void setDefault_command()
{
command::add_homing[0] = command::add_homing[1] = command::add_homing[2] = 0;
command::zprobe_zoffset = 0;
EEPROM_WRITE_VAR(eeprom_offsets::ADD_HOMING, command::add_homing);
EEPROM_WRITE_VAR(eeprom_offsets::ZPROBE_ZOFFSET,command::zprobe_zoffset);
}
void Config_StoreSettings()
{
char ver[4]= "000";
int i=EEPROM_OFFSET;
EEPROM_WRITE_VAR(i,ver); // invalidate data first
//EEPROM_WRITE_VAR(i,max_acceleration_units_per_sq_second);
//EEPROM_WRITE_VAR(i,acceleration);
char ver2[4]=EEPROM_VERSION;
i=EEPROM_OFFSET;
EEPROM_WRITE_VAR(i,ver2); // validate data
SERIAL_PGMLN("Settings Stored");
}
static void setDefaultPID(void)
{
float p = DEFAULT_P;
uint16_t location = eeprom_offsets::HEATER_PID;
EEPROM_WRITE_VAR(location, p);
float i = DEFAULT_I;
location += sizeof(float);
EEPROM_WRITE_VAR(location, i);
float d = DEFAULT_D;
location += sizeof(float);
EEPROM_WRITE_VAR(location, d);
}
void resetUserEEPROM()
{
char ver[4] = "000";
EEPROM_WRITE_VAR(eeprom_offsets::EEPROM_VERSION, ver); // invalidate data first
setDefault_plan();
setDefault_command();
setDefaultPID();
char ver2[4] = APP_EEPROM_VERSION;
EEPROM_WRITE_VAR(eeprom_offsets::EEPROM_VERSION, ver2);
}
void Config_StoreSettings() {
float dummy = 0.0f;
char ver[4] = "000";
int i = EEPROM_OFFSET;
EEPROM_WRITE_VAR(i, ver); // invalidate data first
EEPROM_WRITE_VAR(i, axis_steps_per_unit);
EEPROM_WRITE_VAR(i, max_feedrate);
EEPROM_WRITE_VAR(i, max_acceleration_units_per_sq_second);
EEPROM_WRITE_VAR(i, acceleration);
EEPROM_WRITE_VAR(i, retract_acceleration);
EEPROM_WRITE_VAR(i, travel_acceleration);
EEPROM_WRITE_VAR(i, minimumfeedrate);
EEPROM_WRITE_VAR(i, mintravelfeedrate);
EEPROM_WRITE_VAR(i, minsegmenttime);
EEPROM_WRITE_VAR(i, max_xy_jerk);
EEPROM_WRITE_VAR(i, max_z_jerk);
EEPROM_WRITE_VAR(i, max_e_jerk);
EEPROM_WRITE_VAR(i, home_offset);
uint8_t mesh_num_x = 3;
uint8_t mesh_num_y = 3;
#if ENABLED(MESH_BED_LEVELING)
// Compile time test that sizeof(mbl.z_values) is as expected
typedef char c_assert[(sizeof(mbl.z_values) == MESH_NUM_X_POINTS * MESH_NUM_Y_POINTS * sizeof(dummy)) ? 1 : -1];
mesh_num_x = MESH_NUM_X_POINTS;
mesh_num_y = MESH_NUM_Y_POINTS;
EEPROM_WRITE_VAR(i, mbl.active);
EEPROM_WRITE_VAR(i, mesh_num_x);
EEPROM_WRITE_VAR(i, mesh_num_y);
EEPROM_WRITE_VAR(i, mbl.z_values);
#else
uint8_t dummy_uint8 = 0;
EEPROM_WRITE_VAR(i, dummy_uint8);
EEPROM_WRITE_VAR(i, mesh_num_x);
EEPROM_WRITE_VAR(i, mesh_num_y);
dummy = 0.0f;
for (uint8_t q = 0; q < mesh_num_x * mesh_num_y; q++) EEPROM_WRITE_VAR(i, dummy);
#endif // MESH_BED_LEVELING
#if DISABLED(AUTO_BED_LEVELING_FEATURE)
float zprobe_zoffset = 0;
#endif
EEPROM_WRITE_VAR(i, zprobe_zoffset);
#if ENABLED(DELTA)
EEPROM_WRITE_VAR(i, endstop_adj); // 3 floats
EEPROM_WRITE_VAR(i, delta_radius); // 1 float
EEPROM_WRITE_VAR(i, delta_diagonal_rod); // 1 float
EEPROM_WRITE_VAR(i, delta_segments_per_second); // 1 float
#elif ENABLED(Z_DUAL_ENDSTOPS)
EEPROM_WRITE_VAR(i, z_endstop_adj); // 1 floats
dummy = 0.0f;
for (int q = 5; q--;) EEPROM_WRITE_VAR(i, dummy);
#else
dummy = 0.0f;
for (int q = 6; q--;) EEPROM_WRITE_VAR(i, dummy);
#endif
#if DISABLED(ULTIPANEL)
int plaPreheatHotendTemp = PLA_PREHEAT_HOTEND_TEMP, plaPreheatHPBTemp = PLA_PREHEAT_HPB_TEMP, plaPreheatFanSpeed = PLA_PREHEAT_FAN_SPEED,
absPreheatHotendTemp = ABS_PREHEAT_HOTEND_TEMP, absPreheatHPBTemp = ABS_PREHEAT_HPB_TEMP, absPreheatFanSpeed = ABS_PREHEAT_FAN_SPEED;
#endif // !ULTIPANEL
EEPROM_WRITE_VAR(i, plaPreheatHotendTemp);
EEPROM_WRITE_VAR(i, plaPreheatHPBTemp);
EEPROM_WRITE_VAR(i, plaPreheatFanSpeed);
EEPROM_WRITE_VAR(i, absPreheatHotendTemp);
EEPROM_WRITE_VAR(i, absPreheatHPBTemp);
EEPROM_WRITE_VAR(i, absPreheatFanSpeed);
for (int e = 0; e < 4; e++) {
#if ENABLED(PIDTEMP)
if (e < EXTRUDERS) {
EEPROM_WRITE_VAR(i, PID_PARAM(Kp, e));
EEPROM_WRITE_VAR(i, PID_PARAM(Ki, e));
EEPROM_WRITE_VAR(i, PID_PARAM(Kd, e));
#if ENABLED(PID_ADD_EXTRUSION_RATE)
EEPROM_WRITE_VAR(i, PID_PARAM(Kc, e));
#else
dummy = 1.0f; // 1.0 = default kc
EEPROM_WRITE_VAR(i, dummy);
#endif
}
else
#endif // !PIDTEMP
{
dummy = DUMMY_PID_VALUE; // When read, will not change the existing value
EEPROM_WRITE_VAR(i, dummy);
dummy = 0.0f;
for (int q = 3; q--;) EEPROM_WRITE_VAR(i, dummy);
}
} // Extruders Loop
#if DISABLED(PID_ADD_EXTRUSION_RATE)
int lpq_len = 20;
#endif
EEPROM_WRITE_VAR(i, lpq_len);
#if DISABLED(PIDTEMPBED)
float bedKp = DUMMY_PID_VALUE, bedKi = DUMMY_PID_VALUE, bedKd = DUMMY_PID_VALUE;
#endif
EEPROM_WRITE_VAR(i, bedKp);
EEPROM_WRITE_VAR(i, bedKi);
EEPROM_WRITE_VAR(i, bedKd);
#if DISABLED(HAS_LCD_CONTRAST)
const int lcd_contrast = 32;
#endif
EEPROM_WRITE_VAR(i, lcd_contrast);
#if ENABLED(SCARA)
