//*****************************************************************************
//
//! Enable the RGB LED with already configured timer settings
//!
//! This function or RGBDisable should be called during application
//! initialization to configure the GPIO pins to which the LEDs are attached.
//! This function enables the timers and configures the GPIO pins as timer
//! outputs.
//!
//! \return None.
//
//*****************************************************************************
void
RGBEnable(void)
{
//
// Enable timers to begin counting
//
TimerEnable(RED_TIMER_BASE, TIMER_BOTH);
TimerEnable(GREEN_TIMER_BASE, TIMER_BOTH);
TimerEnable(BLUE_TIMER_BASE, TIMER_BOTH);
//
// Reconfigure each LED's GPIO pad for timer control
//
GPIOPinConfigure(GREEN_GPIO_PIN_CFG);
GPIOPinTypeTimer(GREEN_GPIO_BASE, GREEN_GPIO_PIN);
GPIOPadConfigSet(GREEN_GPIO_BASE, GREEN_GPIO_PIN, GPIO_STRENGTH_8MA_SC,
GPIO_PIN_TYPE_STD);
GPIOPinConfigure(BLUE_GPIO_PIN_CFG);
GPIOPinTypeTimer(BLUE_GPIO_BASE, BLUE_GPIO_PIN);
GPIOPadConfigSet(BLUE_GPIO_BASE, BLUE_GPIO_PIN, GPIO_STRENGTH_8MA_SC,
GPIO_PIN_TYPE_STD);
GPIOPinConfigure(RED_GPIO_PIN_CFG);
GPIOPinTypeTimer(RED_GPIO_BASE, RED_GPIO_PIN);
GPIOPadConfigSet(RED_GPIO_BASE, RED_GPIO_PIN, GPIO_STRENGTH_8MA_SC,
GPIO_PIN_TYPE_STD);
}
/*
Initializes PWM timers for ESC control
\param none
Motor 1: PB4 using TIMER1_A
Motor 2: PB5 using TIMER1_B
Motor 3: PB0 using TIMER2_A
Motor 4: PB1 using TIMER2_B
\return none
*/
void initPWM()
{
// Configure output pins
SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOB);
GPIOPinConfigure(GPIO_PB4_T1CCP0);
GPIOPinTypeTimer(GPIO_PORTB_BASE, GPIO_PIN_4);
GPIOPinConfigure(GPIO_PB5_T1CCP1);
GPIOPinTypeTimer(GPIO_PORTB_BASE, GPIO_PIN_5);
GPIOPinConfigure(GPIO_PB0_T2CCP0);
GPIOPinTypeTimer(GPIO_PORTB_BASE, GPIO_PIN_0);
GPIOPinConfigure(GPIO_PB1_T2CCP1);
GPIOPinTypeTimer(GPIO_PORTB_BASE, GPIO_PIN_1);
// Configure the two timers as half width (16bit) pwm (though we get 24 bits with the "prescale")
SysCtlPeripheralEnable(SYSCTL_PERIPH_TIMER1);
TimerConfigure(TIMER1_BASE, TIMER_CFG_SPLIT_PAIR|TIMER_CFG_A_PWM|TIMER_CFG_B_PWM);
TimerControlLevel(TIMER1_BASE, TIMER_BOTH, true);
SysCtlPeripheralEnable(SYSCTL_PERIPH_TIMER2);
TimerConfigure(TIMER2_BASE, TIMER_CFG_SPLIT_PAIR|TIMER_CFG_A_PWM|TIMER_CFG_B_PWM);
TimerControlLevel(TIMER2_BASE, TIMER_BOTH, true);
//calculate pulse repetition rate
uint32_t cycles_per_interval = SysCtlClockGet() / MOTORUPDATE /*Hz*/;
uint32_t periodl = cycles_per_interval;
uint8_t periodh = periodl >> 16;
periodl &= 0xFFFF;
//set pulse repetition rate
TimerPrescaleSet(TIMER1_BASE, TIMER_A, periodh);
TimerLoadSet(TIMER1_BASE, TIMER_A, periodl);
TimerPrescaleSet(TIMER1_BASE, TIMER_B, periodh);
TimerLoadSet(TIMER1_BASE, TIMER_B, periodl);
TimerPrescaleSet(TIMER2_BASE, TIMER_A, periodh);
TimerLoadSet(TIMER2_BASE, TIMER_A, periodl);
TimerPrescaleSet(TIMER2_BASE, TIMER_B, periodh);
TimerLoadSet(TIMER2_BASE, TIMER_B, periodl);
//set all motors to zero
motorSet(1,0);
motorSet(2,0);
motorSet(3,0);
motorSet(4,0);
//enable timers
TimerEnable(TIMER1_BASE, TIMER_A);
TimerEnable(TIMER1_BASE, TIMER_B);
TimerEnable(TIMER2_BASE, TIMER_A);
TimerEnable(TIMER2_BASE, TIMER_B);
}
void cfg_Timer()
{
uint32_t Period=800000/*(40MHz/800.000=50Hz)*/,DutyCycle=Period/2;
ROM_SysCtlClockSet(SYSCTL_SYSDIV_5|SYSCTL_USE_PLL|SYSCTL_XTAL_16MHZ|SYSCTL_OSC_MAIN); //40MHz
/*********************CONFIG_PWM_1*********************************/
SysCtlPeripheralEnable(SYSCTL_PERIPH_WTIMER0);
SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOC);
GPIOPinConfigure(GPIO_PC4_WT0CCP0);
GPIOPinTypeTimer(GPIO_PORTC_BASE, GPIO_PIN_4);
TimerConfigure(WTIMER0_BASE, TIMER_CFG_SPLIT_PAIR | TIMER_CFG_A_PWM);
TimerLoadSet(WTIMER0_BASE, TIMER_A, Period);
TimerMatchSet(WTIMER0_BASE, TIMER_A, DutyCycle);
TimerEnable(WTIMER0_BASE, TIMER_A);
/*********************CONFIG_PWM_1*********************************/
/*********************CONFIG_PWM_2*********************************/
SysCtlPeripheralEnable(SYSCTL_PERIPH_WTIMER1);
//SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOC);
GPIOPinConfigure(GPIO_PC6_WT1CCP0);
GPIOPinTypeTimer(GPIO_PORTC_BASE, GPIO_PIN_6);
TimerConfigure(WTIMER1_BASE, TIMER_CFG_SPLIT_PAIR | TIMER_CFG_A_PWM);
TimerLoadSet(WTIMER1_BASE, TIMER_A, Period);
TimerMatchSet(WTIMER1_BASE, TIMER_A, DutyCycle);
TimerEnable(WTIMER1_BASE, TIMER_A);
/********************CONFIG_PWM_2********************************
/*********************CONFIG_PWM_3*********************************/
SysCtlPeripheralEnable(SYSCTL_PERIPH_WTIMER2);
SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOD);
GPIOPinConfigure(GPIO_PD0_WT2CCP0);
GPIOPinTypeTimer(GPIO_PORTD_BASE, GPIO_PIN_0);
TimerConfigure(WTIMER2_BASE, TIMER_CFG_SPLIT_PAIR | TIMER_CFG_A_PWM);
TimerLoadSet(WTIMER2_BASE, TIMER_A, Period);
TimerMatchSet(WTIMER2_BASE, TIMER_A, DutyCycle);
TimerEnable(WTIMER2_BASE, TIMER_A);
/*********************CONFIG_PWM_3*********************************/
/*********************CONFIG_PWM_4*********************************/
SysCtlPeripheralEnable(SYSCTL_PERIPH_WTIMER3);
//SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOD);
GPIOPinConfigure(GPIO_PD2_WT3CCP0);
GPIOPinTypeTimer(GPIO_PORTD_BASE, GPIO_PIN_2);
TimerConfigure(WTIMER3_BASE, TIMER_CFG_SPLIT_PAIR | TIMER_CFG_A_PWM);
TimerLoadSet(WTIMER3_BASE, TIMER_A, Period);
TimerMatchSet(WTIMER3_BASE, TIMER_A, DutyCycle);
TimerEnable(WTIMER3_BASE, TIMER_A);
/*********************CONFIG_PWM_4*********************************/
}
static void pwm_init(void) {
uint32_t frequency = 50;
uint32_t period1 = SysCtlClockGet() / frequency;
uint32_t extender1 = period1 >> 16;
period1 &= 0xFFFF;
uint32_t period2 = SysCtlClockGet() / frequency;
uint32_t extender2 = period2 >> 16;
period2 &= 0xFFFF;
SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOB);
GPIOPinConfigure(GPIO_PB2_T3CCP0);
GPIOPinTypeTimer(GPIO_PORTB_BASE, GPIO_PIN_2);
// Configure timer
SysCtlPeripheralEnable(SYSCTL_PERIPH_TIMER3);
TimerConfigure(TIMER3_BASE, TIMER_CFG_SPLIT_PAIR|TIMER_CFG_A_PWM);
HWREG(TIMER3_BASE + TIMER_O_CTL) |= (TIMER_CTL_TAPWML);
//set period
TimerPrescaleSet(TIMER3_BASE, TIMER_A, extender1);
TimerLoadSet(TIMER3_BASE, TIMER_A, period1);
//set default value A
TimerPrescaleMatchSet(TIMER3_BASE, TIMER_A, extender2);
TimerMatchSet(TIMER3_BASE, TIMER_A, period2);
TimerEnable(TIMER3_BASE, TIMER_A);
}
// WTimer1A is used to measure the width of the pulses
// WTimer1B is used to turn off motors if the connection to the RX is lost
void initRX(void) {
SysCtlPeripheralEnable(SYSCTL_PERIPH_WTIMER1); // Enable Wide Timer1 peripheral
SysCtlDelay(2); // Insert a few cycles after enabling the peripheral to allow the clock to be fully activated
SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOC); // Enable GPIOC peripheral
SysCtlDelay(2); // Insert a few cycles after enabling the peripheral to allow the clock to be fully activated
GPIOPinConfigure(GPIO_PC6_WT1CCP0); // Use alternate function
GPIOPinTypeTimer(GPIO_PORTC_BASE, GPIO_PIN_6); // Use pin with timer peripheral
// Split timers and enable timer A event up-count timer and timer B as a periodic timer
