/**
* @brief ADC MSP Initialization
* This function configures the hardware resources used in this example:
* - Peripheral's clock enable
* - Peripheral's GPIO Configuration
* @param hadc: ADC handle pointer
* @retval None
*/
void HAL_ADC_MspInit(ADC_HandleTypeDef *hadc)
{
GPIO_InitTypeDef GPIO_InitStruct;
/*##-1- Enable peripherals and GPIO Clocks #################################*/
/* Enable GPIO clock */
ADCx_CHANNEL_GPIO_CLK_ENABLE();
/* ADC3 Periph clock enable */
ADCx_CLK_ENABLE();
/*##-2- Configure peripheral GPIO ##########################################*/
/* ADC Channel GPIO pin configuration */
GPIO_InitStruct.Pin = ADCx_CHANNEL_DIFF_HIGH;
GPIO_InitStruct.Mode = GPIO_MODE_ANALOG;
GPIO_InitStruct.Pull = GPIO_NOPULL;
HAL_GPIO_Init(ADCx_CHANNEL_DIFF_HIGH_GPIO_PORT, &GPIO_InitStruct);
GPIO_InitStruct.Pin = ADCx_CHANNEL_DIFF_LOW;
HAL_GPIO_Init(ADCx_CHANNEL_DIFF_LOW_GPIO_PORT, &GPIO_InitStruct);
/*##-3- Configure the NVIC #################################################*/
/* NVIC configuration for ADC interrupt */
/* Priority: high-priority */
HAL_NVIC_SetPriority(ADC1_2_IRQn, 0, 0);
HAL_NVIC_EnableIRQ(ADC1_2_IRQn);
}
STATIC void adc_wait_for_eoc_or_timeout(int32_t timeout) {
uint32_t tickstart = HAL_GetTick();
#if defined(STM32F4) || defined(STM32F7)
while ((ADCx->SR & ADC_FLAG_EOC) != ADC_FLAG_EOC) {
#elif defined(STM32F0) || defined(STM32H7) || defined(STM32L4)
while (READ_BIT(ADCx->ISR, ADC_FLAG_EOC) != ADC_FLAG_EOC) {
#else
#error Unsupported processor
#endif
if (((HAL_GetTick() - tickstart ) > timeout)) {
break; // timeout
}
}
}
STATIC void adcx_clock_enable(void) {
#if defined(STM32F0) || defined(STM32F4) || defined(STM32F7)
ADCx_CLK_ENABLE();
#elif defined(STM32H7)
__HAL_RCC_ADC3_CLK_ENABLE();
__HAL_RCC_ADC_CONFIG(RCC_ADCCLKSOURCE_CLKP);
#elif defined(STM32L4)
__HAL_RCC_ADC_CLK_ENABLE();
#else
#error Unsupported processor
#endif
}
STATIC void adc_init_single(pyb_obj_adc_t *adc_obj) {
if (!IS_ADC_CHANNEL(adc_obj->channel)) {
return;
}
if (adc_obj->channel < ADC_NUM_GPIO_CHANNELS) {
// Channels 0-16 correspond to real pins. Configure the GPIO pin in
// ADC mode.
const pin_obj_t *pin = pin_adc1[adc_obj->channel];
GPIO_InitTypeDef GPIO_InitStructure;
GPIO_InitStructure.Pin = pin->pin_mask;
GPIO_InitStructure.Mode = GPIO_MODE_ANALOG;
GPIO_InitStructure.Pull = GPIO_NOPULL;
HAL_GPIO_Init(pin->gpio, &GPIO_InitStructure);
}
ADCx_CLK_ENABLE();
ADC_HandleTypeDef *adcHandle = &adc_obj->handle;
adcHandle->Instance = ADCx;
adcHandle->Init.ClockPrescaler = ADC_CLOCKPRESCALER_PCLK_DIV2;
adcHandle->Init.Resolution = ADC_RESOLUTION12b;
adcHandle->Init.ScanConvMode = DISABLE;
adcHandle->Init.ContinuousConvMode = DISABLE;
adcHandle->Init.DiscontinuousConvMode = DISABLE;
adcHandle->Init.NbrOfDiscConversion = 0;
adcHandle->Init.ExternalTrigConvEdge = ADC_EXTERNALTRIGCONVEDGE_NONE;
adcHandle->Init.ExternalTrigConv = ADC_EXTERNALTRIGCONV_T1_CC1;
adcHandle->Init.DataAlign = ADC_DATAALIGN_RIGHT;
adcHandle->Init.NbrOfConversion = 1;
adcHandle->Init.DMAContinuousRequests = DISABLE;
adcHandle->Init.EOCSelection = DISABLE;
HAL_ADC_Init(adcHandle);
}
/**
* @brief ADC MSP Initialization
* This function configures the hardware resources used in this example:
* - Peripheral's clock enable
* - Peripheral's GPIO Configuration
* @param huart: UART handle pointer
* @retval None
*/
void HAL_ADC_MspInit(ADC_HandleTypeDef* hadc)
{
GPIO_InitTypeDef GPIO_InitStruct;
/*##-1- Enable peripherals and GPIO Clocks #################################*/
/* ADC3 Periph clock enable */
ADCx_CLK_ENABLE();
/* Enable GPIO clock ****************************************/
ADCx_REG_CHANNEL_GPIO_CLK_ENABLE();
ADCx_INJ_CHANNEL_GPIO_CLK_ENABLE();
/*##-2- Configure peripheral GPIO ##########################################*/
/* ADC1 Channel11 GPIO pin configuration */
GPIO_InitStruct.Pin = ADCx_REG_CHANNEL_PIN;
GPIO_InitStruct.Mode = GPIO_MODE_ANALOG;
GPIO_InitStruct.Pull = GPIO_NOPULL;
HAL_GPIO_Init(ADCx_REG_CHANNEL_GPIO_PORT, &GPIO_InitStruct);
/* ADC1 Channel12 GPIO pin configuration */
GPIO_InitStruct.Pin = ADCx_INJ_CHANNEL_PIN;
GPIO_InitStruct.Mode = GPIO_MODE_ANALOG;
GPIO_InitStruct.Pull = GPIO_NOPULL;
HAL_GPIO_Init(ADCx_INJ_CHANNEL_GPIO_PORT, &GPIO_InitStruct);
/*##-3- Configure the NVIC #################################################*/
/* NVIC configuration for conversion complete complete interrupt */
HAL_NVIC_SetPriority(ADCx_IRQn, 15, 0);
HAL_NVIC_EnableIRQ(ADCx_IRQn);
}
/*****************************************************************
* ADC MSP initialization
*
* This function configures the hardware resources used in this example:
* - Enable clock of ADC peripheral
* - Configure the GPIO associated to the peripheral channels