EEPROM_WRITE_VAR(i, axis_scaling); // 3 floats
#else
dummy = 1.0f;
EEPROM_WRITE_VAR(i, dummy);
#endif
#if ENABLED(FWRETRACT)
EEPROM_WRITE_VAR(i, autoretract_enabled);
EEPROM_WRITE_VAR(i, retract_length);
#if EXTRUDERS > 1
EEPROM_WRITE_VAR(i, retract_length_swap);
#else
dummy = 0.0f;
EEPROM_WRITE_VAR(i, dummy);
#endif
EEPROM_WRITE_VAR(i, retract_feedrate);
EEPROM_WRITE_VAR(i, retract_zlift);
EEPROM_WRITE_VAR(i, retract_recover_length);
#if EXTRUDERS > 1
EEPROM_WRITE_VAR(i, retract_recover_length_swap);
#else
dummy = 0.0f;
EEPROM_WRITE_VAR(i, dummy);
#endif
EEPROM_WRITE_VAR(i, retract_recover_feedrate);
#endif // FWRETRACT
EEPROM_WRITE_VAR(i, volumetric_enabled);
// Save filament sizes
for (int q = 0; q < 4; q++) {
if (q < EXTRUDERS) dummy = filament_size[q];
EEPROM_WRITE_VAR(i, dummy);
}
char ver2[4] = EEPROM_VERSION;
int j = EEPROM_OFFSET;
EEPROM_WRITE_VAR(j, ver2); // validate data
// Report storage size
SERIAL_ECHO_START;
SERIAL_ECHOPAIR("Settings Stored (", (unsigned long)i);
SERIAL_ECHOLNPGM(" bytes)");
}
void Config_StoreSettings()
{
char ver[4]= "000";
int i=EEPROM_OFFSET;
EEPROM_WRITE_VAR(i,ver); // invalidate data first
EEPROM_WRITE_VAR(i,axis_steps_per_unit);
EEPROM_WRITE_VAR(i,max_feedrate);
EEPROM_WRITE_VAR(i,max_acceleration_units_per_sq_second);
EEPROM_WRITE_VAR(i,acceleration);
EEPROM_WRITE_VAR(i,retract_acceleration);
EEPROM_WRITE_VAR(i,minimumfeedrate);
EEPROM_WRITE_VAR(i,mintravelfeedrate);
EEPROM_WRITE_VAR(i,minsegmenttime);
EEPROM_WRITE_VAR(i,max_xy_jerk);
EEPROM_WRITE_VAR(i,max_z_jerk);
EEPROM_WRITE_VAR(i,max_e_jerk);
EEPROM_WRITE_VAR(i,add_homeing);
#ifdef DELTA
EEPROM_WRITE_VAR(i,endstop_adj);
EEPROM_WRITE_VAR(i,delta_radius);
EEPROM_WRITE_VAR(i,delta_diagonal_rod);
EEPROM_WRITE_VAR(i,max_pos);
EEPROM_WRITE_VAR(i,tower_adj);
EEPROM_WRITE_VAR(i,z_probe_offset);
EEPROM_WRITE_VAR(i,delta_segments_per_second);
#endif
#ifndef ULTIPANEL
int plaPreheatHotendTemp = PLA_PREHEAT_HOTEND_TEMP, plaPreheatHPBTemp = PLA_PREHEAT_HPB_TEMP, plaPreheatFanSpeed = PLA_PREHEAT_FAN_SPEED;
int absPreheatHotendTemp = ABS_PREHEAT_HOTEND_TEMP, absPreheatHPBTemp = ABS_PREHEAT_HPB_TEMP, absPreheatFanSpeed = ABS_PREHEAT_FAN_SPEED;
#endif
EEPROM_WRITE_VAR(i,plaPreheatHotendTemp);
EEPROM_WRITE_VAR(i,plaPreheatHPBTemp);
EEPROM_WRITE_VAR(i,plaPreheatFanSpeed);
EEPROM_WRITE_VAR(i,absPreheatHotendTemp);
EEPROM_WRITE_VAR(i,absPreheatHPBTemp);
EEPROM_WRITE_VAR(i,absPreheatFanSpeed);
EEPROM_WRITE_VAR(i,zprobe_zoffset);
#ifdef PIDTEMP
EEPROM_WRITE_VAR(i,Kp);
EEPROM_WRITE_VAR(i,Ki);
EEPROM_WRITE_VAR(i,Kd);
#else
float dummy = 3000.0f;
EEPROM_WRITE_VAR(i,dummy);
dummy = 0.0f;
EEPROM_WRITE_VAR(i,dummy);
EEPROM_WRITE_VAR(i,dummy);
#endif
#ifndef DOGLCD
int lcd_contrast = 32;
#endif
EEPROM_WRITE_VAR(i,lcd_contrast);
char ver2[4]=EEPROM_VERSION;
i=EEPROM_OFFSET;
EEPROM_WRITE_VAR(i,ver2); // validate data
SERIAL_ECHO_START;
SERIAL_ECHOLNPGM("Settings Stored");
}
void Config_StoreSettings()
{
char ver[4]= "000";
int i=EEPROM_OFFSET;
EEPROM_WRITE_VAR(i,ver); // invalidate data first
EEPROM_WRITE_VAR(i,axis_steps_per_unit);
EEPROM_WRITE_VAR(i,e1_steps_per_unit);
//EEPROM_WRITE_VAR(i,extruder_offset);
EEPROM_WRITE_VAR(i,max_feedrate);
EEPROM_WRITE_VAR(i,max_acceleration_units_per_sq_second);
EEPROM_WRITE_VAR(i,acceleration);
EEPROM_WRITE_VAR(i,retract_acceleration);
EEPROM_WRITE_VAR(i,minimumfeedrate);
EEPROM_WRITE_VAR(i,mintravelfeedrate);
EEPROM_WRITE_VAR(i,minsegmenttime);
EEPROM_WRITE_VAR(i,max_xy_jerk);
EEPROM_WRITE_VAR(i,max_z_jerk);
EEPROM_WRITE_VAR(i,max_e_jerk);
EEPROM_WRITE_VAR(i,add_homeing);
#ifdef DELTA
EEPROM_WRITE_VAR(i,endstop_adj);
#endif
#ifndef ULTIPANEL
int plaPreheatHotendTemp = PLA_PREHEAT_HOTEND_TEMP, plaPreheatHPBTemp = PLA_PREHEAT_HPB_TEMP, plaPreheatFanSpeed = PLA_PREHEAT_FAN_SPEED;
int hipsPreheatHotendTemp = HIPS_PREHEAT_HOTEND_TEMP, hipsPreheatHPBTemp = HIPS_PREHEAT_HPB_TEMP, hipsPreheatFanSpeed = HIPS_PREHEAT_FAN_SPEED;
int absPreheatHotendTemp = ABS_PREHEAT_HOTEND_TEMP, absPreheatHPBTemp = ABS_PREHEAT_HPB_TEMP, absPreheatFanSpeed = ABS_PREHEAT_FAN_SPEED;
int bridgePreheatHotendTemp = BRIDGE_PREHEAT_HOTEND_TEMP, bridgePreheatHPBTemp = BRIDGE_PREHEAT_HPB_TEMP, bridgePreheatFanSpeed = BRIDGE_PREHEAT_FAN_SPEED;
int pctpePreheatHotendTemp = PCTPE_PREHEAT_HOTEND_TEMP, pctpePreheatHPBTemp = PCTPE_PREHEAT_HPB_TEMP, pctpePreheatFanSpeed = PCTPE_PREHEAT_FAN_SPEED;
int alloy_910PreheatHotendTemp = ALLOY_910_PREHEAT_HOTEND_TEMP, alloy_910PreheatHPBTemp = ALLOY_910_PREHEAT_HPB_TEMP, alloy_910PreheatFanSpeed = ALLOY_910_PREHEAT_FAN_SPEED;
//~ int bambooPreheatHotendTemp = BAMBOO_PREHEAT_HOTEND_TEMP, bambooPreheatHPBTemp = BAMBO_PREHEAT_HPB_TEMP, bambooPreheatFanSpeed = BAMBOO_PREHEAT_FAN_SPEED;
