/**
* @brief Main program
* @param None
* @retval None
*/
int main()
{
/*System clock configuration*/
SystemInit();
// *(volatile uint32_t *)(0x41001014) = 0x0060100; //clock setting 48MHz
/* CLK OUT Set */
// PAD_AFConfig(PAD_PA,GPIO_Pin_2, PAD_AF2); // PAD Config - CLKOUT used 3nd Function
/* NVIC configuration */
NVIC_Configuration();
/* CPIO configuration */
GPIO_Setting();
/* Dualtimer 0_0 clock enable */
DUALTIMER_ClockEnable(DUALTIMER0_0);
/* Dualtimer 0_0 configuration */
Dualtimer_InitStructure.TimerLoad = 0x4FFFF;
Dualtimer_InitStructure.TimerControl_Mode = DUALTIMER_TimerControl_Periodic;
Dualtimer_InitStructure.TimerControl_OneShot = DUALTIMER_TimerControl_Wrapping;
Dualtimer_InitStructure.TimerControl_Pre = DUALTIMER_TimerControl_Pre_16;
Dualtimer_InitStructure.TimerControl_Size = DUALTIMER_TimerControl_Size_32;
DUALTIMER_Init(DUALTIMER0_0, &Dualtimer_InitStructure);
/* Dualtimer 0_0 Interrupt enable */
DUALTIMER_IntConfig(DUALTIMER0_0, ENABLE);
/* Dualtimer 0_0 start */
DUALTIMER_Start(DUALTIMER0_0);
while(1);
}
/**
* @brief Main program
* @param None
* @retval None
*/
int main()
{
/* External Clock */
CRG_PLL_InputFrequencySelect(CRG_OCLK);
/* Set Systme init */
SystemInit();
/* CPIO configuration */
GPIO_Setting();
/* Get System Clock */
sysclock = GetSystemClock();
/* SysTick_Config */
SysTick_Config((sysclock/1000));
while(1)
{
delay(1000);
/* RED LED toggled */
if(GPIO_ReadOutputDataBit(GPIOC,GPIO_Pin_0) != (uint32_t)Bit_RESET)
GPIO_ResetBits(GPIOC, GPIO_Pin_0);
else
GPIO_SetBits(GPIOC, GPIO_Pin_0);
}
}
/**
* @brief Main program
* @param None
* @retval None
*/
int main(void)
{
/*System clock configuration*/
SystemInit();
/* NVIC configuration */
NVIC_Configuration();
/* CPIO configuration */
GPIO_Setting();
/* Time base configuration */
PrescalerValue = (SystemCoreClock / 1000000) / 10; // Prescale is 2 for 10MHz
CaptureModeStruct.PWM_CHn_PR = PrescalerValue - 1;
CaptureModeStruct.PWM_CHn_MR = 600000;
CaptureModeStruct.PWM_CHn_LR = 1200000;
CaptureModeStruct.PWM_CHn_UDMR = PWM_CHn_UDMR_UpCount;
CaptureModeStruct.PWM_CHn_PDMR = PWM_CHn_PDMR_Periodic;
CaptureModeStruct.PWM_CHn_CMR = PWM_CHn_CMR_RisingEdge;
PWM_CaptureModeInit(PWM_CH0, &CaptureModeStruct);
/* PWM interrupt configuration :*/
PWM_IntConfig(PWM_CH0, ENABLE);
PWM_CHn_IntConfig(PWM_CH0, PWM_CHn_IER_CIE, ENABLE);
/* PWM channel 0 start */
PWM_CHn_Start(PWM_CH0);
while(1);
}
/**
* @brief Main program
* @param None
* @retval None
*/
int main(void)
{
/*System clock configuration*/
SystemInit();
// *(volatile uint32_t *)(0x41001014) = 0x0060100; //clock setting 48MHz
/* CLK OUT Set */
// PAD_AFConfig(PAD_PA,GPIO_Pin_2, PAD_AF2); // PAD Config - CLKOUT used 3nd Function
/* NVIC configuration */
NVIC_Configuration();
/* CPIO configuration */
GPIO_Setting();
/* Time base configuration */
CounterModeStruct.PWM_CHn_MR = 10;
CounterModeStruct.PWM_CHn_LR = 20;
CounterModeStruct.PWM_CHn_UDMR = PWM_CHn_UDMR_UpCount;
CounterModeStruct.PWM_CHn_PDMR = PWM_CHn_PDMR_Periodic;
