/*
读取
*/
void EXTI9_5_IRQHandler( void )
{
uint8_t value1,value2,value3;
if( EXTI_GetITStatus( EXTI_Line5 ) != RESET )
{
IIC_RegRead( MMA845X_ADDR, INT_SOURCE_REG, &value1 );
IIC_RegRead( MMA845X_ADDR, PL_STATUS_REG, &value2 );
IIC_RegRead( MMA845X_ADDR, PULSE_SRC_REG, &value3 );
//rt_kprintf("\nINT=%02x %02x %02x\n",value1,value2,value3);
// trigger type grade
/*
Shake Trigger
*/
//----------- 碰撞判断--------------
if(value3>0)
{
ShakeSenor.Collision_Keeping=0; // clear
ShakeSenor.Layingdown_Keeping=0; // clear
if(firstrun==1)
firstrun=0; //上电 第一次触发不上报
else
{
Warn_Status[0]|=0x20; //bit29
PositionSD_Enable();
Current_UDP_sd=1;
rt_kprintf("\r\n 碰撞触发!\r\n");
}
}
//---------- 侧翻判断 --------------
if((value2>0)&&(value3==0))
{
ShakeSenor.LayingdownCounter++;
if(ShakeSenor.LayingdownCounter>100)
{
ShakeSenor.LayingdownCounter=0; // clear
if(firstrun==1)
firstrun=0; //上电 第一次触发不上报
else
{
if((Warn_Status[0]&0x40)==0x00)
{
PositionSD_Enable();
Current_UDP_sd=1;
rt_kprintf("\r\n 侧翻触发!\r\n");
}
Warn_Status[0]|=0x40; //bit29
ShakeSenor.Layingdown_Keeping=0;
}
}
}
// ---------------- Process ---------
EXTI_ClearITPendingBit( EXTI_Line5 );
}
else
shaker_continueCounter=0;
}
/*********************************************************\
* Initialize MMA865xQ
\*********************************************************/
void MMA865x_Init (void)
{
byte n;
/*
** Reset sensor, and wait for reboot to complete
*/
IIC_RegWrite(SlaveAddressIIC, CTRL_REG2, RST_MASK);
do {
n = IIC_RegRead(SlaveAddressIIC, CTRL_REG2);
} while (n & RST_MASK);
/*
** Configure sensor for:
** - Sleep Mode Poll Rate of 50Hz (20ms)
** - System Output Data Rate of 200Hz (5ms)
** - Full Scale of +/-8g
*/
IIC_RegWrite(SlaveAddressIIC, CTRL_REG1, ASLP_RATE_20MS + DATA_RATE_5MS);
/*
** Configure sensor data for:
** - Full Scale of +/-8g
**
** XYZ Data Event Flag Enable
*/
IIC_RegWrite(SlaveAddressIIC, XYZ_DATA_CFG_REG, FULL_SCALE_2G);
full_scale = FULL_SCALE_2G;
}
/*********************************************************\
* Put MMA865xQ into Active Mode
\*********************************************************/
void MMA865x_Active (void)
{
/*
** Set the Active bit in System Control 1 Register.
*/
IIC_RegWrite(SlaveAddressIIC, CTRL_REG1, (IIC_RegRead(SlaveAddressIIC, CTRL_REG1) | ACTIVE_MASK));
}
/*
读取
*/
void EXTI9_5_IRQHandler( void )
{
uint8_t value1, value2, value3;
if( EXTI_GetITStatus( EXTI_Line5 ) != RESET )
{
IIC_RegRead( MMA845X_ADDR, INT_SOURCE_REG, &value1 );
IIC_RegRead( MMA845X_ADDR, PL_STATUS_REG, &value2 );
IIC_RegRead( MMA845X_ADDR, PULSE_SRC_REG, &value3 );
//rt_kprintf("\nINT=%02x %02x %02x\n",value1,value2,value3);
// trigger type grade
/*
Shake Trigger
*/
//--------------Process -----------
if((Warn_Status[0] & 0x20) == 0x00) // 如果没报警那么就让他报警
{
shaker_continueCounter++;
if(shaker_continueCounter > 2600)
{
shaker_continueCounter = 0;
//----------------------------------------
if(firstrun == 1)
firstrun = 0; //上电 第一次触发不上报
else
{
Warn_Status[0] |= 0x20; //bit29
PositionSD_Enable(); // 使能发送
Current_UDP_sd = 1;
if(GB19056.workstate == 0)
rt_kprintf("\r\n 碰撞侧翻触发!\r\n");
}
//------------------------------------------
}
}
// ---------------- Process ---------
EXTI_ClearITPendingBit( EXTI_Line5 );
}
else
{
shaker_continueCounter = 0;
}
}
/*********************************************************\
* Put MMA865xQ into Standby Mode
\*********************************************************/
byte MMA865x_Standby (void)
{
byte n;
/*
** Read current value of System Control 1 Register.
** Put sensor into Standby Mode by clearing the Active bit.
** Return with previous value of System Control 1 Register.
*/
n = IIC_RegRead(SlaveAddressIIC, CTRL_REG1);
IIC_RegWrite(SlaveAddressIIC, CTRL_REG1, n & (~ACTIVE_MASK));
return (n & ACTIVE_MASK);
}
/*********************************************************\
* Put MPL3115A2 into Standby Mode
\*********************************************************/
byte MPL3115A2_Standby (void)
{
byte n;
/*
** Read current value of System Control 1 Register.
** Put sensor into Standby Mode.
** Return with previous value of System Control 1 Register.
*/
n = IIC_RegRead(SlaveAddressIIC, CTRL_REG1);
IIC_RegWrite(SlaveAddressIIC, CTRL_REG1, n & STANDBY_SBYB_0);
return(n);
}
/*********************************************************\
* Put MPL3115A2 into Active Mode
\*********************************************************/
void MPL3115A2_Active (void)
{
IIC_RegWrite(SlaveAddressIIC, CTRL_REG1, (IIC_RegRead(SlaveAddressIIC, CTRL_REG1) | ACTIVE_MASK));
}