int n_ventPreheatHotendTemp = N_VENT_PREHEAT_HOTEND_TEMP, n_ventPreheatHPBTemp = N_VENT_PREHEAT_HPB_TEMP, n_ventPreheatFanSpeed = N_VENT_PREHEAT_FAN_SPEED;
int laybrickPreheatHotendTemp = LAYBRICK_PREHEAT_HOTEND_TEMP, laybrickPreheatHPBTemp = LAYBRICK_PREHEAT_HPB_TEMP, laybrickPreheatFanSpeed = LAYBRICK_PREHEAT_FAN_SPEED;
int laywoodPreheatHotendTemp = LAYWOOD_PREHEAT_HOTEND_TEMP, laywoodPreheatHPBTemp = LAYWOOD_PREHEAT_HPB_TEMP, laywoodPreheatFanSpeed = LAYWOOD_PREHEAT_FAN_SPEED;
int polycarbonatePreheatHotendTemp = POLYCARBONATE_PREHEAT_HOTEND_TEMP, polycarbonatePreheatHPBTemp = POLYCARBONATE_PREHEAT_HPB_TEMP, polycarbonatePreheatFanSpeed = POLYCARBONATE_PREHEAT_FAN_SPEED;
int tglasePreheatHotendTemp = TGLASE_PREHEAT_HOTEND_TEMP, tglasePreheatHPBTemp = TGLASE_PREHEAT_HPB_TEMP, tglasePreheatFanSpeed = TGLASE_PREHEAT_FAN_SPEED;
#endif
EEPROM_WRITE_VAR(i,plaPreheatHotendTemp);
EEPROM_WRITE_VAR(i,plaPreheatHPBTemp);
EEPROM_WRITE_VAR(i,plaPreheatFanSpeed);
EEPROM_WRITE_VAR(i,hipsPreheatHotendTemp);
EEPROM_WRITE_VAR(i,hipsPreheatHPBTemp);
EEPROM_WRITE_VAR(i,hipsPreheatFanSpeed);
EEPROM_WRITE_VAR(i,absPreheatHotendTemp);
EEPROM_WRITE_VAR(i,absPreheatHPBTemp);
EEPROM_WRITE_VAR(i,absPreheatFanSpeed);
EEPROM_WRITE_VAR(i,bridgePreheatHotendTemp);
EEPROM_WRITE_VAR(i,bridgePreheatHPBTemp);
EEPROM_WRITE_VAR(i,bridgePreheatFanSpeed);
EEPROM_WRITE_VAR(i,pctpePreheatHotendTemp);
EEPROM_WRITE_VAR(i,pctpePreheatHPBTemp);
EEPROM_WRITE_VAR(i,pctpePreheatFanSpeed);
EEPROM_WRITE_VAR(i,alloy_910PreheatHotendTemp);
EEPROM_WRITE_VAR(i,alloy_910PreheatHPBTemp);
EEPROM_WRITE_VAR(i,alloy_910PreheatFanSpeed);
//~ EEPROM_WRITE_VAR(i,bambooPreheatHotendTemp);
//~ EEPROM_WRITE_VAR(i,bambooPreheatHPBTemp);
//~ EEPROM_WRITE_VAR(i,bambooPreheatFanSpeed);
EEPROM_WRITE_VAR(i,n_ventPreheatHotendTemp);
EEPROM_WRITE_VAR(i,n_ventPreheatHPBTemp);
EEPROM_WRITE_VAR(i,n_ventPreheatFanSpeed);
EEPROM_WRITE_VAR(i,laybrickPreheatHotendTemp);
EEPROM_WRITE_VAR(i,laybrickPreheatHPBTemp);
EEPROM_WRITE_VAR(i,laybrickPreheatFanSpeed);
EEPROM_WRITE_VAR(i,laywoodPreheatHotendTemp);
EEPROM_WRITE_VAR(i,laywoodPreheatHPBTemp);
EEPROM_WRITE_VAR(i,laywoodPreheatFanSpeed);
EEPROM_WRITE_VAR(i,polycarbonatePreheatHotendTemp);
EEPROM_WRITE_VAR(i,polycarbonatePreheatHPBTemp);
EEPROM_WRITE_VAR(i,polycarbonatePreheatFanSpeed);
EEPROM_WRITE_VAR(i,tglasePreheatHotendTemp);
EEPROM_WRITE_VAR(i,tglasePreheatHPBTemp);
EEPROM_WRITE_VAR(i,tglasePreheatFanSpeed);
EEPROM_WRITE_VAR(i,zprobe_zoffset);
#ifdef PIDTEMP
EEPROM_WRITE_VAR(i,Kp);
EEPROM_WRITE_VAR(i,Ki);
EEPROM_WRITE_VAR(i,Kd);
#else
float dummy = 3000.0f;
EEPROM_WRITE_VAR(i,dummy);
dummy = 0.0f;
EEPROM_WRITE_VAR(i,dummy);
EEPROM_WRITE_VAR(i,dummy);
#endif
#ifndef DOGLCD
int lcd_contrast = 32;
#endif
EEPROM_WRITE_VAR(i,lcd_contrast);
char ver2[4]=EEPROM_VERSION;
i=EEPROM_OFFSET;
EEPROM_WRITE_VAR(i,ver2); // validate data
SERIAL_ECHO_START;
SERIAL_ECHOLNPGM("Settings Stored");
}
void Config_StoreSettings() {
float dummy = 0.0f;
char ver[4] = "000";
int i = EEPROM_OFFSET;
EEPROM_WRITE_VAR(i, ver); // invalidate data first
EEPROM_WRITE_VAR(i, axis_steps_per_unit);
EEPROM_WRITE_VAR(i, max_feedrate);
EEPROM_WRITE_VAR(i, max_acceleration_units_per_sq_second);
EEPROM_WRITE_VAR(i, acceleration);
EEPROM_WRITE_VAR(i, retract_acceleration);
EEPROM_WRITE_VAR(i, minimumfeedrate);
EEPROM_WRITE_VAR(i, mintravelfeedrate);
EEPROM_WRITE_VAR(i, minsegmenttime);
EEPROM_WRITE_VAR(i, max_xy_jerk);
EEPROM_WRITE_VAR(i, max_z_jerk);
EEPROM_WRITE_VAR(i, max_e_jerk);
EEPROM_WRITE_VAR(i, add_homing);
#ifdef DELTA
EEPROM_WRITE_VAR(i, endstop_adj); // 3 floats
EEPROM_WRITE_VAR(i, delta_radius); // 1 float
EEPROM_WRITE_VAR(i, delta_diagonal_rod); // 1 float
EEPROM_WRITE_VAR(i, delta_segments_per_second); // 1 float
#else
dummy = 0.0f;
for (int q=6; q--;) EEPROM_WRITE_VAR(i, dummy);
#endif
#ifndef ULTIPANEL
int plaPreheatHotendTemp = PLA_PREHEAT_HOTEND_TEMP, plaPreheatHPBTemp = PLA_PREHEAT_HPB_TEMP, plaPreheatFanSpeed = PLA_PREHEAT_FAN_SPEED,
absPreheatHotendTemp = ABS_PREHEAT_HOTEND_TEMP, absPreheatHPBTemp = ABS_PREHEAT_HPB_TEMP, absPreheatFanSpeed = ABS_PREHEAT_FAN_SPEED;
#endif // !ULTIPANEL
EEPROM_WRITE_VAR(i, plaPreheatHotendTemp);
EEPROM_WRITE_VAR(i, plaPreheatHPBTemp);
EEPROM_WRITE_VAR(i, plaPreheatFanSpeed);
EEPROM_WRITE_VAR(i, absPreheatHotendTemp);
EEPROM_WRITE_VAR(i, absPreheatHPBTemp);
EEPROM_WRITE_VAR(i, absPreheatFanSpeed);
EEPROM_WRITE_VAR(i, zprobe_zoffset);
for (int e = 0; e < 4; e++) {
#ifdef PIDTEMP
if (e < EXTRUDERS) {
EEPROM_WRITE_VAR(i, PID_PARAM(Kp, e));
EEPROM_WRITE_VAR(i, PID_PARAM(Ki, e));
EEPROM_WRITE_VAR(i, PID_PARAM(Kd, e));
