static void otc570_nand_hw_init(void)
{
unsigned long csa;
at91_smc_t *smc = (at91_smc_t *) ATMEL_BASE_SMC0;
at91_matrix_t *matrix = (at91_matrix_t *) ATMEL_BASE_MATRIX;
/* Enable CS3 */
csa = readl(&matrix->csa[0]) | AT91_MATRIX_CSA_EBI_CS3A;
writel(csa, &matrix->csa[0]);
/* Configure SMC CS3 for NAND/SmartMedia */
writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(1) |
AT91_SMC_SETUP_NRD(2) | AT91_SMC_SETUP_NCS_RD(2),
&smc->cs[3].setup);
writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(3) |
AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(3),
&smc->cs[3].pulse);
writel(AT91_SMC_CYCLE_NWE(6) | AT91_SMC_CYCLE_NRD(6),
&smc->cs[3].cycle);
writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
AT91_SMC_MODE_EXNW_DISABLE |
AT91_SMC_MODE_DBW_8 |
AT91_SMC_MODE_TDF_CYCLE(12),
&smc->cs[3].mode);
/* Configure RDY/BSY */
at91_set_pio_input(CONFIG_SYS_NAND_READY_PIN, 1);
/* Enable NandFlash */
at91_set_pio_output(CONFIG_SYS_NAND_ENABLE_PIN, 1);
}
static void nand_hw_init(void)
{
struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX;
unsigned long csa;
/* Enable CS3 as NAND/SmartMedia */
csa = readl(&matrix->ebicsa);
csa |= AT91_MATRIX_CS3A_SMC_SMARTMEDIA;
writel(csa, &matrix->ebicsa);
/* Configure SMC CS3 for NAND/SmartMedia */
writel(AT91_SMC_SETUP_NWE(2) | AT91_SMC_SETUP_NCS_WR(0) |
AT91_SMC_SETUP_NRD(2) | AT91_SMC_SETUP_NCS_RD(0),
&smc->cs[3].setup);
writel(AT91_SMC_PULSE_NWE(4) | AT91_SMC_PULSE_NCS_WR(4) |
AT91_SMC_PULSE_NRD(4) | AT91_SMC_PULSE_NCS_RD(4),
&smc->cs[3].pulse);
writel(AT91_SMC_CYCLE_NWE(7) | AT91_SMC_CYCLE_NRD(7),
&smc->cs[3].cycle);
writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
AT91_SMC_MODE_EXNW_DISABLE |
AT91_SMC_MODE_DBW_8 |
AT91_SMC_MODE_TDF_CYCLE(3),
&smc->cs[3].mode);
/* Configure RDY/BSY */
at91_set_gpio_input(CONFIG_SYS_NAND_READY_PIN, 1);
/* Enable NandFlash */
at91_set_gpio_output(CONFIG_SYS_NAND_ENABLE_PIN, 1);
}
void sama5d3_xplained_nand_hw_init(void)
{
struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
at91_periph_clk_enable(ATMEL_ID_SMC);
/* Configure SMC CS3 for NAND/SmartMedia */
writel(AT91_SMC_SETUP_NWE(2) | AT91_SMC_SETUP_NCS_WR(1) |
AT91_SMC_SETUP_NRD(2) | AT91_SMC_SETUP_NCS_RD(1),
&smc->cs[3].setup);
writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(5) |
AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(5),
&smc->cs[3].pulse);
writel(AT91_SMC_CYCLE_NWE(8) | AT91_SMC_CYCLE_NRD(8),
&smc->cs[3].cycle);
writel(AT91_SMC_TIMINGS_TCLR(3) | AT91_SMC_TIMINGS_TADL(10) |
AT91_SMC_TIMINGS_TAR(3) | AT91_SMC_TIMINGS_TRR(4) |
AT91_SMC_TIMINGS_TWB(5) | AT91_SMC_TIMINGS_RBNSEL(3)|
AT91_SMC_TIMINGS_NFSEL(1), &smc->cs[3].timings);
writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
AT91_SMC_MODE_EXNW_DISABLE |
#ifdef CONFIG_SYS_NAND_DBW_16
AT91_SMC_MODE_DBW_16 |
#else /* CONFIG_SYS_NAND_DBW_8 */
AT91_SMC_MODE_DBW_8 |
#endif
AT91_SMC_MODE_TDF_CYCLE(3),
&smc->cs[3].mode);
}
