_mali_osk_errcode_t g3d_power_domain_control(int bpower_on)
{
if (bpower_on)
{
#if MALI_PMM_RUNTIME_JOB_CONTROL_ON
MALI_DEBUG_PRINT(3,("_mali_osk_pmm_dev_activate \n"));
_mali_osk_pm_dev_activate();
#else //MALI_PMM_RUNTIME_JOB_CONTROL_ON
void __iomem *status;
u32 timeout;
__raw_writel(S5P_INT_LOCAL_PWR_EN, S5P_PMU_G3D_CONF);
status = S5P_PMU_G3D_CONF + 0x4;
timeout = 10;
while ((__raw_readl(status) & S5P_INT_LOCAL_PWR_EN)
!= S5P_INT_LOCAL_PWR_EN) {
if (timeout == 0) {
MALI_PRINTF(("Power domain enable failed.\n"));
return -ETIMEDOUT;
}
timeout--;
_mali_osk_time_ubusydelay(100);
}
MALI_PRINTF(("MALI Power domain enabled"));
#endif //MALI_PMM_RUNTIME_JOB_CONTROL_ON
}
else
{
#if MALI_PMM_RUNTIME_JOB_CONTROL_ON
MALI_DEBUG_PRINT( 4,("_mali_osk_pmm_dev_idle\n"));
_mali_osk_pm_dev_idle();
#else //MALI_PMM_RUNTIME_JOB_CONTROL_ON
void __iomem *status;
u32 timeout;
__raw_writel(0, S5P_PMU_G3D_CONF);
status = S5P_PMU_G3D_CONF + 0x4;
/* Wait max 1ms */
timeout = 10;
while (__raw_readl(status) & S5P_INT_LOCAL_PWR_EN)
{
if (timeout == 0) {
MALI_PRINTF(("Power domain disable failed.\n" ));
return -ETIMEDOUT;
}
timeout--;
_mali_osk_time_ubusydelay( 100);
}
MALI_PRINTF(("MALI Power domain disabled"));
#endif //MALI_PMM_RUNTIME_JOB_CONTROL_ON
}
MALI_SUCCESS;
}
_mali_osk_errcode_t mali_platform_power_mode_change(struct device *dev, mali_power_mode power_mode)
{
switch (power_mode)
{
case MALI_POWER_MODE_ON:
MALI_DEBUG_PRINT(3, ("Mali platform: Got MALI_POWER_MODE_ON event, %s\n",
nPowermode ? "powering on" : "already on"));
if (nPowermode == MALI_POWER_MODE_LIGHT_SLEEP || nPowermode == MALI_POWER_MODE_DEEP_SLEEP) {
#if !defined(CONFIG_PM_RUNTIME)
g3d_power_domain_control(1);
#endif
MALI_DEBUG_PRINT(4, ("enable clock\n"));
enable_mali_clocks(dev);
if (nPowermode == MALI_POWER_MODE_DEEP_SLEEP) {
#ifdef CONFIG_MALI_DVFS
mali_devfreq = NULL;
if (!mali_devfreq_add(dev))
MALI_PRINTF(("failed to mali_devfreq_add()\n"));
#endif
}
#if defined(CONFIG_MALI400_PROFILING)
_mali_osk_profiling_add_event(MALI_PROFILING_EVENT_TYPE_SINGLE |
MALI_PROFILING_EVENT_CHANNEL_GPU |
MALI_PROFILING_EVENT_REASON_SINGLE_GPU_FREQ_VOLT_CHANGE,
mali_gpu_clk, mali_gpu_vol/1000, 0, 0, 0);
#endif
nPowermode = power_mode;
}
break;
case MALI_POWER_MODE_DEEP_SLEEP:
#ifdef CONFIG_MALI_DVFS
mali_devfreq_remove();
#endif
case MALI_POWER_MODE_LIGHT_SLEEP:
MALI_DEBUG_PRINT(3, ("Mali platform: Got %s event, %s\n", power_mode == MALI_POWER_MODE_LIGHT_SLEEP ?