#ifdef PID_ADD_EXTRUSION_RATE
EEPROM_WRITE_VAR(i, PID_PARAM(Kc, e));
#else
dummy = 1.0f; // 1.0 = default kc
EEPROM_WRITE_VAR(i, dummy);
#endif
}
else {
#else // !PIDTEMP
{
#endif // !PIDTEMP
dummy = DUMMY_PID_VALUE;
EEPROM_WRITE_VAR(i, dummy);
dummy = 0.0f;
for (int q = 3; q--;) EEPROM_WRITE_VAR(i, dummy);
}
} // Extruders Loop
#ifndef DOGLCD
int lcd_contrast = 32;
#endif
EEPROM_WRITE_VAR(i, lcd_contrast);
#ifdef SCARA
EEPROM_WRITE_VAR(i, axis_scaling); // 3 floats
#else
dummy = 1.0f;
EEPROM_WRITE_VAR(i, dummy);
#endif
#ifdef FWRETRACT
EEPROM_WRITE_VAR(i, autoretract_enabled);
EEPROM_WRITE_VAR(i, retract_length);
#if EXTRUDERS > 1
EEPROM_WRITE_VAR(i, retract_length_swap);
#else
dummy = 0.0f;
EEPROM_WRITE_VAR(i, dummy);
#endif
EEPROM_WRITE_VAR(i, retract_feedrate);
EEPROM_WRITE_VAR(i, retract_zlift);
EEPROM_WRITE_VAR(i, retract_recover_length);
#if EXTRUDERS > 1
EEPROM_WRITE_VAR(i, retract_recover_length_swap);
#else
dummy = 0.0f;
EEPROM_WRITE_VAR(i, dummy);
#endif
EEPROM_WRITE_VAR(i, retract_recover_feedrate);
#endif // FWRETRACT
EEPROM_WRITE_VAR(i, volumetric_enabled);
// Save filament sizes
for (int q = 0; q < 4; q++) {
if (q < EXTRUDERS) dummy = filament_size[q];
EEPROM_WRITE_VAR(i, dummy);
}
int storageSize = i;
char ver2[4] = EEPROM_VERSION;
int j = EEPROM_OFFSET;
EEPROM_WRITE_VAR(j, ver2); // validate data
// Report storage size
SERIAL_ECHO_START;
SERIAL_ECHOPAIR("Settings Stored (", (unsigned long)i);
SERIAL_ECHOLNPGM(" bytes)");
}
void Config_RetrieveSettings() {
int i = EEPROM_OFFSET;
char stored_ver[4];
char ver[4] = EEPROM_VERSION;
EEPROM_READ_VAR(i, stored_ver); //read stored version
// SERIAL_ECHOLN("Version: [" << ver << "] Stored version: [" << stored_ver << "]");
if (strncmp(ver, stored_ver, 3) != 0) {
Config_ResetDefault();
}
else {
float dummy = 0;
// version number match
EEPROM_READ_VAR(i, axis_steps_per_unit);
EEPROM_READ_VAR(i, max_feedrate);
EEPROM_READ_VAR(i, max_acceleration_units_per_sq_second);
// steps per sq second need to be updated to agree with the units per sq second (as they are what is used in the planner)
reset_acceleration_rates();
EEPROM_READ_VAR(i, acceleration);
EEPROM_READ_VAR(i, retract_acceleration);
EEPROM_READ_VAR(i, minimumfeedrate);
EEPROM_READ_VAR(i, mintravelfeedrate);
EEPROM_READ_VAR(i, minsegmenttime);
EEPROM_READ_VAR(i, max_xy_jerk);
EEPROM_READ_VAR(i, max_z_jerk);
EEPROM_READ_VAR(i, max_e_jerk);
EEPROM_READ_VAR(i, add_homing);
#ifdef DELTA
EEPROM_READ_VAR(i, endstop_adj); // 3 floats
EEPROM_READ_VAR(i, delta_radius); // 1 float
EEPROM_READ_VAR(i, delta_diagonal_rod); // 1 float
EEPROM_READ_VAR(i, delta_segments_per_second); // 1 float
#else
for (int q=6; q--;) EEPROM_READ_VAR(i, dummy);
#endif
#ifndef ULTIPANEL
int plaPreheatHotendTemp, plaPreheatHPBTemp, plaPreheatFanSpeed,
absPreheatHotendTemp, absPreheatHPBTemp, absPreheatFanSpeed;
#endif
EEPROM_READ_VAR(i, plaPreheatHotendTemp);
EEPROM_READ_VAR(i, plaPreheatHPBTemp);
EEPROM_READ_VAR(i, plaPreheatFanSpeed);
EEPROM_READ_VAR(i, absPreheatHotendTemp);
EEPROM_READ_VAR(i, absPreheatHPBTemp);
EEPROM_READ_VAR(i, absPreheatFanSpeed);
EEPROM_READ_VAR(i, zprobe_zoffset);
#ifdef PIDTEMP
for (int e = 0; e < 4; e++) { // 4 = max extruders currently supported by Marlin
EEPROM_READ_VAR(i, dummy);
if (e < EXTRUDERS && dummy != DUMMY_PID_VALUE) {
// do not need to scale PID values as the values in EEPROM are already scaled
PID_PARAM(Kp, e) = dummy;
EEPROM_READ_VAR(i, PID_PARAM(Ki, e));
EEPROM_READ_VAR(i, PID_PARAM(Kd, e));
#ifdef PID_ADD_EXTRUSION_RATE
EEPROM_READ_VAR(i, PID_PARAM(Kc, e));
#else
EEPROM_READ_VAR(i, dummy);
#endif
}
else {
for (int q=3; q--;) EEPROM_READ_VAR(i, dummy); // Ki, Kd, Kc
}
}
#else // !PIDTEMP
// 4 x 4 = 16 slots for PID parameters
for (int q=16; q--;) EEPROM_READ_VAR(i, dummy); // 4x Kp, Ki, Kd, Kc
#endif // !PIDTEMP
#ifndef DOGLCD
int lcd_contrast;
#endif
EEPROM_READ_VAR(i, lcd_contrast);
#ifdef SCARA
EEPROM_READ_VAR(i, axis_scaling); // 3 floats
#else
EEPROM_READ_VAR(i, dummy);
#endif
#ifdef FWRETRACT
EEPROM_READ_VAR(i, autoretract_enabled);
EEPROM_READ_VAR(i, retract_length);
#if EXTRUDERS > 1
EEPROM_READ_VAR(i, retract_length_swap);
#else
EEPROM_READ_VAR(i, dummy);
#endif
EEPROM_READ_VAR(i, retract_feedrate);
EEPROM_READ_VAR(i, retract_zlift);
EEPROM_READ_VAR(i, retract_recover_length);
#if EXTRUDERS > 1
EEPROM_READ_VAR(i, retract_recover_length_swap);
#else
EEPROM_READ_VAR(i, dummy);
#endif
EEPROM_READ_VAR(i, retract_recover_feedrate);
#endif // FWRETRACT
EEPROM_READ_VAR(i, volumetric_enabled);
for (int q = 0; q < 4; q++) {
EEPROM_READ_VAR(i, dummy);
if (q < EXTRUDERS) filament_size[q] = dummy;
}
calculate_volumetric_multipliers();