static void at91sam9x5ek_nand_hw_init(void)
{
struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX;
struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
unsigned long csa;
/* Enable CS3 */
csa = readl(&matrix->ebicsa);
csa |= AT91_MATRIX_EBI_CS3A_SMC_SMARTMEDIA;
/* NAND flash on D16 */
csa |= AT91_MATRIX_NFD0_ON_D16;
/* Configure IO drive */
csa &= ~AT91_MATRIX_EBI_EBI_IOSR_NORMAL;
writel(csa, &matrix->ebicsa);
/* Configure SMC CS3 for NAND/SmartMedia */
writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(0) |
AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(0),
&smc->cs[3].setup);
writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(5) |
AT91_SMC_PULSE_NRD(4) | AT91_SMC_PULSE_NCS_RD(6),
&smc->cs[3].pulse);
writel(AT91_SMC_CYCLE_NWE(5) | AT91_SMC_CYCLE_NRD(6),
&smc->cs[3].cycle);
writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
AT91_SMC_MODE_EXNW_DISABLE |
#ifdef CONFIG_SYS_NAND_DBW_16
AT91_SMC_MODE_DBW_16 |
#else /* CONFIG_SYS_NAND_DBW_8 */
AT91_SMC_MODE_DBW_8 |
#endif
AT91_SMC_MODE_TDF_CYCLE(1),
&smc->cs[3].mode);
writel(1 << ATMEL_ID_PIOCD, &pmc->pcer);
/* Configure RDY/BSY */
at91_set_gpio_input(CONFIG_SYS_NAND_READY_PIN, 1);
/* Enable NandFlash */
at91_set_gpio_output(CONFIG_SYS_NAND_ENABLE_PIN, 1);
at91_set_a_periph(AT91_PIO_PORTD, 0, 1); /* NAND OE */
at91_set_a_periph(AT91_PIO_PORTD, 1, 1); /* NAND WE */
at91_set_a_periph(AT91_PIO_PORTD, 2, 1); /* NAND ALE */
at91_set_a_periph(AT91_PIO_PORTD, 3, 1); /* NAND CLE */
at91_set_a_periph(AT91_PIO_PORTD, 6, 1);
at91_set_a_periph(AT91_PIO_PORTD, 7, 1);
at91_set_a_periph(AT91_PIO_PORTD, 8, 1);
at91_set_a_periph(AT91_PIO_PORTD, 9, 1);
at91_set_a_periph(AT91_PIO_PORTD, 10, 1);
at91_set_a_periph(AT91_PIO_PORTD, 11, 1);
at91_set_a_periph(AT91_PIO_PORTD, 12, 1);
at91_set_a_periph(AT91_PIO_PORTD, 13, 1);
}
static void sama5d3xek_nor_hw_init(void)
{
struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
at91_periph_clk_enable(ATMEL_ID_SMC);
/* Configure SMC CS0 for NOR flash */
writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(0) |
AT91_SMC_SETUP_NRD(2) | AT91_SMC_SETUP_NCS_RD(0),
&smc->cs[0].setup);
writel(AT91_SMC_PULSE_NWE(10) | AT91_SMC_PULSE_NCS_WR(11) |
AT91_SMC_PULSE_NRD(10) | AT91_SMC_PULSE_NCS_RD(11),
&smc->cs[0].pulse);
writel(AT91_SMC_CYCLE_NWE(11) | AT91_SMC_CYCLE_NRD(14),
&smc->cs[0].cycle);
writel(AT91_SMC_TIMINGS_TCLR(0) | AT91_SMC_TIMINGS_TADL(0) |
AT91_SMC_TIMINGS_TAR(0) | AT91_SMC_TIMINGS_TRR(0) |
AT91_SMC_TIMINGS_TWB(0) | AT91_SMC_TIMINGS_RBNSEL(0)|
AT91_SMC_TIMINGS_NFSEL(0), &smc->cs[0].timings);
writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
AT91_SMC_MODE_EXNW_DISABLE |
AT91_SMC_MODE_DBW_16 |
AT91_SMC_MODE_TDF_CYCLE(1),
&smc->cs[0].mode);
/* Address pin (A1 ~ A23) configuration */
at91_set_a_periph(AT91_PIO_PORTE, 1, 0);
at91_set_a_periph(AT91_PIO_PORTE, 2, 0);
at91_set_a_periph(AT91_PIO_PORTE, 3, 0);
at91_set_a_periph(AT91_PIO_PORTE, 4, 0);