* - Configure the DMA associated to the peripheral
* - Configure the NVIC associated to the peripheral interruptions
* @param hadc: ADC handle pointer
* @retval None
*/
void HAL_ADC_MspInit (ADC_HandleTypeDef *hadc)
{
GPIO_InitTypeDef GPIO_InitStruct;
DMA_HandleTypeDef DmaHandle;
/*##-1- Enable peripherals and GPIO Clocks ###################*/
/* Enable clock of GPIO associated to the peripheral channels */
ADCx_CHANNELa_GPIO_CLK_ENABLE();
/* Enable clock of ADCx peripheral */
ADCx_CLK_ENABLE();
/* ADC Periph interface clock configuration */
__HAL_RCC_ADC_CONFIG(RCC_ADCCLKSOURCE_SYSCLK);
/* Enable clock of DMA associated to the peripheral */
ADCx_DMA_CLK_ENABLE();
/*##-2- Configure peripheral GPIO ############################*/
/* Configure GPIO pin of the selected ADC channel */
GPIO_InitStruct.Pin = ADCx_CHANNELa_PIN;
GPIO_InitStruct.Mode = GPIO_MODE_ANALOG_ADC_CONTROL;
GPIO_InitStruct.Pull = GPIO_NOPULL;
HAL_GPIO_Init(ADCx_CHANNELa_GPIO_PORT, &GPIO_InitStruct);
/*##-3- Configure the DMA ####################################*/
/* Configure DMA parameters */
DmaHandle.Instance = ADCx_DMA;
DmaHandle.Init.Request = DMA_REQUEST_0;
DmaHandle.Init.Direction = DMA_PERIPH_TO_MEMORY;
DmaHandle.Init.PeriphInc = DMA_PINC_DISABLE;
DmaHandle.Init.MemInc = DMA_MINC_ENABLE;
DmaHandle.Init.PeriphDataAlignment = DMA_PDATAALIGN_HALFWORD; /* Transfer from ADC by half-word to match with ADC configuration: ADC resolution 10 or 12 bits */
DmaHandle.Init.MemDataAlignment = DMA_MDATAALIGN_HALFWORD; /* Transfer to memory by half-word to match with buffer variable type: half-word */
DmaHandle.Init.Mode = DMA_CIRCULAR; /* DMA in circular mode to match with ADC configuration: DMA continuous requests */
DmaHandle.Init.Priority = DMA_PRIORITY_HIGH;
/* Deinitialize & Initialize the DMA for new transfer */
HAL_DMA_DeInit(&DmaHandle);
HAL_DMA_Init(&DmaHandle);
/* Associate the initialized DMA handle to the ADC handle */
__HAL_LINKDMA(hadc, DMA_Handle, DmaHandle);
/*##-4- Configure the NVIC #########################################*/
/* NVIC configuration for DMA interrupt (transfer completion or error) */
/* Priority: high-priority */
HAL_NVIC_SetPriority(ADCx_DMA_IRQn, 1, 0);
HAL_NVIC_EnableIRQ(ADCx_DMA_IRQn);
/* NVIC configuration for ADC interrupt */
/* Priority: high-priority */
HAL_NVIC_SetPriority(ADCx_IRQn, 0, 0);
HAL_NVIC_EnableIRQ(ADCx_IRQn);
}
adc::adc (void)
{
GPIO_InitTypeDef GPIO_InitStruct;
/*##-1- Enable peripherals and GPIO Clocks #################################*/
/* ADC3 Periph clock enable */
ADCx_CLK_ENABLE()
;
/* Enable GPIO clock ****************************************/
ADCx_CHANNEL_GPIO_CLK_ENABLE()
;
/*##-2- Configure peripheral GPIO ##########################################*/
/* ADC3 Channel8 GPIO pin configuration */
GPIO_InitStruct.Pin = ADCx_CHANNEL_PIN;
GPIO_InitStruct.Mode = GPIO_MODE_ANALOG;
GPIO_InitStruct.Pull = GPIO_NOPULL;
HAL_GPIO_Init (ADCx_CHANNEL_GPIO_PORT, &GPIO_InitStruct);
/*##-3- Configure the NVIC #################################################*/
/* NVIC configuration for DMA transfer complete interrupt (USART1_TX) */
HAL_NVIC_SetPriority (ADCx_IRQn, 15, 0);
HAL_NVIC_EnableIRQ (ADCx_IRQn);
ADC_ChannelConfTypeDef sConfig;
/*##-1- Configure the ADC peripheral #######################################*/
AdcHandle.Instance = ADCx;
AdcHandle.Init.ClockPrescaler = ADC_CLOCKPRESCALER_PCLK_DIV8;
AdcHandle.Init.Resolution = ADC_RESOLUTION_12B;
AdcHandle.Init.ScanConvMode = DISABLE;
AdcHandle.Init.ContinuousConvMode = ENABLE;
AdcHandle.Init.DiscontinuousConvMode = DISABLE;
AdcHandle.Init.NbrOfDiscConversion = 0;
AdcHandle.Init.ExternalTrigConvEdge = ADC_EXTERNALTRIGCONVEDGE_NONE;
AdcHandle.Init.ExternalTrigConv = ADC_EXTERNALTRIGCONV_T1_CC1;
AdcHandle.Init.DataAlign = ADC_DATAALIGN_RIGHT;
AdcHandle.Init.NbrOfConversion = 1;
AdcHandle.Init.DMAContinuousRequests = DISABLE;
AdcHandle.Init.EOCSelection = DISABLE;
if (HAL_ADC_Init (&AdcHandle) != HAL_OK)
asm("bkpt 0");
/*##-2- Configure ADC regular channel ######################################*/
sConfig.Channel = ADCx_CHANNEL;
sConfig.Rank = 1;
sConfig.SamplingTime = ADC_SAMPLETIME_3CYCLES;
sConfig.Offset = 0;
if (HAL_ADC_ConfigChannel (&AdcHandle, &sConfig) != HAL_OK)
asm("bkpt 0");
/*##-3- Start the conversion process and enable interrupt ##################*/
if (HAL_ADC_Start_IT (&AdcHandle) != HAL_OK)
asm("bkpt 0");
}
/**
* @brief ADC MSP Initialization
* This function configures the hardware resources used in this example:
* - Peripheral's clock enable
* - Peripheral's GPIO Configuration
* @param huart: UART handle pointer
* @retval None
*/
void HAL_ADC_MspInit(ADC_HandleTypeDef* hadc)
{
GPIO_InitTypeDef GPIO_InitStruct;