// Call updatePID (similar to when we have processed M301)
updatePID();
// Report settings retrieved and length
SERIAL_ECHO_START;
SERIAL_ECHO(ver);
SERIAL_ECHOPAIR(" stored settings retrieved (", (unsigned long)i);
SERIAL_ECHOLNPGM(" bytes)");
}
#ifdef EEPROM_CHITCHAT
Config_PrintSettings();
#endif
}
void Config_StoreSettings()
{
char ver[4]= "000";
int i=EEPROM_OFFSET;
EEPROM_WRITE_VAR(i,ver); // invalidate data first
EEPROM_WRITE_VAR(i,axis_steps_per_unit);
EEPROM_WRITE_VAR(i,max_feedrate);
EEPROM_WRITE_VAR(i,max_acceleration_units_per_sq_second);
EEPROM_WRITE_VAR(i,acceleration);
EEPROM_WRITE_VAR(i,retract_acceleration);
EEPROM_WRITE_VAR(i,minimumfeedrate);
EEPROM_WRITE_VAR(i,mintravelfeedrate);
EEPROM_WRITE_VAR(i,minsegmenttime);
EEPROM_WRITE_VAR(i,max_xy_jerk);
EEPROM_WRITE_VAR(i,max_z_jerk);
EEPROM_WRITE_VAR(i,max_e_jerk);
EEPROM_WRITE_VAR(i,add_homeing);
#ifndef ULTIPANEL
int plaPreheatHotendTemp = PLA_PREHEAT_HOTEND_TEMP, plaPreheatHPBTemp = PLA_PREHEAT_HPB_TEMP, plaPreheatFanSpeed = PLA_PREHEAT_FAN_SPEED;
int absPreheatHotendTemp = ABS_PREHEAT_HOTEND_TEMP, absPreheatHPBTemp = ABS_PREHEAT_HPB_TEMP, absPreheatFanSpeed = ABS_PREHEAT_FAN_SPEED;
#endif
EEPROM_WRITE_VAR(i,plaPreheatHotendTemp);
EEPROM_WRITE_VAR(i,plaPreheatHPBTemp);
EEPROM_WRITE_VAR(i,plaPreheatFanSpeed);
EEPROM_WRITE_VAR(i,absPreheatHotendTemp);
EEPROM_WRITE_VAR(i,absPreheatHPBTemp);
EEPROM_WRITE_VAR(i,absPreheatFanSpeed);
#ifdef PIDTEMP
EEPROM_WRITE_VAR(i,Kp);
EEPROM_WRITE_VAR(i,Ki);
EEPROM_WRITE_VAR(i,Kd);
#else
float dummy = 3000.0f;
EEPROM_WRITE_VAR(i,dummy);
dummy = 0.0f;
EEPROM_WRITE_VAR(i,dummy);
EEPROM_WRITE_VAR(i,dummy);
#endif
EEPROM_WRITE_VAR(i,motor_current_setting);
#ifdef ENABLE_ULTILCD2
EEPROM_WRITE_VAR(i,led_brightness_level);
EEPROM_WRITE_VAR(i,led_mode);
#else
uint8_t dummyByte=0;
EEPROM_WRITE_VAR(i,dummyByte);
EEPROM_WRITE_VAR(i,dummyByte);
#endif
EEPROM_WRITE_VAR(i,retract_length);
EEPROM_WRITE_VAR(i,retract_feedrate);
char ver2[4]=EEPROM_VERSION;
i=EEPROM_OFFSET;
EEPROM_WRITE_VAR(i,ver2); // validate data
SERIAL_ECHO_START;
SERIAL_ECHOLNPGM("Settings Stored");
}
void Config_StoreSettings()
{
char ver[4]= "000";
int i=EEPROM_OFFSET;
EEPROM_WRITE_VAR(i,ver); // invalidate data first
EEPROM_WRITE_VAR(i,axis_steps_per_unit);
EEPROM_WRITE_VAR(i,max_feedrate);
EEPROM_WRITE_VAR(i,max_acceleration_units_per_sq_second);
EEPROM_WRITE_VAR(i,acceleration);
EEPROM_WRITE_VAR(i,retract_acceleration);
EEPROM_WRITE_VAR(i,minimumfeedrate);
EEPROM_WRITE_VAR(i,mintravelfeedrate);
EEPROM_WRITE_VAR(i,minsegmenttime);
EEPROM_WRITE_VAR(i,max_xy_jerk);
EEPROM_WRITE_VAR(i,max_z_jerk);
EEPROM_WRITE_VAR(i,max_e_jerk);
EEPROM_WRITE_VAR(i,add_homeing);
//Changes Rapduch
#ifdef HYSTERESIS_H
EEPROM_WRITE_VAR(i,menu_hysteresis_X);
EEPROM_WRITE_VAR(i,menu_hysteresis_Y);
#endif
#ifndef ULTIPANEL
int plaPreheatHotendTemp = PLA_PREHEAT_HOTEND_TEMP, plaPreheatHPBTemp = PLA_PREHEAT_HPB_TEMP, plaPreheatFanSpeed = PLA_PREHEAT_FAN_SPEED;
int absPreheatHotendTemp = ABS_PREHEAT_HOTEND_TEMP, absPreheatHPBTemp = ABS_PREHEAT_HPB_TEMP, absPreheatFanSpeed = ABS_PREHEAT_FAN_SPEED;
int nylonPreheatHotendTemp = NYLON_PREHEAT_HOTEND_TEMP, nylonPreheatHPBTemp = NYLON_PREHEAT_HPB_TEMP, nylonPreheatFanSpeed = NYLON_PREHEAT_FAN_SPEED;
int pvaPreheatHotendTemp = PVA_PREHEAT_HOTEND_TEMP, pvaPreheatHPBTemp = PVA_PREHEAT_HPB_TEMP, pvaPreheatFanSpeed = PVA_PREHEAT_FAN_SPEED;
//int laywoodPreheatHotendTemp = LAYWOOD_PREHEAT_HOTEND_TEMP, laywoodPreheatHPBTemp = LAYWOOD_PREHEAT_HPB_TEMP, laywoodPreheatFanSpeed = LAYWOOD_PREHEAT_FAN_SPEED;
// int laybrickPreheatHotendTemp = LAYBRICK_PREHEAT_HOTEND_TEMP, laybrickPreheatHPBTemp = LAYBRICK_PREHEAT_HPB_TEMP, laybrickPreheatFanSpeed = LAYBRICK_PREHEAT_FAN_SPEED;
#endif
EEPROM_WRITE_VAR(i,plaPreheatHotendTemp);
EEPROM_WRITE_VAR(i,plaPreheatHPBTemp);
EEPROM_WRITE_VAR(i,plaPreheatFanSpeed);
EEPROM_WRITE_VAR(i,absPreheatHotendTemp);
EEPROM_WRITE_VAR(i,absPreheatHPBTemp);
EEPROM_WRITE_VAR(i,absPreheatFanSpeed);
EEPROM_WRITE_VAR(i,nylonPreheatHotendTemp);
EEPROM_WRITE_VAR(i,nylonPreheatHPBTemp);
EEPROM_WRITE_VAR(i,nylonPreheatFanSpeed);
EEPROM_WRITE_VAR(i,pvaPreheatHotendTemp);
EEPROM_WRITE_VAR(i,pvaPreheatHPBTemp);
EEPROM_WRITE_VAR(i,pvaPreheatFanSpeed);
EEPROM_WRITE_VAR(i,laywoodPreheatHotendTemp);
EEPROM_WRITE_VAR(i,laywoodPreheatHPBTemp);
EEPROM_WRITE_VAR(i,laywoodPreheatFanSpeed);
EEPROM_WRITE_VAR(i,laybrickPreheatHotendTemp);
EEPROM_WRITE_VAR(i,laybrickPreheatHPBTemp);
EEPROM_WRITE_VAR(i,laybrickPreheatFanSpeed);
#ifdef PIDTEMP
EEPROM_WRITE_VAR(i,Kp);
EEPROM_WRITE_VAR(i,Ki);
EEPROM_WRITE_VAR(i,Kd);
#else
float dummy = 3000.0f;
EEPROM_WRITE_VAR(i,dummy);
dummy = 0.0f;