at91_set_a_periph(AT91_PIO_PORTE, 5, 0);
at91_set_a_periph(AT91_PIO_PORTE, 6, 0);
at91_set_a_periph(AT91_PIO_PORTE, 7, 0);
at91_set_a_periph(AT91_PIO_PORTE, 8, 0);
at91_set_a_periph(AT91_PIO_PORTE, 9, 0);
at91_set_a_periph(AT91_PIO_PORTE, 10, 0);
at91_set_a_periph(AT91_PIO_PORTE, 11, 0);
at91_set_a_periph(AT91_PIO_PORTE, 12, 0);
at91_set_a_periph(AT91_PIO_PORTE, 13, 0);
at91_set_a_periph(AT91_PIO_PORTE, 14, 0);
at91_set_a_periph(AT91_PIO_PORTE, 15, 0);
at91_set_a_periph(AT91_PIO_PORTE, 16, 0);
at91_set_a_periph(AT91_PIO_PORTE, 17, 0);
at91_set_a_periph(AT91_PIO_PORTE, 18, 0);
at91_set_a_periph(AT91_PIO_PORTE, 19, 0);
at91_set_a_periph(AT91_PIO_PORTE, 20, 0);
at91_set_a_periph(AT91_PIO_PORTE, 21, 0);
at91_set_a_periph(AT91_PIO_PORTE, 22, 0);
at91_set_a_periph(AT91_PIO_PORTE, 23, 0);
/* CS0 pin configuration */
at91_set_a_periph(AT91_PIO_PORTE, 26, 0);
}
static void at91sam9n12ek_nand_hw_init(void)
{
struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX;
unsigned long csa;
/* Assign CS3 to NAND/SmartMedia Interface */
csa = readl(&matrix->ebicsa);
csa |= AT91_MATRIX_EBI_CS3A_SMC_SMARTMEDIA;
/* Configure databus */
csa &= ~AT91_MATRIX_NFD0_ON_D16; /* nandflash connect to D0~D15 */
/* Configure IO drive */
csa |= AT91_MATRIX_EBI_EBI_IOSR_NORMAL;
writel(csa, &matrix->ebicsa);
/* Configure SMC CS3 for NAND/SmartMedia */
writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(0) |
AT91_SMC_SETUP_NRD(2) | AT91_SMC_SETUP_NCS_RD(0),
&smc->cs[3].setup);
writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(5) |
AT91_SMC_PULSE_NRD(4) | AT91_SMC_PULSE_NCS_RD(6),
&smc->cs[3].pulse);
writel(AT91_SMC_CYCLE_NWE(5) | AT91_SMC_CYCLE_NRD(7),
&smc->cs[3].cycle);
writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
AT91_SMC_MODE_EXNW_DISABLE |
#ifdef CONFIG_SYS_NAND_DBW_16
AT91_SMC_MODE_DBW_16 |
#else /* CONFIG_SYS_NAND_DBW_8 */
AT91_SMC_MODE_DBW_8 |
#endif
AT91_SMC_MODE_TDF_CYCLE(1),
&smc->cs[3].mode);
/* Configure RDY/BSY pin */
at91_set_pio_input(AT91_PIO_PORTD, 5, 1);
/* Configure ENABLE pin for NandFlash */
at91_set_pio_output(AT91_PIO_PORTD, 4, 1);
at91_set_a_periph(AT91_PIO_PORTD, 0, 1); /* NAND OE */
at91_set_a_periph(AT91_PIO_PORTD, 1, 1); /* NAND WE */
at91_set_a_periph(AT91_PIO_PORTD, 2, 1); /* ALE */
at91_set_a_periph(AT91_PIO_PORTD, 3, 1); /* CLE */
}
static int gurnard_nand_hw_init(void)
{
struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX;
struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
ulong flags;
int ret;
/* Enable CS3 as NAND/SmartMedia */
setbits_le32(&matrix->ebicsa, AT91_MATRIX_EBI_CS3A_SMC_SMARTMEDIA);
/* Configure SMC CS3 for NAND/SmartMedia */
writel(AT91_SMC_SETUP_NWE(2) | AT91_SMC_SETUP_NCS_WR(0) |
AT91_SMC_SETUP_NRD(2) | AT91_SMC_SETUP_NCS_RD(0),
&smc->cs[3].setup);
writel(AT91_SMC_PULSE_NWE(4) | AT91_SMC_PULSE_NCS_WR(4) |
AT91_SMC_PULSE_NRD(4) | AT91_SMC_PULSE_NCS_RD(4),
&smc->cs[3].pulse);
writel(AT91_SMC_CYCLE_NWE(7) | AT91_SMC_CYCLE_NRD(7),
