/*
* Update the location of the hardware cursor.
*/
static void Update_Cursor(void) {
/*
* The cursor location is a character offset from the beginning
* of page memory (I think).
*/
uint_t characterPos = (s_cons.row * NUMCOLS) + s_cons.col;
uchar_t origAddr;
/*
* Save original contents of CRT address register.
* It is considered good programming practice to restore
* it to its original value after modifying it.
*/
origAddr = In_Byte(CRT_ADDR_REG);
IO_Delay();
/* Set the high cursor location byte */
Out_Byte(CRT_ADDR_REG, CRT_CURSOR_LOC_HIGH_REG);
IO_Delay();
Out_Byte(CRT_DATA_REG, (characterPos >> 8) & 0xff);
IO_Delay();
/* Set the low cursor location byte */
Out_Byte(CRT_ADDR_REG, CRT_CURSOR_LOC_LOW_REG);
IO_Delay();
Out_Byte(CRT_DATA_REG, characterPos & 0xff);
IO_Delay();
/* Restore contents of the CRT address register */
Out_Byte(CRT_ADDR_REG, origAddr);
}
void NE2000_Handle_Ring_Buffer_Overflow(struct Net_Device *device) {
int txp, resend;
ulong_t baseAddr = device->baseAddr;
/* 1. Read and store the value of the TXP bit */
txp = In_Byte(baseAddr + NE2K_CR) & NE2K_CR_TXP;
/* 2. Issue the STOP command to the NIC */
Out_Byte(baseAddr + NE2K_CR, 0x21);
/* 3. Wait for at least 1.6 ms */
IO_Delay();
/* 4. Clear the NIC’s Remote Byte Count */
Out_Byte(baseAddr + NE2K0W_RBCR0, 0x00);
Out_Byte(baseAddr + NE2K0W_RBCR1, 0x00);
/* 5. Handle resend */
if (!txp) {
resend = 0;
} else {
int isr = In_Byte(baseAddr + NE2K0R_ISR);
if ((isr & NE2K_ISR_PTX) || (isr & NE2K_ISR_TXE)) {
resend = 0;
} else {
resend = 1;
}
}
/* 6. Place the NIC into loopback mode */
Out_Byte(baseAddr + NE2K0W_TCR, 0x02);
/* 7. Issue START command to the NIC */
Out_Byte(baseAddr + NE2K_CR, 0x22);
/* 8. Remove one or more packets from the receive buffer ring */
NE2000_Do_Receive(device);
/* 9. Reset the overwrite warning (OVW) bit in the ISR */
Out_Byte(baseAddr + NE2K0R_ISR, NE2K_ISR_OVW);
/* 10. Take the NIC out of loopback */
Out_Byte(baseAddr + NE2K0W_TCR, 0x00);
/* 11. Restart the interrupted transmit if resend = 1 */
if (resend) {
Out_Byte(baseAddr + NE2K_CR, 0x26);
}
}
/*
* Handler for keyboard interrupts.
*/
static void Keyboard_Interrupt_Handler(struct Interrupt_State* state)
{
uchar_t status, scanCode;
unsigned flag = 0;
bool release = false, shift;
Keycode keycode;
Begin_IRQ(state);
status = In_Byte(KB_CMD);
IO_Delay();
if ((status & KB_OUTPUT_FULL) != 0) {
/* There is a byte available */
scanCode = In_Byte(KB_DATA);
IO_Delay();
/*
* Print("code=%x%s\n", scanCode, (scanCode&0x80) ? " [release]" : "");
*/
if (scanCode & KB_KEY_RELEASE) {
release = true;
scanCode &= ~(KB_KEY_RELEASE);
}
if (scanCode >= SCAN_TABLE_SIZE) {
Print("Unknown scan code: %x\n", scanCode);
goto done;
}
/* Process the key */
shift = ((s_shiftState & SHIFT_MASK) != 0);
keycode = shift ? s_scanTableWithShift[scanCode] : s_scanTableNoShift[scanCode];
/* Update shift, control and alt state */
switch (keycode) {
case KEY_LSHIFT:
flag = LEFT_SHIFT;
break;
case KEY_RSHIFT:
flag = RIGHT_SHIFT;
break;
case KEY_LCTRL:
flag = LEFT_CTRL;
break;
case KEY_RCTRL:
flag = RIGHT_CTRL;
break;
case KEY_LALT:
flag = LEFT_ALT;
break;
case KEY_RALT:
flag = RIGHT_ALT;
break;
default:
goto noflagchange;
}
if (release)
s_shiftState &= ~(flag);
else
s_shiftState |= flag;
/*
* Shift, control and alt keys don't have to be
* queued, flags will be set!
*/
goto done;
noflagchange:
/* Format the new keycode */
if (shift)
keycode |= KEY_SHIFT_FLAG;
if ((s_shiftState & CTRL_MASK) != 0)
keycode |= KEY_CTRL_FLAG;
if ((s_shiftState & ALT_MASK) != 0)
keycode |= KEY_ALT_FLAG;
if (release)
keycode |= KEY_RELEASE_FLAG;
/* Put the keycode in the buffer */
Enqueue_Keycode(keycode);
/* Wake up event consumers */
Wake_Up(&s_waitQueue);
/*
* Pick a new thread upon return from interrupt
* (hopefully the one waiting for the keyboard event)
*/
g_needReschedule = true;
}
done:
End_IRQ(state);
}