static DMA_HandleTypeDef hdma_adc;
/*##-1- Enable peripherals and GPIO Clocks #################################*/
/* Enable GPIO clock */
ADCxyz_CHANNEL_GPIO_CLK_ENABLE();
/* ADCx Periph clock enable */
ADCx_CLK_ENABLE();
/* ADCy Periph clock enable */
ADCy_CLK_ENABLE();
/* ADCz Periph clock enable */
ADCz_CLK_ENABLE();
/* Enable DMA2 clock */
DMAxyz_CLK_ENABLE();
/*##-2- Configure peripheral GPIO ##########################################*/
/* ADCx and ADCy Channel12 GPIO pin configuration */
GPIO_InitStruct.Pin = ADCxyz_CHANNEL_PIN;
GPIO_InitStruct.Mode = GPIO_MODE_ANALOG;
GPIO_InitStruct.Pull = GPIO_NOPULL;
HAL_GPIO_Init(ADCxyz_CHANNEL_GPIO_PORT, &GPIO_InitStruct);
/*##-3- Configure the DMA streams ##########################################*/
/* Set the parameters to be configured */
hdma_adc.Instance = ADCxyz_DMA_STREAM;
hdma_adc.Init.Channel = ADCxyz_DMA_CHANNEL;
hdma_adc.Init.Direction = DMA_PERIPH_TO_MEMORY;
hdma_adc.Init.PeriphInc = DMA_PINC_DISABLE;
hdma_adc.Init.MemInc = DMA_MINC_ENABLE;
hdma_adc.Init.PeriphDataAlignment = DMA_PDATAALIGN_WORD;
hdma_adc.Init.MemDataAlignment = DMA_MDATAALIGN_WORD;
hdma_adc.Init.Mode = DMA_CIRCULAR;
hdma_adc.Init.Priority = DMA_PRIORITY_HIGH;
hdma_adc.Init.FIFOMode = DMA_FIFOMODE_DISABLE;
hdma_adc.Init.FIFOThreshold = DMA_FIFO_THRESHOLD_HALFFULL;
hdma_adc.Init.MemBurst = DMA_MBURST_SINGLE;
hdma_adc.Init.PeriphBurst = DMA_PBURST_SINGLE;
HAL_DMA_Init(&hdma_adc);
/* Associate the initialized DMA handle to the the UART handle */
__HAL_LINKDMA(hadc, DMA_Handle, hdma_adc);
/*##-4- Configure the NVIC for DMA #########################################*/
/* NVIC configuration for DMA transfer complete interrupt */
HAL_NVIC_SetPriority(ADCxyz_DMA_IRQn, 0, 0);
HAL_NVIC_EnableIRQ(ADCxyz_DMA_IRQn);
}
/**
* @brief ADC MSP Initialization
* This function configures the hardware resources used in this example:
* - Peripheral's clock enable
* - Peripheral's GPIO Configuration
* @param hadc: ADC handle pointer
* @retval None
*/
void HAL_ADC_MspInit(ADC_HandleTypeDef *hadc)
{
GPIO_InitTypeDef GPIO_InitStruct;
static DMA_HandleTypeDef DmaHandle;
/*##-1- Enable peripherals and GPIO Clocks #################################*/
/* Enable GPIO clock */
ADCx_CHANNEL_GPIO_CLK_ENABLE();
/* ADC1 Periph clock enable */
ADCx_CLK_ENABLE();
/* Enable DMA1 clock */
__HAL_RCC_DMA1_CLK_ENABLE();
/*##-2- Configure peripheral GPIO ##########################################*/
/* ADC1 Channel9 GPIO pin configuration */
GPIO_InitStruct.Pin = ADCx_CHANNEL_PIN;
GPIO_InitStruct.Mode = GPIO_MODE_ANALOG;
GPIO_InitStruct.Pull = GPIO_NOPULL;
HAL_GPIO_Init(ADCx_CHANNEL_GPIO_PORT, &GPIO_InitStruct);
/*##- 3- Configure DMA #####################################################*/
/*********************** Configure DMA parameters ***************************/
DmaHandle.Instance = DMA1_Channel1;
DmaHandle.Init.Direction = DMA_PERIPH_TO_MEMORY;
DmaHandle.Init.PeriphInc = DMA_PINC_DISABLE;
DmaHandle.Init.MemInc = DMA_MINC_ENABLE;
DmaHandle.Init.PeriphDataAlignment = DMA_PDATAALIGN_WORD;
DmaHandle.Init.MemDataAlignment = DMA_MDATAALIGN_WORD;
DmaHandle.Init.Mode = DMA_CIRCULAR;
DmaHandle.Init.Priority = DMA_PRIORITY_HIGH;
/* Deinitialize & Initialize the DMA for new transfer */
HAL_DMA_DeInit(&DmaHandle);
HAL_DMA_Init(&DmaHandle);
/* Associate the initialized DMA handle to the the ADC handle */
__HAL_LINKDMA(hadc, DMA_Handle, DmaHandle);
/*##-4- Configure the NVIC for DMA #########################################*/
/* NVIC configuration for DMA transfer complete interrupt */
HAL_NVIC_SetPriority(ADCx_DMA_IRQn, 5, 0);
HAL_NVIC_EnableIRQ(ADCx_DMA_IRQn);
}
/**
* @brief ADC MSP Initialization
* This function configures the hardware resources used in this example:
* - Peripheral's clock enable
* - Peripheral's GPIO Configuration
* @param hadc: ADC handle pointer
* @retval None
*/
void HAL_ADC_MspInit(ADC_HandleTypeDef *hadc)
{
GPIO_InitTypeDef GPIO_InitStruct;
/*##-1- Enable peripherals and GPIO Clocks #################################*/
/* ADC3 Periph clock enable */
ADCx_CLK_ENABLE();
/* Enable GPIO clock ****************************************/
ADCx_CHANNEL_GPIO_CLK_ENABLE();
/*##-2- Configure peripheral GPIO ##########################################*/
/* ADC Channel GPIO pin configuration */
GPIO_InitStruct.Pin = ADCx_CHANNEL_PIN;
GPIO_InitStruct.Mode = GPIO_MODE_ANALOG;
GPIO_InitStruct.Pull = GPIO_NOPULL;
HAL_GPIO_Init(ADCx_CHANNEL_GPIO_PORT, &GPIO_InitStruct);
}
/*====================================================================================================*/
void HAL_ADC_MspInit( ADC_HandleTypeDef *hadc )
{
static DMA_HandleTypeDef DMA_HandleStruct;
GPIO_InitTypeDef GPIO_InitStruct;