&smc->cs[3].cycle);
#ifdef CONFIG_SYS_NAND_DBW_16
flags = AT91_SMC_MODE_DBW_16;
#else
flags = AT91_SMC_MODE_DBW_8;
#endif
writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
AT91_SMC_MODE_EXNW_DISABLE |
flags |
AT91_SMC_MODE_TDF_CYCLE(3),
&smc->cs[3].mode);
ret = gpio_request(CONFIG_SYS_NAND_READY_PIN, "nand_rdy");
if (ret)
return ret;
gpio_direction_input(CONFIG_SYS_NAND_READY_PIN);
/* Enable NandFlash */
ret = gpio_request(CONFIG_SYS_NAND_ENABLE_PIN, "nand_ce");
if (ret)
return ret;
gpio_direction_output(CONFIG_SYS_NAND_ENABLE_PIN, 1);
return 0;
}
/*
* Miscelaneous platform dependent initialisations
*/
static void wb45n_nand_hw_init(void)
{
struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX;
unsigned long csa;
csa = readl(&matrix->ebicsa);
/* Enable CS3 */
csa |= AT91_MATRIX_EBI_CS3A_SMC_SMARTMEDIA;
/* NAND flash on D0 */
csa &= ~AT91_MATRIX_NFD0_ON_D16;
writel(csa, &matrix->ebicsa);
/* Configure SMC CS3 for NAND/SmartMedia */
writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(0) |
AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(0),
&smc->cs[3].setup);
writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(5) |
AT91_SMC_PULSE_NRD(4) | AT91_SMC_PULSE_NCS_RD(6),
&smc->cs[3].pulse);
writel(AT91_SMC_CYCLE_NWE(5) | AT91_SMC_CYCLE_NRD(6),
&smc->cs[3].cycle);
writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
AT91_SMC_MODE_EXNW_DISABLE |
AT91_SMC_MODE_DBW_8 |
AT91_SMC_MODE_TDF_CYCLE(1), &smc->cs[3].mode);
at91_periph_clk_enable(ATMEL_ID_PIOCD);
/* Configure RDY/BSY */
at91_set_gpio_input(CONFIG_SYS_NAND_READY_PIN, 1);
/* Enable NandFlash */
at91_set_gpio_output(CONFIG_SYS_NAND_ENABLE_PIN, 1);
/* Disable Flash Write Protect Line */
at91_set_gpio_output(AT91_PIN_PD10, 1);
at91_set_a_periph(AT91_PIO_PORTD, 0, 1); /* NAND OE */
at91_set_a_periph(AT91_PIO_PORTD, 1, 1); /* NAND WE */
at91_set_a_periph(AT91_PIO_PORTD, 2, 1); /* NAND ALE */
at91_set_a_periph(AT91_PIO_PORTD, 3, 1); /* NAND CLE */
}
void at91sam9n12ek_ks8851_hw_init(void)
{
struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
writel(AT91_SMC_SETUP_NWE(2) | AT91_SMC_SETUP_NCS_WR(0) |
AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(0),
&smc->cs[2].setup);
writel(AT91_SMC_PULSE_NWE(7) | AT91_SMC_PULSE_NCS_WR(7) |
AT91_SMC_PULSE_NRD(7) | AT91_SMC_PULSE_NCS_RD(7),
&smc->cs[2].pulse);
writel(AT91_SMC_CYCLE_NWE(9) | AT91_SMC_CYCLE_NRD(9),
&smc->cs[2].cycle);
writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
AT91_SMC_MODE_EXNW_DISABLE |
AT91_SMC_MODE_BAT | AT91_SMC_MODE_DBW_16 |
AT91_SMC_MODE_TDF_CYCLE(1),
&smc->cs[2].mode);
/* Configure NCS2 PIN */
at91_set_b_periph(AT91_PIO_PORTD, 19, 0);
}
static void sama5d4_xplained_nand_hw_init(void)
{
struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
at91_periph_clk_enable(ATMEL_ID_SMC);
/* Configure SMC CS3 for NAND */
writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(1) |
AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(1),
&smc->cs[3].setup);
writel(AT91_SMC_PULSE_NWE(2) | AT91_SMC_PULSE_NCS_WR(3) |
AT91_SMC_PULSE_NRD(2) | AT91_SMC_PULSE_NCS_RD(3),
&smc->cs[3].pulse);
writel(AT91_SMC_CYCLE_NWE(5) | AT91_SMC_CYCLE_NRD(5),
&smc->cs[3].cycle);
writel(AT91_SMC_TIMINGS_TCLR(2) | AT91_SMC_TIMINGS_TADL(7) |
AT91_SMC_TIMINGS_TAR(2) | AT91_SMC_TIMINGS_TRR(3) |
AT91_SMC_TIMINGS_TWB(7) | AT91_SMC_TIMINGS_RBNSEL(3)|
AT91_SMC_TIMINGS_NFSEL(1), &smc->cs[3].timings);
writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
AT91_SMC_MODE_EXNW_DISABLE |
AT91_SMC_MODE_DBW_8 |
AT91_SMC_MODE_TDF_CYCLE(3),
&smc->cs[3].mode);
at91_set_a_periph(AT91_PIO_PORTC, 5, 0); /* D0 */
at91_set_a_periph(AT91_PIO_PORTC, 6, 0); /* D1 */
at91_set_a_periph(AT91_PIO_PORTC, 7, 0); /* D2 */
at91_set_a_periph(AT91_PIO_PORTC, 8, 0); /* D3 */
at91_set_a_periph(AT91_PIO_PORTC, 9, 0); /* D4 */
at91_set_a_periph(AT91_PIO_PORTC, 10, 0); /* D5 */
at91_set_a_periph(AT91_PIO_PORTC, 11, 0); /* D6 */
at91_set_a_periph(AT91_PIO_PORTC, 12, 0); /* D7 */
at91_set_a_periph(AT91_PIO_PORTC, 13, 0); /* RE */
at91_set_a_periph(AT91_PIO_PORTC, 14, 0); /* WE */
at91_set_a_periph(AT91_PIO_PORTC, 15, 1); /* NCS */
at91_set_a_periph(AT91_PIO_PORTC, 16, 1); /* RDY */
at91_set_a_periph(AT91_PIO_PORTC, 17, 1); /* ALE */
at91_set_a_periph(AT91_PIO_PORTC, 18, 1); /* CLE */
}
static void sbc35_a9g20_nand_hw_init(void)
{
struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX;
unsigned long csa;
/* Enable CS3 */
csa = readl(&matrix->ebicsa);
csa |= AT91_MATRIX_CS3A_SMC_SMARTMEDIA;
writel(csa, &matrix->ebicsa);
/* Configure SMC CS3 for NAND/SmartMedia */
writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(0) |
AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(0),
&smc->cs[3].setup);
writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(3) |
AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(3),
&smc->cs[3].pulse);
writel(AT91_SMC_CYCLE_NWE(5) | AT91_SMC_CYCLE_NRD(5),
&smc->cs[3].cycle);
writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
AT91_SMC_MODE_EXNW_DISABLE |
#ifdef CONFIG_SYS_NAND_DBW_16
AT91_SMC_MODE_DBW_16 |
#else /* CONFIG_SYS_NAND_DBW_8 */
AT91_SMC_MODE_DBW_8 |
#endif
AT91_SMC_MODE_TDF_CYCLE(2),
&smc->cs[3].mode);
writel(1 << ATMEL_ID_PIOC, &pmc->pcer);
/* Configure RDY/BSY */
at91_set_gpio_input(CONFIG_SYS_NAND_READY_PIN, 1);
/* Enable NandFlash */
at91_set_gpio_output(CONFIG_SYS_NAND_ENABLE_PIN, 1);
}
static void pm9g45_nand_hw_init(void)
{
unsigned long csa;
struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX;
struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
/* Enable CS3 */
csa = readl(&matrix->ccr[6]) | AT91_MATRIX_CSA_EBI_CS3A;
writel(csa, &matrix->ccr[6]);
/* Configure SMC CS3 for NAND/SmartMedia */
writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(0) |
AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(0),
&smc->cs[3].setup);