EEPROM_WRITE_VAR(i,dummy);
EEPROM_WRITE_VAR(i,dummy);
#endif
char ver2[4]=EEPROM_VERSION;
i=EEPROM_OFFSET;
EEPROM_WRITE_VAR(i,ver2); // validate data
SERIAL_ECHO_START;
SERIAL_ECHOLNPGM("Settings Stored");
}
/**
* M500 - Store Configuration
*/
void Config_StoreSettings() {
float dummy = 0.0f;
char ver[6] = "00000";
int i = EEPROM_OFFSET;
EEPROM_WRITE_VAR(i, ver); // invalidate data first
i += sizeof(eeprom_checksum); // Skip the checksum slot
eeprom_checksum = 0; // clear before first "real data"
EEPROM_WRITE_VAR(i, planner.axis_steps_per_mm);
EEPROM_WRITE_VAR(i, planner.max_feedrate);
EEPROM_WRITE_VAR(i, planner.max_acceleration_mm_per_s2);
EEPROM_WRITE_VAR(i, planner.acceleration);
EEPROM_WRITE_VAR(i, planner.retract_acceleration);
EEPROM_WRITE_VAR(i, planner.travel_acceleration);
EEPROM_WRITE_VAR(i, planner.min_feedrate);
EEPROM_WRITE_VAR(i, planner.min_travel_feedrate);
EEPROM_WRITE_VAR(i, planner.min_segment_time);
EEPROM_WRITE_VAR(i, planner.max_xy_jerk);
EEPROM_WRITE_VAR(i, planner.max_z_jerk);
EEPROM_WRITE_VAR(i, planner.max_e_jerk);
EEPROM_WRITE_VAR(i, home_offset);
EEPROM_WRITE_VAR(i, hotend_offset);
#if ENABLED(MESH_BED_LEVELING)
// Compile time test that sizeof(mbl.z_values) is as expected
typedef char c_assert[(sizeof(mbl.z_values) == (MESH_NUM_X_POINTS) * (MESH_NUM_Y_POINTS) * sizeof(dummy)) ? 1 : -1];
uint8_t mesh_num_x = MESH_NUM_X_POINTS,
mesh_num_y = MESH_NUM_Y_POINTS,
dummy_uint8 = mbl.status & _BV(MBL_STATUS_HAS_MESH_BIT);
EEPROM_WRITE_VAR(i, dummy_uint8);
EEPROM_WRITE_VAR(i, mbl.z_offset);
EEPROM_WRITE_VAR(i, mesh_num_x);
EEPROM_WRITE_VAR(i, mesh_num_y);
EEPROM_WRITE_VAR(i, mbl.z_values);
#endif
#if HEATER_USES_AD595
EEPROM_WRITE_VAR(i, ad595_offset);
EEPROM_WRITE_VAR(i, ad595_gain);
#endif
#if MECH(DELTA)
EEPROM_WRITE_VAR(i, endstop_adj);
EEPROM_WRITE_VAR(i, delta_radius);
EEPROM_WRITE_VAR(i, delta_diagonal_rod);
EEPROM_WRITE_VAR(i, sw_endstop_max);
EEPROM_WRITE_VAR(i, tower_adj);
EEPROM_WRITE_VAR(i, diagrod_adj);
#elif ENABLED(Z_DUAL_ENDSTOPS)
EEPROM_WRITE_VAR(i, z_endstop_adj);
#endif
#if HASNT(BED_PROBE)
float zprobe_zoffset = 0;
#endif
EEPROM_WRITE_VAR(i, zprobe_zoffset);
#if DISABLED(ULTIPANEL)
int plaPreheatHotendTemp = PLA_PREHEAT_HOTEND_TEMP, plaPreheatHPBTemp = PLA_PREHEAT_HPB_TEMP, plaPreheatFanSpeed = PLA_PREHEAT_FAN_SPEED,
absPreheatHotendTemp = ABS_PREHEAT_HOTEND_TEMP, absPreheatHPBTemp = ABS_PREHEAT_HPB_TEMP, absPreheatFanSpeed = ABS_PREHEAT_FAN_SPEED,
gumPreheatHotendTemp = GUM_PREHEAT_HOTEND_TEMP, gumPreheatHPBTemp = GUM_PREHEAT_HPB_TEMP, gumPreheatFanSpeed = GUM_PREHEAT_FAN_SPEED;
#endif
EEPROM_WRITE_VAR(i, plaPreheatHotendTemp);
EEPROM_WRITE_VAR(i, plaPreheatHPBTemp);
EEPROM_WRITE_VAR(i, plaPreheatFanSpeed);
EEPROM_WRITE_VAR(i, absPreheatHotendTemp);
EEPROM_WRITE_VAR(i, absPreheatHPBTemp);
EEPROM_WRITE_VAR(i, absPreheatFanSpeed);
EEPROM_WRITE_VAR(i, gumPreheatHotendTemp);
EEPROM_WRITE_VAR(i, gumPreheatHPBTemp);
EEPROM_WRITE_VAR(i, gumPreheatFanSpeed);
#if ENABLED(PIDTEMP)
for (int h = 0; h < HOTENDS; h++) {
EEPROM_WRITE_VAR(i, PID_PARAM(Kp, h));
EEPROM_WRITE_VAR(i, PID_PARAM(Ki, h));
EEPROM_WRITE_VAR(i, PID_PARAM(Kd, h));
EEPROM_WRITE_VAR(i, PID_PARAM(Kc, h));
}
#endif
#if DISABLED(PID_ADD_EXTRUSION_RATE)
int lpq_len = 20;
#endif
EEPROM_WRITE_VAR(i, lpq_len);
#if ENABLED(PIDTEMPBED)
EEPROM_WRITE_VAR(i, bedKp);
EEPROM_WRITE_VAR(i, bedKi);
EEPROM_WRITE_VAR(i, bedKd);
#endif
#if ENABLED(PIDTEMPCHAMBER)
EEPROM_WRITE_VAR(i, chamberKp);
EEPROM_WRITE_VAR(i, chamberKi);
EEPROM_WRITE_VAR(i, chamberKd);
#endif
#if ENABLED(PIDTEMPCOOLER)
EEPROM_WRITE_VAR(i, coolerKp);
EEPROM_WRITE_VAR(i, coolerKi);
EEPROM_WRITE_VAR(i, coolerKd);
#endif
#if HASNT(LCD_CONTRAST)
const int lcd_contrast = 32;
#endif
EEPROM_WRITE_VAR(i, lcd_contrast);
#if MECH(SCARA)
EEPROM_WRITE_VAR(i, axis_scaling); // 3 floats
#endif
#if ENABLED(FWRETRACT)
EEPROM_WRITE_VAR(i, autoretract_enabled);
EEPROM_WRITE_VAR(i, retract_length);
#if EXTRUDERS > 1
EEPROM_WRITE_VAR(i, retract_length_swap);
#else
dummy = 0.0f;
EEPROM_WRITE_VAR(i, dummy);
#endif
EEPROM_WRITE_VAR(i, retract_feedrate);
EEPROM_WRITE_VAR(i, retract_zlift);
EEPROM_WRITE_VAR(i, retract_recover_length);
#if EXTRUDERS > 1
EEPROM_WRITE_VAR(i, retract_recover_length_swap);
#else
dummy = 0.0f;
EEPROM_WRITE_VAR(i, dummy);
#endif
EEPROM_WRITE_VAR(i, retract_recover_feedrate);
#endif // FWRETRACT
EEPROM_WRITE_VAR(i, volumetric_enabled);
// Save filament sizes
for (int e = 0; e < EXTRUDERS; e++)
EEPROM_WRITE_VAR(i, filament_size[e]);
#if ENABLED(IDLE_OOZING_PREVENT)
EEPROM_WRITE_VAR(i, IDLE_OOZING_enabled);
#endif
#if MB(ALLIGATOR)
EEPROM_WRITE_VAR(i, motor_current);
#endif
uint16_t final_checksum = eeprom_checksum;