TimerConfigure(WTIMER1_BASE, TIMER_CFG_SPLIT_PAIR | TIMER_CFG_A_CAP_TIME_UP | TIMER_CFG_B_PERIODIC);
// Configure WTimer1A
TimerControlEvent(WTIMER1_BASE, TIMER_A, TIMER_EVENT_BOTH_EDGES); // Interrupt on both edges
TimerIntRegister(WTIMER1_BASE, TIMER_A, CaptureHandler); // Register interrupt handler
TimerIntEnable(WTIMER1_BASE, TIMER_CAPA_EVENT); // Enable timer capture A event interrupt
IntPrioritySet(INT_WTIMER1A, 0); // Configure Wide Timer 1A interrupt priority as 0
IntEnable(INT_WTIMER1A); // Enable Wide Timer 1A interrupt
// Configure WTimer1B
timerLoadValue = SysCtlClockGet() / 10 - 1; // Set to interrupt every 100ms
TimerLoadSet(WTIMER1_BASE, TIMER_B, timerLoadValue);
TimerIntRegister(WTIMER1_BASE, TIMER_B, TimeoutHandler); // Register interrupt handler
TimerIntEnable(WTIMER1_BASE, TIMER_TIMB_TIMEOUT); // Enable timer timeout interrupt
IntPrioritySet(INT_WTIMER1B, 0); // Configure Wide Timer 1B interrupt priority as 0
IntEnable(INT_WTIMER1B); // Enable Wide Timer 1B interrupt
TimerEnable(WTIMER1_BASE, TIMER_BOTH); // Enable both timers
validRXData = false;
}
void setup_pwm()
{
SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOB);
GPIOPinConfigure(GPIO_PB6_T0CCP0);
GPIOPinTypeTimer(GPIO_PORTB_BASE, GPIO_PIN_6);
SysCtlPeripheralEnable(SYSCTL_PERIPH_TIMER0);
}
// *************** GPIO_Init ***************
void GPIO_Init( GPIO_PORT_T port, GPIO_PIN_T pins, unsigned long dir_mode,
unsigned long strength, unsigned long pin_type )
{
if( 0 == GPIO_PortStatusFlag[port] )
{
SysCtlPeripheralEnable( GPIO_Peripheral[port] );
GPIO_PortStatusFlag[port] = 1;
}
switch ( pin_type )
{
case CCP:
{
GPIOPinTypeTimer ( GPIO_PortBase[port], pins );
break;
}
case PWM:
{
break;
}
default:
{
// regular GPIOs
GPIOPadConfigSet( GPIO_PortBase[port], pins, strength, pin_type );
GPIODirModeSet( GPIO_PortBase[port], pins, dir_mode );
break;
}
}
}
/*********************************************************************************************************
** Function name: ConfigureFanPWM
** Descriptions:
** input parameters:
**
** Output parameters:: нч
** Returned value:
**
** Created by: zhangwen
** Created Date:
**--------------------------------------------------------------------------------------------------------
** Modified by:
** Modified date:
**--------------------------------------------------------------------------------------------------------
*********************************************************************************************************/
void ConfigureFanPWM(u8 u8DefaulPwm)
{
//
// The Timer1 peripheral must be enabled for use.
//
SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOD);
SysCtlPeripheralEnable(SYSCTL_PERIPH_WTIMER2);
//
// Configure the GPIO pin muxing for the Timer/CCP function.
// This is only necessary if your part supports GPIO pin function muxing.
// Study the data sheet to see which functions are allocated per pin.
// TODO: change this to select the port/pin you are using
//
GPIOPinConfigure(GPIO_PD1_WT2CCP1);
//
//
// Configure the ccp settings for CCP pin. This function also gives
// control of these pins to the SSI hardware. Consult the data sheet to
// see which functions are allocated per pin.
// TODO: change this to select the port/pin you are using.
//
GPIOPinTypeTimer(GPIO_PORTD_BASE, GPIO_PIN_1);
//
// Configure Timer1B as a 16-bit periodic timer.
//
TimerConfigure(WTIMER2_BASE, TIMER_CFG_SPLIT_PAIR | TIMER_CFG_B_PWM);
//
// Set the Timer1B load value to 50000. For this example a 66% duty cycle
// PWM signal will be generated. From the load value (i.e. 50000) down to
// match value (set below) the signal will be high. From the match value
// to 0 the timer will be low.
//
TimerLoadSet(WTIMER2_BASE, TIMER_B, 50000);
//
// Set the Timer1B match value to load value / 3.
//
TimerMatchSet(WTIMER2_BASE, TIMER_B,
TimerLoadGet(WTIMER2_BASE, TIMER_B) *u8DefaulPwm/100);
//
// Enable Timer1B.
//
TimerEnable(WTIMER2_BASE, TIMER_B);
//
// Loop forever while the Timer1B PWM runs.
}
void control_init() {
//// laser control
// Setup Timer0 for a 488.28125Hz "phase correct PWM" wave (assuming a 16Mhz clock)
// Timer0 can pwm either PD5 (OC0B) or PD6 (OC0A), we use PD6
// TCCR0A and TCCR0B are the registers to setup Timer0
// see chapter "8-bit Timer/Counter0 with PWM" in Atmga328 specs
// OCR0A sets the duty cycle 0-255 corresponding to 0-100%
// also see: http://arduino.cc/en/Tutorial/SecretsOfArduinoPWM
GPIOPinTypeGPIOOutput(LASER_EN_PORT, LASER_EN_MASK);
GPIOPinWrite(LASER_EN_PORT, LASER_EN_MASK, LASER_EN_INVERT);
// Configure timer
SysCtlPeripheralEnable(SYSCTL_PERIPH_TIMER0);
TimerConfigure(LASER_TIMER, TIMER_CFG_SPLIT_PAIR|TIMER_CFG_A_PWM|TIMER_CFG_B_ONE_SHOT);
TimerControlLevel(LASER_TIMER, TIMER_A, 1);
// PPI = PWMfreq/(feedrate/MM_PER_INCH/60)
// Set PPI Pulse timer
ppi_cycles = SysCtlClockGet() / 1000 * CONFIG_LASER_PPI_PULSE_MS;
ppi_divider = ppi_cycles >> 16;
ppi_cycles /= (ppi_divider + 1);
TimerPrescaleSet(LASER_TIMER, TIMER_B, ppi_divider);
TimerLoadSet(LASER_TIMER, TIMER_B, ppi_cycles);
// Setup ISR
TimerIntRegister(LASER_TIMER, TIMER_B, laser_isr);
TimerIntEnable(LASER_TIMER, TIMER_TIMB_TIMEOUT);
IntPrioritySet(INT_TIMER0B, CONFIG_LASER_PRIORITY);
// Set PWM refresh rate
laser_cycles = SysCtlClockGet() / CONFIG_LASER_PWM_FREQ; /*Hz*/
laser_divider = laser_cycles >> 16;
laser_cycles /= (laser_divider + 1);
// Setup Laser PWM Timer
TimerPrescaleSet(LASER_TIMER, TIMER_A, laser_divider);
TimerLoadSet(LASER_TIMER, TIMER_A, laser_cycles);
TimerPrescaleMatchSet(LASER_TIMER, TIMER_A, laser_divider);
laser_intensity = 0;
// Set default value
control_laser_intensity(0);
control_laser(0, 0);
TimerEnable(LASER_TIMER, TIMER_A);
// ToDo: Map the timer ccp pin sensibly
GPIOPinConfigure(GPIO_PB6_T0CCP0);
GPIOPinTypeTimer(LASER_PORT, (1 << LASER_BIT));
//// air and aux assist control
GPIOPinTypeGPIOOutput(ASSIST_PORT, ASSIST_MASK);
control_air_assist(false);
control_aux1_assist(false);
}
void initLCD() {
SysCtlPeripheralEnable(LCDPORTENABLE);
GPIOPinTypeGPIOOutput(LCDPORT,
0xff);
// Please refer to the HD44780 datasheet for how these initializations work!
SysCtlDelay((500e-3)*CLKSPEED/3);
GPIOPinWrite(LCDPORT, RS, 0x00 );
GPIOPinWrite(LCDPORT, D4 | D5 | D6 | D7, 0x30 );
GPIOPinWrite(LCDPORT, E, 0x02);SysCtlDelay((20e-6)*CLKSPEED/3); GPIOPinWrite(LCDPORT, E, 0x00);
SysCtlDelay((50e-3)*CLKSPEED/3);
GPIOPinWrite(LCDPORT, D4 | D5 | D6 | D7, 0x30 );
GPIOPinWrite(LCDPORT, E, 0x02);SysCtlDelay((20e-6)*CLKSPEED/3);GPIOPinWrite(LCDPORT, E, 0x00);
SysCtlDelay((50e-3)*CLKSPEED/3);
GPIOPinWrite(LCDPORT, D4 | D5 | D6 | D7, 0x30 );
GPIOPinWrite(LCDPORT, E, 0x02);SysCtlDelay((20e-6)*CLKSPEED/3); GPIOPinWrite(LCDPORT, E, 0x00);
SysCtlDelay((10e-3)*CLKSPEED/3);
GPIOPinWrite(LCDPORT, D4 | D5 | D6 | D7, 0x20 );
GPIOPinWrite(LCDPORT, E, 0x02);SysCtlDelay((20e-6)*CLKSPEED/3); GPIOPinWrite(LCDPORT, E, 0x00);
SysCtlDelay((10e-3)*CLKSPEED/3);
LCDCommand(0x01); // Clear the screen.
LCDCommand(0x06); // Cursor moves right.
LCDCommand(0x0f); // Cursor blinking, turn on LCD.
// Now change contrast, by using PWM output on GPIO pin V0 (required configuring timer)
// You could also use the pwm.h functions instead?