CounterModeStruct.PWM_CHn_TCMR = PWM_CHn_TCMR_RisingCounterMode;
PWM_CounterModeInit(PWM_CH0, &CounterModeStruct);
/* PWM interrupt configuration */
PWM_IntConfig(PWM_CH0, ENABLE);
PWM_CHn_IntConfig(PWM_CH0, PWM_CHn_IER_MIE | PWM_CHn_IER_OIE, ENABLE);
/* PWM channel 0 start */
PWM_CHn_Start(PWM_CH0);
while(1);
}
/**
* @brief Main program
* @param None
* @retval None
*/
int main(void)
{
/*System clock configuration*/
SystemInit();
// *(volatile uint32_t *)(0x41001014) = 0x0060100; //clock setting 48MHz
/* CLK OUT Set */
// PAD_AFConfig(PAD_PA,GPIO_Pin_2, PAD_AF2); // PAD Config - CLKOUT used 3nd Function
/* NVIC configuration */
NVIC_Configuration();
/* CPIO configuration */
GPIO_Setting();
/* Timer mode configuration */
PrescalerValue = ((SystemFrequency / 1000000) / 10); // Prescale is 2 for 10MHz
TimerModeStructure.PWM_CHn_PR = PrescalerValue - 1;
TimerModeStructure.PWM_CHn_MR = 600000;
TimerModeStructure.PWM_CHn_LR = 1200000;
TimerModeStructure.PWM_CHn_UDMR = PWM_CHn_UDMR_UpCount;
TimerModeStructure.PWM_CHn_PDMR = PWM_CHn_PDMR_Periodic;
PWM_TimerModeInit(PWM_CH0, &TimerModeStructure);
/* PWM interrupt configuration */
PWM_IntConfig(PWM_CH0, ENABLE);
PWM_CHn_IntConfig(PWM_CH0, PWM_CHn_IER_MIE | PWM_CHn_IER_OIE, ENABLE);
/* PWM channel 0 start */
PWM_CHn_Start(PWM_CH0);
while(1);
}
/**
* @brief Main program
* @param None
* @retval None
*/
int main(void)
{
/*System clock configuration*/
SystemInit();
/* NVIC configuration */
NVIC_Configuration();
/* CPIO configuration */
GPIO_Setting();
/* Time base configuration */
CounterModeStruct.PWM_CHn_MR = 10;
CounterModeStruct.PWM_CHn_LR = 20;
CounterModeStruct.PWM_CHn_UDMR = PWM_CHn_UDMR_UpCount;
CounterModeStruct.PWM_CHn_PDMR = PWM_CHn_PDMR_Periodic;
CounterModeStruct.PWM_CHn_TCMR = PWM_CHn_TCMR_RisingCounterMode;
PWM_CounterModeInit(PWM_CH0, &CounterModeStruct);
/* PWM interrupt configuration */
PWM_IntConfig(PWM_CH0, ENABLE);
PWM_CHn_IntConfig(PWM_CH0, PWM_CHn_IER_MIE | PWM_CHn_IER_OIE, ENABLE);
/* PWM channel 0 start */
PWM_CHn_Start(PWM_CH0);
while(1);
}
/**
* @brief Main program
* @param None
* @retval None
*/
int main()
{
/*System clock configuration*/
SystemInit();
/* NVIC configuration */
NVIC_Configuration();
/* CPIO configuration */
GPIO_Setting();
/* Dualtimer 0_0 clock enable */
DUALTIMER_ClockEnable(DUALTIMER0_0);
/* Dualtimer 0_0 configuration */
Dualtimer_InitStructure.TimerLoad = 0x4FFFF;
Dualtimer_InitStructure.TimerControl_Mode = DUALTIMER_TimerControl_Periodic;
Dualtimer_InitStructure.TimerControl_OneShot = DUALTIMER_TimerControl_Wrapping;
Dualtimer_InitStructure.TimerControl_Pre = DUALTIMER_TimerControl_Pre_16;
Dualtimer_InitStructure.TimerControl_Size = DUALTIMER_TimerControl_Size_32;
DUALTIMER_Init(DUALTIMER0_0, &Dualtimer_InitStructure);
/* Dualtimer 0_0 Interrupt enable */
DUALTIMER_IntConfig(DUALTIMER0_0, ENABLE);
/* Dualtimer 0_0 start */
DUALTIMER_Start(DUALTIMER0_0);
while(1);
}
/**
* @brief Main program
* @param None