RCC_PeriphCLKInitTypeDef RCC_PeriphCLKInitStruct;
/* Enable clock ******************************************************************/
ADCx_GPIO_CLK_ENABLE();
ADCx_CLK_ENABLE();
ADCx_DMA_CLK_ENABLE();
/* Enable asynchronous clock source of ADCx **************************************/
RCC_PeriphCLKInitStruct.PeriphClockSelection = RCC_PERIPHCLK_ADC12;
RCC_PeriphCLKInitStruct.Adc12ClockSelection = RCC_ADC12PLLCLK_DIV1;
HAL_RCCEx_PeriphCLKConfig(&RCC_PeriphCLKInitStruct);
/* Config GPIO ******************************************************************/
GPIO_InitStruct.Pin = ADCx_GPIO_PIN;
GPIO_InitStruct.Mode = GPIO_MODE_ANALOG;
GPIO_InitStruct.Pull = GPIO_NOPULL;
HAL_GPIO_Init(ADCx_GPIO_PORT, &GPIO_InitStruct);
/* Config DMA *****************************************************************/
DMA_HandleStruct.Instance = ADCx_DMA_CHANNEL;
DMA_HandleStruct.Init.Direction = DMA_PERIPH_TO_MEMORY;
DMA_HandleStruct.Init.PeriphInc = DMA_PINC_DISABLE;
DMA_HandleStruct.Init.MemInc = DMA_MINC_ENABLE;
DMA_HandleStruct.Init.PeriphDataAlignment = DMA_PDATAALIGN_HALFWORD;
DMA_HandleStruct.Init.MemDataAlignment = DMA_MDATAALIGN_HALFWORD;
DMA_HandleStruct.Init.Mode = DMA_CIRCULAR;
DMA_HandleStruct.Init.Priority = DMA_PRIORITY_MEDIUM;
HAL_DMA_DeInit(&DMA_HandleStruct);
HAL_DMA_Init(&DMA_HandleStruct);
__HAL_LINKDMA(hadc, DMA_Handle, DMA_HandleStruct);
/* Config NVIC *****************************************************************/
// DMA interrupt - Priority: high-priority
HAL_NVIC_SetPriority(ADCx_DMA_IRQn, 1, 0);
HAL_NVIC_EnableIRQ(ADCx_DMA_IRQn);
// ADC interrupt - Priority: high-priority
HAL_NVIC_SetPriority(ADCx_IRQn, 0, 0);
HAL_NVIC_EnableIRQ(ADCx_IRQn);
}
/**
* @brief ADC MSP Initialization
* This function configures the hardware resources used in this example:
* - Configuration of peripheral clock
* - Configuration of GPIO associated to the peripheral channels
* - Configuration of DMA
* - Configuration of interruptions
* @param huart: UART handle pointer
* @retval None
*/
void HAL_ADC_MspInit(ADC_HandleTypeDef *hadc)
{
GPIO_InitTypeDef GPIO_InitStruct;
static DMA_HandleTypeDef hdma_adc;
/*##-1- Enable peripherals and GPIO Clocks #################################*/
/* Enable GPIO clock */
ADCxy_CHANNEL_GPIO_CLK_ENABLE();
/* ADCx Periph clock enable */
ADCx_CLK_ENABLE();
/* ADCy Periph clock enable */
ADCy_CLK_ENABLE();
/* Enable DMA clock */
DMAxy_CLK_ENABLE();
/*##-2- Configure peripheral GPIO ##########################################*/
/* ADCx and ADCy Channel GPIO pin configuration */
GPIO_InitStruct.Pin = ADCxy_CHANNEL_PIN;
GPIO_InitStruct.Mode = GPIO_MODE_ANALOG;
GPIO_InitStruct.Pull = GPIO_NOPULL;
HAL_GPIO_Init(ADCxy_CHANNEL_GPIO_PORT, &GPIO_InitStruct);
/*##-3- Configure the DMA channels ##########################################*/
/* Set the parameters to be configured */
hdma_adc.Instance = ADCxy_DMA_STREAM; /* DMA channel of ADC1 (ADC master) */
hdma_adc.Init.Direction = DMA_PERIPH_TO_MEMORY;
hdma_adc.Init.PeriphInc = DMA_PINC_DISABLE;
hdma_adc.Init.MemInc = DMA_MINC_ENABLE;
hdma_adc.Init.PeriphDataAlignment = DMA_PDATAALIGN_HALFWORD; /* Transfer by half-word to match with ADC resolution 6 or 8 bits */
hdma_adc.Init.MemDataAlignment = DMA_MDATAALIGN_HALFWORD; /* Transfer by half-word to match with ADC resolution 6 or 8 bits */
hdma_adc.Init.Mode = DMA_CIRCULAR; /* DMA in circular mode to match with ADC-DMA continuous requests */
hdma_adc.Init.Priority = DMA_PRIORITY_HIGH;
HAL_DMA_Init(&hdma_adc);
/* Associate the initialized DMA handle to the the ADC handle */
__HAL_LINKDMA(hadc, DMA_Handle, hdma_adc);
/*##-4- Configure the NVIC for DMA #########################################*/
/* NVIC configuration for DMA transfer complete interrupt */
HAL_NVIC_SetPriority(ADCxy_DMA_IRQn, 0, 0);
HAL_NVIC_EnableIRQ(ADCxy_DMA_IRQn);
}
/**
* @brief ADC MSP initialization
* This function configures the hardware resources used in this example:
* - Enable clock of ADC peripheral
* - Configure the GPIO associated to the peripheral channels
* - Configure the DMA associated to the peripheral
* - Configure the NVIC associated to the peripheral interruptions
* @param hadc: ADC handle pointer
* @retval None
*/
void HAL_ADC_MspInit(ADC_HandleTypeDef *hadc)
{
GPIO_InitTypeDef GPIO_InitStruct;
RCC_OscInitTypeDef RCC_OscInitStructure;
/*##-1- Enable peripherals and GPIO Clocks #################################*/
/* Enable clock of GPIO associated to the peripheral channels */
ADCx_CHANNELa_GPIO_CLK_ENABLE();
/* Enable clock of ADCx peripheral */
ADCx_CLK_ENABLE();
/* Note: STM32L0 ADC is using a dedicated asynchronous clock derived */
/* from HSI RC oscillator 16MHz. */
/* The clock source has to be enabled at RCC top level using function */