SysCtlPeripheralEnable(SYSCTL_PERIPH_TIMER3);
GPIOPinConfigure(GPIO_PB2_T3CCP0);
GPIOPinTypeTimer(GPIO_PORTB_BASE, GPIO_PIN_2);
//GPIOPinTypeGPIOOutput(GPIO_PORTB_BASE, GPIO_PIN_2);
//GPIOPinWrite(GPIO_PORTB_BASE, GPIO_PIN_2,0);
unsigned long ulPeriod = (SysCtlClockGet() / 50000)/2;
unsigned long dutyCycle1 = (unsigned long)(ulPeriod-1)*0.7;
TimerConfigure(TIMER3_BASE, (TIMER_CFG_SPLIT_PAIR|TIMER_CFG_A_PWM|TIMER_CFG_B_PWM));
TimerControlLevel(TIMER3_BASE, TIMER_BOTH, 0);
TimerLoadSet(TIMER3_BASE, TIMER_A, ulPeriod -1);
TimerMatchSet(TIMER3_BASE, TIMER_A, dutyCycle1);
TimerEnable(TIMER3_BASE, TIMER_A);
LCDCommand(0x0c);
}
extern "C" int main(void) {
unsigned long ir_period;
// 40 MHz system clock
SysCtlClockSet(SYSCTL_SYSDIV_5|SYSCTL_USE_PLL|
SYSCTL_XTAL_16MHZ|SYSCTL_OSC_MAIN);
ConfigureUART();
SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOF);
SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOA);
//
// Unlock PF0 so we can change it to a GPIO input
// Once we have enabled (unlocked) the commit register then re-lock it
// to prevent further changes. PF0 is muxed with NMI thus a special case.
//
HWREG(GPIO_PORTF_BASE + GPIO_O_LOCK) = GPIO_LOCK_KEY;
HWREG(GPIO_PORTF_BASE + GPIO_O_CR) |= 0x01;
HWREG(GPIO_PORTF_BASE + GPIO_O_LOCK) = 0;
// Interrupt on sw1
GPIODirModeSet(IR_PORT, IR_PIN, GPIO_DIR_MODE_IN);
GPIOPadConfigSet(IR_PORT, IR_PIN, GPIO_STRENGTH_2MA, GPIO_PIN_TYPE_STD);
GPIOPinTypeGPIOInput(IR_PORT, IR_PIN);
GPIOIntTypeSet(IR_PORT, IR_PIN, GPIO_FALLING_EDGE);
GPIOIntRegister(IR_PORT, ir_input_isr);
GPIOIntEnable(IR_PORT, IR_PIN );
IntMasterEnable();
GPIOPinTypeGPIOOutput(GPIO_PORTF_BASE, GPIO_PIN_1);
GPIOPinWrite(GPIO_PORTF_BASE, GPIO_PIN_1, 0);
GPIOPinConfigure(GPIO_PF1_T0CCP1);
GPIOPinTypeTimer(GPIO_PORTF_BASE, GPIO_PIN_1);
// Configure timer
ir_period = SysCtlClockGet() / (IR_CARRIER / 2);
UARTprintf("ir_period:%d\n", ir_period);
SysCtlPeripheralEnable(SYSCTL_PERIPH_TIMER0);
TimerConfigure(TIMER0_BASE, TIMER_CFG_SPLIT_PAIR|TIMER_CFG_B_PWM);
TimerLoadSet(TIMER0_BASE, TIMER_B, ir_period);
TimerMatchSet(TIMER0_BASE, TIMER_B, ir_period / 2); // PWM
TimerEnable(TIMER0_BASE, TIMER_B);
unsigned long m = 0;
while(1) {
TimerMatchSet(TIMER0_BASE, TIMER_B, m++); // PWM
if (m > ir_period) m = 0;
int i = 0;
while (i++ < 5000)
if (!ir.empty())
UARTprintf("%u", ir.pop_front());
}
}
void Config_PWM(void)
{
SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOB);
#ifdef PB2_T3CCP0
// Configure timer
SysCtlPeripheralEnable(SYSCTL_PERIPH_TIMER3);
GPIOPinConfigure(GPIO_PB2_T3CCP0);
TimerConfigure(TIMER3_BASE, TIMER_CFG_SPLIT_PAIR | TIMER_CFG_A_PWM);
TimerLoadSet(TIMER3_BASE, TIMER_A, DEFAULT_FREQ);
TimerMatchSet(TIMER3_BASE, TIMER_A, DEFAULT_FREQ); // PWM
TimerControlLevel(TIMER3_BASE, TIMER_A, false);
TimerEnable(TIMER3_BASE, TIMER_A);
#endif
SysCtlPeripheralEnable(SYSCTL_PERIPH_TIMER0);
GPIOPinConfigure(GPIO_PB6_T0CCP0); //Right
GPIOPinTypeTimer(GPIO_PORTB_BASE, GPIO_PIN_6);
TimerConfigure(TIMER0_BASE, TIMER_CFG_SPLIT_PAIR | TIMER_CFG_A_PWM);
TimerLoadSet(TIMER0_BASE, TIMER_A, DEFAULT_FREQ);
TimerMatchSet(TIMER0_BASE, TIMER_A, DEFAULT_FREQ); // PWM
TimerControlLevel(TIMER0_BASE, TIMER_A, false);
TimerEnable(TIMER0_BASE, TIMER_A);
#ifdef PB4_T1CCP0
SysCtlPeripheralEnable(SYSCTL_PERIPH_TIMER1);
GPIOPinConfigure(GPIO_PB4_T1CCP0);
GPIOPinTypeTimer(GPIO_PORTB_BASE, GPIO_PIN_4);
TimerConfigure(TIMER1_BASE, TIMER_CFG_SPLIT_PAIR | TIMER_CFG_A_PWM);
TimerLoadSet(TIMER1_BASE, TIMER_A, DEFAULT_FREQ);
TimerMatchSet(TIMER1_BASE, TIMER_A, DEFAULT_FREQ); // PWM
TimerControlLevel(TIMER1_BASE, TIMER_A, false);
TimerEnable(TIMER1_BASE, TIMER_A);
#endif
SetPWM(PWM_LEFT,DEFAULT_FREQ, 0);
SetPWM(PWM_RIGHT,DEFAULT_FREQ, 0);
}
void Tach_Init(void) {
SysCtlPeripheralEnable(SYSCTL_PERIPH_TIMER0);
SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOB);
GPIOPinTypeTimer(GPIO_PORTB_BASE, GPIO_PIN_0);
/* Setup Timer0A Counter in edge-time-capture mode. */
TimerDisable(TIMER0_BASE, TIMER_A);
//TimerConfigure(TIMER0_BASE, TIMER_CFG_16_BIT_PAIR | TIMER_CFG_A_CAP_TIME | TIMER_CFG_B_PERIODIC);
TimerIntEnable(TIMER0_BASE, TIMER_CAPA_EVENT | TIMER_TIMA_TIMEOUT);
TimerControlEvent(TIMER0_BASE, TIMER_A, TIMER_EVENT_POS_EDGE);
TimerLoadSet(TIMER0_BASE, TIMER_A, 0xFFFF);
IntEnable(INT_TIMER0A); // Activate timer
TimerEnable(TIMER0_BASE, TIMER_A);
}
void init(){
// Init OLED
RIT128x96x4Init(1000000);
// Set the clock to 50 MHz
SysCtlClockSet(SYSCTL_SYSDIV_4 | SYSCTL_USE_PLL | SYSCTL_OSC_MAIN | SYSCTL_XTAL_8MHZ);
// Select
SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOF);
GPIOPinTypeGPIOInput(GPIO_PORTF_BASE, GPIO_PIN_1);
GPIOPadConfigSet(GPIO_PORTF_BASE, GPIO_PIN_1, GPIO_STRENGTH_2MA, GPIO_PIN_TYPE_STD_WPU);
// Navigation Switches
SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOE);
GPIOPinTypeGPIOInput(GPIO_PORTE_BASE, GPIO_PIN_0 | GPIO_PIN_1 | GPIO_PIN_2 | GPIO_PIN_3);
GPIOPadConfigSet(GPIO_PORTE_BASE, GPIO_PIN_0 | GPIO_PIN_1 | GPIO_PIN_2 | GPIO_PIN_3, GPIO_STRENGTH_2MA, GPIO_PIN_TYPE_STD_WPU);
// CAN Connection
SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOD);
SysCtlPeripheralEnable(SYSCTL_PERIPH_CAN0);
GPIOPinTypeCAN(GPIO_PORTD_BASE, GPIO_PIN_0 | GPIO_PIN_1);
CANInit(CAN0_BASE);
CANBitRateSet(CAN0_BASE, 8000000, 250000);
CANIntEnable(CAN0_BASE, CAN_INT_MASTER);
IntEnable(INT_CAN0);
CANEnable(CAN0_BASE);
// CAN Objects
transmit.ulMsgID= 0x200;
transmit.ulMsgIDMask= 0;
transmit.ulMsgLen= 2*sizeof(unsigned long);
// IR Receiver
SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOD);
GPIOPinTypeTimer(GPIO_PORTD_BASE, GPIO_PIN_4);
// Timer
SysCtlPeripheralEnable(SYSCTL_PERIPH_TIMER0);
TimerConfigure(TIMER0_BASE, TIMER_CFG_A_CAP_TIME);
TimerControlEvent(TIMER0_BASE, TIMER_A, TIMER_EVENT_NEG_EDGE);
TimerLoadSet(TIMER0_BASE, TIMER_A, TIME_WIDTH);
TimerIntEnable(TIMER0_BASE, TIMER_CAPA_EVENT | TIMER_TIMA_TIMEOUT);
TimerEnable(TIMER0_BASE, TIMER_A);
IntEnable(INT_TIMER0A);
}
/**************************************************************************//**
* @brief This function initializes the ALS. The sensor is powered up and the
* onboard ADC is configured.
*
*
* @return None
******************************************************************************/
void
alsInit(void)
{
//
// Set ALS power pin (output high)
//
GPIOPinTypeGPIOOutput(BSP_ALS_PWR_BASE, BSP_ALS_PWR);
GPIOPinWrite(BSP_ALS_PWR_BASE, BSP_ALS_PWR, BSP_ALS_PWR);
//
// Configure ALS output pin as hw controlled, no drive (same as for timer)
//
GPIOPinTypeTimer(BSP_ALS_OUT_BASE, BSP_ALS_OUT);
//
// Configure ADC, Internal reference, 512 decimation rate (12bit)
//
SOCADCSingleConfigure(SOCADC_12_BIT, SOCADC_REF_INTERNAL);
}
//*****************************************************************************
//
//! Enables the sound output.