* @retval None
*/
int main(void)
{
/*System clock configuration*/
SystemInit();
/* CPIO configuration */
GPIO_Setting();
/* Timer mode configuration for PWM3*/
PrescalerValue = (SystemCoreClock / 1000000) / 10; // Prescale is 2 for 10MHz
TimerModeStructure.PWM_CHn_PR = PrescalerValue - 1;
TimerModeStructure.PWM_CHn_MR = 80000;
TimerModeStructure.PWM_CHn_LR = 100000; // 80% duty cycle
TimerModeStructure.PWM_CHn_UDMR = PWM_CHn_UDMR_UpCount;
TimerModeStructure.PWM_CHn_PDMR = PWM_CHn_PDMR_Periodic;
PWM_TimerModeInit(PWM_CH3, &TimerModeStructure);
/* Timer mode configuration for PWM4*/
TimerModeStructure.PWM_CHn_PR = PrescalerValue - 1;
TimerModeStructure.PWM_CHn_MR = 30000;
TimerModeStructure.PWM_CHn_LR = 100000; // 30% duty cycle
TimerModeStructure.PWM_CHn_UDMR = PWM_CHn_UDMR_UpCount;
TimerModeStructure.PWM_CHn_PDMR = PWM_CHn_PDMR_Periodic;
PWM_TimerModeInit(PWM_CH4, &TimerModeStructure);
/* Timer mode configuration for PWM5*/
TimerModeStructure.PWM_CHn_PR = PrescalerValue - 1;
TimerModeStructure.PWM_CHn_MR = 4294900000UL;
TimerModeStructure.PWM_CHn_LR = 4294800000UL;
TimerModeStructure.PWM_CHn_UDMR = PWM_CHn_UDMR_DownCount;
TimerModeStructure.PWM_CHn_PDMR = PWM_CHn_PDMR_Oneshot;
PWM_TimerModeInit(PWM_CH5, &TimerModeStructure);
/* PWM output enable */
PWM_CtrlPWMOutputEnable(PWM_CH3);
PWM_CtrlPWMOutputEnable(PWM_CH4);
PWM_CtrlPWMOutputEnable(PWM_CH5);
/* PWM start */
PWM_CHn_Start(PWM_CH3);
PWM_CHn_Start(PWM_CH4);
PWM_CHn_Start(PWM_CH5);
while(1);
}
/**
* @brief Main program
* @param None
* @retval None
*/
int main()
{
//uint8_t tx_size[8] = { 2, 2, 2, 2, 2, 2, 2, 2 };
//uint8_t rx_size[8] = { 2, 2, 2, 2, 2, 2, 2, 2 };
uint8_t mac_addr[6] = {0x00, 0x08, 0xDC, 0x71, 0x72, 0x77};
uint8_t src_addr[4] = {192, 168, 1, 98};
uint8_t gw_addr[4] = {192, 168, 1, 1};
uint8_t sub_addr[4] = {255, 255, 255, 0};
uint8_t tmp[8];
uint8_t i;
/* External Clock */
//CRG_PLL_InputFrequencySelect(CRG_OCLK);
/* Set Systme init */
SystemInit();
/* UART0 and UART1 configuration*/
//UART_StructInit(&UART_InitStructure);
/* Configure UART1 */
//UART_Init(UART1,&UART_InitStructure);
S_UART_Init(115200);
/* SysTick_Config */
SysTick_Config((GetSystemClock()/1000));
/* LED configuration */
GPIO_Setting();
/* Set WZ_100US Register */
setTIC100US((GetSystemClock()/10000));
//getTIC100US();
//printf(" GetSystemClock: %X, getTIC100US: %X, (%X) \r\n",
// GetSystemClock, getTIC100US(), *(uint32_t *)TIC100US);
#ifdef __DEF_USED_IC101AG__ //For using IC+101AG
*(volatile uint32_t *)(0x41003068) = 0x64; //TXD0 - set PAD strengh and pull-up
*(volatile uint32_t *)(0x4100306C) = 0x64; //TXD1 - set PAD strengh and pull-up
*(volatile uint32_t *)(0x41003070) = 0x64; //TXD2 - set PAD strengh and pull-up
*(volatile uint32_t *)(0x41003074) = 0x64; //TXD3 - set PAD strengh and pull-up
*(volatile uint32_t *)(0x41003050) = 0x64; //TXE - set PAD strengh and pull-up
#endif
#ifdef __W7500P__
*(volatile uint32_t *)(0x41003070) = 0x61;
*(volatile uint32_t *)(0x41003054) = 0x61;
