int main(int argc, char **argv)
{
#if defined(__linux__) || (defined(__APPLE__) && defined(__MACH__))
//Lower the process priority on linux and mac.
setpriority(PRIO_PROCESS, 0, 10);
#endif
signal(SIGFPE, signal_FPE);
GCodeExport gcode;
ConfigSettings config;
int fileNr = 0;
config.filamentDiameter = 2890;
config.filamentFlow = 100;
config.initialLayerThickness = 300;
config.layerThickness = 100;
config.extrusionWidth = 400;
config.insetCount = 2;
config.downSkinCount = 6;
config.upSkinCount = 6;
config.initialSpeedupLayers = 4;
config.initialLayerSpeed = 20;
config.printSpeed = 50;
config.infillSpeed = 50;
config.moveSpeed = 200;
config.fanFullOnLayerNr = 2;
config.skirtDistance = 6000;
config.skirtLineCount = 1;
config.skirtMinLength = 0;
config.sparseInfillLineDistance = 100 * config.extrusionWidth / 20;
config.infillOverlap = 15;
config.objectPosition.X = 102500;
config.objectPosition.Y = 102500;
config.objectSink = 0;
config.supportAngle = -1;
config.supportEverywhere = 0;
config.supportLineDistance = config.sparseInfillLineDistance;
config.supportExtruder = -1;
config.supportXYDistance = 700;
config.supportZDistance = 150;
config.retractionAmount = 4500;
config.retractionSpeed = 45;
config.retractionAmountExtruderSwitch = 14500;
config.retractionMinimalDistance = 1500;
config.minimalExtrusionBeforeRetraction = 100;
config.enableCombing = 1;
config.multiVolumeOverlap = 0;
config.minimalLayerTime = 5;
config.minimalFeedrate = 10;
config.coolHeadLift = 1;
config.fanSpeedMin = 100;
config.fanSpeedMax = 100;
config.raftMargin = 5000;
config.raftLineSpacing = 1000;
config.raftBaseThickness = 0;
config.raftBaseLinewidth = 0;
config.raftInterfaceThickness = 0;
config.raftInterfaceLinewidth = 0;
config.spiralizeMode = 0;
config.fixHorrible = 0;
config.gcodeFlavor = GCODE_FLAVOR_REPRAP;
config.startCode =
"M109 S210 ;Heatup to 210C\n"
"G21 ;metric values\n"
"G90 ;absolute positioning\n"
"G28 ;Home\n"
"G1 Z15.0 F300 ;move the platform down 15mm\n"
"G92 E0 ;zero the extruded length\n"
"G1 F200 E5 ;extrude 5mm of feed stock\n"
"G92 E0 ;zero the extruded length again\n";
config.endCode =
"M104 S0 ;extruder heater off\n"
"M140 S0 ;heated bed heater off (if you have it)\n"
"G91 ;relative positioning\n"
"G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure\n"
"G1 Z+0.5 E-5 X-20 Y-20 F9000 ;move Z up a bit and retract filament even more\n"
"G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way\n"
"M84 ;steppers off\n"
"G90 ;absolute positioning\n";
fprintf(stderr,"Cura_SteamEngine version %s\n", VERSION);
for(int argn = 1; argn < argc; argn++)
{
char* str = argv[argn];
if (str[0] == '-')
{
for(str++; *str; str++)
{
switch(*str)
{
case 'h':
print_usage();
exit(1);
case 'v':
verbose_level++;
break;
case 'b':
argn++;
binaryMeshBlob = fopen(argv[argn], "rb");
break;
case 'o':
argn++;
gcode.setFilename(argv[argn]);
if (!gcode.isValid())
{
logError("Failed to open %s for output.\n", argv[argn]);
exit(1);
}
break;
case 's':
{
argn++;
char* valuePtr = strchr(argv[argn], '=');
if (valuePtr)
{
*valuePtr++ = '\0';
if (!config.setSetting(argv[argn], valuePtr))
printf("Setting found: %s %s\n", argv[argn], valuePtr);
}
}
break;
case 'm':
argn++;
sscanf(argv[argn], "%lf,%lf,%lf,%lf,%lf,%lf,%lf,%lf,%lf",
&config.matrix.m[0][0], &config.matrix.m[0][1], &config.matrix.m[0][2],
&config.matrix.m[1][0], &config.matrix.m[1][1], &config.matrix.m[1][2],
&config.matrix.m[2][0], &config.matrix.m[2][1], &config.matrix.m[2][2]);
break;
default:
logError("Unknown option: %c\n", *str);
break;
}
}
} else {
if (!gcode.isValid())
{
logError("No output file specified\n");
return 1;
}
gcode.addComment("Generated with Cura_SteamEngine %s", VERSION);
processFile(argv[argn], config, gcode, fileNr == 0);
fileNr ++;
}
}
if (gcode.isValid())
{
gcode.addFanCommand(0);
gcode.setZ(maxObjectHeight + 5000);
gcode.addMove(gcode.getPositionXY(), config.moveSpeed, 0);
gcode.addCode(config.endCode);
log("Print time: %d\n", int(gcode.getTotalPrintTime()));
log("Filament: %d\n", int(gcode.getTotalFilamentUsed()));
if (gcode.getFlavor() == GCODE_FLAVOR_ULTIGCODE)
{
char numberString[16];
sprintf(numberString, "%d", int(gcode.getTotalPrintTime()));
gcode.replaceTagInStart("<__TIME__>", numberString);
sprintf(numberString, "%d", int(gcode.getTotalFilamentUsed()));
gcode.replaceTagInStart("<FILAMENT>", numberString);
}
}
}