//!
//! This function enables the sound output, preparing it to play music or sound
//! effects.
//!
//! \return None.
//
//*****************************************************************************
void
SoundEnable(void)
{
//
// Set the timer to produce 40 kHz, which is well beyond the limits of
// human hearing.
//
TimerLoadSet(TIMER2_BASE, TIMER_A, (g_ulSystemClock / 40000) - 1);
//
// Restore the output volume.
//
SoundVolumeSet(g_ucVolume);
//
// Enable the PWM output timer.
//
TimerEnable(TIMER2_BASE, TIMER_A);
//
// Configure the speaker GPIO pin as a timer PWM pin.
//
GPIOPinTypeTimer(GPIO_PORTC_BASE, GPIO_PIN_7);
}
int main (void)
{
// Set the clock
SysCtlClockSet(SYSCTL_SYSDIV_2_5 | SYSCTL_USE_PLL | SYSCTL_OSC_MAIN | SYSCTL_XTAL_16MHZ);
// Set output
SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOF);
GPIOPinTypeGPIOOutput(GPIO_PORTF_BASE,GPIO_PIN_1);
// Configure PF1 as T0CCP1
SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOB);
GPIOPinConfigure(GPIO_PB6_T0CCP0);
GPIOPinTypeTimer(GPIO_PORTB_BASE,GPIO_PIN_6);
// Configure Timer
SysCtlPeripheralEnable(SYSCTL_PERIPH_TIMER0);
TimerConfigure(TIMER0_BASE,TIMER_CFG_SPLIT_PAIR|TIMER_CFG_A_PWM);
TimerLoadSet(TIMER0_BASE,TIMER_A,SysCtlClockGet());
TimerMatchSet(TIMER0_BASE,TIMER_A,SysCtlClockGet()/2);
TimerControlLevel(TIMER0_BASE,TIMER_A,false);
TimerEnable(TIMER0_BASE,TIMER_A);
}
//*****************************************************************************
//
// This example application demonstrates the use of the timers to generate
// periodic interrupts.
//
//*****************************************************************************
int
main(void)
{
unsigned long ulPeriod, dutyCycle; // En ejemplo
//
// Enable lazy stacking for interrupt handlers. This allows floating-point
// instructions to be used within interrupt handlers, but at the expense of
// extra stack usage.
//
ROM_FPULazyStackingEnable();
//
// Set the clocking to run directly from the crystal.
//
// ROM_SysCtlClockSet(SYSCTL_SYSDIV_1 | SYSCTL_USE_OSC | SYSCTL_OSC_MAIN |
// SYSCTL_XTAL_16MHZ);
// Agregado Ejemplo
// 40 MHz system clock
SysCtlClockSet(SYSCTL_SYSDIV_5|SYSCTL_USE_PLL| SYSCTL_XTAL_16MHZ|SYSCTL_OSC_MAIN);
ulPeriod = 1000;
dutyCycle = 250;
// Turn off LEDs
SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOF);
GPIOPinTypeGPIOOutput(GPIO_PORTF_BASE, GPIO_PIN_1|GPIO_PIN_2|GPIO_PIN_3);
GPIOPinWrite(GPIO_PORTF_BASE, GPIO_PIN_1|GPIO_PIN_2|GPIO_PIN_3, 0);
// Configure PB6 as T0CCP0
SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOB);
GPIOPinConfigure(GPIO_PB6_T0CCP0);
GPIOPinTypeTimer(GPIO_PORTB_BASE, GPIO_PIN_6);
// Configure timer
SysCtlPeripheralEnable(SYSCTL_PERIPH_TIMER0);
TimerConfigure(TIMER0_BASE, TIMER_CFG_SPLIT_PAIR|TIMER_CFG_A_PWM);
TimerLoadSet(TIMER0_BASE, TIMER_A, ulPeriod -1);
TimerMatchSet(TIMER0_BASE, TIMER_A, dutyCycle); // PWM
TimerEnable(TIMER0_BASE, TIMER_A);
// Fin Agregado
//
// Initialize the UART and write status.
//
ConfigureUART();
UARTprintf("\033[2JTimers example\n");
UARTprintf("T1: 0 T2: 0");
//
// Enable the GPIO port that is used for the on-board LED.
//
// ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOF);
//
// Enable the GPIO pins for the LED (PF1 & PF2).
//
// ROM_GPIOPinTypeGPIOOutput(GPIO_PORTF_BASE, GPIO_PIN_2 | GPIO_PIN_1);
//
// Enable the peripherals used by this example.
//
// ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_TIMER0);
// ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_TIMER1);
//
// Enable processor interrupts.
//
// ROM_IntMasterEnable();
//
// Configure the two 32-bit periodic timers.
//
// ROM_TimerConfigure(TIMER0_BASE, TIMER_CFG_PERIODIC);
// ROM_TimerConfigure(TIMER1_BASE, TIMER_CFG_PERIODIC);
// ROM_TimerLoadSet(TIMER0_BASE, TIMER_A, ROM_SysCtlClockGet());
// ROM_TimerLoadSet(TIMER1_BASE, TIMER_A, ROM_SysCtlClockGet() / 2);
//
// Setup the interrupts for the timer timeouts.
//
// ROM_IntEnable(INT_TIMER0A);
// ROM_IntEnable(INT_TIMER1A);
// ROM_TimerIntEnable(TIMER0_BASE, TIMER_TIMA_TIMEOUT);
// ROM_TimerIntEnable(TIMER1_BASE, TIMER_TIMA_TIMEOUT);
//
// Enable the timers.
//
// ROM_TimerEnable(TIMER0_BASE, TIMER_A);
// ROM_TimerEnable(TIMER1_BASE, TIMER_A);
//
// Loop forever while the timers run.
//
while(1)
{
}
}
// After a certain number of edges are captured, the application prints out
// the results and compares the elapsed time between edges to the expected
// value.
//
// Note that the "B" timer is used because on some devices the "A" timer does
// not work correctly with the uDMA controller. Refer to the chip errata for
// details.
//
//*****************************************************************************
int
main(void)
{
unsigned long ulIdx;
unsigned short usTimerElapsed;
//unsigned short usTimerErr;
//
// Set the clocking to run directly from the crystal.
//
ROM_SysCtlClockSet(SYSCTL_SYSDIV_1 | SYSCTL_USE_OSC | SYSCTL_OSC_MAIN |
SYSCTL_XTAL_16MHZ);
//
// Initialize the UART and write a status message.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOA);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOB);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_UART0);
GPIOPinConfigure(GPIO_PA0_U0RX);
GPIOPinConfigure(GPIO_PA1_U0TX);
ROM_GPIOPinTypeUART(GPIO_PORTA_BASE, GPIO_PIN_0 | GPIO_PIN_1);
ROM_UARTConfigSetExpClk(UART0_BASE, ROM_SysCtlClockGet(), 115200,
(UART_CONFIG_WLEN_8 | UART_CONFIG_STOP_ONE |
UART_CONFIG_PAR_EVEN));
//UARTStdioInit(0);
//UARTprintf("\033[2JuDMA edge capture timer example\n\n");
//UARTprintf("This example requires that PD0 and PD7 be jumpered together"
// "\n\n");
//
// Create a signal source that can be used as an input for the CCP1 pin.
//
SetupSignalSource();
//
// Enable the GPIO port used for the CCP1 input.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOD);
//
// Configure the Timer0 CCP1 function to use PD7
//
GPIOPinConfigure(GPIO_PB2_CCP3);
GPIOPinTypeTimer(GPIO_PORTB_BASE, GPIO_PIN_2);
//
// Set up Timer0B for edge-timer mode, positive edge
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_TIMER1);
TimerConfigure(TIMER1_BASE, TIMER_CFG_16_BIT_PAIR | TIMER_CFG_B_CAP_TIME);
TimerControlEvent(TIMER1_BASE, TIMER_B, TIMER_EVENT_BOTH_EDGES);
TimerLoadSet(TIMER1_BASE, TIMER_B, 0xffff);
//
// Enable the uDMA peripheral
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_UDMA);
//
// Enable the uDMA controller error interrupt. This interrupt will occur
// if there is a bus error during a transfer.
//
ROM_IntEnable(INT_UDMAERR);
//
// Enable the uDMA controller.
//
ROM_uDMAEnable();
//
// Point at the control table to use for channel control structures.
//
ROM_uDMAControlBaseSet(ucControlTable);
//
// Put the attributes in a known state for the uDMA Timer0B channel. These
// should already be disabled by default.
//
ROM_uDMAChannelAttributeDisable(UDMA_CHANNEL_TMR1B,
UDMA_ATTR_ALTSELECT | UDMA_ATTR_USEBURST |
UDMA_ATTR_HIGH_PRIORITY |
UDMA_ATTR_REQMASK);
//
// Configure DMA channel for Timer0B to transfer 16-bit values, 1 at a
// time. The source is fixed and the destination increments by 16-bits
// (2 bytes) at a time.
//
ROM_uDMAChannelControlSet(UDMA_CHANNEL_TMR1B | UDMA_PRI_SELECT,
UDMA_SIZE_16 | UDMA_SRC_INC_NONE |
UDMA_DST_INC_16 | UDMA_ARB_1);
//
// Set up the transfer parameters for the Timer0B primary control
// structure. The mode is set to basic, the transfer source is the
// Timer0B register, and the destination is a memory buffer. The
// transfer size is set to a fixed number of capture events.
//
ROM_uDMAChannelTransferSet(UDMA_CHANNEL_TMR1B | UDMA_PRI_SELECT,
UDMA_MODE_BASIC,
(void *)(TIMER1_BASE + TIMER_O_TBR),
g_usTimerBuf, MAX_TIMER_EVENTS);
//
// Enable the timer capture event interrupt. Note that this signal is
// used to trigger the DMA request and not an actual interrupt.