/* "HAL_RCC_OscConfig()" (see comments in stm32l0_hal_adc.c header) */
/* Enable asynchronous clock source of ADCx */
HAL_RCC_GetOscConfig(&RCC_OscInitStructure);
RCC_OscInitStructure.OscillatorType = RCC_OSCILLATORTYPE_HSI;
RCC_OscInitStructure.HSICalibrationValue = RCC_HSICALIBRATION_DEFAULT;
RCC_OscInitStructure.HSIState = RCC_HSI_ON;
HAL_RCC_OscConfig(&RCC_OscInitStructure);
/*##-2- Configure peripheral GPIO ##########################################*/
/* ADCx Channel GPIO pin configuration */
GPIO_InitStruct.Pin = ADCx_CHANNELa_PIN;
GPIO_InitStruct.Mode = GPIO_MODE_ANALOG;
GPIO_InitStruct.Pull = GPIO_NOPULL;
HAL_GPIO_Init(ADCx_CHANNELa_GPIO_PORT, &GPIO_InitStruct);
/*##-3- Configure the DMA ##################################################*/
/* ADC does not use DMA in this ADC example */
/*##-4- Configure the NVIC #################################################*/
/* NVIC configuration for ADC interrupt */
/* Priority: high-priority */
HAL_NVIC_SetPriority(ADCx_IRQn, 0, 0);
HAL_NVIC_EnableIRQ(ADCx_IRQn);
}
/**
* @brief ADC MSP initialization
* This function configures the hardware resources used in this example:
* - Enable clock of ADC peripheral
* - Configure the GPIO associated to the peripheral channels
* - Configure the DMA associated to the peripheral
* - Configure the NVIC associated to the peripheral interruptions
* @param hadc: ADC handle pointer
* @retval None
*/
void HAL_ADC_MspInit(ADC_HandleTypeDef *hadc)
{
GPIO_InitTypeDef GPIO_InitStruct;
static DMA_HandleTypeDef DmaHandle;
RCC_PeriphCLKInitTypeDef PeriphClkInit;
/*##-1- Enable peripherals and GPIO Clocks #################################*/
/* Enable clock of GPIO associated to the peripheral channels */
ADCx_CHANNELa_GPIO_CLK_ENABLE();
/* Enable clock of ADCx peripheral */
ADCx_CLK_ENABLE();
/* Note: In case of usage of asynchronous clock derived from ADC dedicated */
/* PLL 72MHz, with ADC setting */
/* "AdcHandle.Init.ClockPrescaler = ADC_CLOCK_ASYNC_DIV1", */
/* the clock source has to be enabled at RCC top level using macro */
/* "__HAL_RCC_ADC12_CONFIG(RCC_ADC12PLLCLK_DIV1)" or function */
/* "HAL_RCCEx_PeriphCLKConfig()" (refer to comments in file */
/* "stm32f3_hal_adc.c_ex" header). */
/* Enable asynchronous clock source of ADCx */
PeriphClkInit.PeriphClockSelection = RCC_PERIPHCLK_ADC12;
PeriphClkInit.Adc12ClockSelection = RCC_ADC12PLLCLK_DIV1;
HAL_RCCEx_PeriphCLKConfig(&PeriphClkInit);
/* Enable clock of DMA associated to the peripheral */
ADCx_DMA_CLK_ENABLE();
/*##-2- Configure peripheral GPIO ##########################################*/
/* Configure GPIO pin of the selected ADC channel */
GPIO_InitStruct.Pin = ADCx_CHANNELa_PIN;
GPIO_InitStruct.Mode = GPIO_MODE_ANALOG;
GPIO_InitStruct.Pull = GPIO_NOPULL;
HAL_GPIO_Init(ADCx_CHANNELa_GPIO_PORT, &GPIO_InitStruct);
/*##-3- Configure the DMA ##################################################*/
/* Configure DMA parameters */
DmaHandle.Instance = ADCx_DMA;
DmaHandle.Init.Direction = DMA_PERIPH_TO_MEMORY;
DmaHandle.Init.PeriphInc = DMA_PINC_DISABLE;
DmaHandle.Init.MemInc = DMA_MINC_ENABLE;
DmaHandle.Init.PeriphDataAlignment = DMA_PDATAALIGN_HALFWORD; /* Transfer from ADC by half-word to match with ADC configuration: ADC resolution 10 or 12 bits */
DmaHandle.Init.MemDataAlignment = DMA_MDATAALIGN_HALFWORD; /* Transfer to memory by half-word to match with buffer variable type: half-word */
DmaHandle.Init.Mode = DMA_CIRCULAR; /* DMA in circular mode to match with ADC configuration: DMA continuous requests */
DmaHandle.Init.Priority = DMA_PRIORITY_HIGH;
/* Deinitialize & Initialize the DMA for new transfer */
HAL_DMA_DeInit(&DmaHandle);
HAL_DMA_Init(&DmaHandle);
/* Associate the initialized DMA handle to the ADC handle */
__HAL_LINKDMA(hadc, DMA_Handle, DmaHandle);
/*##-4- Configure the NVIC #################################################*/
/* NVIC configuration for DMA interrupt (transfer completion or error) */
/* Priority: high-priority */
HAL_NVIC_SetPriority(ADCx_DMA_IRQn, 1, 0);
HAL_NVIC_EnableIRQ(ADCx_DMA_IRQn);
/* NVIC configuration for ADC interrupt */
/* Priority: high-priority */
HAL_NVIC_SetPriority(ADCx_IRQn, 0, 0);
HAL_NVIC_EnableIRQ(ADCx_IRQn);
}
/**
* @brief ADC MSP initialization
* This function configures the hardware resources used in this example:
* - Enable clock of ADC peripheral
* - Configure the GPIO associated to the peripheral channels
* - Configure the DMA associated to the peripheral
* - Configure the NVIC associated to the peripheral interruptions
* @param hadc: ADC handle pointer
* @retval None
*/
void HAL_ADC_MspInit(ADC_HandleTypeDef *hadc)
{
GPIO_InitTypeDef GPIO_InitStruct;
static DMA_HandleTypeDef DmaHandle;
