void initClock()
{
sysctlPowerUp(SYSCTL_POWERDOWN_SYSOSC_PD); // Enable system oscillator
for (volatile int i = 0; i < 1000; i++) { }
Chip_Clock_SetSystemPLLSource(SYSCTL_PLLCLKSRC_MAINOSC);
sysctlPowerDown(SYSCTL_POWERDOWN_SYSPLL_PD);
/*
* Setup PLL for main oscillator rate (FCLKIN = 12MHz) * 4 = 48MHz
* MSEL = 3 (this is pre-decremented), PSEL = 1 (for P = 2)
* FCLKOUT = FCLKIN * (MSEL + 1) = 12MHz * 4 = 48MHz
* FCCO = FCLKOUT * 2 * P = 48MHz * 2 * 2 = 192MHz (within FCCO range)
*/
Chip_Clock_SetupSystemPLL(3, 1);
sysctlPowerUp(SYSCTL_POWERDOWN_SYSPLL_PD);
while (!Chip_Clock_IsSystemPLLLocked()) { }
Chip_Clock_SetSysClockDiv(1);
Chip_FMC_SetFLASHAccess(FLASHTIM_50MHZ_CPU);
Chip_Clock_SetMainClockSource(SYSCTL_MAINCLKSRC_PLLOUT);
SystemCoreClock = Chip_Clock_GetSystemClockRate();
while (SystemCoreClock != 48000000) { } // Loop forever if the clock failed to initialize properly
}
/* Set up and initialize hardware prior to call to main */
void Chip_SetupIrcClocking(void)
{
/* IRC should be powered up */
Chip_SYSCTL_PowerUp(SYSCTL_POWERDOWN_IRC_PD);
Chip_SYSCTL_PowerUp(SYSCTL_POWERDOWN_IRCOUT_PD);
/* Set system PLL input to main oscillator */
Chip_Clock_SetSystemPLLSource(SYSCTL_PLLCLKSRC_IRC);
/* Power down PLL to change the PLL divider ratio */
Chip_SYSCTL_PowerDown(SYSCTL_POWERDOWN_SYSPLL_PD);
/* Setup PLL for main oscillator rate (FCLKIN = 12MHz) * 6 = 72MHz
MSEL = 5 (this is pre-decremented), PSEL = 1 (for P = 2)
FCLKOUT = FCLKIN * (MSEL + 1) = 12MHz * 6 = 72MHz
FCCO = FCLKOUT * 2 * P = 72MHz * 2 * 2 = 288MHz (within FCCO range) */
Chip_Clock_SetupSystemPLL(5, 1);
/* Powerup system PLL */
Chip_SYSCTL_PowerUp(SYSCTL_POWERDOWN_SYSPLL_PD);
/* Wait for PLL to lock */
while (!Chip_Clock_IsSystemPLLLocked()) {}
/* Set system clock divider to 1 */
Chip_Clock_SetSysClockDiv(1);
/* Setup FLASH access to 3 clocks */
Chip_FMC_SetFLASHAccess(FLASHTIM_72MHZ_CPU);
/* Set main clock source to the system PLL. This will drive 48MHz
for the main clock and 48MHz for the system clock */
Chip_Clock_SetMainClockSource(SYSCTL_MAINCLKSRC_PLLOUT);
}
/* Setup system clocking */
STATIC void SystemSetupClocking(void)
{
volatile int i;
/* Powerup main oscillator */
Chip_SYSCTL_PowerUp(SYSCTL_POWERDOWN_SYSOSC_PD);
/* Wait 200us for OSC to be stablized, no status
indication, dummy wait. */
for (i = 0; i < 0x100; i++) {}
/* Set system PLL input to main oscillator */
Chip_Clock_SetSystemPLLSource(SYSCTL_PLLCLKSRC_MAINOSC);
/* Power down PLL to change the PLL divider ratio */
Chip_SYSCTL_PowerDown(SYSCTL_POWERDOWN_SYSPLL_PD);
