void MEMSInit() {
I2CInit();
writeRegister(MPU6050_ADDRESS_AD0_LOW, MPU6050_RA_SMPLRT_DIV, MPU6050_SMPLRT_DIV);
writeRegister(MPU6050_ADDRESS_AD0_LOW, MPU6050_RA_GYRO_CONFIG, MPU6050_FS_SEL0);
writeRegister(MPU6050_ADDRESS_AD0_LOW, MPU6050_RA_ACCEL_CONFIG, MPU6050_AFS_SEL0);
writeRegister(MPU6050_ADDRESS_AD0_LOW, MPU6050_RA_INT_PIN_CFG, MPU6050_INT_LEVEL_LOW|MPU6050_LATCH_INT_ENABLE|MPU6050_INT_RD_SET);
writeRegister(MPU6050_ADDRESS_AD0_LOW, MPU6050_RA_INT_EN, MPU6050_DATA_RDY_EN);
writeRegister(MPU6050_ADDRESS_AD0_LOW, MPU6050_RA_PWR_MGMT_1, MPU6050_WAKE);
/*Interrupt triggers when touched to ground*/
//Therefore it is a idle high, interrupt triggers when pin is low
// use port0_5 as input event, interrupt test.
GPIOSetDir(PORT0, 21, INPUT );
NVIC_SetPriority(FLEX_INT0_IRQn, GPIOINT0PRIORITY);
// port2_1, single edge trigger, active high.
//channel #, port #, bit position, sense, event(polarity)
GPIOSetFlexInterrupt(CHANNEL0, PORT0, 21, 0, 0 );
}
/*****************************************************************************
** Function name: PMU_Init
**
** Descriptions: Initialize PMU and setup wakeup source.
** For Sleep and deepsleep, any of the I/O pins can be
** used as the wakeup source.
** For Deep Powerdown, only pin P1.4 can be used as
** wakeup source from deep powerdown.
**
** parameters: None
** Returned value: None
**
*****************************************************************************/
void PMU_Init( void )
{
#if Gint_Enable
uint32_t bitPattern[2];
uint32_t eventPattern[2];
#endif
/* Enable all clocks, even those turned off at power up. */
LPC_SYSCON->PDRUNCFG &= ~(WDT_OSC_PD | ADC_PD);
#if 0
/* FLEX_INT0 source */
GPIOSetFlexInterrupt( CHANNEL0, PORT1, 1, 0, 0 );
/* FLEX_INT0 as wakeup source */
LPC_SYSCON->STARTERP0 = 0x1<<0;
#endif
#if 0
/* FLEX_INT1 source */
GPIOSetFlexInterrupt( CHANNEL1, PORT1, 2, 0, 0 );
/* FLEX_INT1 as wakeup source */
LPC_SYSCON->STARTERP0 = 0x1<<1;
#endif
#if 0
/* FLEX_INT2 source */
GPIOSetFlexInterrupt( CHANNEL2, PORT1, 3, 0, 0 );
/* FLEX_INT2 as wakeup source */
LPC_SYSCON->STARTERP0 = 0x1<<2;
#endif
#if 0
/* FLEX_INT3 source */
GPIOSetFlexInterrupt( CHANNEL3, PORT1, 4, 0, 0 );
/* FLEX_INT3 as wakeup source */
LPC_SYSCON->STARTERP0 = 0x1<<3;
#endif
#if 0
/* FLEX_INT4 source */
GPIOSetFlexInterrupt( CHANNEL4, PORT0, 2, 0, 0 );
/* FLEX_INT4 as wakeup source */
LPC_SYSCON->STARTERP0 = 0x1<<4;
#endif
#if 0
/* FLEX_INT5 source */
GPIOSetFlexInterrupt( CHANNEL5, PORT0, 3, 0, 0 );
/* FLEX_INT5 as wakeup source */
LPC_SYSCON->STARTERP0 = 0x1<<5;
#endif
#if 0
/* FLEX_INT6 source */
GPIOSetFlexInterrupt( CHANNEL6, PORT0, 4, 0, 0 );
/* FLEX_INT6 as wakeup source */
LPC_SYSCON->STARTERP0 = 0x1<<6;
#endif
#if 1
/* FLEX_INT7 source */
/* PIO 0_17 set as wake-up pin */
GPIOSetFlexInterrupt( CHANNEL7, PORT0, 17, 0, 0 );
/* FLEX_INT7 as wakeup source */
LPC_SYSCON->STARTERP0 = 0x1<<7;
#endif
#if Gint_Enable
#if 0
bitPattern[0] = 0x00000020; /* PIO0_5 enabled */
bitPattern[1] = 0x00000004; /* PIO1_2 enabled */
eventPattern[0] = 0x00000020; /* PIO0_5 rising edge */
eventPattern[1] = 0x00000000; /* PIO1_2 falling edge */
/* GINT0_INT sources OR together */
GPIOSetGroupedInterrupt( GROUP0, &bitPattern[0], 0, 0, &eventPattern[0] );
/* GINT0_INT as wakeup source */
LPC_SYSCON->STARTERP1 = 0x1<<20;
#endif
#if 0
bitPattern[0] = 0x00000020; /* PIO0_5 enabled */
bitPattern[1] = 0x00000004; /* PIO1_2 enabled */
eventPattern[0] = 0x00000020; /* PIO0_5 rising edge */
eventPattern[1] = 0x00000000; /* PIO1_2 falling edge */
/* GINT0_INT sources AND together */
GPIOSetGroupedInterrupt( GROUP0, &bitPattern[0], 1, 0, &eventPattern[0] );
/* GINT0_INT as wakeup source */
LPC_SYSCON->STARTERP1 = 0x1<<20;
#endif
#if 0
bitPattern[0] = 0x00000020; /* PIO0_5 enabled */
bitPattern[1] = 0x00000004; /* PIO1_2 enabled */
eventPattern[0] = 0x00000000; /* PIO0_5 falling edge */
eventPattern[1] = 0x00000004; /* PIO1_2 rising edge */
/* GINT0_INT sources OR together */
GPIOSetGroupedInterrupt( GROUP1, &bitPattern[0], 0, 0, &eventPattern[0] );
/* GINT0_INT as wakeup source */
LPC_SYSCON->STARTERP1 = 0x1<<21;
#endif
#if 0
bitPattern[0] = 0x00000020; /* PIO0_5 enabled */
bitPattern[1] = 0x00000004; /* PIO1_2 enabled */
eventPattern[0] = 0x00000000; /* PIO0_5 falling edge */
eventPattern[1] = 0x00000004; /* PIO1_2 rising edge */
/* GINT0_INT sources OR together */
GPIOSetGroupedInterrupt( GROUP1, &bitPattern[0], 1, 0, &eventPattern[0] );
/* GINT0_INT as wakeup source */
LPC_SYSCON->STARTERP1 = 0x1<<21;
#endif
#endif
return;
}