"MALI_POWER_MODE_LIGHT_SLEEP" : "MALI_POWER_MODE_DEEP_SLEEP",
nPowermode ? "already off" : "powering off"));
if (nPowermode == MALI_POWER_MODE_ON) {
disable_mali_clocks();
#if defined(CONFIG_MALI400_PROFILING)
_mali_osk_profiling_add_event(MALI_PROFILING_EVENT_TYPE_SINGLE |
MALI_PROFILING_EVENT_CHANNEL_GPU |
MALI_PROFILING_EVENT_REASON_SINGLE_GPU_FREQ_VOLT_CHANGE,
0, 0, 0, 0, 0);
#endif
#if !defined(CONFIG_PM_RUNTIME)
g3d_power_domain_control(0);
#endif
nPowermode = power_mode;
}
break;
}
MALI_SUCCESS;
}
_mali_osk_errcode_t g3d_power_domain_control(int bpower_on)
{
MALI_SUCCESS;
if (bpower_on)
{
void __iomem *status;
u32 timeout;
__raw_writel(EXYNOS_INT_LOCAL_PWR_EN, S5P_G3D_CONFIGURATION);
status = S5P_G3D_STATUS;
timeout = 10;
while ((__raw_readl(status) & EXYNOS_INT_LOCAL_PWR_EN)
!= EXYNOS_INT_LOCAL_PWR_EN) {
if (timeout == 0) {
MALI_PRINTF(("Power domain enable failed.\n"));
return -ETIMEDOUT;
}
timeout--;
_mali_osk_time_ubusydelay(100);
}
}
else
{
void __iomem *status;
u32 timeout;
__raw_writel(0, S5P_G3D_CONFIGURATION);
status = S5P_G3D_STATUS;
/* Wait max 1ms */
timeout = 10;
while (__raw_readl(status) & EXYNOS_INT_LOCAL_PWR_EN)
{
if (timeout == 0) {
MALI_PRINTF(("Power domain disable failed.\n" ));
return -ETIMEDOUT;
}
timeout--;
_mali_osk_time_ubusydelay( 100);
}
}
MALI_SUCCESS;
}
void _mali_pm_callback(void *arg)
{
#if MALI_LICENSE_IS_GPL
if (mali_pm_wq)
{
queue_work(mali_pm_wq, &mali_pm_wq_work_handle);
}
else
{
MALI_PRINTF(("mali_pm_wq is NULL !!!\n"));
mali_bottom_half_pm(NULL);
}
#else
schedule_work(&mali_pm_wq_work_handle);
#endif
}
/* Can run in atomic context */
void _mali_osk_pm_dev_ref_dec(void)
{
#ifdef CONFIG_PM_RUNTIME
MALI_DEBUG_ASSERT_POINTER(mali_platform_device);
_mali_osk_atomic_dec(&mali_pm_ref_count);
#if (LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,37))
pm_runtime_mark_last_busy(&(mali_platform_device->dev));
pm_runtime_put_autosuspend(&(mali_platform_device->dev));
#else
pm_runtime_put(&(mali_platform_device->dev));
#endif
MALI_DEBUG_PRINT(4, ("Mali OSK PM: Power ref released (%u)\n", _mali_osk_atomic_read(&mali_pm_ref_count)));
#else /// CONFIG_PM_RUNTIME
if(_mali_osk_atomic_dec_return(&mali_pm_ref_count) == 0)
{
if (NULL != pm_timer)
{
_mali_osk_timer_mod(pm_timer, _mali_osk_time_mstoticks(mali_pm_wq ? 15 : 3000));
}
else
{
#if MALI_LICENSE_IS_GPL
if (mali_pm_wq)
{
queue_work(mali_pm_wq, &mali_pm_wq_work_handle);
}
else
{
MALI_PRINTF(("mali_pm_wq is NULL !!!\n"));
mali_bottom_half_pm(NULL);
}
#else
schedule_work(&mali_pm_wq_work_handle);
#endif
}
}
MALI_DEBUG_PRINT(4, ("Mali OSK PM: Power ref released (%u)\n", _mali_osk_atomic_read(&mali_pm_ref_count)));
#endif
}
_mali_osk_errcode_t mali_kernel_core_validate_mali_phys_range( u32 phys_base, u32 size )
{
MALI_CHECK_GOTO( 0 == ( phys_base & (~_MALI_OSK_CPU_PAGE_MASK)), failure );
MALI_CHECK_GOTO( 0 == ( size & (~_MALI_OSK_CPU_PAGE_MASK)), failure );
if ( phys_base >= mem_validator.phys_base
&& (phys_base + size) >= mem_validator.phys_base
&& phys_base <= (mem_validator.phys_base + mem_validator.size)
&& (phys_base + size) <= (mem_validator.phys_base + mem_validator.size) )
{
MALI_SUCCESS;
}
failure:
MALI_PRINTF( ("*******************************************************************************\n") );
MALI_PRINTF( ("MALI PHYSICAL RANGE VALIDATION ERROR!\n") );
MALI_PRINTF( ("\n") );
MALI_PRINTF( ("We failed to validate a Mali-Physical range that the user-side wished to map in\n") );
MALI_PRINTF( ("\n") );
MALI_PRINTF( ("It is likely that the user-side wished to do Direct Rendering, but a suitable\n") );
MALI_PRINTF( ("address range validation mechanism has not been correctly setup\n") );
MALI_PRINTF( ("\n") );
MALI_PRINTF( ("The range supplied was: phys_base=0x%08X, size=0x%08X\n", phys_base, size) );
MALI_PRINTF( ("\n") );
MALI_PRINTF( ("Please refer to the ARM Mali Software Integration Guide for more information.\n") );
MALI_PRINTF( ("\n") );
MALI_PRINTF( ("*******************************************************************************\n") );
MALI_ERROR( _MALI_OSK_ERR_FAULT );
}