writel(AT91_SMC_PULSE_NWE(4) | AT91_SMC_PULSE_NCS_WR(3) |
AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(2),
&smc->cs[3].pulse);
writel(AT91_SMC_CYCLE_NWE(7) | AT91_SMC_CYCLE_NRD(4),
&smc->cs[3].cycle);
writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
AT91_SMC_MODE_EXNW_DISABLE |
AT91_SMC_MODE_DBW_8 |
AT91_SMC_MODE_TDF_CYCLE(3),
&smc->cs[3].mode);
writel(1 << ATMEL_ID_PIOC, &pmc->pcer);
#ifdef CONFIG_SYS_NAND_READY_PIN
/* Configure RDY/BSY */
gpio_direction_input(CONFIG_SYS_NAND_READY_PIN);
#endif
/* Enable NandFlash */
gpio_direction_output(CONFIG_SYS_NAND_ENABLE_PIN, 1);
}
/**
* Initialise the memory bus settings so that we can talk to the
* memory mapped FPGA
*/
static int fpga_hw_init(void)
{
struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX;
struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
int i;
setbits_le32(&matrix->ebicsa, AT91_MATRIX_EBI_CS1A_SDRAMC);
at91_set_a_periph(2, 4, 0); /* EBIA21 */
at91_set_a_periph(2, 5, 0); /* EBIA22 */
at91_set_a_periph(2, 6, 0); /* EBIA23 */
at91_set_a_periph(2, 7, 0); /* EBIA24 */
at91_set_a_periph(2, 12, 0); /* EBIA25 */
for (i = 15; i <= 31; i++) /* EBINWAIT & EBID16 - 31 */
at91_set_a_periph(2, i, 0);
/* configure SMC cs0 for FPGA access timing */
writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(2) |
AT91_SMC_SETUP_NRD(0) | AT91_SMC_SETUP_NCS_RD(2),
&smc->cs[0].setup);
writel(AT91_SMC_PULSE_NWE(5) | AT91_SMC_PULSE_NCS_WR(4) |
AT91_SMC_PULSE_NRD(6) | AT91_SMC_PULSE_NCS_RD(4),
&smc->cs[0].pulse);
writel(AT91_SMC_CYCLE_NWE(6) | AT91_SMC_CYCLE_NRD(6),
&smc->cs[0].cycle);
writel(AT91_SMC_MODE_BAT |
AT91_SMC_MODE_EXNW_DISABLE |
AT91_SMC_MODE_DBW_32 |
AT91_SMC_MODE_TDF |
AT91_SMC_MODE_TDF_CYCLE(2),
&smc->cs[0].mode);
/* Do a write to within EBI_CS1 to enable the SDCK */
writel(0, ATMEL_BASE_CS1);
return 0;
}
/*
* Static memory controller initialization to enable Beckhoff ET1100 EtherCAT
* controller debugging
* The ET1100 is located at physical address 0x70000000
* Its process memory is located at physical address 0x70001000
*/
static void otc570_ethercat_hw_init(void)
{
at91_smc_t *smc1 = (at91_smc_t *) ATMEL_BASE_SMC1;
/* Configure SMC EBI1_CS0 for EtherCAT */
writel(AT91_SMC_SETUP_NWE(0) | AT91_SMC_SETUP_NCS_WR(0) |
AT91_SMC_SETUP_NRD(0) | AT91_SMC_SETUP_NCS_RD(0),
&smc1->cs[0].setup);
writel(AT91_SMC_PULSE_NWE(4) | AT91_SMC_PULSE_NCS_WR(9) |
AT91_SMC_PULSE_NRD(5) | AT91_SMC_PULSE_NCS_RD(9),
&smc1->cs[0].pulse);
writel(AT91_SMC_CYCLE_NWE(10) | AT91_SMC_CYCLE_NRD(6),
&smc1->cs[0].cycle);
/*
* Configure behavior at external wait signal, byte-select mode, 16 bit
* data bus width, none data float wait states and TDF optimization
*/
writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_EXNW_READY |
AT91_SMC_MODE_DBW_16 | AT91_SMC_MODE_TDF_CYCLE(0) |
AT91_SMC_MODE_TDF, &smc1->cs[0].mode);
/* Configure RDY/BSY */
at91_set_b_periph(AT91_PIO_PORTE, 20, 0); /* EBI1_NWAIT */
}