// Start the capture timer running and enable its interrupt channel.
// The timer interrupt channel is used by the uDMA controller.
//
//UARTprintf("Starting timer and uDMA\n");
TimerIntEnable(TIMER1_BASE, TIMER_CAPB_EVENT);
TimerEnable(TIMER1_BASE, TIMER_B);
IntEnable(INT_TIMER1B);
//
// Now enable the DMA channel for Timer0B. It should now start performing
// transfers whenever there is a rising edge detected on the CCP1 pin.
//
ROM_uDMAChannelEnable(UDMA_CHANNEL_TMR1B);
//
// Enable processor interrupts.
//
ROM_IntMasterEnable();
//
// Wait for the transfer to complete.
//
//UARTprintf("Waiting for transfers to complete\n");
while(!g_bDoneFlag)
{
}
//
// Check for the expected number of occurrences of the interrupt handler,
// and that there are no DMA errors
//
if(g_uluDMAErrCount != 0)
{
//UARTprintf("\nuDMA errors were detected!!!\n\n");
}
if(g_ulTimer0BIntCount != 1)
{
//UARTprintf("\nUnexpected number of interrupts occurrred (%d)!!!\n\n",
// g_ulTimer0BIntCount);
}
//
// Display the timer values that were captured using the edge capture timer
// with uDMA. Compare the difference between stored values to the PWM
// period and make sure they match. This verifies that the edge capture
// DMA transfers were occurring with the correct timing.
//
//UARTprintf("\n Captured\n");
//UARTprintf("Event Value Difference Status\n");
//UARTprintf("----- -------- ---------- ------\n");
const unsigned char nbColonnes = '1';
UARTSend(&nbColonnes,1);
for(ulIdx = 1; ulIdx < MAX_TIMER_EVENTS; ulIdx++)
{
//
// Due to timer erratum, when the timer rolls past 0 as it counts
// down, it will trigger an additional DMA transfer even though there
// was not an edge capture. This will appear in the data buffer as
// a duplicate value - the value will be the same as the prior capture
// value. Therefore, in this example we skip past the duplicated
// value.
//
if(g_usTimerBuf[ulIdx] == g_usTimerBuf[ulIdx - 1])
{
const unsigned char dup = '$';
UARTSend(&dup,1);
//UARTprintf(" %2u 0x%04X skipped duplicate\n", ulIdx,
// g_usTimerBuf[ulIdx]);
continue;
}
//
// Compute the difference between adjacent captured values, and then
// compare that to the expected timeout period.
//
usTimerElapsed = g_usTimerBuf[ulIdx - 1] - g_usTimerBuf[ulIdx];
//usTimerErr = usTimerElapsed > TIMEOUT_VAL ?
// usTimerElapsed - TIMEOUT_VAL :
// TIMEOUT_VAL - usTimerElapsed;
//
// Print the captured value and the difference from the previous
//
unsigned char data[10];
itoa(usTimerElapsed,data);
UARTSend(data,10);
//UARTprintf(" %2u 0x%04X %8u ", ulIdx, g_usTimerBuf[ulIdx],
// usTimerElapsed);
//
// Print error status based on the deviation from expected difference
// between samples (calculated above). Allow for a difference of up
// to 1 cycle. Any more than that is considered an error.
//
//if(usTimerErr > 1)
//{
// UARTprintf(" ERROR\n");
//}
//else
//{
// UARTprintf(" OK\n");
//}
}
const unsigned char fin = '\n';
UARTSend(&fin,1);
//
// End of application
//
while(1)
{
}
}
int main(void) {
volatile unsigned long ulLoop;
//
// Enable lazy stacking for interrupt handlers. This allows floating-point
// instructions to be used within interrupt handlers, but at the expense of
// extra stack usage.
//
ROM_FPULazyStackingEnable();
//
// Set the clocking to run directly from the crystal.
//
ROM_SysCtlClockSet(
SYSCTL_SYSDIV_1 | SYSCTL_USE_OSC | SYSCTL_XTAL_16MHZ
| SYSCTL_OSC_MAIN);
//
// Enable the GPIO port that is used for the on-board LED.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOF);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_TIMER1 | SYSCTL_PERIPH_TIMER0);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOA);
//
// Enable the GPIO pins for the LED (PF2 & PF3).
//
//ROM_GPIOPinTypeGPIOOutput(GPIO_PORTF_BASE, GPIO_PIN_2 | GPIO_PIN_1 | GPIO_PIN_3);
ROM_IntMasterEnable();
//
// Initialize the UART.
//
ROM_GPIOPinConfigure (GPIO_PA0_U0RX);
ROM_GPIOPinConfigure (GPIO_PA1_U0TX);
ROM_GPIOPinTypeUART(GPIO_PORTA_BASE, GPIO_PIN_0 | GPIO_PIN_1);
UARTStdioInit(0);
UARTEchoSet(true);
//
// Enable the UART interrupt.
//
//
/// Initialize PWM
//
GPIOPinConfigure(GPIO_PF1_T0CCP1);
GPIOPinConfigure(GPIO_PF2_T1CCP0);
GPIOPinConfigure(GPIO_PF3_T1CCP1);
GPIOPinTypeTimer(GPIO_PORTF_BASE, GPIO_PIN_1 | GPIO_PIN_1 | GPIO_PIN_1);
//
// Configure Timer as a 16-bit periodic timer.
//
TimerConfigure(TIMER0_BASE, TIMER_CFG_16_BIT_PAIR |
TIMER_CFG_B_PWM);
TimerConfigure(TIMER1_BASE, TIMER_CFG_16_BIT_PAIR |
TIMER_CFG_A_PWM);
TimerConfigure(TIMER1_BASE, TIMER_CFG_16_BIT_PAIR |
TIMER_CFG_B_PWM);
// Configure period is 10 KHz
TimerLoadSet(TIMER0_BASE, TIMER_B, 16000);
TimerLoadSet(TIMER1_BASE, TIMER_A, 16000);
TimerLoadSet(TIMER1_BASE, TIMER_B, 16000);
//
// Set the Timer match value to load value (100% ON) .
//
TimerMatchSet(TIMER0_BASE, TIMER_B, PWM_CTR.CH1);
TimerMatchSet(TIMER1_BASE, TIMER_A, PWM_CTR.CH2);
TimerMatchSet(TIMER1_BASE, TIMER_B, PWM_CTR.CH3);
TimerEnable(TIMER0_BASE, TIMER_B);
TimerEnable(TIMER1_BASE, TIMER_BOTH);
// // Hello!
//
UARTprintf("LED PWM Control Demo\n");
//
// We are finished. Hang around doing nothing.
//
while (1) {
}
}
/**********************************************************************************************
* Main
*********************************************************************************************/
void main(void) {
//After tomorrow's test flight. FOR THE LOVE OF GOD MOVE THESE INITALIZATIONS TO FUNCTIONS
/**********************************************************************************************
* Local Variables
*********************************************************************************************/
unsigned long ultrasonic = 0;
// Enable lazy stacking for interrupt handlers. This allows floating-point
// instructions to be used within interrupt handlers, but at the expense of
// extra stack usage.
FPULazyStackingEnable();
//Set the clock speed to 80MHz aka max speed
SysCtlClockSet(SYSCTL_SYSDIV_2_5 | SYSCTL_USE_PLL | SYSCTL_OSC_MAIN | SYSCTL_XTAL_16MHZ);
/*unsigned long test[2];
test[0] = 180;
test[1] = 10;
short bob[1];
bob[0] = ((char)test[0]<<8)|(char)test[1];
float jimmy = (short)(((char)test[0]<<8)|(char)test[1]);
jimmy /= 26;*/
/**********************************************************************************************
* Peripheral Initialization Awake
*********************************************************************************************/
SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOF); //Turn on GPIO communication on F pins for switches
SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOE); //Turn on GPIO for ADC
SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOB); //Turn on GPIO for the PWM comms
SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOA); //Turn on GPIO for LED test
SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOD); //Turn on GPIO for UART
SysCtlPeripheralEnable(SYSCTL_PERIPH_TIMER0); //Turn on Timer for PWM
SysCtlPeripheralEnable(SYSCTL_PERIPH_TIMER1); //Turn on Timer for PWM
SysCtlPeripheralEnable(SYSCTL_PERIPH_TIMER2); //Turn on Timer for PWM
SysCtlPeripheralEnable(SYSCTL_PERIPH_TIMER3); //Turn on Timer for PWM
SysCtlPeripheralEnable(SYSCTL_PERIPH_I2C1); //Turn on I2C communication I2C slot 0
SysCtlPeripheralEnable(SYSCTL_PERIPH_UART2); //Turn on the UART com
SysCtlPeripheralEnable(SYSCTL_PERIPH_WDOG); //Turn on the watchdog timer. This is a risky idea but I think it's for the best.