RCC_OscInitTypeDef RCC_OscInitStructure;
/*##-1- Enable peripherals and GPIO Clocks #################################*/
/* Enable clock of GPIO associated to the peripheral channels */
ADCx_CHANNELa_GPIO_CLK_ENABLE();
/* Enable clock of ADCx peripheral */
ADCx_CLK_ENABLE();
/* Note: In case of usage of asynchronous clock derived from ADC dedicated */
/* HSI RC oscillator 14MHz, with ADC setting */
/* "AdcHandle.Init.ClockPrescaler = ADC_CLOCK_ASYNC", */
/* the clock source has to be enabled at RCC top level using function */
/* "HAL_RCC_OscConfig()" (see comments in stm32l1_hal_adc.c header) */
/* Enable asynchronous clock source of ADCx */
/* (place oscillator HSI14 under control of the ADC) */
HAL_RCC_GetOscConfig(&RCC_OscInitStructure);
RCC_OscInitStructure.OscillatorType = RCC_OSCILLATORTYPE_HSI14;
RCC_OscInitStructure.HSI14CalibrationValue = RCC_HSI14CALIBRATION_DEFAULT;
RCC_OscInitStructure.HSI14State = RCC_HSI14_ADC_CONTROL;
HAL_RCC_OscConfig(&RCC_OscInitStructure);
/* Enable clock of DMA associated to the peripheral */
ADCx_DMA_CLK_ENABLE();
/*##-2- Configure peripheral GPIO ##########################################*/
/* ADCx Channel GPIO pin configuration */
GPIO_InitStruct.Pin = ADCx_CHANNELa_PIN;
GPIO_InitStruct.Mode = GPIO_MODE_ANALOG;
GPIO_InitStruct.Pull = GPIO_NOPULL;
HAL_GPIO_Init(ADCx_CHANNELa_GPIO_PORT, &GPIO_InitStruct);
/*##-3- Configure the DMA ##################################################*/
/* Configure DMA parameters */
DmaHandle.Instance = ADCx_DMA;
DmaHandle.Init.Direction = DMA_PERIPH_TO_MEMORY;
DmaHandle.Init.PeriphInc = DMA_PINC_DISABLE;
DmaHandle.Init.MemInc = DMA_MINC_ENABLE;
DmaHandle.Init.PeriphDataAlignment = DMA_PDATAALIGN_HALFWORD; /* Transfer from ADC by half-word to match with ADC resolution 10 or 12 bits */
DmaHandle.Init.MemDataAlignment = DMA_MDATAALIGN_HALFWORD; /* Transfer to memory by half-word to match with buffer variable type: half-word */
DmaHandle.Init.Mode = DMA_CIRCULAR;
DmaHandle.Init.Priority = DMA_PRIORITY_HIGH;
/* Deinitialize & Initialize the DMA for new transfer */
HAL_DMA_DeInit(&DmaHandle);
HAL_DMA_Init(&DmaHandle);
/* Associate the initialized DMA handle to the ADC handle */
__HAL_LINKDMA(hadc, DMA_Handle, DmaHandle);
/*##-4- Configure the NVIC #################################################*/
/* NVIC configuration for DMA interrupt (transfer completion or error) */
/* Priority: high-priority */
HAL_NVIC_SetPriority(ADCx_DMA_IRQn, 1, 0);
HAL_NVIC_EnableIRQ(ADCx_DMA_IRQn);
/* NVIC configuration for ADC interrupt */
/* Priority: high-priority */
HAL_NVIC_SetPriority(ADCx_IRQn, 0, 0);
HAL_NVIC_EnableIRQ(ADCx_IRQn);
}
void ADC_Config( void )
{
DMA_InitTypeDef DMA_InitStruct;
ADC_InitTypeDef ADC_InitStruct;
ADC_CommonInitTypeDef ADC_CommonInitStruct;
GPIO_InitTypeDef GPIO_InitStruct;
/* ADC Clk *******************************************************************/
RCC_ADCCLKConfig(RCC_ADC12PLLCLK_Div2);
ADCx_CLK_ENABLE();
ADCx_DMA_CLK_ENABLE();
/* ADC Pin *******************************************************************/
GPIO_InitStruct.GPIO_Mode = GPIO_Mode_AN;
GPIO_InitStruct.GPIO_PuPd = GPIO_PuPd_NOPULL;
GPIO_InitStruct.GPIO_Pin = ADCxP_PIN;
GPIO_Init(ADCxP_GPIO_PORT, &GPIO_InitStruct);
GPIO_InitStruct.GPIO_Pin = ADCxN_PIN;
GPIO_Init(ADCxN_GPIO_PORT, &GPIO_InitStruct);
/* ADC DMA *******************************************************************/
DMA_DeInit(ADCx_DMA_CHANNEL);
DMA_InitStruct.DMA_PeripheralBaseAddr = ADCx_DR_ADDRESS;
DMA_InitStruct.DMA_MemoryBaseAddr = (uint32_t)ADC_DMA_ConvBuf;
DMA_InitStruct.DMA_DIR = DMA_DIR_PeripheralSRC;
DMA_InitStruct.DMA_BufferSize = ADC_BUF_CHENNAL * ADC_BUF_SIZE;
DMA_InitStruct.DMA_PeripheralInc = DMA_PeripheralInc_Disable;
DMA_InitStruct.DMA_MemoryInc = DMA_MemoryInc_Enable;
DMA_InitStruct.DMA_PeripheralDataSize = DMA_PeripheralDataSize_HalfWord;
DMA_InitStruct.DMA_MemoryDataSize = DMA_MemoryDataSize_HalfWord;
DMA_InitStruct.DMA_Mode = DMA_Mode_Circular;
DMA_InitStruct.DMA_Priority = DMA_Priority_Medium;
DMA_InitStruct.DMA_M2M = DMA_M2M_Disable;
DMA_Init(ADCx_DMA_CHANNEL, &DMA_InitStruct);
DMA_Cmd(ADCx_DMA_CHANNEL, ENABLE);
/* ADC Calibration ***********************************************************/
ADC_VoltageRegulatorCmd(ADCx, ENABLE);
delay_ms(10);
ADC_SelectCalibrationMode(ADCx, ADC_CalibrationMode_Single);
ADC_StartCalibration(ADCx);
while(ADC_GetCalibrationStatus(ADCx) != RESET);
calibrationValue = ADC_GetCalibrationValue(ADCx);
/* ADC Common Init ***********************************************************/
ADC_CommonInitStruct.ADC_Mode = ADC_Mode_Interleave; // ADC_Mode_Independent
ADC_CommonInitStruct.ADC_Clock = ADC_Clock_AsynClkMode;
ADC_CommonInitStruct.ADC_DMAAccessMode = ADC_DMAAccessMode_1;