/* Setup PLL for main oscillator rate (FCLKIN = 12MHz) * 4 = 48MHz
MSEL = 3 (this is pre-decremented), PSEL = 1 (for P = 2)
FCLKOUT = FCLKIN * (MSEL + 1) = 12MHz * 4 = 48MHz
FCCO = FCLKOUT * 2 * P = 48MHz * 2 * 2 = 192MHz (within FCCO range) */
Chip_Clock_SetupSystemPLL(3, 1);
/* Powerup system PLL */
Chip_SYSCTL_PowerUp(SYSCTL_POWERDOWN_SYSPLL_PD);
/* Wait for PLL to lock */
while (!Chip_Clock_IsSystemPLLLocked()) {}
/* Set system clock divider to 1 */
Chip_Clock_SetSysClockDiv(1);
/* Setup FLASH access to 3 clocks */
Chip_FMC_SetFLASHAccess(FLASHTIM_50MHZ_CPU);
/* Set main clock source to the system PLL. This will drive 48MHz
for the main clock and 48MHz for the system clock */
Chip_Clock_SetMainClockSource(SYSCTL_MAINCLKSRC_PLLOUT);
/* Set USB PLL input to main oscillator */
Chip_Clock_SetUSBPLLSource(SYSCTL_PLLCLKSRC_MAINOSC);
/* Setup USB PLL (FCLKIN = 12MHz) * 4 = 48MHz
MSEL = 3 (this is pre-decremented), PSEL = 1 (for P = 2)
FCLKOUT = FCLKIN * (MSEL + 1) = 12MHz * 4 = 48MHz
FCCO = FCLKOUT * 2 * P = 48MHz * 2 * 2 = 192MHz (within FCCO range) */
Chip_Clock_SetupUSBPLL(3, 1);
/* Powerup USB PLL */
Chip_SYSCTL_PowerUp(SYSCTL_POWERDOWN_USBPLL_PD);
/* Wait for PLL to lock */
while (!Chip_Clock_IsUSBPLLLocked()) {}
}
/* Clock and PLL initialization based on the external oscillator */
void Chip_SetupXtalClocking(void)
{
volatile int i;
#if defined(USE_ROM_API)
uint32_t cmd[4], resp[2];
#endif
/* Powerup main oscillator */
Chip_SYSCTL_PowerUp(SYSCTL_POWERDOWN_SYSOSC_PD);
/* Wait for at least 580uS for osc to stabilize */
for (i = 0; i < 2500; i++) {}
/* Set system PLL input to main oscillator */
Chip_Clock_SetSystemPLLSource(SYSCTL_PLLCLKSRC_MAINOSC);
/* Setup FLASH access to 2 clocks */
Chip_FMC_SetFLASHAccess(FLASHTIM_2CLK_CPU);
#if defined(USE_ROM_API)
/* Use ROM API for setting up PLL */
cmd[0] = Chip_Clock_GetMainOscRate() / 1000; /* in KHz */
cmd[1] = 48000000 / 1000; /* 48MHz system clock rate */
cmd[2] = CPU_FREQ_EQU;
cmd[3] = 48000000 / 10000; /* Timeout */
LPC_PWRD_API->set_pll(cmd, resp);
/* Dead loop on fail */
while (resp[0] != PLL_CMD_SUCCESS) {}
#else
/* Power down PLL to change the PLL divider ratio */
Chip_SYSCTL_PowerDown(SYSCTL_POWERDOWN_SYSPLL_PD);
/* Setup PLL for main oscillator rate (FCLKIN = 12MHz) * 4 = 48MHz
MSEL = 3 (this is pre-decremented), PSEL = 1 (for P = 2)
FCLKOUT = FCLKIN * (MSEL + 1) = 12MHz * 4 = 48MHz
FCCO = FCLKOUT * 2 * P = 48MHz * 2 * 2 = 192MHz (within FCCO range) */
Chip_Clock_SetupSystemPLL(3, 1);
/* Powerup system PLL */
Chip_SYSCTL_PowerUp(SYSCTL_POWERDOWN_SYSPLL_PD);
