW_BITMAP :
{
usbPrintf_P(PSTR("draw bitmap file %d\n"), msg->body.data[0]);
if (msg->body.data[3] != 0) // clear
{
oledWriteActiveBuffer();
oledClear();
oledBitmapDrawFlash(msg->body.data[1], msg->body.data[2], msg->body.data[0], 0);
}
else
{
// don't clear, overlay active screen
oledWriteActiveBuffer();
oledBitmapDrawFlash(msg->body.data[1], msg->body.data[2], msg->body.data[0], 0);
}
return;
}
case CMD_CLONE_SMARTCARD :
{
if (cloneSmartCardProcess(SMARTCARD_DEFAULT_PIN) == RETURN_OK)
{
plugin_return_value = PLUGIN_BYTE_OK;
}
else
{
plugin_return_value = PLUGIN_BYTE_ERROR;
}
break;
}
case CMD_SET_FONT :
{
usbPrintf_P(PSTR("set font file %d\n"), msg->body.data[0]);
oledSetFont(msg->body.data[0]);
if (datalen > 1) {
usbPrintf_P(PSTR("testing string \"%s\"\n"), (char *)&msg->body.data[1]);
oledFlipBuffers(0,0);
oledWriteActiveBuffer();
oledClear();
oledPutstr((char *)&msg->body.data[1]);
}
return;
}
case CMD_STACK_FREE:
usbPutstr("Stack Free ");
int_to_string(stackFree(),stack_str);
usbPutstr(stack_str);
usbPutstr(" bytes\n");
return;
#endif
default : return;
}
usbSendMessage(datacmd, 1, &plugin_return_value);
}