ADC_CommonInitStruct.ADC_DMAMode = ADC_DMAMode_Circular;
ADC_CommonInitStruct.ADC_TwoSamplingDelay = 0;
ADC_CommonInit(ADCx, &ADC_CommonInitStruct);
/* ADC Init *****************************************************************/
ADC_InitStruct.ADC_ContinuousConvMode = ADC_ContinuousConvMode_Enable;
ADC_InitStruct.ADC_Resolution = ADC_Resolution_12b;
ADC_InitStruct.ADC_ExternalTrigConvEvent = ADC_ExternalTrigConvEvent_0;
ADC_InitStruct.ADC_ExternalTrigEventEdge = ADC_ExternalTrigEventEdge_None;
ADC_InitStruct.ADC_DataAlign = ADC_DataAlign_Right;
ADC_InitStruct.ADC_OverrunMode = ADC_OverrunMode_Disable;
ADC_InitStruct.ADC_AutoInjMode = ADC_AutoInjec_Disable;
ADC_InitStruct.ADC_NbrOfRegChannel = ADC_BUF_SIZE;
ADC_Init(ADCx, &ADC_InitStruct);
/* ADC Regular Config *******************************************************/
ADC_RegularChannelConfig(ADCx, ADCxP_CHANNEL, 1, ADC_SampleTime_601Cycles5);
ADC_RegularChannelConfig(ADCx, ADCxN_CHANNEL, 2, ADC_SampleTime_601Cycles5);
/* Enable & Start ***********************************************************/
ADC_DMACmd(ADCx, ENABLE);
ADC_Cmd(ADCx, ENABLE);
while(!ADC_GetFlagStatus(ADCx, ADC_FLAG_RDY));
DMA_Cmd(ADCx_DMA_CHANNEL, ENABLE);
ADC_StartConversion(ADCx);
}
/**
* @brief ADC MSP Init
* @param hadc : ADC handle
* @retval None
*/
void HAL_ADC_MspInit(ADC_HandleTypeDef *hadc)
{
GPIO_InitTypeDef GPIO_InitStruct;
static DMA_HandleTypeDef DmaHandle;
/*##-1- Enable peripherals and GPIO Clocks #################################*/
/* Enable GPIO clock ****************************************/
__HAL_RCC_GPIOA_CLK_ENABLE();
__HAL_RCC_GPIOB_CLK_ENABLE();
__HAL_RCC_GPIOC_CLK_ENABLE();
/* ADC1 Periph clock enable */
ADCx_CLK_ENABLE();
/* Enable DMA1 clock */
__HAL_RCC_DMA1_CLK_ENABLE();
/*##- 2- Configure peripheral GPIO #########################################*/
/* ADC Channel GPIO pin configuration */
GPIO_InitStruct.Pin = GPIO_PIN_2;
GPIO_InitStruct.Mode = GPIO_MODE_ANALOG;
GPIO_InitStruct.Pull = GPIO_NOPULL;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
GPIO_InitStruct.Pin = GPIO_PIN_1;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
GPIO_InitStruct.Pin = GPIO_PIN_3;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
GPIO_InitStruct.Pin = GPIO_PIN_0;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
GPIO_InitStruct.Pin = GPIO_PIN_0;
HAL_GPIO_Init(GPIOC, &GPIO_InitStruct);
GPIO_InitStruct.Pin = GPIO_PIN_1;
HAL_GPIO_Init(GPIOC, &GPIO_InitStruct);
GPIO_InitStruct.Pin = GPIO_PIN_2;
HAL_GPIO_Init(GPIOC, &GPIO_InitStruct);
GPIO_InitStruct.Pin = GPIO_PIN_3;
HAL_GPIO_Init(GPIOC, &GPIO_InitStruct);
GPIO_InitStruct.Pin = GPIO_PIN_1;
HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
/*##- 3- Configure DMA #####################################################*/
/*********************** Configure DMA parameters ***************************/
DmaHandle.Instance = DMA1_Channel1;
DmaHandle.Init.Direction = DMA_PERIPH_TO_MEMORY;
DmaHandle.Init.PeriphInc = DMA_PINC_DISABLE;
DmaHandle.Init.MemInc = DMA_MINC_ENABLE;
DmaHandle.Init.PeriphDataAlignment = DMA_PDATAALIGN_HALFWORD;
DmaHandle.Init.MemDataAlignment = DMA_MDATAALIGN_HALFWORD;
DmaHandle.Init.Mode = DMA_CIRCULAR;
DmaHandle.Init.Priority = DMA_PRIORITY_MEDIUM;
/* Deinitialize & Initialize the DMA for new transfer */
HAL_DMA_DeInit(&DmaHandle);
HAL_DMA_Init(&DmaHandle);
/* Associate the DMA handle */
__HAL_LINKDMA(hadc, DMA_Handle, DmaHandle);
/* NVIC configuration for DMA Input data interrupt */
HAL_NVIC_SetPriority(DMA1_Channel1_IRQn, 1, 0);
HAL_NVIC_EnableIRQ(DMA1_Channel1_IRQn);
/* NVIC configuration for ADC interrupt */
/* Priority: high-priority */
HAL_NVIC_SetPriority(ADC1_2_IRQn, 0, 0);
HAL_NVIC_EnableIRQ(ADC1_2_IRQn);
}
/**
* @brief ADC MSP initialization
* This function configures the hardware resources used in this example:
* - Enable clock of ADC peripheral
* - Configure the GPIO associated to the peripheral channels
* - Configure the DMA associated to the peripheral
* - Configure the NVIC associated to the peripheral interruptions
* @param hadc: ADC handle pointer
* @retval None
*/
void HAL_ADC_MspInit(ADC_HandleTypeDef *hadc)
{
GPIO_InitTypeDef GPIO_InitStruct;
static DMA_HandleTypeDef DmaHandle;
RCC_PeriphCLKInitTypeDef PeriphClkInit;
/*##-1- Enable peripherals and GPIO Clocks #################################*/
/* Enable clock of GPIO associated to the peripheral channels */
ADCx_CHANNELa_GPIO_CLK_ENABLE();
/* Enable clock of ADCx peripheral */
ADCx_CLK_ENABLE();
/* Configure ADCx clock prescaler */
/* Caution: On STM32F1, ADC clock frequency max is 14MHz (refer to device */
/* datasheet). */
/* Therefore, ADC clock prescaler must be configured in function */