/* Wait for PLL to lock */
while (!Chip_Clock_IsSystemPLLLocked()) {}
/* Set system clock divider to 1 */
Chip_Clock_SetSysClockDiv(1);
/* Set main clock source to the system PLL. This will drive 48MHz
for the main clock and 48MHz for the system clock */
Chip_Clock_SetMainClockSource(SYSCTL_MAINCLKSRC_PLLOUT);
#endif
}
/* Setup system clocking */
STATIC void Board_SetupXtalClocking(void)
{
#if USE_CLKIN_IN
uint32_t i;
#endif
/* A library"pmu_library.lib) has been created to facilitate the power management
operation. The user needs to enter the desired frequency the application wants to
run, the set_voltage() will set the internal voltage regulators automatically. */
set_voltage( SYSCTL_IRC_FREQ * PLL_MULTIPLIER );
/* Select the PLL input in the IRC */
#if USE_CLKIN_IN
/* IOCON clock left on, this is needed is CLKIN is used. */
Chip_Clock_EnablePeriphClock(SYSCTL_CLOCK_IOCON);
Chip_IOCON_PinMuxSet(LPC_IOCON, 0, 22, IOCON_MODE_PULLUP | IOCON_FUNC1 | IOCON_DIGITAL_EN | IOCON_INPFILT_OFF);
/* Delay to wait until CLKIN stablized */
for ( i = 0; i < 500; i++ ) {}
Chip_Clock_SetSystemPLLSource(SYSCTL_PLLCLKSRC_CLKIN);
/* Wait State setting TBD */
/* Setup FLASH access to 2 clocks (up to 20MHz) */
Chip_FMC_SetFLASHAccess(FLASHTIM_72MHZ_CPU);
#else
Chip_Clock_SetSystemPLLSource(SYSCTL_PLLCLKSRC_IRC);
/* Wait State setting TBD */
/* Setup FLASH access to 5 clocks (up to 72MHz) */
Chip_FMC_SetFLASHAccess(FLASHTIM_72MHZ_CPU);
#endif
/* Power down PLL to change the PLL divider ratio */
Chip_SYSCTL_PowerDown(PDRUNCFG_PD_SYS_PLL0);
/* First parameter is the multiplier, the second parameter is the input frequency in MHz */
#if USE_CLKIN_IN
Chip_Clock_SetupSystemPLL(PLL_MULTIPLIER, ExtRateIn);
#else
Chip_Clock_SetupSystemPLL(PLL_MULTIPLIER, SYSCTL_IRC_FREQ);
#endif
/* Turn on the PLL by clearing the power down bit */
Chip_SYSCTL_PowerUp(PDRUNCFG_PD_SYS_PLL0);
/* Wait for PLL to lock */
while (!Chip_Clock_IsSystemPLLLocked()) {}
/* Set system clock divider to 1 */
Chip_Clock_SetSysClockDiv(1);
/* Set main clock source to the system PLL. This will drive 24MHz
for the main clock and 24MHz for the system clock */
Chip_Clock_SetMainClockSource(SYSCTL_MAINCLKSRC_PLLOUT);
}
/* Set up and initialize hardware prior to call to main */
void Chip_SystemInit(void)
{
#ifdef SUPPORT_NXP_MAIN_OSC
volatile uint32_t i;
Chip_SYSCTL_PowerUp(SYSCTL_POWERDOWN_SYSOSC_PD);
Chip_Clock_SetPLLBypass(0, 0);
for (i = 0; i < 200; i++) __NOP();
Chip_Clock_SetSystemPLLSource(SYSCTL_PLLCLKSRC_MAINOSC);
#else
/* IRC should be powered up */