/**********************************************************************************************
* Peripheral Initialization Sleep
*********************************************************************************************/
/*SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_GPIOF); //This sets what peripherals are still enabled in sleep mode while UART would be nice, it would require the clock operate at full speed which is :P
SysCtlPeripheralSleepDisable(SYSCTL_PERIPH_GPIOB);
SysCtlPeripheralSleepDisable(SYSCTL_PERIPH_GPIOA);
SysCtlPeripheralSleepDisable(SYSCTL_PERIPH_TIMER0);
SysCtlPeripheralSleepDisable(SYSCTL_PERIPH_TIMER1);
SysCtlPeripheralSleepDisable(SYSCTL_PERIPH_TIMER2);
SysCtlPeripheralSleepDisable(SYSCTL_PERIPH_TIMER3);
SysCtlPeripheralSleepDisable(SYSCTL_PERIPH_SSI0);
SysCtlPeripheralSleepDisable(SYSCTL_PERIPH_I2C1);
SysCtlPeripheralSleepDisable(SYSCTL_PERIPH_ADC);
SysCtlPeripheralClockGating(true); //I'm not sure about this one maybe remove it
*/
/**********************************************************************************************
* PWM Initialization
*********************************************************************************************/
SysCtlDelay((SysCtlClockGet() / (1000 * 3))*100); //This shouldn't be needed will test to remove
//PWM pin Setup
//PWM 0 on GPIO PB6, PWM 1 on pin 4... etc
GPIOPinConfigure(GPIO_PB6_T0CCP0); //Pitch - yaw +
GPIOPinConfigure(GPIO_PB4_T1CCP0); //Pitch + yaw +
GPIOPinConfigure(GPIO_PB0_T2CCP0); //Roll - yaw -
GPIOPinConfigure(GPIO_PB2_T3CCP0); //Roll + yaw -
GPIOPinTypeTimer(GPIO_PORTB_BASE, (GPIO_PIN_6|GPIO_PIN_4|GPIO_PIN_0|GPIO_PIN_2));
//Prescale the timers so they are slow enough to work with the ESC
TimerPrescaleSet(TIMER0_BASE,TIMER_A,2);
TimerPrescaleSet(TIMER1_BASE,TIMER_A,2);
TimerPrescaleSet(TIMER2_BASE,TIMER_A,2);
TimerPrescaleSet(TIMER3_BASE,TIMER_A,2);
//Basic LED Out Test Not sure why this is here look into This just turns on an LED that I don't have plugged in. should remove later
GPIOPinTypeGPIOOutput(GPIO_PORTA_BASE, GPIO_PIN_3);
GPIOPinWrite(GPIO_PORTA_BASE,GPIO_PIN_3,0xFF);
//GPIOPinTypeGPIOOutputOD(GPIO_PORTB_BASE,GPIO_PIN_0);
//Timers Setup for PWM and the load for the countdown
TimerConfigure(TIMER0_BASE, TIMER_CFG_SPLIT_PAIR|TIMER_CFG_A_PWM);
TimerLoadSet(TIMER0_BASE, TIMER_A, ulPeriod -1);
TimerConfigure(TIMER1_BASE, TIMER_CFG_SPLIT_PAIR|TIMER_CFG_A_PWM);
TimerLoadSet(TIMER1_BASE, TIMER_A, ulPeriod -1);
TimerConfigure(TIMER2_BASE, TIMER_CFG_SPLIT_PAIR|TIMER_CFG_A_PWM);
TimerLoadSet(TIMER2_BASE, TIMER_A, (ulPeriod -1));
TimerConfigure(TIMER3_BASE, TIMER_CFG_SPLIT_PAIR|TIMER_CFG_A_PWM);
TimerLoadSet(TIMER3_BASE, TIMER_A, ulPeriod -1);
//TimerPrescaleSet(TIMER2_BASE, TIMER_A, extender1);
//TimerLoadSet(TIMER2_BASE, TIMER_A, period1);
//Set the match which is when the thing will pull high
TimerMatchSet(TIMER0_BASE, TIMER_A, 254); //Duty cycle = (1-%desired)*1000 note this means this number is percent low not percent high
TimerMatchSet(TIMER1_BASE, TIMER_A, 254);
TimerMatchSet(TIMER2_BASE, TIMER_A, 254);
TimerMatchSet(TIMER3_BASE, TIMER_A, 254);
//TimerPrescaleMatchSet(TIMER2_BASE, TIMER_A, extender2);
//TimerMatchSet(TIMER2_BASE, TIMER_A, period2);
//Enable the timers
TimerEnable(TIMER0_BASE, TIMER_A);
TimerEnable(TIMER1_BASE, TIMER_A);
TimerEnable(TIMER2_BASE, TIMER_A);
TimerEnable(TIMER3_BASE, TIMER_A);
/**********************************************************************************************
* onboard Chip interrupt Initialization
*********************************************************************************************/
//These two buttons are used to reset the bluetooth module in case of disconnection
GPIOPinTypeGPIOOutput(GPIO_PORTF_BASE,GPIO_PIN_1|GPIO_PIN_2|GPIO_PIN_3); //RGB LED's
GPIOPinWrite(GPIO_PORTF_BASE,GPIO_PIN_1|GPIO_PIN_2|GPIO_PIN_3,0x00);
HWREG(GPIO_PORTF_BASE + GPIO_O_LOCK) = GPIO_LOCK_KEY_DD; //Sw1 (PF4) is unaviable unless you make it only a GPIOF input via these commands
HWREG(GPIO_PORTF_BASE + GPIO_O_CR) = 0x1;
GPIOPinTypeGPIOInput(GPIO_PORTF_BASE,GPIO_PIN_0|GPIO_PIN_4); //Onboard buttons (PF0=Sw2,PF4=Sw1
GPIOPadConfigSet(GPIO_PORTF_BASE, GPIO_PIN_0|GPIO_PIN_4, GPIO_STRENGTH_2MA,GPIO_PIN_TYPE_STD_WPU); //This will make the buttons falling edge (a press pulls them low)
//void (*functionPtr)(void) = &onBoardInteruptHandle;
GPIOPortIntRegister(GPIO_PORTF_BASE, onBoardInteruptHandle); //set function to handle interupt
GPIOIntTypeSet(GPIO_PORTF_BASE,GPIO_PIN_0|GPIO_PIN_4,GPIO_FALLING_EDGE); //Set the interrupt as falling edge
GPIOPinIntEnable(GPIO_PORTF_BASE,GPIO_PIN_0|GPIO_PIN_4); //Enable the interrupt
//IntMasterEnable();
IntEnable(INT_GPIOF);
/**********************************************************************************************
* UART Initialization
*********************************************************************************************/
//Unlock PD7
HWREG(GPIO_PORTD_BASE + GPIO_O_LOCK) = GPIO_LOCK_KEY_DD;
HWREG(GPIO_PORTD_BASE + GPIO_O_CR) = 0x80;
GPIOPinConfigure(GPIO_PD7_U2TX); //Set PD7 as TX
GPIOPinTypeUART(GPIO_PORTD_BASE, GPIO_PIN_7);
GPIOPinConfigure(GPIO_PD6_U2RX); //Set PD6 as RX
GPIOPinTypeUART(GPIO_PORTD_BASE, GPIO_PIN_6);
UARTConfigSetExpClk(UART2_BASE,SysCtlClockGet(),115200,UART_CONFIG_WLEN_8|UART_CONFIG_STOP_ONE|UART_CONFIG_PAR_NONE); //I believe the Xbee defaults to no parity I do know it's 9600 baud though, changed to 115200 for bluetooth reasons
UARTFIFOLevelSet(UART2_BASE,UART_FIFO_TX1_8,UART_FIFO_RX1_8); //Set's how big the fifo needs to be in order to call the interrupt handler, 2byte
UARTIntRegister(UART2_BASE,Uart2IntHandler); //Regiester the interrupt handler
UARTIntClear(UART2_BASE, UART_INT_TX | UART_INT_RX); //Clear the interrupt
UARTIntEnable(UART2_BASE, UART_INT_TX | UART_INT_RX); //Enable the interrupt to trigger on both TX and RX event's. Could possibly remove TX
UARTEnable(UART2_BASE); //Enable UART
IntEnable(INT_UART2); //Second way to enable handler not sure if needed using anyway
/**********************************************************************************************
* I2C Initialization
*********************************************************************************************/
//Serious credit to the man who made the Arduino version of this. he gave me addresses and equations. Sadly Arduino obfuscates what really is happening
//Link posted on blog page
//gyro address = 0x68 not 0x69
GPIOPinConfigure(GPIO_PA7_I2C1SDA);
GPIOPinTypeI2C(GPIO_PORTA_BASE, GPIO_PIN_7); //Set GPA7 as SDA
GPIOPinConfigure(GPIO_PA6_I2C1SCL);
GPIOPinTypeI2CSCL(GPIO_PORTA_BASE, GPIO_PIN_6); //Set GPA6 as SCL
I2CMasterInitExpClk(I2C1_MASTER_BASE,SysCtlClockGet(),false); //I think it operates at 100kbps
I2CMasterEnable(I2C1_MASTER_BASE);
//Initalize the accelerometer Address = 0x53
GPIOPinWrite(GPIO_PORTF_BASE,GPIO_PIN_1|GPIO_PIN_2|GPIO_PIN_3,0x02);
UARTSend(0xAB);
I2CTransmit(0x53,0x2D,0x00);
I2CTransmit(0x53,0x2D,0x10);
I2CTransmit(0x53,0x2D,0x08);
//Initalize the gyroscope Address = 0x68
I2CTransmit(0x68,0x3E,0x00);
I2CTransmit(0x68,0x15,0x07);
I2CTransmit(0x68,0x16,0x1E);
I2CTransmit(0x68,0x17,0x00);
UARTSend(0xAC);
/**********************************************************************************************
* SysTick Initialization
*********************************************************************************************/
SysTickIntRegister(SysTickIntHandler);
SysTickIntEnable();
SysTickPeriodSet((SysCtlClockGet() / (1000 * 3))*timeBetweenCalculations); //This sets the period for the delay. the last num is the num of milliseconds
SysTickEnable();
/**********************************************************************************************
* Watchdog Initialization
*********************************************************************************************/
WatchdogReloadSet(WATCHDOG_BASE, 0xFEEFEEFF); //Set the timer for a reset
WatchdogIntRegister(WATCHDOG_BASE,WatchdogIntHandler); //Enable interrupt
WatchdogIntClear(WATCHDOG_BASE);