int j = EEPROM_OFFSET;
EEPROM_WRITE_VAR(j, version);
EEPROM_WRITE_VAR(j, final_checksum);
// Report storage size
ECHO_SMV(DB, "Settings Stored (", i);
ECHO_EM(" bytes)");
}
void Config_StoreSettings()
{
char ver[4]= "000";
int i=EEPROM_OFFSET;
EEPROM_WRITE_VAR(i,ver); // invalidate data first
EEPROM_WRITE_VAR(i,axis_steps_per_unit);
EEPROM_WRITE_VAR(i,max_feedrate);
EEPROM_WRITE_VAR(i,max_acceleration_units_per_sq_second);
EEPROM_WRITE_VAR(i,acceleration);
EEPROM_WRITE_VAR(i,retract_acceleration);
EEPROM_WRITE_VAR(i,minimumfeedrate);
EEPROM_WRITE_VAR(i,mintravelfeedrate);
EEPROM_WRITE_VAR(i,minsegmenttime);
EEPROM_WRITE_VAR(i,max_xy_jerk);
EEPROM_WRITE_VAR(i,max_z_jerk);
EEPROM_WRITE_VAR(i,max_e_jerk);
EEPROM_WRITE_VAR(i,add_homeing);
#ifndef ULTIPANEL
int plaPreheatHotendTemp = PLA_PREHEAT_HOTEND_TEMP, plaPreheatHPBTemp = PLA_PREHEAT_HPB_TEMP, plaPreheatFanSpeed = PLA_PREHEAT_FAN_SPEED;
int absPreheatHotendTemp = ABS_PREHEAT_HOTEND_TEMP, absPreheatHPBTemp = ABS_PREHEAT_HPB_TEMP, absPreheatFanSpeed = ABS_PREHEAT_FAN_SPEED;
#endif
EEPROM_WRITE_VAR(i,plaPreheatHotendTemp);
EEPROM_WRITE_VAR(i,plaPreheatHPBTemp);
EEPROM_WRITE_VAR(i,plaPreheatFanSpeed);
EEPROM_WRITE_VAR(i,absPreheatHotendTemp);
EEPROM_WRITE_VAR(i,absPreheatHPBTemp);
EEPROM_WRITE_VAR(i,absPreheatFanSpeed);
#ifdef PIDTEMP
EEPROM_WRITE_VAR(i,Kp);
EEPROM_WRITE_VAR(i,Ki);
EEPROM_WRITE_VAR(i,Kd);
#else
EEPROM_WRITE_VAR(i,3000);
EEPROM_WRITE_VAR(i,0);
EEPROM_WRITE_VAR(i,0);
#endif
char ver2[4]=EEPROM_VERSION;
i=EEPROM_OFFSET;
EEPROM_WRITE_VAR(i,ver2); // validate data
SERIAL_ECHO_START;
SERIAL_ECHOLNPGM("Settings Stored");
}
void setDefault_plan()
{
float tmp1[] = DEFAULT_AXIS_STEPS_PER_UNIT;
float tmp2[] = DEFAULT_MAX_FEEDRATE;
long tmp3[] = DEFAULT_MAX_ACCELERATION;
for (short i=0;i<4;i++){
axis_steps_per_unit[i] = tmp1[i];
max_feedrate[i] = tmp2[i];
max_acceleration_units_per_sq_second[i] = tmp3[i];
}
// steps per sq second need to be updated to agree with the units per sq second
reset_acceleration_rates();
acceleration = DEFAULT_ACCELERATION;
retract_acceleration = DEFAULT_RETRACT_ACCELERATION;
minimumfeedrate = DEFAULT_MINIMUMFEEDRATE;
minsegmenttime = DEFAULT_MINSEGMENTTIME;
mintravelfeedrate = DEFAULT_MINTRAVELFEEDRATE;
max_xy_jerk = DEFAULT_XYJERK;
max_z_jerk = DEFAULT_ZJERK;
max_e_jerk = DEFAULT_EJERK;
EEPROM_WRITE_VAR(eeprom_offsets::AXIS_STEPS_PER_UNIT, axis_steps_per_unit);
EEPROM_WRITE_VAR(eeprom_offsets::MAX_FEEDRATE, max_feedrate);
EEPROM_WRITE_VAR(eeprom_offsets::MAX_ACCELERATION, max_acceleration_units_per_sq_second);
EEPROM_WRITE_VAR(eeprom_offsets::ACCELERATION, acceleration);
EEPROM_WRITE_VAR(eeprom_offsets::RETRACT_ACCELERATION, retract_acceleration);
EEPROM_WRITE_VAR(eeprom_offsets::MINIMUMFEEDRATE, minimumfeedrate);
EEPROM_WRITE_VAR(eeprom_offsets::MINTRAVELFEEDRATE, mintravelfeedrate);
EEPROM_WRITE_VAR(eeprom_offsets::MINSEGMENTTIME, minsegmenttime);
EEPROM_WRITE_VAR(eeprom_offsets::MAX_XYJERK, max_xy_jerk);
EEPROM_WRITE_VAR(eeprom_offsets::MAX_ZJERK, max_z_jerk);
EEPROM_WRITE_VAR(eeprom_offsets::MAX_EJERK, max_e_jerk);
}
void setCustom_addHoming(float* add_homing)
{
EEPROM_WRITE_VAR(eeprom_offsets::ADD_HOMING, command::add_homing);
}
void Config_StoreSettings()
{
char ver[4]= "000";
int i=EEPROM_OFFSET;
EEPROM_WRITE_VAR(i,ver); // invalidate data first
EEPROM_WRITE_VAR(i,axis_steps_per_unit);
EEPROM_WRITE_VAR(i,max_feedrate);
EEPROM_WRITE_VAR(i,max_acceleration_units_per_sq_second);
EEPROM_WRITE_VAR(i,acceleration);
EEPROM_WRITE_VAR(i,retract_acceleration);
EEPROM_WRITE_VAR(i,minimumfeedrate);
EEPROM_WRITE_VAR(i,mintravelfeedrate);
EEPROM_WRITE_VAR(i,minsegmenttime);
EEPROM_WRITE_VAR(i,max_xy_jerk);
EEPROM_WRITE_VAR(i,max_z_jerk);
EEPROM_WRITE_VAR(i,max_e_jerk);
EEPROM_WRITE_VAR(i,add_homing);
#ifdef DELTA
EEPROM_WRITE_VAR(i,endstop_adj);
EEPROM_WRITE_VAR(i,delta_radius);
EEPROM_WRITE_VAR(i,delta_diagonal_rod);
EEPROM_WRITE_VAR(i,delta_segments_per_second);
#endif
#ifndef ULTIPANEL
int plaPreheatHotendTemp = PLA_PREHEAT_HOTEND_TEMP, plaPreheatHPBTemp = PLA_PREHEAT_HPB_TEMP, plaPreheatFanSpeed = PLA_PREHEAT_FAN_SPEED;
int absPreheatHotendTemp = ABS_PREHEAT_HOTEND_TEMP, absPreheatHPBTemp = ABS_PREHEAT_HPB_TEMP, absPreheatFanSpeed = ABS_PREHEAT_FAN_SPEED;
#endif
EEPROM_WRITE_VAR(i,plaPreheatHotendTemp);
EEPROM_WRITE_VAR(i,plaPreheatHPBTemp);
EEPROM_WRITE_VAR(i,plaPreheatFanSpeed);
EEPROM_WRITE_VAR(i,absPreheatHotendTemp);
EEPROM_WRITE_VAR(i,absPreheatHPBTemp);
EEPROM_WRITE_VAR(i,absPreheatFanSpeed);
EEPROM_WRITE_VAR(i,zprobe_zoffset);
#ifdef PIDTEMP
EEPROM_WRITE_VAR(i,Kp);
EEPROM_WRITE_VAR(i,Ki);
EEPROM_WRITE_VAR(i,Kd);
#else
float dummy = 3000.0f;
EEPROM_WRITE_VAR(i,dummy);