Chip_SYSCTL_PowerUp(SYSCTL_POWERDOWN_IRC_PD);
Chip_SYSCTL_PowerUp(SYSCTL_POWERDOWN_IRCOUT_PD);
/* Set system PLL input to main oscillator */
Chip_Clock_SetSystemPLLSource(SYSCTL_PLLCLKSRC_IRC);
#endif
/* Power down PLL to change the PLL divider ratio */
Chip_SYSCTL_PowerDown(SYSCTL_POWERDOWN_SYSPLL_PD);
#ifdef SUPPORT_NXP_MAIN_OSC
Chip_Clock_SetupSystemPLL(3, 2);
#else
/* Setup PLL for main oscillator rate (FCLKIN = 12MHz) * 4 = 48MHz
MSEL = 3 (this is pre-decremented), PSEL = 1 (for P = 2)
FCLKOUT = FCLKIN * (MSEL + 1) = 12MHz * 4 = 48MHz
FCCO = FCLKOUT * 2 * P = 48MHz * 2 * 2 = 192MHz (within FCCO range) */
Chip_Clock_SetupSystemPLL(3, 1);
#endif
/* Powerup system PLL */
Chip_SYSCTL_PowerUp(SYSCTL_POWERDOWN_SYSPLL_PD);
/* Wait for PLL to lock */
while (!Chip_Clock_IsSystemPLLLocked()) {}
/* Set system clock divider to 1 */
Chip_Clock_SetSysClockDiv(1);
/* Setup FLASH access to 3 clocks */
Chip_FMC_SetFLASHAccess(FLASHTIM_50MHZ_CPU);
/* Set main clock source to the system PLL. This will drive 48MHz
for the main clock and 48MHz for the system clock */
Chip_Clock_SetMainClockSource(SYSCTL_MAINCLKSRC_PLLOUT);
/* Enable IOCON clock */
Chip_Clock_EnablePeriphClock(SYSCTL_CLOCK_IOCON);
}
/* Clock and PLL initialization based on the internal oscillator */
void Chip_SetupIrcClocking(void)
{
#if defined(USE_ROM_API)
uint32_t cmd[4], resp[2];
#endif
/* Turn on the IRC by clearing the power down bit */
Chip_SYSCTL_PowerUp(SYSCTL_POWERDOWN_IRC_PD);
/* Select the PLL input in the IRC */
Chip_Clock_SetSystemPLLSource(SYSCTL_PLLCLKSRC_IRC);
/* Setup FLASH access */
Chip_FMC_SetFLASHAccess(FLASHTIM_2CLK_CPU);
#if defined(USE_ROM_API)
/* Use ROM API for setting up PLL */
cmd[0] = Chip_Clock_GetIntOscRate() / 1000; /* in KHz */
cmd[1] = 48000000 / 1000; /* 48MHz system clock rate */
cmd[2] = CPU_FREQ_EQU;
cmd[3] = 48000000 / 10000; /* Timeout */
LPC_PWRD_API->set_pll(cmd, resp);
/* Dead loop on fail */
while (resp[0] != PLL_CMD_SUCCESS) {}
#else
/* Power down PLL to change the PLL divider ratio */
Chip_SYSCTL_PowerDown(SYSCTL_POWERDOWN_SYSPLL_PD);
/* Configure the PLL M and P dividers */
/* Setup PLL for main oscillator rate (FCLKIN = 12MHz) * 4 = 48MHz
MSEL = 3 (this is pre-decremented), PSEL = 1 (for P = 2)
FCLKOUT = FCLKIN * (MSEL + 1) = 12MHz * 4 = 48MHz
FCCO = FCLKOUT * 2 * P = 48MHz * 2 * 2 = 192MHz (within FCCO range) */
Chip_Clock_SetupSystemPLL(3, 1);
/* Turn on the PLL by clearing the power down bit */
Chip_SYSCTL_PowerUp(SYSCTL_POWERDOWN_SYSPLL_PD);
/* Wait for PLL to lock */
while (!Chip_Clock_IsSystemPLLLocked()) {}