WatchdogIntEnable(WATCHDOG_BASE);
WatchdogEnable(WATCHDOG_BASE); //Enable the actual timer
IntEnable(INT_WATCHDOG);
/**********************************************************************************************
* Preflight motor inialization maybe not necessary not going to test
*********************************************************************************************/
PWMSet(TIMER0_BASE,998);
PWMSet(TIMER1_BASE,998);
PWMSet(TIMER2_BASE,998);
PWMSet(TIMER3_BASE,998);
recievedCommands[0]=253;
SysCtlDelay((SysCtlClockGet() / (1000 * 3))*100); //Very important to ensure motor see's a start high (998 makes 0 sense but it works so shhhh don't tell anyone)
GPIOPinWrite(GPIO_PORTF_BASE,GPIO_PIN_1|GPIO_PIN_2|GPIO_PIN_3,0x06);
while(1){
WatchdogReloadSet(WATCHDOG_BASE, 0xFEEFEEFF); //Feed the dog a new time
//UARTSend(recievedCommands[0]);
//SysCtlDelay(50000);
//Set 4 PWM Outputs
//Get Acc data
I2CRead(0x53,0x32,6,quadAcc); //Address blah blah 2 for each axis
rawAccToG(quadAcc,RwAcc);
/*GPIOPinWrite(GPIO_PORTF_BASE,GPIO_PIN_1|GPIO_PIN_2|GPIO_PIN_3,0x04); //Blue
//Get Gyro data
/**************************************
Gyro ITG-3200 I2C
registers:
temp MSB = 1B, temp LSB = 1C
x axis MSB = 1D, x axis LSB = 1E
y axis MSB = 1F, y axis LSB = 20
z axis MSB = 21, z axis LSB = 22
*************************************/
I2CRead(0x68,0x1B,8,quadGyro); //Address blah blah 2 for each axis + 2 for temperature. why. because why not
rawGyroToDegsec(quadGyro,Gyro_ds);
//GPIOPinWrite(GPIO_PORTF_BASE,GPIO_PIN_1|GPIO_PIN_2|GPIO_PIN_3,0x02); //Red
//Get the actual angles in XYZ. Store them in RwEst
//getInclination(RwAcc, RwEst, RwGyro, Gyro_ds, Awz);
//After this function is called RwEst will hold the roll pitch and yaw
//RwEst will be returned in PITCH, ROLL, YAW 0, 1, 2 remember this order very important. Little obvious but yaw is worthless
/*if(RwEst[1]>0.5){
GPIOPinWrite(GPIO_PORTF_BASE,GPIO_PIN_1|GPIO_PIN_2|GPIO_PIN_3,0x06); //Red Blue, Correct data read in
}else{
GPIOPinWrite(GPIO_PORTF_BASE,GPIO_PIN_1|GPIO_PIN_2|GPIO_PIN_3,0x0A); //Red Green, The correct data is not there
}*/
/*GPIOPinWrite(GPIO_PORTF_BASE,GPIO_PIN_1|GPIO_PIN_2|GPIO_PIN_3,0x06); //Red Blue, Correct data read in
float test=RwAcc[0]*100; //These two commands work
char temp = (char)test;
//UARTSend((char)(RwAcc[0])*100); //This one does not
UARTSend(temp);
//UARTSend((char)(RwAcc[1])*100);
UARTSend(0xAA);
SysCtlDelay((SysCtlClockGet() / (1000 * 3))*1);
*/
}
}
/*---------------------------------------------------------------------------*/
PROCESS_THREAD(hello_world_process, ev, data)
{
static struct etimer timer;
static int count;
PROCESS_BEGIN();
/* i2c_init(I2C_SCL_PORT, I2C_SCL_PIN, I2C_SDA_PORT, I2C_SDA_PIN,
I2C_SCL_NORMAL_BUS_SPEED);*/
etimer_set(&timer, CLOCK_CONF_SECOND * 1);
count = 0;
relay_enable(PORT_D,LED_RELAY_PIN);
while(1) {
PROCESS_WAIT_EVENT();
if(ev == PROCESS_EVENT_TIMER) {
if(count %2 == 0){
//relay_on(PORT_D,LED_RELAY_PIN);
int delayIndex;
unsigned int pwmDutyCycle = 0x0000;
//
// Initialize the interrupt counter.
//
int g_ui32Counter = 0;
//
// Set the clocking to run directly from the external crystal/oscillator.
// (no ext 32k osc, no internal osc)
//
SysCtrlClockSet(false, false, 32000000);
//
// Set IO clock to the same as system clock
//
SysCtrlIOClockSet(32000000);
//
// The Timer0 peripheral must be enabled for use.
//
SysCtrlPeripheralEnable(SYS_CTRL_PERIPH_GPT0);
//
// Set up the serial console to use for displaying messages. This is
// just for this example program and is not needed for Timer operation.
//
//InitConsole();
//
// Display the example setup on the console.
//
UARTprintf("16-Bit Timer PWM ->");
UARTprintf("\n Timer = Timer0B");
UARTprintf("\n Mode = PWM with variable duty cycle");
//
// Configure GPTimer0A as a 16-bit PWM Timer.
//
TimerConfigure(GPTIMER0_BASE, GPTIMER_CFG_SPLIT_PAIR |
GPTIMER_CFG_A_PWM | GPTIMER_CFG_B_PWM);
//
// Set the GPTimer0B load value to 1sec by setting the timer load value
// to SYSCLOCK / 255. This is determined by:
// Prescaled clock = 16Mhz / 255
// Cycles to wait = 1sec * Prescaled clock
TimerLoadSet(GPTIMER0_BASE, GPTIMER_A, SysCtrlClockGet() / 4000);
TimerControlLevel(GPTIMER0_BASE, GPTIMER_A, false);
// Configure GPIOPortA.0 as the Timer0_InputCapturePin.1
IOCPinConfigPeriphOutput(GPIO_A_BASE, GPIO_PIN_0, IOC_MUX_OUT_SEL_GPT0_ICP1);
// Tell timer to use GPIOPortA.0
// Does Direction Selection and PAD Selection
GPIOPinTypeTimer(GPIO_A_BASE, GPIO_PIN_0);
//
// Enable processor interrupts.
//
IntMasterEnable();
//
// Enable GPTimer0B.
//
TimerEnable(GPTIMER0_BASE, GPTIMER_A);
UARTprintf("\n");
//
// Loop forever while the Timer0B runs.
//
while(1)
{
for (delayIndex = 0; delayIndex < 100000; delayIndex++);
pwmDutyCycle += 0x0F;
pwmDutyCycle &= 0xFFFF;
TimerMatchSet(GPTIMER0_BASE, GPTIMER_A, pwmDutyCycle);
UARTprintf("PWM DC Value: %04X -- %04X -- %04X\r",
pwmDutyCycle,
TimerValueGet(GPTIMER0_BASE, GPTIMER_A),
TimerMatchGet(GPTIMER0_BASE, GPTIMER_A) );
}
//SENSORS_ACTIVATE(cc2538_temp_sensor);
// printf( "%d is temp\n",cc2538_temp_sensor.value);
}
else {
//relay_off(PORT_D,LED_RELAY_PIN);
}
/* if(count %2 == 0)
{
relay_toggle(PORT_D,LED_RELAY_PIN);
relay_status(PORT_D,LED_RELAY_PIN);
}
*/
count ++;
etimer_reset(&timer);
}
}
PROCESS_END();
}
//*****************************************************************************
//
// Configure Timer1B as a 16-bit PWM with a duty cycle of 66%.
//
//*****************************************************************************
int
main(void)
{
//
// Set the clocking to run directly from the external crystal/oscillator.
// TODO: The SYSCTL_XTAL_ value must be changed to match the value of the
// crystal on your board.
//
SysCtlClockSet(SYSCTL_SYSDIV_1 | SYSCTL_USE_OSC | SYSCTL_OSC_MAIN |
SYSCTL_XTAL_16MHZ);
//
// The Timer1 peripheral must be enabled for use.
//
SysCtlPeripheralEnable(SYSCTL_PERIPH_TIMER1);
//
// For this example CCP3 is used with port E pin 4.
// The actual port and pins used may be different on your part, consult
// the data sheet for more information.
// GPIO port E needs to be enabled so these pins can be used.
// TODO: change this to whichever GPIO port you are using.
//
SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOE);
//
// Configure the GPIO pin muxing for the Timer/CCP function.
// This is only necessary if your part supports GPIO pin function muxing.
// Study the data sheet to see which functions are allocated per pin.
// TODO: change this to select the port/pin you are using
//
GPIOPinConfigure(GPIO_PE4_CCP3);
//
// Set up the serial console to use for displaying messages. This is
// just for this example program and is not needed for Timer/PWM operation.
//
InitConsole();
//
// Configure the ccp settings for CCP pin. This function also gives
// control of these pins to the SSI hardware. Consult the data sheet to
// see which functions are allocated per pin.
// TODO: change this to select the port/pin you are using.
//
GPIOPinTypeTimer(GPIO_PORTE_BASE, GPIO_PIN_4);
//
// Display the example setup on the console.
//
UARTprintf("16-Bit Timer PWM ->");
UARTprintf("\n Timer = Timer1B");
UARTprintf("\n Mode = PWM");
UARTprintf("\n Duty Cycle = 66%%\n");
UARTprintf("\nGenerating PWM on CCP3 (PE4) -> ");
//
// Configure Timer1B as a 16-bit periodic timer.
//
TimerConfigure(TIMER1_BASE, TIMER_CFG_16_BIT_PAIR |
TIMER_CFG_B_PWM);
//
// Set the Timer1B load value to 50000. For this example a 66% duty
// cycle PWM signal will be generated. From the load value (i.e. 50000)
// down to match value (set below) the signal will be high. From the
// match value to 0 the timer will be low.
//
TimerLoadSet(TIMER1_BASE, TIMER_B, 50000);
//
// Set the Timer1B match value to load value / 3.
//
TimerMatchSet(TIMER1_BASE, TIMER_B, TimerLoadGet(TIMER1_BASE, TIMER_B) / 3);
//
// Enable Timer1B.
//
TimerEnable(TIMER1_BASE, TIMER_B);
//
// Loop forever while the Timer1B PWM runs.
//
while(1)
{
//
// Print out indication on the console that the program is running.