/* of ADC clock source frequency to remain below this maximum */
/* frequency. */
PeriphClkInit.PeriphClockSelection = RCC_PERIPHCLK_ADC;
PeriphClkInit.AdcClockSelection = RCC_ADCPCLK2_DIV6;
HAL_RCCEx_PeriphCLKConfig(&PeriphClkInit);
/* Enable clock of DMA associated to the peripheral */
ADCx_DMA_CLK_ENABLE();
/*##-2- Configure peripheral GPIO ##########################################*/
/* Configure GPIO pin of the selected ADC channel */
GPIO_InitStruct.Pin = ADCx_CHANNELa_PIN;
GPIO_InitStruct.Mode = GPIO_MODE_ANALOG;
GPIO_InitStruct.Pull = GPIO_NOPULL;
HAL_GPIO_Init(ADCx_CHANNELa_GPIO_PORT, &GPIO_InitStruct);
/*##-3- Configure the DMA ##################################################*/
/* Configure DMA parameters */
DmaHandle.Instance = ADCx_DMA;
DmaHandle.Init.Direction = DMA_PERIPH_TO_MEMORY;
DmaHandle.Init.PeriphInc = DMA_PINC_DISABLE;
DmaHandle.Init.MemInc = DMA_MINC_ENABLE;
DmaHandle.Init.PeriphDataAlignment = DMA_PDATAALIGN_HALFWORD; /* Transfer from ADC by half-word to match with ADC configuration: ADC resolution 10 or 12 bits */
DmaHandle.Init.MemDataAlignment = DMA_MDATAALIGN_HALFWORD; /* Transfer to memory by half-word to match with buffer variable type: half-word */
DmaHandle.Init.Mode = DMA_CIRCULAR; /* DMA in circular mode to match with ADC configuration: DMA continuous requests */
DmaHandle.Init.Priority = DMA_PRIORITY_HIGH;
/* Deinitialize & Initialize the DMA for new transfer */
HAL_DMA_DeInit(&DmaHandle);
HAL_DMA_Init(&DmaHandle);
/* Associate the initialized DMA handle to the ADC handle */
__HAL_LINKDMA(hadc, DMA_Handle, DmaHandle);
/*##-4- Configure the NVIC #################################################*/
/* NVIC configuration for DMA interrupt (transfer completion or error) */
/* Priority: high-priority */
HAL_NVIC_SetPriority(ADCx_DMA_IRQn, 1, 0);
HAL_NVIC_EnableIRQ(ADCx_DMA_IRQn);
/* NVIC configuration for ADC interrupt */
/* Priority: high-priority */
HAL_NVIC_SetPriority(ADCx_IRQn, 0, 0);
HAL_NVIC_EnableIRQ(ADCx_IRQn);
}
/**
* @brief ADC MSP initialization
* This function configures the hardware resources used in this example:
* - Enable clock of ADC peripheral
* - Configure the GPIO associated to the peripheral channels
* - Configure the DMA associated to the peripheral
* - Configure the NVIC associated to the peripheral interruptions
* @param hadc: ADC handle pointer
* @retval None
*/
void HAL_ADC_MspInit(ADC_HandleTypeDef *hadc)
{
GPIO_InitTypeDef GPIO_InitStruct;
static DMA_HandleTypeDef DmaHandle;
/*##-1- Enable peripherals and GPIO Clocks #################################*/
/* Enable clock of GPIO associated to the peripheral channels */
ADCx_CHANNELa_GPIO_CLK_ENABLE();
/* Enable clock of ADCx peripheral */
ADCx_CLK_ENABLE();
/* Note: In case of usage of ADC dedicated asynchronous clock, with ADC */
/* setting "AdcHandle.Init.ClockPrescaler = ADC_CLOCK_ASYNC", */
/* the clock source has to be enabled using this macro: */
/* __HAL_RCC_ADC12_CONFIG(RCC_ADC12PLLCLK_DIV1); */
/* Enable asynchronous clock source of ADCx */
__HAL_RCC_ADC1_CONFIG(RCC_ADC1PLLCLK_DIV1);
/* Enable clock of DMA associated to the peripheral */
ADCx_DMA_CLK_ENABLE();
/*##-2- Configure peripheral GPIO ##########################################*/
/* ADCx Channel GPIO pin configuration */
GPIO_InitStruct.Pin = ADCx_CHANNELa_PIN;
GPIO_InitStruct.Mode = GPIO_MODE_ANALOG;
GPIO_InitStruct.Pull = GPIO_NOPULL;
HAL_GPIO_Init(ADCx_CHANNELa_GPIO_PORT, &GPIO_InitStruct);
/*##-3- Configure the DMA streams ##########################################*/
/* Configure DMA parameters */
DmaHandle.Instance = ADCx_DMA_STREAM;
DmaHandle.Init.Direction = DMA_PERIPH_TO_MEMORY;
DmaHandle.Init.PeriphInc = DMA_PINC_DISABLE;
DmaHandle.Init.MemInc = DMA_MINC_ENABLE;
DmaHandle.Init.PeriphDataAlignment = DMA_PDATAALIGN_WORD; /* Transfer from ADC by word to match with ADC resolution 10 or 12 bits */
DmaHandle.Init.MemDataAlignment = DMA_MDATAALIGN_HALFWORD; /* Transfer to memory by half-word to match with buffer variable type: half-word */
DmaHandle.Init.Mode = DMA_CIRCULAR;
DmaHandle.Init.Priority = DMA_PRIORITY_HIGH;
/* Deinitialize & Initialize the DMA for new transfer */
HAL_DMA_DeInit(&DmaHandle);
HAL_DMA_Init(&DmaHandle);
/* Associate the initialized DMA handle to the ADC handle */
__HAL_LINKDMA(hadc, DMA_Handle, DmaHandle);
/*##-4- Configure the NVIC #################################################*/
/* NVIC configuration for DMA interrupt (transfer completion or error) */
/* Priority: high-priority */
HAL_NVIC_SetPriority(ADCx_DMA_IRQn, 1, 0);
HAL_NVIC_EnableIRQ(ADCx_DMA_IRQn);
/* NVIC configuration for ADC interrupt */
/* Priority: high-priority */
HAL_NVIC_SetPriority(ADCx_IRQn, 0, 0);
HAL_NVIC_EnableIRQ(ADCx_IRQn);
}