/* Set system clock divider to 1 */
Chip_Clock_SetSysClockDiv(1);
/* Set main clock source to the system PLL. This will drive 24MHz
for the main clock and 24MHz for the system clock */
Chip_Clock_SetMainClockSource(SYSCTL_MAINCLKSRC_PLLOUT);
#endif
}
/**
* @brief Main program body
* @return Does not return
*/
int main(void)
{
/* Generic Initialization */
SystemCoreClockUpdate();
/* Board_Init calls Chip_GPIO_Init and enables GPIO clock if needed,
Chip_GPIO_Init is not called again */
Board_Init();
Board_LED_Set(0, false);
Chip_PININT_Init(LPC_PININT);
/* Configure GPIO pin as input */
Chip_GPIO_SetPinDIRInput(LPC_GPIO, GPIO_PININT_PORT, GPIO_PININT_PIN);
/* Configure pin as GPIO */
Chip_IOCON_PinMuxSet(LPC_IOCON, GPIO_PININT_PORT, GPIO_PININT_PIN,
(IOCON_FUNC0 | IOCON_DIGITAL_EN | IOCON_GPIO_MODE));
/* Configure pin interrupt selection for the GPIO pin in Input Mux Block */
Chip_INMUX_PinIntSel(GPIO_PININT_INDEX, GPIO_PININT_PORT, GPIO_PININT_PIN);
/* Configure channel interrupt as edge sensitive and falling edge interrupt */
Chip_PININT_ClearIntStatus(LPC_PININT, PININTCH(GPIO_PININT_INDEX));
Chip_PININT_SetPinModeEdge(LPC_PININT, PININTCH(GPIO_PININT_INDEX));
Chip_PININT_EnableIntLow(LPC_PININT, PININTCH(GPIO_PININT_INDEX));
/* Enable interrupt in the NVIC */
NVIC_EnableIRQ(PININT_NVIC_NAME);
/* Enable wakeup for PININT0 */
Chip_SYSCON_EnableWakeup(SYSCON_STARTER_PINT0);
/* save the clock source, power down the PLL */
saved_clksrc = Chip_Clock_GetMainClockSource();
/* Go to sleep mode - LED will toggle on each wakeup event */
while (1) {
/* Go to sleep state - will wake up automatically on interrupt */
/* Disable PLL, if previously enabled, prior to sleep */
if (saved_clksrc == SYSCON_MAINCLKSRC_PLLOUT) {
Chip_Clock_SetMainClockSource(SYSCON_MAINCLKSRC_IRC);
Chip_SYSCON_PowerDown(SYSCON_PDRUNCFG_PD_SYS_PLL);
}
/* Lower system voltages to current lock (likely IRC) */
Chip_POWER_SetVoltage(POWER_LOW_POWER_MODE, Chip_Clock_GetMainClockRate());
/* Go to sleep leaving SRAM powered during sleep. Use lower
voltage during sleep. */
Chip_POWER_EnterPowerMode(PDOWNMODE,
(SYSCON_PDRUNCFG_PD_SRAM0A | SYSCON_PDRUNCFG_PD_SRAM0B));
/* On wakeup, restore PLL power if needed */
if (saved_clksrc == SYSCON_MAINCLKSRC_PLLOUT) {
Chip_SYSCON_PowerUp(SYSCON_PDRUNCFG_PD_SYS_PLL);
/* Wait for PLL lock */
while (!Chip_Clock_IsSystemPLLLocked()) {}
Chip_POWER_SetVoltage(POWER_LOW_POWER_MODE, Chip_Clock_GetSystemPLLOutClockRate(false));
/* Use PLL for system clock */
Chip_Clock_SetMainClockSource(SYSCON_MAINCLKSRC_PLLOUT);
}
}
return 0;
}