dummy = 0.0f;
EEPROM_WRITE_VAR(i,dummy);
EEPROM_WRITE_VAR(i,dummy);
#endif
#ifndef DOGLCD
int lcd_contrast = 32;
#endif
EEPROM_WRITE_VAR(i,lcd_contrast);
#ifdef SCARA
EEPROM_WRITE_VAR(i,axis_scaling); // Add scaling for SCARA
#endif
#ifdef FWRETRACT
EEPROM_WRITE_VAR(i,autoretract_enabled);
EEPROM_WRITE_VAR(i,retract_length);
#if EXTRUDERS > 1
EEPROM_WRITE_VAR(i,retract_length_swap);
#endif
EEPROM_WRITE_VAR(i,retract_feedrate);
EEPROM_WRITE_VAR(i,retract_zlift);
EEPROM_WRITE_VAR(i,retract_recover_length);
#if EXTRUDERS > 1
EEPROM_WRITE_VAR(i,retract_recover_length_swap);
#endif
EEPROM_WRITE_VAR(i,retract_recover_feedrate);
#endif
// Save filament sizes
EEPROM_WRITE_VAR(i, volumetric_enabled);
EEPROM_WRITE_VAR(i, filament_size[0]);
#if EXTRUDERS > 1
EEPROM_WRITE_VAR(i, filament_size[1]);
#if EXTRUDERS > 2
EEPROM_WRITE_VAR(i, filament_size[2]);
#endif
#endif
char ver2[4]=EEPROM_VERSION;
i=EEPROM_OFFSET;
EEPROM_WRITE_VAR(i,ver2); // validate data
SERIAL_ECHO_START;
SERIAL_ECHOLNPGM("Settings Stored");
}
void Config_StoreSettings() {
float dummy = 0.0f;
char ver[7] = "000000";
int i = EEPROM_OFFSET;
EEPROM_WRITE_VAR(i, ver); // invalidate data first
EEPROM_WRITE_VAR(i, axis_steps_per_unit);
EEPROM_WRITE_VAR(i, max_feedrate);
EEPROM_WRITE_VAR(i, max_acceleration_units_per_sq_second);
EEPROM_WRITE_VAR(i, acceleration);
EEPROM_WRITE_VAR(i, retract_acceleration);
EEPROM_WRITE_VAR(i, travel_acceleration);
EEPROM_WRITE_VAR(i, minimumfeedrate);
EEPROM_WRITE_VAR(i, mintravelfeedrate);
EEPROM_WRITE_VAR(i, minsegmenttime);
EEPROM_WRITE_VAR(i, max_xy_jerk);
EEPROM_WRITE_VAR(i, max_z_jerk);
EEPROM_WRITE_VAR(i, max_e_jerk);
EEPROM_WRITE_VAR(i, home_offset);
EEPROM_WRITE_VAR(i, hotend_offset);
#if !MECH(DELTA)
EEPROM_WRITE_VAR(i, zprobe_zoffset);
#endif
#if HEATER_USES_AD595
EEPROM_WRITE_VAR(i, ad595_offset);
EEPROM_WRITE_VAR(i, ad595_gain);
#endif
#if MECH(DELTA)
EEPROM_WRITE_VAR(i, endstop_adj);
EEPROM_WRITE_VAR(i, delta_radius);
EEPROM_WRITE_VAR(i, delta_diagonal_rod);
EEPROM_WRITE_VAR(i, sw_endstop_max);
EEPROM_WRITE_VAR(i, tower_adj);
EEPROM_WRITE_VAR(i, diagrod_adj);
EEPROM_WRITE_VAR(i, z_probe_offset);
#elif ENABLED(Z_DUAL_ENDSTOPS)
EEPROM_WRITE_VAR(i, z_endstop_adj); // 1 floats
#endif
#if DISABLED(ULTIPANEL)
int plaPreheatHotendTemp = PLA_PREHEAT_HOTEND_TEMP, plaPreheatHPBTemp = PLA_PREHEAT_HPB_TEMP, plaPreheatFanSpeed = PLA_PREHEAT_FAN_SPEED,
absPreheatHotendTemp = ABS_PREHEAT_HOTEND_TEMP, absPreheatHPBTemp = ABS_PREHEAT_HPB_TEMP, absPreheatFanSpeed = ABS_PREHEAT_FAN_SPEED,
gumPreheatHotendTemp = GUM_PREHEAT_HOTEND_TEMP, gumPreheatHPBTemp = GUM_PREHEAT_HPB_TEMP, gumPreheatFanSpeed = GUM_PREHEAT_FAN_SPEED;
#endif
EEPROM_WRITE_VAR(i, plaPreheatHotendTemp);
EEPROM_WRITE_VAR(i, plaPreheatHPBTemp);
EEPROM_WRITE_VAR(i, plaPreheatFanSpeed);
EEPROM_WRITE_VAR(i, absPreheatHotendTemp);
EEPROM_WRITE_VAR(i, absPreheatHPBTemp);
EEPROM_WRITE_VAR(i, absPreheatFanSpeed);
EEPROM_WRITE_VAR(i, gumPreheatHotendTemp);
EEPROM_WRITE_VAR(i, gumPreheatHPBTemp);
EEPROM_WRITE_VAR(i, gumPreheatFanSpeed);
#if ENABLED(PIDTEMP)
for (int h = 0; h < HOTENDS; h++) {
EEPROM_WRITE_VAR(i, PID_PARAM(Kp, h));
EEPROM_WRITE_VAR(i, PID_PARAM(Ki, h));
EEPROM_WRITE_VAR(i, PID_PARAM(Kd, h));
EEPROM_WRITE_VAR(i, PID_PARAM(Kc, h));
}
#endif
#if DISABLED(PID_ADD_EXTRUSION_RATE)
int lpq_len = 20;
#endif
EEPROM_WRITE_VAR(i, lpq_len);
#if ENABLED(PIDTEMPBED)
EEPROM_WRITE_VAR(i, bedKp);
EEPROM_WRITE_VAR(i, bedKi);
EEPROM_WRITE_VAR(i, bedKd);
#endif
#if HASNT(LCD_CONTRAST)
const int lcd_contrast = 32;
#endif
EEPROM_WRITE_VAR(i, lcd_contrast);
#if MECH(SCARA)
EEPROM_WRITE_VAR(i, axis_scaling); // 3 floats
#endif
#if ENABLED(FWRETRACT)
EEPROM_WRITE_VAR(i, autoretract_enabled);
EEPROM_WRITE_VAR(i, retract_length);
#if EXTRUDERS > 1
EEPROM_WRITE_VAR(i, retract_length_swap);
#else
dummy = 0.0f;
EEPROM_WRITE_VAR(i, dummy);
#endif
EEPROM_WRITE_VAR(i, retract_feedrate);
EEPROM_WRITE_VAR(i, retract_zlift);
EEPROM_WRITE_VAR(i, retract_recover_length);
#if EXTRUDERS > 1
EEPROM_WRITE_VAR(i, retract_recover_length_swap);
#else
dummy = 0.0f;
EEPROM_WRITE_VAR(i, dummy);
#endif
EEPROM_WRITE_VAR(i, retract_recover_feedrate);
#endif // FWRETRACT
EEPROM_WRITE_VAR(i, volumetric_enabled);
// Save filament sizes
for (int e = 0; e < EXTRUDERS; e++)
EEPROM_WRITE_VAR(i, filament_size[e]);
#if ENABLED(IDLE_OOZING_PREVENT)
EEPROM_WRITE_VAR(i, IDLE_OOZING_enabled);
#endif
#if MB(ALLIGATOR)
EEPROM_WRITE_VAR(i, motor_current);
#endif
char ver2[7] = EEPROM_VERSION;
int j = EEPROM_OFFSET;
EEPROM_WRITE_VAR(j, ver2); // validate data
// Report storage size
ECHO_SMV(DB, "Settings Stored (", (unsigned long)i);
ECHO_EM(" bytes)");
}