//
PrintRunningDots();
}
}
int main(void) {
SysCtlClockSet(SYSCTL_SYSDIV_2_5 | SYSCTL_USE_PLL | SYSCTL_OSC_MAIN | SYSCTL_XTAL_16MHZ); //Configure System Clock
//SSD
SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOD); //Enable Port D
SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOB); //Enable Port B
GPIOPinTypeGPIOOutput(GPIO_PORTD_BASE,0x0F);
GPIOPinTypeGPIOOutput(GPIO_PORTB_BASE,0xFF);
//S1 and S2
SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOF); //Enable Port F
//Mode 1
SysCtlPeripheralEnable(SYSCTL_PERIPH_ADC0); //Enable ADC0 Module
SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOE); //Enable Port E
GPIOPinTypeADC(GPIO_PORTE_BASE, GPIO_PIN_1); //Select ADC Function of PE 1
ADCSequenceConfigure(ADC0_BASE, 2, ADC_TRIGGER_PROCESSOR, 0); //Configure ADC0 Sequencer
ADCSequenceStepConfigure(ADC0_BASE, 2, 0, ADC_CTL_CH2 | ADC_CTL_IE | ADC_CTL_END); //Configure the step of the sequencer
//Mode 2
SysCtlPeripheralEnable(SYSCTL_PERIPH_TIMER1); //Enable TIMER1 Module
GPIOPinTypeGPIOInput(GPIO_PORTF_BASE,GPIO_PIN_4); //Set PF4 as Input
GPIOPadConfigSet(GPIO_PORTF_BASE, GPIO_PIN_4, GPIO_STRENGTH_2MA,GPIO_PIN_TYPE_STD_WPU); //Configuring the PF4
GPIOIntTypeSet(GPIO_PORTF_BASE, GPIO_PIN_4, GPIO_BOTH_EDGES); //Setting Interrupt to trigger on both edges
TimerConfigure(TIMER1_BASE,TIMER_CFG_PERIODIC); //Configure TIMER1 into a Continuous Mode
TimerIntRegister(TIMER1_BASE, TIMER_A, fast); //Register interrupt if PF4 pressed for more than 1s
//Mode 3
SysCtlPeripheralEnable(SYSCTL_PERIPH_TIMER4); //Enable TIMER4 Module
SysCtlPeripheralEnable(SYSCTL_PERIPH_WTIMER0); //Enable WTIMER0 Module
SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOC); //Enable Port C
GPIOPinConfigure(GPIO_PC4_WT0CCP0);
GPIOPinTypeTimer(GPIO_PORTC_BASE,GPIO_PIN_4); //Set PC4 as a Timer Capture pin
TimerIntRegister(TIMER4_BASE,TIMER_A,freqfind); //Register a timer interrupt for TIMER4
TimerConfigure(TIMER4_BASE,TIMER_CFG_PERIODIC); //Configure Timer4 in continuous mode
TimerConfigure(WTIMER0_BASE,TIMER_CFG_SPLIT_PAIR|TIMER_CFG_A_CAP_COUNT);
TimerControlEvent(WTIMER0_BASE,TIMER_A,TIMER_EVENT_POS_EDGE); //Configure WTIMER0 for Positive Edge Capture
IntMasterEnable();
GPIOPinWrite(GPIO_PORTB_BASE,0xFF,0x00); //Initialize SSD to 0x00
GPIOPinWrite(GPIO_PORTD_BASE, 0x0F, 0x00); //Turn off all the digits of the SSD
SysCtlPeripheralEnable(SYSCTL_PERIPH_TIMER0); //Enable TIMER0 Module
TimerConfigure(TIMER0_BASE,TIMER_CFG_PERIODIC); //Configure TIMER0 into a Continuous Mode
TimerIntRegister(TIMER0_BASE, TIMER_A, ssdmux); //Register ISR for TIMER0 Interrupt to update SSD
TimerLoadSet(TIMER0_BASE, TIMER_A,SysCtlClockGet()/3000); //Set the refresh rate of the SSD
IntEnable(INT_TIMER0A);
TimerIntEnable(TIMER0_BASE,TIMER_TIMA_TIMEOUT); //Enable the timer interrupt
TimerEnable(TIMER0_BASE,TIMER_A); //Start the timer
HWREG(GPIO_PORTF_BASE|GPIO_O_LOCK) = GPIO_LOCK_KEY;
HWREG(GPIO_PORTF_BASE|GPIO_O_CR) = GPIO_PIN_0; //Unlock PF0 from the NMI mode
HWREG(GPIO_PORTF_BASE|GPIO_O_LOCK) = 0;
ssdset(0);
mode1set();
GPIOPinTypeGPIOInput(GPIO_PORTF_BASE, GPIO_PIN_0); //Setting PF0 to Input
GPIOPadConfigSet(GPIO_PORTF_BASE, GPIO_PIN_0, GPIO_STRENGTH_2MA,GPIO_PIN_TYPE_STD_WPU); //Configuring the pins
GPIOIntRegister(GPIO_PORTF_BASE, modeselect); //Register Interrupt for Port F with ISR modeselect()
GPIOIntClear(GPIO_PORTF_BASE, GPIO_PIN_0); //Clear any existing interrupts
GPIOIntTypeSet(GPIO_PORTF_BASE, GPIO_PIN_0, GPIO_FALLING_EDGE); //Setting Interrupt to trigger on falling edges
GPIOIntEnable(GPIO_PORTF_BASE, GPIO_PIN_0); //Enable the GPIO Interrupts on Port F
IntEnable(INT_GPIOF); //Enable Interrupts on Port F
while(1){
switch(mode) //Select operation according to mode
{
case 1: mode1();
break;
case 2: ssdsetHex(hex_count);
if(fast_flag)
{
mode2();
SysCtlDelay(SysCtlClockGet()/300);
}
break;
case 3: mode3(); break;
case 4: mode1(); break;
case 5: ssdsetHex(hex_count);
if(fast_flag)
{
mode2();
SysCtlDelay(SysCtlClockGet()/300);
} break;
}
SysCtlDelay(SysCtlClockGet()/3000);
}
return 0;
}
int main(void)
{
/* FIFO Buffer */
unsigned long temp[1];
/*Set the clocking to directly run from the crystal at 8MHz*/
SysCtlClockSet(SYSCTL_SYSDIV_4 | SYSCTL_USE_PLL | SYSCTL_OSC_MAIN | SYSCTL_XTAL_8MHZ);
/*Enable ADC Peripheral*/
SysCtlPeripheralEnable(SYSCTL_PERIPH_ADC0);
//Enable Timers.
SysCtlPeripheralEnable(SYSCTL_PERIPH_TIMER2);
SysCtlPeripheralEnable(SYSCTL_PERIPH_TIMER1);
SysCtlPeripheralEnable(SYSCTL_PERIPH_TIMER0);
/* Set the clock for the GPIO Port B */
SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOB);
/* Set the type of the GPIO Pin */
GPIOPinTypeTimer(GPIO_PORTB_BASE, GPIO_PIN_0|GPIO_PIN_1|GPIO_PIN_5);
/* UART configuration */
InitConsole();
//Setting the timer for PWM
TimerConfigure(TIMER2_BASE, TIMER_CFG_16_BIT_PAIR | TIMER_CFG_B_PWM);
TimerConfigure(TIMER1_BASE, TIMER_CFG_16_BIT_PAIR | TIMER_CFG_A_PWM);
TimerConfigure(TIMER0_BASE, TIMER_CFG_16_BIT_PAIR | TIMER_CFG_A_PWM);
/*Configure ADC Peripheral*/
ADCSequenceConfigure(ADC0_BASE, 3, ADC_TRIGGER_PROCESSOR, 0);
/*Configure ADC Sequence*/
ADCSequenceStepConfigure(ADC0_BASE, 3, 0, ADC_CTL_CH5 | ADC_CTL_IE | ADC_CTL_END);
/*Enable ADC sequence*/
ADCSequenceEnable(ADC0_BASE, 3);
/*Clear ADC Interrupt*/
ADCIntClear(ADC0_BASE, 3);
IntMasterEnable();
TimerLoadSet(TIMER2_BASE, TIMER_B, 500);
TimerLoadSet(TIMER1_BASE, TIMER_A, 500);
TimerLoadSet(TIMER0_BASE, TIMER_A, 500);
unsigned long i,k,counter=0,i1=0;
long num1,y=0,num2,num3,j=0,sum1=0,sum2=0,sum3=0;
while(1)
{
for(i=0;i<15648;i++)
{
if(i%24 == 0)
{
ADCProcessorTrigger(ADC0_BASE, 3);
while(!ADCIntStatus(ADC0_BASE, 3, false))
{
}
ADCIntClear(ADC0_BASE, 3);
ADCSequenceDataGet(ADC0_BASE, 3, temp);
x[i/24]=temp[0];
}
}
num1=0;
num2=0;
num3=0;
n1=_IQ17(0);
n2=_IQ17(0);
n3=_IQ17(0);
for(k=0;k<652;k++)
{
l1= _IQ17(b1[k]);
l2= _IQ17(b2[k]);
l3= _IQ17(b3[k]);
m= _IQ17(x[651-k]);
n1=n1 + _IQ17mpy(l1,m);
n2=n2 + _IQ17mpy(l2,m);
n3=n3 + _IQ17mpy(l3,m);
}
num1=_IQ17int(n1);
num2=_IQ17int(n2);
num3=_IQ17int(n3);
sum1+=num1*num1;
sum2+=num2*num2;
sum3+=num3*num3;
j++;
if(j==15)
{
sum1=sum1/500;
sum2=sum2/500;
sum3=sum3/500;
r1=isqrt(sum1);
r2=isqrt(sum2);
r3=isqrt(sum3);
sum1=sum2=0;
j=0;
}
r01=r1*r1*r1;
r02=r2*r2*r2;
r03=r3*r3*r3;
if(r01>0)
{
TimerConfigure(TIMER0_BASE, TIMER_CFG_16_BIT_PAIR | TIMER_CFG_A_PWM);
pwm1(256-r01);
}
else
{
TimerConfigure(TIMER0_BASE, TIMER_CFG_16_BIT_PAIR | TIMER_CFG_A_PERIODIC);
}
if(r02>0)
{
TimerConfigure(TIMER1_BASE, TIMER_CFG_16_BIT_PAIR | TIMER_CFG_A_PWM);
pwm2(256-r02);
}
else
{
TimerConfigure(TIMER1_BASE, TIMER_CFG_16_BIT_PAIR | TIMER_CFG_A_PERIODIC);
}
if(r03>0)
{
TimerConfigure(TIMER2_BASE, TIMER_CFG_16_BIT_PAIR | TIMER_CFG_B_PWM);
pwm3(256-r03);
}
else
{
TimerConfigure(TIMER2_BASE, TIMER_CFG_16_BIT_PAIR | TIMER_CFG_B_PERIODIC);
}
}
}