#endif
#ifdef __DEF_USED_MDIO__
/* mdio Init */
mdio_init(GPIOB, MDC, MDIO );
/* PHY Link Check via gpio mdio */
while( link() == 0x0 )
{
printf(".");
delay(500);
}
printf("PHY is linked. \r\n");
#else
delay(1000);
#endif
/* Network Configuration (Default setting) */
setSHAR(mac_addr);
setSIPR(src_addr);
setGAR(gw_addr);
setSUBR(sub_addr);
getSHAR(tmp); printf("MAC ADDRESS : %.2X:%.2X:%.2X:%.2X:%.2X:%.2X\r\n",tmp[0],tmp[1],tmp[2],tmp[3],tmp[4],tmp[5]);
getSIPR(tmp); printf("IP ADDRESS : %.3d.%.3d.%.3d.%.3d\r\n",tmp[0],tmp[1],tmp[2],tmp[3]);
getGAR(tmp); printf("GW ADDRESS : %.3d.%.3d.%.3d.%.3d\r\n",tmp[0],tmp[1],tmp[2],tmp[3]);
getSUBR(tmp); printf("SN MASK: %.3d.%.3d.%.3d.%.3d\r\n",tmp[0],tmp[1],tmp[2],tmp[3]);
/* Set Network Configuration */
//wizchip_init(tx_size, rx_size);
/* HTTP Server Initialization */
httpServer_init(TX_BUF, RX_BUF, MAX_HTTPSOCK, socknumlist); // Tx/Rx buffers (1kB)
reg_httpServer_cbfunc(NVIC_SystemReset, NULL); // Callback: MCU Reset
{
/* Web content registration (web content in webpage.h, Example web pages) */
// Index page and netinfo / base64 image demo
reg_httpServer_webContent((uint8_t *)"index.html", (uint8_t *)index_page); // index.html : Main page example
reg_httpServer_webContent((uint8_t *)"netinfo.html", (uint8_t *)netinfo_page); // netinfo.html : Network information example page
reg_httpServer_webContent((uint8_t *)"netinfo.js", (uint8_t *)WIZwiki_W7500_web_netinfo_js); // netinfo.js : JavaScript for Read Network configuration (+ ajax.js)
//reg_httpServer_webContent((uint8_t *)"img.html", (uint8_t *)img_page); // img.html : Base64 Image data example page
// Example #1
reg_httpServer_webContent((uint8_t *)"dio.html", (uint8_t *)dio_page); // dio.html : Digital I/O control example page
reg_httpServer_webContent((uint8_t *)"dio.js", (uint8_t *)WIZwiki_W7500_web_dio_js); // dio.js : JavaScript for digital I/O control (+ ajax.js)
// Example #2
//reg_httpServer_webContent((uint8_t *)"ain.html", (uint8_t *)ain_page); // ain.html : Analog input monitor example page
//reg_httpServer_webContent((uint8_t *)"ain.js", (uint8_t *)WIZwiki_W7500_web_ain_js); // ain.js : JavaScript for Analog input monitor (+ ajax.js)
// Example #3
//reg_httpServer_webContent((uint8_t *)"ain_gauge.html", (uint8_t *)ain_gauge_page); // ain_gauge.html : Analog input monitor example page; using Google Gauge chart
//reg_httpServer_webContent((uint8_t *)"ain_gauge.js", (uint8_t *)ain_gauge_js); // ain_gauge.js : JavaScript for Google Gauge chart (+ ajax.js)
// AJAX JavaScript functions
reg_httpServer_webContent((uint8_t *)"ajax.js", (uint8_t *)WIZwiki_W7500_web_ajax_js); // ajax.js : JavaScript for AJAX request transfer
#ifdef _MAIN_DEBUG_
display_reg_webContent_list();
#endif
}
/* Main loop ***************************************/
while(1)
{
// TODO: insert user's code here
for(i = 0; i < MAX_HTTPSOCK; i++) httpServer_run(i); // HTTP Server handler
loopback_tcps(SOCK_TCPS, RX_BUF, 5000);
} // End of Main loop
}