/**
* @brief Initialize and Configures the IO_Expanders Functionalities
* (Touch Screen ..) and configures all STM32100E-EVAL necessary
* hardware (GPIOs, APB clocks ..).
* @param None
* @retval IOE_OK if all initializations done correctly. Other value if error.
*/
uint8_t IOE_Config(void)
{
IOE_StructInit();
IOE_Init();
/* Read IO Expander 1 ID */
if(IOE_IsOperational(IOE_1_ADDR))
{
return IOE1_NOT_OPERATIONAL;
}
/* Generate IOExpander Software reset */
IOE_Reset(IOE_1_ADDR);
/* ---------------------- IO Expander configuration --------------------- */
/* Enable the GPIO, Touch Screen and ADC functionalities */
IOE_FnctCmd(IOE_1_ADDR, IOE_ADC_FCT | IOE_IO_FCT , ENABLE);
/* Touch Screen controller configuration */
IOE_TS_Config();
/* Temperature Sensor configuration */
IOE_TempSens_Config();
/* Configuration is OK */
return IOE_OK;
}
/**
* @brief Initializes and Configures the IO_Expander Touch Screen Functionality
* and configures all STM324x9I_EVAL necessary
* hardware (GPIOs, APB clocks ..).
* @param None
* @retval IOE_OK if all initializations done correctly. Other value if error.
*/
uint8_t IOE_Config(void)
{
/* Configure the needed pins */
IOE_GPIO_Config();
/* I2C initialization */
IOE_I2C_Config();
/* Read IO Expander ID */
if(IOE_IsOperational())
{
return IOE_NOT_OPERATIONAL;
}
/* Generate IO Expander Software reset */
IOE_Reset();
/* IO Expander configuration */
/* Touch Screen controller and ADC configuration */
IOE_FnctCmd(IOE_ADC_FCT, ENABLE);
IOE_TS_Config();
/* Configuration is OK */
return IOE_OK;
}
/**
* @brief Initializes and Configures the two IO_Expanders Functionalities
* (IOs, Touch Screen ..) and configures all STM3210C-EVAL necessary
* hardware (GPIOs, APB clocks ..).
* @param None
* @retval IOE_OK if all initializations done correctly. Other value if error.
*/
uint8_t IOE_Config(void)
{
/* Configure the needed pins */
IOE_GPIO_Config();
/* Configure the I2C peripheral */
IOE_I2C_Config();
/* Read IO Expander 1 ID */
if(IOE_IsOperational(IOE_1_ADDR))
{
return IOE1_NOT_OPERATIONAL;
}
if(IOE_IsOperational(IOE_2_ADDR))
{
return IOE2_NOT_OPERATIONAL;
}
/* Generate IOExpander Software reset */
IOE_Reset(IOE_1_ADDR);
IOE_Reset(IOE_2_ADDR);
/* ---------------------- IO Expander 1 configuration --------------------- */
/* Enable the GPIO, Touch Screen and ADC functionalities */
IOE_FnctCmd(IOE_1_ADDR, IOE_IO_FCT | IOE_TS_FCT | IOE_ADC_FCT, ENABLE);
/* Configure the VBAT pin in output mode pin*/
IOE_IOPinConfig(IOE_1_ADDR, VBAT_DIV_PIN , Direction_OUT);
/* ENABLE the alternate function for IN1 pin */
IOE_IOAFConfig(IOE_1_ADDR, VBAT_DIV_PIN, ENABLE);
/* Apply the default state for the out pins */
IOE_WriteIOPin(VBAT_DIV_PIN, BitReset);
/* Configure the MEMS interrupt pins in Input mode */
IOE_IOPinConfig(IOE_2_ADDR, (uint32_t)(MEMS_INT1_PIN | MEMS_INT2_PIN), Direction_IN);
/* ENABLE the alternate function for the Joystick pins */
IOE_IOAFConfig(IOE_2_ADDR, (uint32_t)(MEMS_INT1_PIN | MEMS_INT2_PIN), ENABLE);
/* Configure the IOs to detect Falling and Rising Edges */
IOE_IOEdgeConfig(IOE_2_ADDR, (uint32_t)(MEMS_INT1_PIN | MEMS_INT2_PIN), (uint32_t)(EDGE_FALLING | EDGE_RISING));
/* Touch Screen controller configuration */
IOE_TS_Config();
/* ------------------------------------------------------------------------ */
/* ---------------------- IO Expander 2 configuration --------------------- */
/* Enable the GPIO, Temperature Sensor and ADC functionalities */
IOE_FnctCmd(IOE_2_ADDR, IOE_IO_FCT | IOE_TEMPSENS_FCT | IOE_ADC_FCT, ENABLE);
/* Configure the Audio Codec Reset pin in output mode pin*/
IOE_IOPinConfig(IOE_2_ADDR, (uint32_t)(AUDIO_RESET_PIN), Direction_OUT);
IOE_IOPinConfig(IOE_2_ADDR, (uint32_t)(MII_INT_PIN), Direction_IN);
/* ENABLE the alternate function for IN1 pin */
IOE_IOAFConfig(IOE_2_ADDR, (uint32_t)(AUDIO_RESET_PIN | MII_INT_PIN), ENABLE);
/* Apply the default state for the out pins */
IOE_WriteIOPin(AUDIO_RESET_PIN, BitReset);
IOE_WriteIOPin(MII_INT_PIN, BitReset);
/* Configure the Joystick pins in Input mode */
IOE_IOPinConfig(IOE_2_ADDR, JOY_IO_PINS , Direction_IN);
/* ENABLE the alternate function for the Joystick pins */
IOE_IOAFConfig(IOE_2_ADDR, JOY_IO_PINS, ENABLE);
/* Configure the IOs to detect Falling and Rising Edges */
IOE_IOEdgeConfig(IOE_2_ADDR, JOY_IO_PINS, (uint8_t)(EDGE_FALLING | EDGE_RISING));
/* Temperature Sensor module configuration */
IOE_TempSens_Config();
/* ------------------------------------------------------------------------ */
/* Configuration is OK */
return IOE_OK;
}
